UV/H2O2氧化联合Ca(OH)2吸收同时脱硫脱硝

在小型紫外光-鼓泡床反应器中,对UV/H₂O₂氧化联合Ca(OH)₂吸收同时脱除燃煤烟气中NO与SO₂的主要影响因素[H₂O₂浓度、紫外光辐射强度、Ca(OH)₂浓度、NO浓度、溶液温度、烟气流量以及SO₂浓度]进行了考察。采用烟气分析仪和离子色谱仪分别对尾气中的NO₂和液相阴离子作了检测分析。结果显示:在本文所有实验条件下,SO₂均能实现完全脱除。随着H₂O₂浓度、紫外光辐射强度和Ca(OH)₂浓度的增加,NO的脱除效率均呈现先大幅度增加后轻微变化的趋势。NO脱除效率随烟气流量和NO浓度的增加均有大幅度下降。随着溶液温度和SO₂浓度的增加,NO脱除效率仅有微小的下降。离子色谱分析表明,反应产物主要是SO₄^2-和NO₃^-,同时有少量的NO₂^-产生。尾气中未能检测到有害气体NO₂。     

UV/H2O2氧化联合CaO吸收脱除NO的传质-反应动力学

在实验室规模的光化学反应器中,基于实验研究﹑动力学理论以及双膜理论,研究了UV/H₂O₂氧化联合CaO吸收(UV/H₂O₂-CaO工艺)脱除燃煤烟气中NO的传质-反应动力学。分析了NO吸收的传质-反应过程,明确了NO吸收过程的主要控制步骤和强化措施,测定了关键的动力学参数,推导了NO吸收过程的理论模型。结果表明:在实验范围内,NO吸收速率随着NO浓度的增加几乎呈线性增加。随着H₂O₂浓度和CaO浓度的增加,NO的吸收速率均呈现先增加后变缓的趋势。UV/H₂O₂-CaO工艺脱除NO是一个拟一级快速反应过程,强化气相主体扰动﹑增加气液接触面积和提高NO分压可有效提高NO的吸收速率。NO吸收速率方程的计算值和实验值具有较好的一致性。     

SO2 and NO removal from flue gas over V2O5/AC at lower temperatures — role of V2O5 on SO2 removal

Supporting V₂O₅ onto an activated coke (AC) has been reported to significantly increase the AC's activity in simultaneous SO₂ and NO removal from flue gas. To understand the role of V₂O₅ on SO₂ removal, V₂O₅/AC is studied through SO₂ removal reaction, surface analysis, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR) techniques. It is found that the main role of V₂O₅ in SO₂ removal over V₂O₅/AC is to catalyze SO₂ oxidation through a VOSO₄-like intermediate species, which reacts with O₂ to form SO₃ and V₂O₅. The SO₃ formed transfers from the V sites to AC sites and then reacts with H₂O to form H₂SO₄. At low V₂O₅ loadings, a V atom is able to catalyze as many as 8 SO₂ molecules to SO₃. At high V₂O₅ loadings, however, the number of SO₂ molecules catalyzed by a V atom is much less, due possibly to excessive amounts of V₂O₅ sites in comparison to the pores available for SO₃ and H₂SO₄ storage.     

Study of intrinsic sulfidation behavior of Fe2O3 for high temperature H2S removal

Iron-based sorbent was preferable for desulfurization from coal-derived gas due to economic consideration and favorable dynamic property. The intrinsic behavior of Fe-based sorbent should be primarily understood in the sulfidation process for improving its performance. A series of tests were carried out with Fe₂O₃, Fe and other compounds containing-Fe (FO) made from the same precursor FeC₂O₄·2H₂O in H₂S-N₂ mixture in this study. The formation of H₂ was observed with Fe and FO as sorbents. While SO₂ was detected with FO and Fe₂O₃ as sorbents, its concentration in outlet was gradually decreased. The crystal phase and surface chemical state of fresh and sulfided Fe₂O₃ with different reaction times were characterized by XRD and XPS measurements. The result suggested that the intrinsic H₂S removal by Fe₂O₃ would produce multi-phase of sulfides. The possible mechanism of sulfidation reaction was discussed.     

