Fabrication of antifouling membranes by blending poly(vinylidene fluoride) with cationic polyionic liquid

Membrane fouling problem is now limiting the rapid development of membrane technology. A newly synthesized cationic polyionic liquid (PIL) [P(PEGMA-co-BVIm-Br)] was blended with poly(vinylidene fluoride) (PVDF) to prepare antifouling PVDF membranes. The PVDF/P(PEGMA-co-BVIm-Br) exhibited an increased surface hydrophilicity, the water contact angle was reduced from 77.8° (pristine PVDF) to 57.9°. More porous membrane structure was obtained by adding PIL into the blending polymers, as high as 478.0 L/m²·h of pure water flux was detected for the blend PVDF membrane in comparison with pristine PVDF (17.2 L/m²·h). Blending of the cationic PIL with PVDF gave a more positive surface charge than pristine PVDF membrane. Blend membranes showed very high rejection rate (99.1%) and flux recovery rate (FRR, 83.0%) to the positive bovine serum albumin (BSA), due to the electrostatic repulsion between the membrane surface and proteins. After three repeated filtration cycles of positive BSA, the blend PVDF membranes demonstrated excellent antifouling performance, the permeation flux of the membranes was recovered very well after a simple deionized water washing, and as high as 70% of FRR was obtained, the water flux was maintained at above 350 L/m²·h. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2020 , 137, 48878.     

Preparation and characterization of antifouling poly(vinylidene fluoride) blended membranes

Poly(vinylidene fluoride) (PVDF) membranes have been widely used in microfiltration and ultrafiltration because of their excellent chemical resistance and thermal properties. However, PVDF membranes have exhibited severe membrane fouling because of their hydrophobic properties. In this study, we investigated the antifouling properties of PVDF blended membranes. Antifouling PVDF blended membranes were prepared with a PVDF‐g‐poly(ethylene glycol) methyl ether methacrylate (POEM) graft copolymer. The PVDF‐g‐POEM graft copolymer was synthesized by the atom transfer radical polymerization (ATRP) method. The chemical structure and properties of the synthesized PVDF‐g‐POEM graft copolymer were determined by NMR, Fourier transform infrared spectroscopy, and gel permeation chromatography. To investigate the antifouling properties of the membranes, we prepared microfiltration membranes by using the phase‐inversion method, which uses various PVDF/PVDF‐g‐POEM concentrations in dope solutions. The pure water permeabilities were obtained at various pressures. The PVDF/PVDF‐g‐POEM blended membranes exhibited no irreversible fouling in the dead‐end filtration of foulants, including bovine serum albumin, sodium alginate, and Escherichia coli broth. However, the hydrophobic PVDF membrane exhibited severe fouling in comparison with the PVDF/PVDF‐g‐POEM blended membranes. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Preparation of PVDF/poly(tetrafluoroethylene‐co‐vinyl alcohol) blend membranes with antifouling propensities via nonsolvent induced phase separation method

Poly(vinylidene fluoride) (PVDF) was blended with a new amphiphilic copolymer, poly(tetrafluoroethylene‐co‐vinyl alcohol) [poly(TFE‐VA)], via non‐solvent induced phase separation (NIPS) method to make membranes with superior antifouling properties. The effects of the VA/TFE segment ratio of the copolymer and the copolymer/PVDF blend ratio on the properties of the prepared membranes were studied. Membranes with similar water permeabilities, surface pore sizes, and rejection properties were prepared and used in bovine serum albumin (BSA) filtrations with the same initial water flux and almost the same operating pressure, to evaluate the sole effect of membrane material on fouling propensity. While the VA/TFE segment ratio strongly affected the membrane antifouling properties, the effects of the copolymer/PVDF blending ratio were not so drastic. Membrane surface hydrophilicity increased, and BSA adsorption and fouling decreased upon blending a small amount of amphiphilic copolymer with a high VA/TFE segment ratio with PVDF (copolymer/PVDF blending ratio 1:5). © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43780.     

