The effect of system pressure on gas‐liquid slug flow in a microchannel

Characteristics of gas‐liquid two‐phase flow under elevated pressures up to 3.0 MPa in a microchannel are investigated to provide the guidance for microreactor designs relevant to industrial application. The results indicate that a strong leakage flow through the channel corners occurs although the gas bubbles block the channel. With a simplified estimation, the leakage flow is shown to increase with an increase in pressure, leading to a bubble formation shifting from transition regime to squeezing regime. During the formation process, the two‐phase dynamic interaction at the T‐junction entrance would have a significant influence on the flow in the main channel as the moving velocity of generated bubbles varies periodically with the formation cycle. Other characteristics such as bubble formation frequency, bubble and slug lengths, bubble velocities, gas hold‐up, and the specific surface area are also discussed under different system pressures. © 2013 American Institute of Chemical Engineers AIChE J, 60: 1132–1142, 2014     

Mass transfer and hydrodynamic characteristics in a co‐current downflow contacting column

Hydrodynamic and mass transfer characteristics of water–air system in a co‐current downflow contacting column (CDCC) were studied for various nozzle diameters at different superficial gas velocities and liquid re‐circulation rates. Gas hold‐up and liquid‐side mass transfer coefficient increased with increasing superficial gas velocity and liquid flow rate but decreased with increasing nozzle diameter. It is shown that correlations developed, which are based on liquid kinetic power per liquid volume present in the column, and superficial gas velocity explains gas hold‐up and the mass transfer coefficient within an error 20% for all gas and liquid flow rates and nozzle diameters used. The constants of correlations for gas hold‐up and mass transfer coefficient were found to be considerably different from other gas–liquid contacting systems. © 2003 Society of Chemical Industry     

Prediction of liquid height for onset of slug flow

An experimental investigation is carried out to study the transition from stratified to slug flow and the development of slug flow. The variation of Lockhart–Martinelli parameter with the non‐dimensional liquid height is established based on the experimental data. A correlation is developed for the liquid height as a function of superficial gas and liquid Reynolds number. The liquid height is observed to increase up to some level depending on the mass flow rate, beyond which there is a sudden jump in the height leading to the formation of slug. This critical liquid height is the limiting condition for the evolution of slug. Below the critical height a stable stratified flow is observed. The critical height for stability limit of stratified flow is established experimentally for various combinations of mass flow rates of the primary and secondary phases. © 2011 Canadian Society for Chemical Engineering     

The effect of the size of square microchannels on hydrodynamics and mass transfer during liquid‐liquid slug flow

The present study investigated the influence of square microchannel (MC) size on hydrodynamics and mass transfer in the liquid‐liquid slug flow regime. Three square MCs with the hydraulic diameters of 200, 400, and 600 μm were used. The employed method for estimating mass‐transfer coefficients remarkably increased the accuracy of the results. The findings revealed that decreasing the MC size improved the interfacial area due to plug length enlargement and deteriorated mass‐transfer resistances because of augmented internal circulations, leading to the considerable enhancement of mass‐transfer coefficients. The increasing effect on the overall mass‐transfer coefficient became greater with flow velocity, showing that size effect on mass‐transfer resistances was more profound at higher flow velocities. The influence of size on the interfacial area was significantly greater than that on mass‐transfer resistances due to the significant increment of wall film length with the decrease in channel size. © 2017 American Institute of Chemical Engineers AIChE J, 2017     

Effect of tube diameter on two‐phase flow patterns in mini tubes

The effect of tube diameter on two‐phase flow patterns was investigated in circular tubes with inner diameters of 0.6, 1.2, 1.7, 2.6, and 3.4 mm using air and water. The gas and liquid superficial velocity ranges were 0.01–50 and 0.01–3 m/s, respectively. The gas and liquid flow rates were measured and the two‐phase flow pattern images were recorded using high‐speed CMOS camera. The flow patterns observed were dispersed bubbly, bubbly, slug, slug‐annular, wavy‐annular, stratified, and annular flows. These flow patterns were not observed in all the test diameters, but were found to be unique to particular tube diameters, confirming the effect of tube diameter on the flow pattern. The data obtained were compared to existing experimental data and flow regime transition maps which show generally reasonable overall agreement at the larger diameters, but significant differences were observed with the smaller diameter tubes.     