Direct synthesis of H2O2 acid solutions on carbon cathode prepared from activated carbon and vapor-growing-carbon-fiber by a H2/O2 fuel cell

Direct synthesis of H₂O₂ acid solutions was studied using a gas-diffusion cathode prepared from activated carbon (AC), vapor-growing-carbon-fiber (VGCF) and poly-tetra-fluoro-ethylene (PTFE) powders, with a new H₂/O₂ fuel cell reactor. O₂ reduction to H₂O₂ was remarkably enhanced at the three-phase boundary (O₂(g)-electrode(s)-acid(l)) at the [AC + VGCF] cathode. Fast diffusion processes of O₂ to the active surface and of H₂O₂ to the bulk acid solutions were essential for H₂O₂ accumulation. Synergy of AC and VGCF was observed for the H₂O₂ formation. RRDE and cyclic voltammetry studies indicated that the surface of AC functioned as the active phase for O₂ reduction to HO₂, and VGCF functioned as an electron conductor and a promoter to convert HO₂ to H₂O₂. A maximum H₂O₂ concentration of 353 mM (1.2 wt%) was accomplished under short-circuit conditions (current density 12.7 mA cm⁻², current efficiency 40.1%, geometric area of cathode 1.3 cm², reaction time 6 h).     

Removal of Hg0 from containing‐SO2/NO flue gas by ultraviolet/H2O2 process in a novel photochemical reactor

A novel photochemical spray reactor is first developed and is used to remove Hg⁰ and simultaneously remove Hg⁰/SO₂/NO from flue gas by ultraviolet (UV)/H₂O₂ process. The effects of several parameters (UV wavelength, UV power, H₂O₂ concentration, Hg⁰ inlet concentration, solution temperature, liquid–gas ratio, solution pH, SO₂ concentration, NO concentration, and O₂ concentration) on removal of Hg⁰ by UV/H₂O₂ process were investigated. Removal mechanism of Hg⁰ is proposed and simultaneous removal of Hg⁰, NO, and SO₂ is also studied. The results show that the parameters, UV wavelength, UV power, H₂O₂ concentration, liquid–gas ratio, solution pH, and O₂ concentration, have significant impact on removal of Hg⁰. However, the parameters, Hg⁰ inlet concentration, solution temperature, SO₂ concentration, and NO concentration, only have small effect on removal of Hg⁰. Hg²⁺ is the final product of Hg⁰ removal, and Hg⁰ is mainly removed by oxidations of H₂O₂, ·OH, · O, O₃, and photoexcitation of UV. © 2014 American Institute of Chemical Engineers AIChE J, 60: 2275–2285, 2014     

Activity and characterization of Rh/Al2O3 and Rh-Na/Al2O3 catalysts for the SCR of NO with CO in the presence of SO2 and HCl

SO₂ and HCl are major pollutants emitted from waste incineration processes. Both pollutants are difficult to remove completely and can enter the catalytic reactor. In this work, the effects of SO₂ and HCl on the performance of Rh/Al₂O₃ and Rh-Na/Al₂O₃ catalysts for NO removal were investigated in simulated waste incineration conditions. The characterizations of the catalysts were analyzed by BET, SEM/EDS, XRD, and ESCA. Experimental results indicated the 1%Rh/Al₂O₃ catalyst was significantly deactivated for NO and CO conversions when SO₂ and HCl coexisted in the flue gas. The addition of between 2 and 10 wt.% Na promoted the activity of the 1%Rh/Al₂O₃ catalyst for NO removal, but decreased the CO oxidation and BET surface area. The catalytic activity for NO removal was inhibited by HCl as a result of the formation of RhCl₃. Adding Na to the Rh/Al₂O₃ catalyst decreased the inhibition of SO₂ because of the formation of Na₂SO₄, which was observed in the XRD and ESCA analyses. SEM mapping/EDS showed that more S was residual on the surface of the Rh-Na/Al₂O₃ catalyst than Cl.     

Slaughterhouse wastewater treatment by combined anaerobic baffled reactor and UV/H2O2 processes

Combined processes of biological anaerobic baffled reactor (ABR) and UV/H₂O₂ at a laboratory scale were studied to treat a synthetic slaughterhouse wastewater. In this study, the total organic carbon (TOC) loadings of 0.2-1.1 g/(L day) were used. The results revealed that combined processes had a higher efficiency to treat the synthetic slaughterhouse wastewater. Up to 95% TOC removal was obtained for an influent concentration of 973.3 mgTOC/L at the hydraulic retention time (HRT) of 3.8 days in the ABR and 3.6 h in the UV photoreactor. Meanwhile, up to 97.7% and 96.6% removal of chemical oxygen demand (COD) and 5-day carbonaceous biochemical oxygen demand (CBOD₅) were observed in the ABR for the same influent concentration, respectively. Comparatively, for an influent concentration of 157.6 mgTOC/L, the UV/H₂O₂ process alone with the TOC loading of 0.06-1.9 g/(L h) was also studied, in which, up to 64.3%, 83.7%, and 84.3% of TOC, COD, and CBOD₅ removal were observed, respectively, at the HRT of 2.5 h with hydrogen peroxide (H₂O₂) concentration of 529 mg/L. It was found that individual ABR and UV/H₂O₂ processes enhanced the biodegradability of the treated effluent by an increased CBOD₅/COD ratio of 0.4 to 0.6. An optimum H₂O₂ dosage of 3.5 (mgH₂O₂)/(mgTOC_in h) was also found for the UV/H₂O₂ process.     