Preparation of high‐flux ultrafiltration membranes by blending strongly charged polymer

Three kinds of high‐flux ultrafiltration membranes were fabricated by blending strongly charged polymer [sulfonated poly(phenylene oxide) (SPPO)] with neutral polymer [cellulose acetate (CA), polyethersulfone (PES), or polyvinylidene fluoride (PVDF)]. After blending with SPPO, the pure water flux of CA‐SPPO, PES‐SPPO, and PVDF‐SPPO membrane increase by 3, 76, and 30 times at a transmembrane pressure of 100 kPa. Compared with the unblended membranes, the pore radius of CA‐SPPO, PES‐SPPO, and PVDF‐SPPO membrane increased from 31.9 to 33.2 nm, 26.1 to 28.6 nm, and 19.8 to 25.7 nm, respectively. The addition of strongly charged polymer decreased the thermodynamic stability of casting solutions, promoting the phase inversion process and resulting in highly porous structure. The charged groups and hydrophilicity of the polymer facilitate the formation of an additive concentration gradient (more additive in the active layer), endowing the blend membrane with better hydrophilicity and greater wettability gradient. The high porosity, good hydrophilicity, and larger wettability gradient enable the high permeation of blend membranes. This work shows how the strongly charged polymer affects the formation and performance of blend membrane, which will be useful for designing high‐performance membrane. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44570.     

Synthesis of well‐defined amphiphilic block copolymers via AGET ATRP used for hydrophilic modification of PVDF membrane

A well‐defined amphiphilic block copolymer consisting of a hydrophobic block poly(methyl methacrylate) (PMMA) and a hydrophilic block poly[N,N–2‐(dimethylamino) ethyl methacrylate] (PDMAEMA) was synthesized by activator generated by the electron transfer for atom transfer radical polymerization method (AGET ATRP). Kinetics study revealed a linear increase in the graph concentration of PMMA‐b‐PDMAEMA with the reaction time, indicating that the polymer chain growth was consistent with a controlled process. The gel permeation chromatography results indicated that the block copolymer had a narrow molecular weight distribution (Mw/Mn = 1.42) under the optimal reaction conditions. Then, poly(vinylidene fluoride) (PVDF)/PMMA‐b‐PDMAEMA blend membranes were prepared via the standard immersion precipitation phase inversion process, using the block copolymer as additive to improve the hydrophilicity of the PVDF membrane. The presence and dispersion of PMMA‐b‐PDMAEMA clearly affected the morphology and improved the hydrophilicity of the as‐synthesized blend membranes as compared to the pristine PVDF membranes. By incorporating 15 wt % of the block copolymer, the water contact angle of the resulting blend membranes decreased from pure PVDF membrane 98° to 76°. The blend membranes showed good stability in the 20 d pure‐water experiment. The bovine serum albumin (BSA) absorption experiment revealed a substantial antifouling property of the blend membranes in comparison with the pristine PVDF membrane. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42080.     

氧化石墨烯改性PVDF超滤膜制备及分离性能

用N-（三甲氧基硅丙基）乙二胺三乙酸钠（EDTS）对氧化石墨烯进行修饰,制备出亲水的EDTS-GO纳米复合物。然后通过共混的方式将EDTS-GO添加到PVDF中,制备出EDTS-GO改性PVDF超滤膜。接触角分析和红外光谱结果表明,在相转化过程中EDTS-GO转移至膜表面,PVDF膜表面的亲水性增强。系统考察了不同EDTS-GO添加量对膜性能的影响。膜性能测试表明,随着EDTS-GO添加量的增加,PVDF膜的纯水通量先增大然后降低,当添加量为0.5%时,纯水通量达到最大值,711.2 L·（m²·h）^-1。此外,抗污染实验表明,EDTS-GO改性的PVDF超滤膜比未改性的PVDF超滤膜具有更强的抗污染性能。     

Improving the charged and antifouling properties of PVDF ultrafiltration membranes by blending with polymerized ionic liquid copolymer P(MMA‐b‐MEBIm‐Br)

This study describes the fabrication and properties of poly(vinylidene fluoride) (PVDF) filtration membranes modified by blending with ionic liquid block copolymer P(MMA‐b‐MEBIm‐Br), which is synthesized via reversible addition‐fragmentation chain transfer polymerization method. The attenuated total reflectance‐Fourier transform infrared spectroscopy and X‐ray photoelectron analyses reveal that the ionic liquid block copolymers are immobilized on PVDF membrane surface. The modified PVDF membrane exhibits excellent charged and antifouling properties because of the charged and hydrophilic properties of the copolymer. Scanning electron microscopy and atomic force microscopy also indicate the morphological characteristics of the membrane and demonstrate that the surface porous structure becomes denser after adding the copolymer. The data of filtration and the zeta potential of the membranes suggest that the charged properties of the ionic liquid block copolymers are mainly responsible for the improvement of the reversible fouling ratio and the decrease in the total fouling ratio of the membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44751.     