The effect of gas‐liquid counter‐current operation on gas hold‐up in bubble columns using electrical resistance tomography

BACKGROUND: In order to improve the performance of a counter‐current bubble column, radial variations of the gas hold‐ups and mean hold‐ups were investigated in a 0.160 m i.d. bubble column using electrical resistance tomography with two axial locations (Plane 1 and Plane 2). In all experiments the liquid phase was tap water and the gas phase air. The superficial gas velocity was varied from 0.02 to 0.25 m s^?1, and the liquid velocity varied from 0 to 0.01 m s^?1. The effect of liquid velocity on the distribution of mean hold‐ups and radial gas hold‐ups is discussed. RESULTS: The gas hold‐up profile in a gas–liquid counter‐current bubble column was determined by electrical resistance tomography. The liquid velocity slightly influences the mean hold‐up and radial hold‐up distribution under the selected operating conditions and the liquid flow improves the transition gas velocity from a homogeneous regime to a heterogeneous regime. Meanwhile, the radial gas hold‐up profiles are steeper at the central region of the column with increasing gas velocity. Moreover, the gas hold‐up in the centre of the column becomes steeper with increasing liquid velocity. CONCLUSIONS: The value of mean gas hold‐ups slightly increases with increasing downward liquid velocity, and more than mean gas hold‐ups in batch and co‐current operation. According to the experimental results, an empirical correlation for the centreline gas hold‐up is obtained based on the effects of gas velocity, liquid velocity, and ratio of axial height to column diameter. The values calculated in this way are in close agreement with experimental data, and compare with literature data on gas hold‐ups at the centre of the column. Copyright © 2010 Society of Chemical Industry     

3‐D numerical simulations on flow and mixing behaviors in gas–liquid–solid microchannels

Three‐dimensional (3‐D) gas‐liquid–solid flow and mixing behaviors in microchannels were simulated by coupled volume of fluid and discrete phase method and simulations were validated against observations. The detachment time and length of gas slug are shortened in liquid–solid flow, compared with those in liquid flow due to higher superficial viscosity of liquid–solid mixture, which will move the bubble formation toward the dripping regime. Solid particles mainly distribute in liquid slug and particle flow shows obvious periodicity. With the increase of contact angle of the inner wall, gas slug (0–50°), stratified (77–120°), and liquid drop (160°) flows are observed. The residence time distributions of solid and liquid phases are similar because particles behave as tracers. The backmixing of solid and liquid phases in liquid drop flow is the weakest among the three flow patterns, and the backmixing of gas phase in slug flow is weaker than that in both stratified and liquid drop flows. The results can provide a theoretical basis for the design of microreactors. © 2013 American Institute of Chemical Engineers AIChE J, 59: 1934–1951, 2013     

壁面润湿性对微通道内二氧化碳-水两相流流动及传质性能的影响

在1 mm×1 mm矩形截面下微通道内,以二氧化碳-水为工作流体,研究壁面润湿性和气液表观流速对气-液两相流型和气液传质的影响,并研究了气、液表观流速对弹状流流体力学性质的影响。在亲水微通道中观测到了泡状流、泡状-弹状流、弹状流;在疏水微通道中观测到了非对称弹状流、拉长的非对称弹状流、分层流。实验表明亲水微通道中弹状流区域下气泡长度大体上随气相表观流速的增大而增大,随液相表观流速的增大而减小;液弹长度大体上随气相表观流速的增大而减小,随液相表观流速的增大先增大后减小;液侧体积传质系数k_La均随气、液相表观流速的增大而增大,随通道壁面润湿性的增强而增大。     