Dye decomposition kinetics by UV/H2O2: Initial rate analysis by effective kinetic modelling methodology

The wastewater from textile industries containing non-biodegradable and toxic dye compounds is one important sources of environmental contamination. This study aims at investigating the decomposition of azo dye by UV/H₂O₂ process with varying H₂O₂ concentrations, dye concentrations, initial pHs, and UV irradiation powers. The results show that the initial rate increases with increase in initial H₂O₂ concentration, initial dye concentration to a certain point and then decreases with further increase in the above factors; the initial rate remains almost constant at lower pH and then decreases with increase in pH; the initial rate linearly increases with increase in UV irradiation power. A comprehensive kinetic model, based on reaction network analysis, was developed to predict the effects of H₂O₂ concentration, dye concentration, solution pH, and UV irradiation power on the initial dye reaction rate. The experimental data and the predicted results are in good agreement.     

Low cost coal-based carbons for combined SO2 and NO removal from exhaust gas

The aim of this paper is to show how a cheap carbonaceous material such as low rank coal-based carbon (or char) can be used in the combined SO₂/NO removal from exhaust gas at the linear gas velocity used in commercial systems (0.12 m s⁻¹). Char is produced from carbonization and optionally activated with steam. This char is used in a first step to abate the SO₂ concentration at the following conditions: 100 °C, space velocity of 3600 h⁻¹, 6% O₂, 10% H₂O, 1000 ppmv SO₂, 1000 ppmv NO and N₂ as remainder. In a second step, when the SO₂ concentration in the flue gas is low, NO is reduced to N₂ and steam at the following experimental conditions: 150 °C, space velocity of 900 h⁻¹, 6% O₂, 10% H₂O, 0-500 ppmv SO₂, 1000 ppmv NO, 1000 ppmv NH₃ and N₂ as remainder.It has been shown that the presence of NO has no effect on SO₂ abatement during the first step of combined SO₂/NO removal system and that low SO₂ inlet concentration has a negligible effect on NO reduction in the second step. Moreover, this char can be thermally regenerated after use for various cycles without loss of activity. On the other hand, this regenerated char shows the highest NO removal activity (compared to parent chars, either carbonized or steam activated) which can be attributed to the activating effect of the sulfuric acid formed during the first step of the combined SO₂/NO removal system.     

Preparation and electrochemical studies of metal–carbon composite catalysts for small-scale electrosynthesis of H2O2

Numerous transition metal–carbon composite catalysts (M = V, Zn, Ni, Sn, Ce, Ba, Fe, Cu) have been synthesized and tested for electroreduction of O₂ to H₂O₂, The activity and selectivity of all synthesized catalysts for electrosynthesis of H₂O₂ were determined by the rotating ring-disk electrode method in acidic and neutral electrolytes. The Co-based catalysts in general showed the highest activity towards H₂O₂ formation. Experiments with different loading contents of Co showed that the activation overpotential losses of oxygen reduction to H₂O₂ reduces as loading increases to about 4 wt% Co. Addition of Co beyond this level did not seem to impact the overpotential losses. The cobalt-based catalysts, were spray-coated onto 120 μm thick Toray^® graphite substrates, and were studied in bulk electrolysis cells for up to 100 h at potentiostatic conditions (0.25 V vs. RHE) in pH 0, 3, and 7 electrolytes. At (25 °C and 1 bar) with a catalysts loading of about and using dissolved O₂ in 0.5 M H₂SO₄, typical H₂O₂ electrosynthesis rates of about were reached with current efficiencies of about 85 ± 5% at 0.25 V (vs. RHE).     

