Isothermal crystallization, melting behavior and crystalline morphology of syndiotactic polystyrene blends with highly-impact polystyrene

Syndiotactic polystyrene (sPS) blends with highly-impact polystyrene (HIPS) were prepared with a twin-screw extruder. Isothermal crystallization, melting behavior and crystalline morphology of sPS in sPS/HIPS blends were investigated by differential scanning calorimetry (DSC), wide-angle X-ray diffraction (WAXD) and polarized optical microscopy (POM). Experimental results indicated that the isothermal crystallization behavior of sPS in its blends not only depended on the melting temperature and crystallization temperature, but also on the HIPS content. Addition of HIPS restricted the crystallization of sPS melted at 320 °C. For sPS melted at 280 °C, addition of low HIPS content (10 wt% and 30 wt%) facilitated the crystallization of sPS and the formation of more content of α-crystal. However, addition of high HIPS content (50 wt% and 70 wt%) restricted the crystallization of sPS and facilitated the formation of β-crystal. More content of β-crystal was formed with increase of the melting and crystallization temperature. However, α-crystal could be obtained at low crystallization temperature for the specimens melted at high temperature. Addition of high HIPS content resulted in the formation of sPS spherulites with less perfection.     

sPS/PBA-aPS共混物的结晶与熔融行为

通过熔融共混法制备了间规立构聚苯乙烯/聚丙烯酸丁酯无规立构聚苯乙烯核壳乳胶粒子（sPS/PBA-aPS）共混物,采用差示扫描量热仪、X射线衍射仪和偏光显微镜研究了PBA-aPS对sPS结晶性能、结晶形态的影响,以及共混物在不同降温速率下、等温结晶条件下所得试样的熔融行为。结果表明, PBA-aPS的引入对sPS的结晶起阻碍作用,sPS及其共混物存在明显熔融重结晶再熔融现象,sPS平衡熔点为293.2 ℃,共混物的平衡熔点随PBA-aPS含量增加而降低,sPS形成β型大球晶完善性变差,sPS/PBA-aPS共混物的冲击强度明显提高,sPS/PBA-aPS质量比为80:20时,冲击强度提高了117 %。     

Effect of the crystallization conditions on the phase behavior of syndiotactic polystyrene/poly(phenylene oxide) blends

Syndiotactic polystyrene (sPS) and poly(phenylene oxide) (PPO) blends, miscible in the melt state, were crystallized from the melt and the quenched state at different temperatures. The effect of the crystallization temperature on the phase behavior of the blends and the polymorphic changes in sPS was investigated by dynamic mechanical analysis (DMA), wide‐angle X‐ray diffraction (WAXD), and density measurements. In most blends, the crystallization of sPS induced segregation into two homogeneous amorphous phases of different compositions. The temperatures of the DMA relaxations of the neat homopolymers and crystallized blends were fit by the Gordon–Taylor relation to calculate the compositions of these phases. In melt‐crystallized blends, with slower crystallization, the major amorphous phase became sPS‐rich, whereas the minor phase became PPO‐rich. These major and minor amorphous phases could be tentatively assigned to interfibrillar and interlamellar regions, respectively. In cold‐crystallized blends, slower crystallization decreased the sPS concentration in both phases, and the scale of segregation was much smaller. WAXD studies and density measurements indicated a complex polymorphic behavior of sPS after it was blended with PPO. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1975–1983, 2003     

Crystallization behavior of syndiotactic polystyrene nanocomposites for melt‐ and cold‐crystallizations

Analyses of the effects of montmorillonite (clay) on the crystallinity and crystallization behavior of syndiotactic polystyrene (s‐PS) were investigated by Fourier transform infrared (FTIR) spectroscopy and differential scanning calorimetry (DSC). The dispersibility of the clay in s‐PS nanocomposites was studied by X‐ray and transmission electron microscopy (TEM). The clay was dispersed into the s‐PS matrix by melt blending on a scale of 1–2 nm or few tenths–100 nm, depending on the surfactant treatment. On adding clay, the crystallization behavior of the s‐PS tends to convert into the β‐crystal from the α‐crystal after being cold‐crystallized because the clay plays a vital role in facilitating the formation of the thermodynamically favored β‐form crystal when the s‐PS is cold‐ or melt‐crystallized. This phenomenon leads to a change in a conventional mechanism of molecular packing for the s‐PS. Evidently, the clay significantly affects the crystallinity and crystallization behavior of the s‐PS. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2492–2501, 2002     

Miscibility, thermal properties and polymorphism of syndiotactic polystyrene/poly(styrene-co-α-methyl styrene) blends

This work examined the miscibility, crystallization kinetics, melting behavior and crystal structure of syndiotactic polystyrene (sPS)/poly(styrene-co-α-methyl styrene) blends. Differential scanning calorimetry, polarized light microscopy and wide angle X-ray diffraction technique were used to approach the goals. The single composition-dependent T_gs of the blends and the melting temperature (T_m) depression of sPS in the blends indicated the miscible characteristic of the blend system at all compositions. Furthermore, the T_gs of the blends could be predicted by either of the Gordon–Taylor equation (with K=0.99) or the Fox equation with a slightly higher deviation. The dynamic and isothermal crystallization abilities of sPS were hindered with the incorporation of the miscible copolymer. Complex melting behavior was observed for melt-crystallized pure sPS and its blends as well. Nevertheless, the blends showed relatively simpler melting curves. Comparing with melt-crystallized samples, the cold-crystallized samples exhibited simpler melting behavior. The equilibrium melting temperature (T_m⁰) of β form sPS crystal determined from the conventional extrapolative method is 295.2 °C. The Flory–Huggins interaction parameter, χ, of the blends was estimated to be −0.27. The crystal morphology of sPS was disturbed in the blends. Only underdeveloped granular-like crystalline superstructure of sPS exhibited in cold-crystallized blends. Moreover, the existence of the copolymer in the blends apparently reduced the possibility of forming the less stable α form sPS crystals.     

