Mechanical and tribological properties of nano/micro composite alumina coatings fabricated by atmospheric plasma spraying

Adding nano particles can significantly improve the mechanical properties and wear resistance of thermal sprayed Al₂O₃ coating. However, it still remains a challenge to uniformly incorporate nano particles into traditional coatings due to their bad dispersibility. In the present work, nanometer Al₂O₃ (n-Al₂O₃) powders modified by KH-560 silane coupling agent were introduced into micrometer Al₂O₃ (m-Al₂O₃) powders by ultrasonic dispersion to afford nano/micro composite feedstock, and then four resultant coatings (weight fraction of n-Al₂O₃: 0%, 3%, 5% and 10%) were fabricated by atmospheric plasma spraying. The features and constitutes of feedstock and as-sprayed coatings, as well as their porosity, bonding strength, microhardness and frictional behaviors were investigated in detail. Results show that the nano/micro composite feedstock with uniform microstructure can be better melted in the spraying process, thereby obtaining coatings with denser microstructure, higher hardness and bonding strength. Added n-Al₂O₃ has no obvious effect on the friction coefficient of composite coatings, whereas can improve their wear-resistant and reduce the worn degree of counterpart. The wear mechanism of traditional coating is brittle fracture and lamellar peeling, while that of composite coating with weight fraction of n-Al₂O₃ of 10% is adhesive wear.     

Low pressure plasma-sprayed Al2O3 and Al2O3/SiC nanocomposite coatings from different feedstock powders

This paper describes a preliminary investigation of a nanocomposite ceramic coating system, based on Al₂O₃/SiC. Feedstock Al₂O₃/SiC nanocomposite powder has been manufactured using sol-gel and conventional freeze-drying processing techniques and then low pressure plasma sprayed onto stainless steel substrates using a CoNiCrAlY bond coat. Coatings of a commercial Al₂O₃ powder have also been manufactured as a reference for phase transformations and microstructure. The different powder morphology and size distribution resulting from the different processing techniques and their effect on coating microstructure has been investigated. Phase analysis of the feedstock powders and of the as-sprayed coatings by X-ray diffractometry (XRD) and nuclear magnetic resonance (NMR) showed that the nano-scale SiC particles were retained in the composite coatings and that equilibrium α-Al₂O₃ transformed to metastable γ- and δ-Al₂O₃ phases during plasma spraying. Other minority phases in the sol-gel Al₂O₃/SiC nanocomposite powder such as silica and aluminosilicate were removed by the plasma-spraying process. Microstructure characterisation by scanning electron microscopy (SEM) of the as-sprayed surface, polished cross-section, and fracture surface of the coatings showed evidence of partially molten and unmolten particles incorporated into the predominantly lamella microstructure of the coating. The extent of feedstock particle melting and consequently the character of the coating microstructure were different in each coating because of the effects of particle morphology and particle size distribution on particle melting in the plasma.     

Comprehensive study on corrosion protection properties of Al2O3, Cr2O3 and Al2O3–Cr2O3 ceramic coatings deposited by plasma spraying on carbon steel

In this study, individual Al₂O₃ and Cr₂O₃ coatings and Cr₂O₃-25, 50, 75 wt% Al₂O₃ composite coatings were applied on carbon steel by atmospheric plasma spraying method. Corrosion experiments were performed on as-sprayed and epoxy resin sealed coatings including potentiodynamic polarization, electrochemical impedance spectroscopy and long-term immersion in 3.5 wt% NaCl solution. Phase composition and microstructure of the coatings were investigated by x-ray diffraction, optical microscopy and scanning electron microscopy, before and after the corrosion experiment. The results showed that the Cr₂O₃ coating exhibited the best corrosion resistance, due to the densest microstructure and highest adhesion strength. The Cr₂O₃-25 wt% Al₂O₃ coating had the highest interconnected porosities and thus had the least corrosion resistance compared to other coatings. In general, the as-sprayed coatings induced a maximum increase of 3.93 times the polarization resistance (R_p) in the polarization experiment and a 3.5 times increase in the charge transfer resistance (R_ct) in the EIS experiment, which was not significant. Stresses caused by increased volume of corrosion products in the coating-substrate interface resulted in the spallation of Cr₂O₃-25, 50 wt% Al₂O₃ coatings from the substrate over long-term of immersion. The adhesion strength of the coatings was a determining criterion for the long-term durability of the coatings. The sealing treatment resulted in a significant increase in R_p and R_ct.     