利用一维波和段塞稳定性模型预测分层流向段塞流的转变

利用气液二相流一维波模型和段塞稳定性模型,对直径2.54 cm水平管内空气-水二相流出现段塞流时的各相临界表观速度和临界液层高度进行了理论预测。计算中发现,2种模型分别适用于不同的流速区域,在较低的气相流速下,一维波模型的预测结果比较理想,但是在较高的气速条件下不太适合,而利用段塞稳定性模型可以较好地获得高流速下分层流向段塞流的流型转变条件。因此,结合这2种模型对发生流型转变时的临界参数作了分析,并且应用于40 mm和50 mm水平管道的油气二相流实验。将理论计算的结果和实验测得的流型数据进行了对比,并且对影响流型的管径、流速等因素作了分析,结果表明计算得到的特征参数和实验数据比较吻合。     

Experimental study of hydrodynamics and thermal behavior of a pseudo‐2D spout‐fluidized bed with liquid injection

A novel nonintrusive technique is presented to investigate hydrodynamic and thermal behavior of gas–solid spout‐fluidized beds with liquid injection, by simultaneously capturing visual and infrared images. Experiments were performed in a pseudo‐2D bed with draft plates filled with glass or γ‐alumina particles to investigate the effect of liquid injection and particle properties on the flow characteristics. For the glass particles under dry and wet conditions, time‐averaged particle velocities show similar quasi‐steady‐state behavior. However, under wet conditions, lower particle velocities were observed in both spout and annulus as compared with the dry system. Whereas, γ‐alumina particles do not show considerable variation in the particle velocities under dry and wet conditions and fluidize well at higher liquid injection rates. Additionally, for the glass particles, the particle temperature significantly decreases as compared to the γ‐alumina particles. © 2015 American Institute of Chemical Engineers AIChE J, 61: 1146–1159, 2015     

Counter‐current gas‐liquid wavy film flow between the vertical plates analyzed using the Navier‐Stokes equations

The article is devoted to a theoretical analysis of counter‐current gas‐liquid wavy film flow between vertical plates. We consider two‐dimensional nonlinear waves on the interface over a wide variation of parameters. The main interest is to analyse the wave structure at the parameter values corresponding to the onset of flooding observed in experiments. We use the Navier‐Stokes equations in their full statement to describe the liquid phase hydrodynamics. For the gas phase equations, we use two models: (1) the Navier‐Stokes system and (2) the simplified Benjamin‐Miles approach where the liquid phase is a small disturbance for the laminar or turbulent gas flow. With the superficial gas velocity increasing and starting from some value of the velocity, the waves demonstrate a rapid decreasing of both the minimal film thickness and the phase wave velocity. We obtain a region of the gas velocity where we have two solutions at one set of the problem parameters and where the flooding takes place. Both the phase wave velocity and the minimal film thickness are positive numbers at such values of the velocity. We calculate the flooding point dependences on the liquid Reynolds number for two different liquids. The wave regime corresponding to the flooding point demonstrates negative u‐velocities in the neighbourhood of the interface near the film thickness maximum. At smaller values of the superficial gas velocity, the negative u‐velocities take place in the neighbourhood of the film thickness minimum. © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Influence of elevated pressure and particle lyophobicity on hydrodynamics and gas–liquid mass transfer in slurry bubble columns

This article reports on the influence of elevated pressure and catalyst particle lyophobicity at particle concentrations up to 3 vol % on the hydrodynamics and the gas‐to‐liquid mass transfer in a slurry bubble column. The study was done with demineralized water (aqueous phase) and Isopar‐M oil (organic phase) slurries in a 0.15 m internal diameter bubble column operated at pressures ranging from 0.1 to 1.3 MPa. The overall gas hold‐up, the flow regime transition point, the average large bubble diameter, and the centerline liquid velocity were measured along with the gas–liquid mass transfer coefficient. The gas hold‐up and the flow regime transition point are not influenced by the presence of lyophilic particles. Lyophobic particles shift the regime transition to a higher gas velocity and cause foam formation. Increasing operating pressure significantly increases the gas hold‐up and the regime transition velocity, irrespective of the particle lyophobicity. The gas–liquid mass transfer coefficient is proportional to the gas hold‐up for all investigated slurries and is not affected by the particle lyophobicity, the particle concentration, and the operating pressure. A correlation is presented to estimate the gas–liquid mass transfer coefficient as a function of the measured gas hold‐up: $k_{\rm l}a_{\rm l}/\varepsilon_{\rm g} = 3.0 \sqrt{Du_{\rm b}/d_{\rm b}^3}\;{\rm s}^{-1}$ . © 2009 American Institute of Chemical Engineers AIChE J, 2010     