Simultaneous Removal of NO and SO2 from Flue Gas by UV/H2O2/CaO

The effects of several influencing factors (CaO and H₂O₂ concentration, gas flow, solution temperature, NO, SO₂, O₂ and CO₂ concentration) on the simultaneous removal of NO and SO₂ from flue gas by using a UV/H₂O₂/CaO process were studied. In addition, the anions in the liquid phase were measured by ion chromatography and the material balances for NO and SO₂ were calculated. It was found that, under all experimental conditions, this process achieved a SO₂ removal efficiency of 100 %. With the increase in CaO concentration, NO removal efficiency first increased and then remained almost unchanged. With the increase in H₂O₂ concentration, NO removal efficiency increased but the changes gradually became smaller. NO removal efficiency greatly decreased with increasing gas flow, NO concentration and CO₂ concentration. Slightly increasing the solution temperature and SO₂ concentration reduced NO removal efficiency. Increasing O₂ concentration can promote the removal of NO. The anions in the liquid phase were mainly SO₄^2– and NO₃^–. Most of the low valence nitrogen elements in NO and the low valence sulfur elements in SO₂ transformed into the high valence nitrogen element in NO₃^– and the high sulfur element in SO₄^2–.     

Influence of low concentration of SO2 for selective reduction of NO by C3H8 in lean-exhaust conditions on the activity of Ag/Al2O3 catalyst

The effect of SO₂ for the selective reduction of NO by C₃H₈ on Ag/Al₂O₃ was investigated in the presence of excess oxygen and water vapor. The NO_x conversion decreased permanently even in the presence of a low concentration of SO₂ (0.5–10 ppm) at <773 K. The increase in SO₂ concentration resulted in a large decrease in NO_x conversion at 773 K. However, when the reaction temperature was more than 823 K, the activity of Ag/Al₂O₃ remained constant even in the presence of 10 ppm of SO₂. The sulfate species formed on the used Ag/Al₂O₃ were characterized by a temperature programmed desorption method. The sulfated species formed on silver should mainly decrease the deNO_x activity on the Ag/Al₂O₃. The sulfated Ag/Al₂O₃ was appreciably regenerated by thermal treatment in the deNO_x feed at 873 K. The moderate activity remains at 773 K in the presence of 1 ppm SO₂ for long time by the heat treatment at every 20 h intervals.     

Reduction and oxidation properties of Fe2O3/ZrO2 oxygen carrier for hydrogen production

Fe₂O₃ is a promising oxygen carrier for hydrogen production in the chemical-looping process. A set of kinetic studies on reduction with CH₄, CO and H₂ respectively, oxidation with water and oxygen containing Ar for chemical-looping hydrogen production was conducted. Fe₂O₃ (20 wt.%)/ZrO₂ was prepared by a co-precipitation method. The main variables in the TGA (thermogravimetric analyzer) experiment were temperatures and gas concentrations. The reaction kinetics parameters were estimated based on the experimental data. In the reduction by CH₄, CO and H₂, the reaction rate changed near FeO. Changes in the reaction rate due to phase transformation were observed at low temperature and low gas concentration during the reduction by CH₄, but the phenomenon was not remarkable for the reduction by CO and H₂. The reduction rate achieved using CO and H₂ was relatively faster than achieved using CH₄. The Hancock and Sharp method of comparing the kinetics of isothermal solid-state reactions was applied. A phase boundary controlled model (contacting sphere) was applied to the reduction of Fe₂O₃ to FeO by CH₄, and a different phase boundary controlled model (contacting infinite slab) was fit well to the reduction of FeO to Fe by CH₄. The reduction of Fe₂O₃ to Fe by CO and H₂ can be described by the former phase boundary controlled model (contacting sphere). This phase boundary controlled model (contacting sphere) also fit well for the oxidation of Fe to Fe₃O₄ by water and FeO to Fe₂O₃ by oxygen containing Ar. These kinetics data could be used to design chemical-looping hydrogen production systems.     

Catalytic removal of NO in waste incineration processes over Rh/Al2O3 and Rh–Na/Al2O3: Effects of particulates,heavy metals,SO2 and HCl

Two novel catalysts Rh/Al₂O₃ and Rh–Na/Al₂O₃ were prepared for NO removal and tested their practical performances in a laboratory-scale waste incineration system. The effects of particulates, heavy metals, and acid gases on the catalysts were evaluated and investigated through several characterization techniques, such as SEM, EA, XRPD, ESCA, and FTIR. The results indicated that the NO conversions were increased with the accumulation of particulates on the surface of catalysts, which was attributed to the increase in carbon content. However, the increase in heavy metals Cd and Pb contents on the surface of catalysts decreased the activity of catalyst for NO removal but did not change the chemical state of Rh and Na. The Rh/Al₂O₃ catalysts were poisoned when the acid gases SO₂ and HCl were present in the flue gas, because Rh and Al reacted with S and Cl to form inactive products. Adding Na to Rh/Al₂O₃ catalysts produced a promoting effect for SO₂ removal due to the formation of Na₂SO₄. The influence levels of different pollutants on the performances of Rh/Al₂O₃ and Rh–Na/Al₂O₃ catalysts for NO removal followed the sequence of HCl > heavy metals > SO₂ > particles.     