Influence of different introduction modes of metal Ag into plasma sprayed Al2O3 coating on tribological properties

Al₂O₃ coating and Al₂O₃/Ag (10%) composite coating were prepared on the surface of GH4169 superalloy by the atmospheric plasma spraying technology. And an in-situ synthesis method was applied to introduce the Ag particles into a part of Al₂O₃ coatings to obtain Al₂O₃/Ag(synthesis) composite coating. Then, the microstructure and mechanical properties of these three Al₂O₃-based coatings were systematically studied in this work. In order to reveal the lubrication characteristics of Ag, their friction tests were carried out at room temperature (RT), 400 °C, 600 °C and 800 °C, respectively. The results showed that both microstructure and mechanical properties of Al₂O₃/Ag(synthesis) composite coating were better than that of Al₂O₃/Ag (10%) composite coating because many pores and cracks produced during the direct spraying. Although the friction coefficients of two kinds of composite coatings were close to that of Al₂O₃ coatings at RT, their wear rates were both greatly decreased due to the introduction of Ag. In addition, the lubricating performance of Ag was not enough to reduce their friction coefficients when friction temperature is lower than 600 °C. However, the friction coefficients of these composite coatings were both reduced to about 0.3 at 800 °C . At this time, the Al₂O₃/Ag(synthesis) composite coating also exhibited a lower wear rate because of its dense microstructure and excellent mechanical properties.     

Effect of plasma sprayed and laser re-melted Al2O3 coatings on hardness and wear properties of stainless steel

Commercially available austenic stainless steel substrate was coated with commercially available, raw Al₂O₃ powder applied by means of plasma spraying method and then re-melted with CO₂ laser beam of various parameters. Tribological and mechanical properties of the 120 J/mm and 160 J/mm laser re-melted coatings were compared with the tribological and mechanical properties of the “as-sprayed” coating. The influence of the laser beam of various parameters on the microstructure, phase constituents, and mechanical and tribological properties of the ceramic coating was investigated by means of scanning electron microscopy, light microscopy, computer tomography, X-ray diffraction technique and nanoindentation tests. The micro sliding wear performance of the coatings was tested using a nanoindenter. The study showed an improvement of the mechanical and tribological properties caused by the laser treatment. The best results were achieved for coating re-melted with 120 J/mm laser beam.     

Microstructure and properties of niobium carbide composite coatings prepared by plasma spraying

Niobium carbide composite coatings were prepared on titanium alloy surface by plasma spraying NbC–Al₂O₃, Nb–SiC and Nb–SiC–Al composite powders, respectively. The phase composition, microstructure and formation mechanism of the three composite coatings were analyzed and their microhardness, toughness and scratch resistance were compared. The phases of the NbC–Al₂O₃ system did not change during the plasma spraying process, and new phases (Nb₂C, NbC and Nb₃Si) were formed in the Nb–SiC and Nb–SiC–Al systems. TEM results of the Nb–SiC composite coating indicate that the new phases nanocrystalline Nb₂C, submicron NbC and nanocrystalline Nb₃Si were formed during the plasma spraying process. Compared with the NbC–Al₂O₃ composite coating, the microstructure of the Nb–SiC and the Nb–SiC–Al composite coatings were uniform, and the porosity were relatively low, and the hardness was higher. The Nb–SiC–Al composite coating was denser than the Nb–SiC composite coating, the lamellar structure was obvious and the number of pores in the coating was the least, which is attributed to the better molten state of the composite powder by the addition of the Al to the Nb–SiC system. The Nb–SiC–Al composite coating had better toughness and scratch resistance.     

Ablation behaviors of ZrC-TiC coatings prepared by vacuum plasma spray: Above 2000 °C

ZrC-TiC coatings were fabricated by vacuum plasma spray and their ablation resistance were evaluated and compared with ZrC-SiC coating by a plasma flame with a heat flux of 4.02 MW/m². The microstructure and phase compositions of the as-sprayed and ablated coatings were characterized and the function of TiC addition on the ablation resistance was investigated. The results showed that the ablation resistance of the ZrC-TiC coating was much better than that of the ZrC-SiC coating under the present ablation conditions. The decrease of surface temperatures with the increasing of TiC content were observed. (Zr, Ti)O₂ eutectic phase in liquid state was observed. The low vapor and decomposition pressures of TiO₂, combined with the formation of (Zr, Ti)O₂ liquid contributed to the excellent ablation resistance of the ZrC-TiC coating. This work affirmed that TiC could be an ideal addition to improve the ablation resistance of the ZrC coating in harsh environment above 2000 °C.     