Evaluation of the antifouling and photocatalytic properties of novel poly(vinylidene fluoride) membranes with a reduced graphene oxide–Bi2WO6 active layer

Immobilization of reduced graphene oxide (RGO)–Bi₂WO₆ is an ideal method for obtaining antifouling membranes for membrane distillation (MD) processes. Poly(vinylidene fluoride) membranes modified with RGO–Bi₂WO₆ were successfully obtained with a double‐layer coating method through non‐solvent‐induced phase separation. The water contact angle was improved by about 30° by RGO–Bi₂WO₆; this indicated that the surface modification obviously increased the membrane hydrophobicity. The high desalination rate proved that all of the prepared membranes were appropriate for the MD process. The RGO–Bi₂WO₆‐modified membranes achieve 26.26%–59.95% removal rates in 10 mg/L aqueous ciprofloxacin under visible light for 7.5 h. It was possible to erase strongly bound foulants and recover the prepared membrane's permeation flux by 3 h of visible‐light irradiation. The RGO–Bi₂WO₆‐modified membrane with a high hydrophobicity, fouling mitigation, and photocatalytic capability presents huge potential for the treatment of high‐salt antibiotic wastewater use in the MD process. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45426.     

Mixed Matrix PVDF/Graphene and Composite‐Skin PVDF/Graphene Oxide Membranes Applied in Membrane Distillation

This work elucidates the influence of graphene (G) and graphene oxide (GO) content on the desalination performance and scaling characteristics of G/polyvinylidene fluoride (G/PVDF) mixed matrix and GO/PVDF composite‐skin membranes, applied in a direct contact membrane distillation process (DCMD). Inclusion of high quality, nonoxidized, monolayered graphene sheets as polymer membrane filler, and application of a novel GO/water‐bath coagulation method for the preparation of the GO/PVDF composite films, took place. Water permeability and desalination tests via DCMD, revealed that the optimal G content was 0.87 wt%. At such concentration the water vapor flux of the G/PVDF membrane was 1.7 times that of the nonmodified reference, while the salt rejection efficiency was significantly improved (99.8%) as compared to the neat PVDF. Similarly the GO/PVDF surface‐modified membrane, prepared using a GO dispersion with low concentration (0.5 g/L), exhibited twofold higher water vapor permeate flux as compared to the neat PVDF, but however, its salt rejection efficiency was moderate (80%), probably due to pore wetting during DCMD. The relatively low scaling tendency observed for both G and GO modified membranes is primarily attributed to their smoother surface texture as compared to neat PVDF, while scaling is caused by the deposition of calcite crystals, identified by XRPD analysis. POLYM. ENG. SCI., 59:E262–E278, 2019. © 2018 Society of Plastics Engineers     

Facile surface modification of PVDF microfiltration membrane by strong physical adsorption of amphiphilic copolymers

To endow the surface of poly(vinylidene fluoride) (PVDF) microfiltration (MF) membranes with hydrophilicity and antifouling property, physical adsorption of amphiphilic random copolymers of poly(ethylene glycol) methacrylate (PEGMA) and poly(methyl methacrylate) (PMMA) (P(PEGMA‐r‐MMA)) onto the PVDF membrane was performed. Scanning electron microscopy (SEM) images showed that the adsorption process had no influence on the membrane structure. Operation parameters including adsorption time, polymer concentration, and composition were explored in detail through X‐ray photoelectron spectroscopy (XPS), static water contact angle (CA), and water flux measurements. The results demonstrated that P(PEGMA‐r‐MMA) copolymers adsorbed successfully onto the membrane surface, and hydrophilicity of the PVDF MF membrane was greatly enhanced. The antifouling performance and adsorption stability were also characterized, respectively. It was notable that PVDF MF membranes modified by facile physical adsorption of P(PEGMA₅₈‐r‐MMA₃₃) even showed higher water flux and better antifouling property than the commercial hydrophilic PVDF MF membranes. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3112–3121, 2013     

Studies on the surface properties of mixed‐matrix membrane and its antifouling properties for humic acid removal