Investigating the liquid film characteristics of gas–liquid swirling flow using ultrasound doppler velocimetry

A novel gas–liquid two‐phase flow metering method was proposed. A spiral vane mounted in the inner pipe was used to transform inlet flow patterns into gas–liquid swirling annular flow. The thickness and velocity profile of liquid film were measured by ultrasound Doppler velocimetry. The liquid flow rates were obtained by integrating of velocity profile during the liquid film zone. Experiments were carried out in an air–water two‐phase flow loop and an ultrasonic transducer was installed under the bottom of the test section with the Doppler angle of 70°. The flow patterns included stratified wavy, annular, and slug flows. Compared with non‐swirling flow, the liquid film thickness at the bottom reduces greatly. The measurement accuracy of liquid flow rate was independent of inlet flow patterns, gas and liquid velocities. © 2016 American Institute of Chemical Engineers AIChE J, 63: 2348–2357, 2017     

The effect of mass transfer on flow characteristics in vertical two-phase unstable flow

Studies carried out on the absorption of hexane from inert carrier gases into paraffin oil have shown that mass transfer can affect flow characteristics in unstable vertical two-phase flow. In the absence of mass transfer chain-flow patterns prevailed. These patterns were broken when mass transfer took place from the gas to the liquid phase. Bullet shaped slugs were then formed, the slugs pairing and coalescing as they rose up the column. The direction of mass transfer was critical no effect on flow pattern being observed when mass transfer took place from the liquid to the gas phase. Slug frequencies and slug sizes were found to be influenced by mass transfer and an effect of overall absorber length was observed. Individual slug sizes and separation distances were measured and varied widely even under constant flow conditions. Rise velocities were correlated using an equation of the form:where C₂ was a function of the fluid flow-rates and system physical-properties.     

Modeling of Slug Velocity and Pressure Drop in Gas‐Liquid‐Liquid Slug Flow

Gas‐liquid‐liquid slug flow in a capillary reactor is a promising new concept that allows one to incorporate gas‐liquid reaction, liquid‐liquid extraction, and facile catalyst separation in a single unit. In order to assess the performance of a gas‐liquid‐liquid slug flow reactor, it is necessary to predict the slug velocity and pressure drop to ascertain residence times and reaction rates. New empirical models for velocity and pressure drop were developed based on existing models for two‐phase gas‐liquid and liquid‐liquid slug flows, and these were validated experimentally.     

Liquid holdup in concentric annuli during cocurrent gas‐liquid upflow

In the recent paper, an in‐depth investigation of liquid holdup during air‐water upflow through concentric annuli has been reported. The liquid holdup has been determined experimentally for the bubbly, slug and churn flow regimes. The drift flux model has been adopted for the theoretical estimation of holdup in the bubbly, dispersed bubbly and slug flow regimes. The pronounced effect of flow regime on this parameter as observed from experiments has been incorporated in the model by adopting different values of U₀, n and C₀. The asymmetry of the Taylor bubbles has been incorporated in the slug flow regime. The theoretical predictions exhibit a good agreement with the experimental data of the present work and that available in literature (Caetano et al., 1989b). The Hughmark's correlation is observed to correlate the churn flow data of the present work reasonably well.     