Nanostructured ceramic composite coating prepared by reactive plasma spraying micro-sized Al–Fe2O3 composite powders

Nanostructured ceramic matrix composite coating was prepared in-situ by reactive plasma spraying micro-sized Al-Fe₂O₃ composite powders. The microstructure, toughness and Vickers hardness of these coatings were investigated by X-ray diffraction, scanning electron microscopy, transmission electron microscopy and mechanical tests. The results indicated that the coating exhibited nanostructures which consisted of FeAl₂O₄, Al₂O₃, Fe (or Fe solid solution) and a little FeAl. The composite coating showed significantly higher toughness and wear resistance than the conventional Al₂O₃ coating.     

In situ (Al,Cr)2O3-Cr composite coating fabricated by reactive plasma spraying

In situ (Al,Cr)₂O₃-Cr composite coating was fabricated by reactive plasma spraying Al-Cr₂O₃ composite powder. Phase composition and microstructure of the as-sprayed coating was characterized by X-ray diffractometer, scanning electron microscope and transmission electron microscope. Indentation fracture behavior of the coating was investigated. It is found that the microstructure of the coating consists of [(Al,Cr)₂O₃+Cr] eutectic and Cr+[(Al,Cr)₂O₃+Cr] hypoeutectic. The eutectic microstructure of the coating shows the characteristic of nano structure, in which Cr particles with size less than 40 nm distribute in (Al,Cr)₂O₃ solid solution matrix. The hypoeutectic microstructure of the coating consists of Cr particles with size larger than 1 µm and [(Al,Cr)₂O₃+Cr] divorced eutectic. The toughness of the (Al,Cr)₂O₃-Cr composite coating is significantly improved compared with that of the conventional Al₂O₃ coating.     

Fabrication of high-quality alumina coating through novel,dual-particle aerosol deposition

High-quality alumina (Al₂O₃) coating has an extensive demand in the fields of optoelectronics, solar cells, and corrosion/impurity resistant coatings and cutting tools. The quality of alumina coating depends on its hardness and transparency. To obtain hard and highly transparent alumina coating, which is also a widely used ceramic material, a novel, aerosol deposition approach is presented in which the starting powder, used to fabricate Al₂O₃ ceramic coatings, is composed of angular and spherical Al₂O₃ particles. Films fabricated using angular:spherical Al₂O₃ particle mixtures with ratios of 10:0, 7:3, 5:5, 3:7, and 0:10, showed significant variation in surface roughness and microstructure. The dramatic morphology modulation of the 3:7 angular:spherical Al₂O₃ mixture film, resulting from the superposition hammering effect caused by the aerosol mixture, improved transmittance (84.7%) and hardness (13.6 GPa). Previous studies used high-energy approaches to optimize Al₂O₃ film properties. This dual-particle approach, however, produces Al₂O₃ film with excellent transmittance and hardness while achieving a fast coating speed (32 mm² × μm/min) without additional thermal treatment. Our proposed approach provides a novel and energy efficient method to produce transparent Al₂O₃ films with superior durability.     

Nickel–alumina graded coatings obtained by dipping and EPD on nickel substrates

Nickel substrates have been coated by Ni/Al₂O₃ composite films by a dipping process using aqueous suspensions that contain a temporary binder. Two-layer and three-layer graded coatings have been produced, consisting of pure Ni powder and Ni/Al₂O₃ composites with Al₂O₃ contents of 15 and 30 vol.% as intermediate layers to release sintering and thermal stresses. The laminates were further coated with a ceramic layer of Al₂O₃/ZrO₂ that was deposited by electrophoretic deposition using a non-aqueous suspension. A continuous, thin Al₂O₃ layer surrounding Ni grains developed at the intermediate composite layer of Ni/Al₂O₃ allows the ceramic coating to maintain strongly adhered to the nickel substrate by means of a porous substrate/coating interface.     