A major factor limiting the use of ultrafiltration (UF) membrane in water treatment process is the membrane fouling by natural organic matter such as humic acid (HA). In this work, neat PVDF and PVDF/TiO₂ mixed‐matrix membranes were prepared and compared in terms of their antifouling properties. Two commercial types of TiO₂ namely PC‐20 and P25 were embedded to prepare the mixed matrix membranes via in situ colloidal precipitation method. The contact angles for the mixed‐matrix membranes were slightly reduced while the zeta potential was increased (more negatively charged) compared with the neat membrane. Filtration of HA with the presence of Ca²⁺ demonstrated that mixed‐matrix membrane could significantly mitigate the fouling tendency compared with the neat membrane with flux ratio (J/J₀) of 0.65, 0.70, and 0.82 for neat PVDF membrane, PVDF/TiO₂ mixed‐matrix membrane embedded with P25 and PC‐20, respectively. PC‐20 with higher anatase polymorphs exhibited better antifouling properties due to its hydrophilicity nature. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Poly(arylene sulfide sulfone) hybrid ultrafiltration membrane with TiO2‐g‐PAA nanoparticles: Preparation and antifouling performance

Poly(arylene sulfide sulfone) (PASS) is a kind of newly developed polymeric membrane material which has excellent mechanical strength, thermal stability, and solvent resistance. And, it would be a potential material for high temperature ultrafiltration and organic solvent filtration. In this article, PASS hybrid ultrafiltration membrane with improved antifouling property was prepared by mixing TiO₂ nanoparticles which were grafted with polyacrylic acid (PAA). These membranes were prepared by a phase inversion technique and their separation performance and antifouling property of the prepared membranes were investigated in detail by SEM, FTIR, EDS, contact angle goniometry, filtration experiments of water, and BSA solution. The results shown that the TiO₂‐g‐PAA nanoparticles dispersed well in membrane matrix, the hydrophilicity of the membranes prepared within TiO₂‐g‐PAA nanoparticles have been improved and these membranes exhibited excellent water flux and antifouling performance in separation than that of the pure PASS membranes and PASS membranes with TiO₂ nanoparticles. More specifically, among membrane sample M0, M1.5, and MP1.5, MP1.5 which contained 1.5 wt% TiO₂‐g‐PAA exhibited the highest water permeation (190.4 L/m² h at 100 kPa), flux recovery ratio, and the lowest BSA adsorption amount. POLYM. ENG. SCI., 55:2829–2837, 2015. © 2015 Society of Plastics Engineers     

Development of mesoporous titanium dioxide hybrid poly(vinylidene fluoride) ultrafiltration membranes with photocatalytic properties

A photocatalytic activity ultrafiltration membrane (UFM) was prepared by the blending of a poly(vinylidene fluoride) (PVDF) polymer with mesoporous titanium dioxide (M‐TiO₂) particles via the phase‐inversion method. The microstructure of the membrane and Ti element distribution were characterized by scanning electron microscopy and energy‐dispersive X‐ray spectroscopy. Their properties were also determined by thermogravimetric analysis, differential scanning calorimetry, Fourier transform infrared spectroscopy, tensile stress tests, contact angle tests, bovine serum albumin retention, water flux, and permeation flux. When the M‐TiO₂ concentration reached 1 wt %, the thermal stability, mechanical properties, hydrophilicity, flux, and antifouling performance of the M‐TiO₂/PVDF UFM were improved to an optimal value with the M‐TiO₂ particles successfully entrapped and evenly distributed throughout the PVDF polymer matrix. Compared with the P25‐modified PVDF UFM (1 wt %), the M‐TiO₂‐modified PVDF UFM (1 wt %) exhibited better photocatalytic activity and wonderful stability in the UV photocatalytic degradation of the organic dye Rhodamine B. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43427.     