Sensor‐based flow pattern detection—gas–liquid–liquid upflow through a vertical pipe

Flow distribution during gas–liquid–liquid upflow through a vertical pipe is investigated. The optical probe technique has been adopted for an objective identification of flow patterns. The probability density function (PDF) analysis of the probe signals has been used to identify the range of existence of the different patterns. Dispersed and slug flow have been identified from the nature of the PDF, which is bimodal for slug flow and unimodal for dispersed flow. The water continuous, oil continuous, and emulsion type flow distributions are distinguished on the basis of the PDF moments. The method is particularly useful at high flow rates where visualization techniques fail. Based on this, a flow pattern detection algorithm has been presented. Two different representations of flow pattern maps have been suggested for gas–liquid–liquid three phase flow. © 2014 American Institute of Chemical Engineers AIChE J, 60: 3362–3375, 2014     

Hydrodynamics in a pilot‐scale cocurrent trickle‐bed reactor at low gas velocities

Hydrodynamic data obtained from laboratory‐scale trickle‐beds often fail to accurately represent industrial‐scale systems with high packing aspect ratios and column‐to‐particle diameter ratios. In this study, pressure drop, liquid holdup, and flow regime transition were investigated in a pilot‐scale trickle‐bed column of 33 cm ID and 2.45 m bed height packed with 1.6 mm × 8.4 ± 1.4 mm cylindrical extrudates for air‐water mass superficial velocities of 0.0023 – 0.094 kg/m²s and 4.5 – 45 kg/m²s, respectively, at atmospheric pressure. Significant deviation was observed from pressure drop and liquid holdup correlations at low liquid flows rates, corresponding to gravity‐driven flow limit. Likewise, liquid saturation is overestimated by correlations at high liquid flow rates, owing to significantly reduced wall effects. Lastly, trickle‐to‐dispersed bubble flow and trickle‐to‐pulsing flow regime transitions are reported using a combination of visual observations and analysis of the magnitude of local pressure fluctuations within the column. © 2018 American Institute of Chemical Engineers AIChE J, 64: 2560–2569, 2018     

Gas–liquid interfacial area and mass transfer coefficient in a co‐current down flow contacting column

The gas–liquid interfacial area and mass transfer coefficient for absorption of oxygen from air into water, aqueous glycerol solutions up to 1.5% (w/w) and fermentation medium containing glucose up to a 3% concentration were determined in a co‐current down flow contacting column (CDCC; 0.05 m i.d. and 0.8 m length). Experimental studies were conducted using various nozzle diameters at different gas and re‐circulation liquid rates. Specific interfacial area (a) is determined from the fractional gas hold‐up (ε_G) and the average bubble diameter (d_b). Once the interfacial area is determined, the volumetric mass transfer coefficient (k_La) is then used to evaluate the film mass transfer coefficient in the CDCC. The effects of operating conditions and liquid properties on the specific interfacial area were investigated. The values of interfacial area in air–aqueous glycerol solutions and fermentation media were found to be lower than those in the air–water system. As far as experimental conditions were concerned, the values of interfacial area obtained from this study were found to be considerably higher than those of the literature values of conventional bubble columns. The penetration theory is used to interpret the film mass transfer coefficient and results match the experimental k_L data reasonably well. Copyright © 2006 Society of Chemical Industry     

Measurements of horizontal three‐phase solid‐liquid‐gas slug flow: Influence of hydrate‐like particles on hydrodynamics

Gas hydrate formation is a main flow assurance concern in oil and gas production. Understanding the effects of the introduction of solid particles in the slug flow is essential to improve the efficiency and safety of multiphase production. The purpose of the present work is the experimental characterization of solid‐liquid‐gas slug flow with the presence of dispersed hydrate‐like particles. Experimental tests were carried out with inert polyethylene particles of 0.5‐mm diameter with density similar to gas hydrates (938 kg/m³). The test section comprised a 26‐mm ID, 9‐m length horizontal duct of transparent Plexiglas. High Speed Imaging and resistivity sensors was used to analyze the slug flow unit cell behavior due to the introduction of the solid particles and to measure the unit cell translational velocity, the slug flow frequency, the bubble and slug lengths, and the phase fractions. Two distinct concentrations of solid particles were tested (6 and 8 g/dm³). © 2018 American Institute of Chemical Engineers AIChE J, 64: 2864–2880, 2018