Solution precursor high-velocity oxy-fuel spray ceramic coatings

For the first time, the solution precursor high-velocity oxy-fuel spray process was used to deposit Al₂O₃–ZrO₂ ceramic coatings. X-ray diffraction analysis and transmission electron microscopy characterization show that the as-sprayed coating is composed of mixed nanocrystalline ZrO₂ and γ-Al₂O₃ as well as amorphous phases. The as-sprayed coating consists of ultrafine splats with diameters ranging from 2 to 5 μm. Few spherical particles, hollow-shell structures are also observed on the coating surface. Polished cross-section shows that the coating is quite dense with a thickness of 40 μm.     

Evaluation of hot corrosion behavior of CSZ,CSZ/micro Al2O3 and CSZ/nano Al2O3 plasma sprayed thermal barrier coatings

Hot corrosion is one of the main destructive factors in thermal barrier coatings (TBCs) which come as a result of molten salt effect on the coating–gas interface. Hot corrosion behavior of three types of plasma sprayed TBCs was evaluated: usual CSZ, layer composite of CSZ/Micro Al₂O₃ and layer composite of CSZ/Nano Al₂O₃ in which Al₂O₃ was as a topcoat on CSZ layer. Hot corrosion studies of plasma sprayed thermal barrier coatings (TBCs) were conducted in 45 wt% Na₂SO₄+55 wt% V₂O₅ molten salt at 1050 °C for 40 h. The graded microstructure of the coatings was examined using scanning electron microscope (SEM) and X-ray diffractometer (XRD) before and after hot corrosion test. The results showed that no damage and hot corrosion products was found on the surface of CSZ/Nano Al₂O₃ coating and monoclinic ZrO₂ fraction was lower in CSZ/Micro Al₂O₃ coating in comparison with usual CSZ. reaction of molten salts with stabilizers of zirconia (Y₂O₃ and CeO₂) that accompanied by formation of monoclinic zirconia, irregular shape crystals of YVO₄, CeVO₄ and semi-cubic crystals of CeO₂ as hot corrosion products, caused the degradation of CSZ coating in usual CSZ and CSZ/Micro Al₂O₃ coating.     

Thermophysical behavior of thermal sprayed yttria stabilized zirconia based composite coatings

The effective thermal conductivity of a composite coating depends on intrinsic thermal conductivity of the constituent phases, its characteristics (size, shape) and volume fraction of porosities. The present study concerns studying the effect of CoNiCrAlY and Al₂O₃ content on the coefficient of thermal expansion and thermal conductivity of the YSZ (YSZ-CoNiCrAlY and YSZ-Al₂O₃) based composite coatings developed by thermal spray deposition technique. The coefficient of thermal expansion and thermal conductivity of the composite coatings were measured by push rod dilatometer and laser flash techniques, respectively, from room temperature to 1000 °C. Variation in density, porosity, coefficient of thermal expansion, and thermal conductivity was observed in the composite coatings with the addition of different volume fraction of CoNiCrAlY and Al₂O₃ powders in YSZ-CoNiCrAlY and YSZ-Al₂O₃ composites, respectively. Comparison between the theoretical and experimental thermal conductivities showed a mismatch varying from 4% to 58% for YSZ-CoNiCrAlY composite coatings and from 58% to 80% for YSZ-Al₂O₃ composite coatings. Model based analyses were used to understand the mechanism of thermal conductivity reduction in the composite coatings. It was concluded that the morphology of porosities varied with composition.     

Microstructural and thermal properties of plasma sprayed mullite coatings

Thick mullite (3Al₂O₃–2SiO₂) coatings were fabricated by atmospheric plasma spraying (APS) in a mixture of crystalline and amorphous phases, as confirmed by X-ray diffraction (XRD) analysis. The coatings were isothermally heat treated in order to study recrystallization mechanism of the glassy phase. The morphology and the microstructure of both mullite feedstock and coatings were investigated by using scansion electron microscopy (SEM). The porosity of as-sprayed coating was in the range between 2 and 3% and substantially remained unchanged after thermal treatment. The thermal expansion of as-sprayed and annealed coatings was measured during heating up to the temperature of crystallization and the corresponding high-temperature extent of shrinkage was calculated. The differential scanning calorimetry (DSC) curves at different heating rates showed a sharp exothermic peak between 1243 and 1253 K, suggesting a rapid recrystallization of the amorphous phase. Finally, the heat capacity of recrystallized mullite coating was measured by DSC experiments. It was approximately 1.02 × 10³ J/kg K at 373 K and increased with increasing test temperature.     