Development of antifouling poly(vinyl chloride) blend membranes by atom transfer radical polymerization

In this study, antifouling poly(vinyl chloride) (PVC) blend membranes were prepared by blending the PVC based amphiphilic copolymer PVC‐g‐poly(hydroxyethyl methacrylate) (PVC‐g‐PHEMA), synthesized by atom transfer radical polymerization (ATRP), into the hydrophobic PVC matrix via the nonsolvent‐induced phase separation method. The in situ ATRP reaction solutions were also used as the blend additives to improve membrane performance. Attenuated total reflectance–Fourier transform infrared spectroscopy and X‐ray photoelectron spectroscopy indicated that the blend membranes based on the two blend routes exhibited similar surface chemical compositions. The membrane morphology and surface wettability were determined by scanning electronic microscopy and water contact angle measurement, respectively. The blend membranes showed improved water permeability, comparable rejections and enhanced antifouling properties compared with the pure PVC membrane. The PVC blend membranes also had excellent long‐term stability in terms of chemical compositions and fouling resistance. The results demonstrated that ATRP was a promising technique to synthesize amphiphilic copolymer and prepare stable blend antifouling membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45832.     

One‐pot synthesized poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) blended with poly(ether sulfone) to prepare blood‐compatible membranes

In this study, a random copolymer of poly(vinyl pyrrolidone‐co‐methyl methacrylate‐co‐acrylic acid) was synthesized via a one‐pot reaction with the reversible addition–fragmentation chain‐transfer method and was then blended with poly(ether sulfone) (PES) to prepare flat‐sheet membranes that were expected to have anticoagulant and antifouling properties. The synthesized copolymer was characterized by Fourier transform infrared (FTIR) and NMR spectroscopy. The molecular weights and molecular weight distributions were determined by gel permeation chromatography. Elemental analysis was used to calculate the molar ratios of vinyl pyrrolidone (VP), methyl methacrylate (MMA), and acrylic acid (AA) in the copolymer. A liquid–liquid phase‐inversion technique was used to prepare the copolymer‐blended PES membranes. X‐ray photoelectron spectroscopy and attenuated total reflectance–FTIR spectroscopy were used to investigate the copolymer on the membrane surfaces. Compared with the pristine PES membrane, the modified PES membranes showed improved hydrophilicity, low hemolysis ratios, decreased protein adsorption, and suppressed platelet adhesion. Furthermore, the thrombin time and activated partial thromboplastin time indicated that the blood compatibility of the modified PES membranes were improved. The results of the 3‐(4,5‐Dimethylthiazol‐2‐yl)‐2,5‐diphenyltetrazolium bromide (MTT) assay and the cell morphology suggested that the cytocompatibility increased. In addition, the modified membranes showed good protein antifouling properties. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 4284–4298, 2013     

Amphiphilic PVDF-g-PDMAPMA ultrafiltration membrane with enhanced hydrophilicity and antifouling properties

It is easy to adsorb the pollutants from water owning to the hydrophobicity of the poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membrane. To improve the hydrophilicity of the PVDF UF membrane, a novel amphiphilic copolymer PVDF-g-poly-N-(3-dimethylaminopropyl)methacrylamide] (PDMAPMA) was developed. The amphiphilic PVDF-g-PDMAPMA was synthesized with PVDF and N-(3-dimethylaminopropyl)methacrylamide (DMAPMA) via free-radical polymerization, and characterized by Fourier transform infrared spectroscopy and ¹H nuclear magnetic resonance. The scanning electron microscopy and energy dispersive X-ray spectroscopy were used to characterize the structure morphologies and elementals of the blend PVDF membranes, respectively. The pure water flux (PWF), molecular weight cutoff, and bovine serum albumin (BSA) solution filtration experiments were tested to evaluate the permeation performance and antifouling properties of the membranes. The experimental results showed that the PWF was 263.1 L m⁻² h⁻¹, BSA rejection rate was 98.1% and flux recovery rate was 95.1% of the prepared blend membrane which had obvious improvement compared with the pristine PVDF membrane (17.3 L m⁻² h⁻¹, 91.0, and 83.8%, respectively). The antibacterial activity test showed the prepared blend membrane had good potency against microorganisms. A novel hydrophilic PVDF membrane with good antibacterial properties was developed and would be promising for wastewater treatment. © 2019 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2019 , 136, 48049.     