Evaluation of electrical energy per order (EEO) with kinetic modeling on the removal of Malachite Green by US/UV/H2O2 process

The kinetics of decolorization of Malachite Green (MG) as a model cationic dye from textile industry, by US/UV/H₂O₂ process, was investigated with nonlinear regression analysis. The experimental results indicated that the decolorization kinetics of MG in this process fit well by pseudo-first order kinetics. With nonlinear regression analysis a model was developed for pseudo-first order constant (k_ap) as a function of operational parameters such as initial concentrations of H₂O₂ (25-600 mg l^− 1) and MG (1.82-9.87 mg l^− 1), temperature (294-307 K) and power density (0.049-0.16 W ml^− 1) as following:

     

Selective oxidation of methanol to dimethoxymethane over acid-modified V2O5/TiO2 catalysts

Selective oxidation of methanol to dimethoxymethane (DMM) was conducted in a fixed-bed reactor over an acid-modified V₂O₅/TiO₂ catalyst. The influence of the acid modification on its structure, redox and acidic properties, and catalytic performance for methanol oxidation were investigated. The results indicated that the content of vanadia in the catalyst exhibits a vital influence on the dispersion of vanadium species, while the acid modification can enhance its surface acidity. Proper amounts of the acid (W() = 15%) and V₂O₅ (W(V₂O₅) = 15%) components loaded in the acid-modified V₂O₅/TiO₂ catalyst are able to build a bi-functional circumstance that is favorable for the formation of DMM with high activity and selectivity. As a result, for the selective oxidation of methanol, the H₂SO₄-modified V₂O₅/TiO₂ catalyst gives a much higher DMM yield at 150 °C than the unmodified one.     

Adsorption and oxidation of NH3 over V2O5/AC surface

V₂O₅/AC has been reported to be active for selective catalytic reduction (SCR) of NO with NH₃ at around 200 °C and resistant to SO₂ deactivation. To elucidate its SCR mechanism, adsorption and oxidation of NH₃ over V₂O₅/AC are studied in this paper using TG, MS and DRIFTS techniques. It is found that the adsorption and oxidation of NH₃ take place mainly at VO bond of V₂O₅. A higher V₂O₅ loading results in more NH₃ adsorption on the catalyst. V₂O₅ contains both Brnsted and Lewis acid sites; NH₄⁺ on Brnsted acid sites is less stable and easier to be oxidized than NH₃ on Lewis acid sites. Gaseous O₂ promotes interaction of NH₃ with AC and oxidation of NH₃ over V₂O₅/AC. NH₃ is oxidized into NH₂ and acylamide structures and then to isocyanate species, which is an intermediate for N₂ formation.     

Electrochemical anticorrosion performance evaluation of Al2O3 coatings deposited by MOCVD on an industrial brass substrate

Alumina (Al₂O₃) coatings of different thickness were deposited on OT59 brass substrate (BS) using the metal organic chemical vapour deposition (MOCVD) technique to evaluate the corrosion performance by EIS measurements. The used precursor was dimethyl-aluminium-isopropoxide. Electrochemical characterizations of the deposited films were performed in a standard very aggressive acidic solution (aerated 1N H₂SO₄ at 25 °C up to 168 h of immersion time) by means of direct current method (Tafel curves) and electrochemical impedance spectroscopy (EIS). The Rutherford backscattering spectroscopy (RBS) indicated that the films are very pure with the correct Al₂O₃ stoichiometry, while the IR absorption spectra showed that the films did not contain any OH groups. The surface film morphology was investigated by atomic force microscopy (AFM) and displayed a globular texture. The films were very smooth, with a maximum root mean square roughness, for example, of 14 nm for a 0.96 μm thick coating. The EIS data confirmed, as expected, that a 2.40 μm Al₂O₃ layer ensures the best corrosion protection after 168 h of immersion in the very acidic environment used.