Effects of laser surface remelting on the molten salt corrosion resistance of yttria-stabilized zirconia coatings

In the present study, atmospheric plasma-sprayed yttria-stabilized zirconia coatings were post-remelted by a continuous diode laser to improve the hot corrosion resistance for as-sprayed coatings. The coating surfaces were covered with a salt mixture (V₂O₅ and Na₂SO₄) and then subjected to a hot corrosion test at 1100?°C in air. The influence of laser parameters including power and scanning rate on the coating microstructure and corrosion resistance was investigated. Results showed that the hot corrosion resistance can be improved by producing a dense and smooth surface and reducing the coating permeability to the molten salt. The transformation of the hot corrosion mechanisms was clarified on the basis of the observed corrosion behaviors. A laser power of 1500?W and scanning rate of 9?mm/s can produce minimal surface roughness with few segmented cracks, which can provide improved performance of the hot corrosion resistance.     

Structure characterisation and mechanical properties of crystalline alumina coatings on stainless steel fabricated via sol–gel technology and fibre laser processing

The surface modification of stainless steel by coating with alumina (Al₂O₃) was carried out using sol–gel coating technology in combination with laser processing. Alumina coatings have been synthesised via a sol–gel route and deposited on stainless steel substrates by dip coating. The coated substrates were then treated with pulsed ytterbium fibre laser radiation (λ = 1064 nm) in continuous wave mode with different specific energies. The composition and structure of the coated surfaces after laser processing were characterised by ATR-FTIR, XRD, SEM and contact angle measurements, whilst the mechanical properties of modified surfaces were determined using nano-indentation. The results showed that the alumina xerogel films coated on the substrates are successfully converted into crystalline alumina ceramic coatings by the laser irradiation, the structure of resulting coatings being dependent on the irradiation conditions, with increase of laser specific energy leading to the formation of initially γ-Al₂O₃ with increasing amounts of α-Al₂O₃ at higher energy. Nano-indentation results reveal that the laser processing results in significant improvement in hardness and Young's modulus of the alumina-coated surface and, at optimum, can achieve the mechanical properties at the same level as pure α-alumina ceramic, much higher than those of the as-dried xerogel coating.     

Corrosion- and wear-resistant properties of Ni–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> composite coatings containing various forms of alumina

This article describes the effect of the addition of different phases of alumina particles on the properties of electrodeposited Ni–Al₂O₃ composite coatings. The corrosion- and wear-resistant properties of Ni–Al₂O₃ composite coatings electrodeposited from a nickel sulfamate bath containing (i) alpha-alumina particles (Ni–Al₂O₃-1), (ii) gamma-alumina particles (Ni–Al₂O₃-2), and (iii) mixture of alpha, gamma, and delta alumina particles (Ni–Al₂O₃-3) have been studied. The potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies showed superior corrosion resistance of Ni–Al₂O₃-2 composite coatings compared with other two coatings. The SEM images and EDAX spectra also corroborated well with the observed corrosion results. The pin-on-disk wear studies showed improved wear resistance of Ni–Al₂O₃-1 composite coating containing alpha alumina compared with other two coatings. The transfer of material from the pin onto the disk was evident from the optical microscopy images of the wear tracks and Raman spectra of the wear track. This study shows that the addition of pure gamma-alumina particles enhances the corrosion resistance, and that pure alpha-alumina particles enhance the wear resistance of Ni composite coatings to a greater extent.     

Additive manufactured polyamide foams with periodic grid as templates for the production of functional coated carbon-bonded alumina foam filters

For the industrial production of metal melt filters, the replica technique is established since several decades. The polyurethane foams used as templates show a rather random structure with several defects which are transferred into the final filter structure after the replication. In order to generate filters with periodic structure and low amount of defects, a periodic foam model was used and open cell foams were produced by selective laser sintering of aged polyamide 12 (PA12). The PA12 foams were then used as sacrificial templates for the replica technique in the production route of Al₂O₃-C filters with functional coatings based on a cold sprayed Al₂O₃-C coating or a flame sprayed coating based on Al₂O₃. The differences in geometry between the computer-generated model foam, the sacrificial PA12 foam, the foam after carbonization, and the additional functionalized filters with the cold and hot coating were analyzed by computed tomography. Based on CT-data isosurfaces of the foams were generated to virtualize and distinguish the differences. Preliminary mechanical tests showed a higher cold crushing strength for the filters coated via flame-spray technique than the cold coating.