Antifouling enhancement of PVDF membrane tethered with polyampholyte hydrogel layers

The preparation and property of antifouling poly(vinylidene fluoride) (PVDF) membrane tethered with polyampholyte hydrogel layers were described in this work. In fabricating these membranes, the [2‐(methacryloyloxy)ethyl] trimethylammonium chloride and 2‐acrylamide‐2‐methyl propane sulfonic acid monomers were grafted onto the alkali‐treated PVDF membrane to yield polyampholyte hydrogel layers via radical copolymerization with N,N′‐methylenebisacrylamide as crosslinking agent. The analyses of fourier transform infrared attenuated total reflection spectroscopy and X‐ray photoelectron spectroscopy confirm the covalent immobilization of polyampholyte hydrogel layer on PVDF membrane surface. The grafting density of polyampholyte hydrogel layer increases with the crosslinking agent growing. Especially for the membrane with a high grafting density, a hydrogel layer can be observed obviously, which results in the complete coverage of membrane pores. Because of the hydrophilic characteristic of grafted layer, the modified membranes show much lower protein adsorption than pristine PVDF membrane. Cycle filtration tests indicate that both the reversible and irreversible membrane fouling is alleviated after the incorporation of polyampholyte hydrogel layer into the PVDF membrane. This work provides an effective pathway of covalently tethering hydrogel onto the hydrophobic membrane surface to achieve fouling resistance. POLYM. ENG. SCI., 55:1367–1373, 2015. © 2015 Society of Plastics Engineers     

高通量抗污染氧化石墨烯膜研究进展

水资源短缺与水污染是21世纪人类面临的共同挑战之一。膜技术具有低能耗和低成本等优点，是一种绿色高效的水处理技术。氧化石墨烯具有分子级的厚度和优异的化学稳定性，是一种优异的二维膜材料，在水处理膜领域具有重要应用前景。综述了氧化石墨烯膜在水处理领域的研究进展，针对膜技术面临的通量低和膜污染的挑战，以氧化石墨烯膜通道和表面构建中的介尺度问题为重点，探讨了不同尺度插层材料对氧化石墨烯膜通道结构与分离性能的影响，并分析了氧化石墨烯膜抗污染表面构建策略及对不同尺度污染物的抗污染机制。最后，对高通量抗污染氧化石墨烯膜研究进行了总结和展望。     

Tris(hydroxymethyl)aminomethane polyamide thin‐film‐composite antifouling reverse osmosis membrane

For the applications of reverse osmosis (RO) process, membrane fouling caused by organic molecule adsorption is still a serious problem which significantly decreases membrane lifespan and increases operation costs. In this present article, we report the thin film composite (TFC) RO membrane functionalized with tris(hydroxymethyl)aminomethane (THAM) using one‐step method for improved antifouling property. The results of surface characterization indicated that THAM was successfully grafted onto the active layer of membrane by covalent linkage. Mult‐hydroxyl‐layer was generated and remained steadily on TFC membrane surface after modification. The contact angle decreased from 75.9 ± 3.0° to 46.9 ± 2.3°, which showed a distinct improvement of membrane surface hydrophilicity after modification. The grafted THAM improved water flux by 28.3%, while salt rejection was almost unchanged in membrane property tests. The modified membranes presented preferable antifouling property to foulants of bovine serum albumin, sodium alginate, and dodecyl trimethyl ammonium bromide than that of pristine membranes during dynamic fouling experiments. The method in this study provided an effective way to improve antifouling property of the polyamide thin‐film‐composite RO membrane. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45891.     

Preparation of enduringly antifouling PVDF membrane with compatible zwitterionic copolymer via thermally induced phase separation

The compatible zwitterionic copolymers of poly(methyl methacrylate [3‐(methacryloylamino)propyl]dimethyl(3‐sulfopropyl)ammonium‐hydroxide) p(MMA‐MPDSAH) with different MPDSAH ratio are synthesized by free radical polymerization. A serial of copolymers are obtained successfully with narrow molecular weight dispersion. The MPDSAH branch ratio varies from 5% to 20%. It is initially applied to fabricate enduringly antifouling poly(vinylidene fluoride) (PVDF) membrane through a simple approach of blending by thermally induced phase separation (TIPS). The influence of zwitterionic copolymer on membrane morphology is studied by scanning electron microscopy. It was proven effective to improve the hydrophilic property of PVDF membrane as the water contact angles dramatically decreased from 80° to 40°, leading to a significant enhancement of antifouling ability. The absorbed bull serum albumin (BSA) content on modified membranes has cut almost 50%. The residual content of p(MMA‐MPDSAH) in membrane is over 40% and able to reach 80% even at vigorous rinsing by controlling copolymer structure. It guarantees the modified membrane has vested enduringly antifouling ability. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41362.