Miscibility in Blends of Isotactic/Syndiotactic Polystyrenes at Melt or Quenched Amorphous Solid State

Summary: Miscibility in amorphous phase and behavior in a crystalline phase of blends of two semicrystalline and isomeric polymers, isotactic polystyrene (iPS) and syndiotactic polystyrene (sPS), was probed. Optical and scanning electron microscopy results indicate no discernible heterogeneity in iPS/sPS blends in either melt state or rapidly quenched amorphous super‐cooled state, while the T_g behavior of the quenched amorphous blends shows an intimately mixed state of two polymer chains. The crystal forms of the blends were further analyzed to provide additional evidence of miscibility in the amorphous domain. The sPS in the iPS/sPS blends upon melt crystallization was found to predominantly exist as the more stable β‐form (rather than mixed β‐form and α‐form in neat sPS), which also suggests evidence of miscibility in the iPS/sPS blends. The melting behavior of semicrystalline sPS in the iPS/sPS mixtures was analyzed using the Flory‐Huggins approach for estimation of interactions. By measuring the equilibrium melting point of the higher‐melting sPS species in the sPS/iPS blends, a small negative value, for the interaction parameter (χ ≈ ?0.11) was found. Further, by introducing a third polymer, poly(2,6‐dimethyl‐p‐phenylene oxide) (PPO), a ternary iPS/sPS/PPO blend system was also proven miscible, which constituted a further test for stable phase miscibility in the iPS/sPS blend. General nature of miscibility in blends composed of two crystalline isomeric polymers is discussed. Issues in dealing with blends of polymers of the same chemical repeat unit but different tacticities were addressed.

X‐ray diffractograms for neat sPS and iPS/sPS blends, each having been isothermally crystallized at 245 °C for 4 h.     

Morphology,structure, and kinetic analysis of nonisothermal cold‐ and melt‐crystallization of syndiotactic polystyrene

Nonisothermal cold‐ and melt‐crystallization of syndiotactic polystyrene (sPS) were carefully carried out by Perkin–Elmer Diamond differential scanning calorimetry, polarized optical microcopy (POM), and wide angle X‐ray diffraction. The experimental data subjected to the two types of processing were thoroughly analyzed on the basis of Avrami, Tobin, Ziabicki, and combination of Avrami and Ozawa models. Avrami, Tobin, and Ziabicki analyses indicate that nonisothermal cold‐crystallization (A) characterizes smaller Avami and Tobin exponent and larger Ziabicki kinetic crystallizability index G than those obtained from nonisothermal melt‐crystallization (B) possibly due to the existence of partially ordered structures in the quenched samples. Kissinger and the differential isoconversional method (DICM) of Friedman's were utilized to obtain effective energy barrier of A, in good agreement with that obtained by using Arrhenius equation to analyze the isothermal cold‐crystallization, indicating that Kissinger and Friedman equations can be applied to obtain activation energy from A of sPS. X‐ray diffraction analysis indicates that cold‐crystallization mainly produces α‐type crystal but for melt‐crystallization the contents of α‐type and β‐type crystals depend on the cooling rates. The POM also indicates the difference of end morphology of the sample between A and B. At the same time, the DICM of Friedman's was applied to analyze experimental data of B, which were divided into two groups with 20 K/min as the threshold, and it was found that the formation of β‐type crystal possesses larger absolute value of effective activation barrier than the formation of α‐type crystal. © 2006Wiley Periodicals, Inc. J Appl Polym Sci 103: 1311–1324, 2007     

The atactic polystyrene molecular weight effect on the thermal properties and crystal structure of syndiotactic polystyrene/atactic polystyrene blends

This work examined how the molecular weight of atactic polystyrene (aPS) affects the thermal properties and crystal structure of syndiotactic polystyrene (sPS)/aPS blends using differential scanning calorimetry, polarized light microscopy and wide angle X-ray diffraction (WAXD) technique. For comparative purposes, the structure and properties of the parent sPS was also investigated. The experimental results indicated that these blends showed single glass transition temperatures (T_gs), implying the miscibility of these blends in the amorphous state regardless of the aPS molecular weight. The non-isothermal and isothermal melt crystallization of sPS were hindered with the incorporation of aPSs. Moreover, aPS with a lower molecular weight caused a further decrease in the crystallization rate of sPS. Complex melting behavior was observed for parent sPS and its blends as well. The melting temperatures of these blends were lower than those of the parent sPS, and they decreased as the molecular weight of aPS decreased. Compared with the results of the WAXD study, the observed complex melting behavior resulted from the mixed polymorphs (i.e. the α and β forms) along with the melting-recrystallization-remelting of the β form crystals during the heating scans. The degree of melting-recrystallization-remelting phenomenon for each specimen was dependent primarily on how fast the sPS crystals were formed instead of the incorporation of aPSs. Furthermore, the existence of aPS in the blends, especially the lower molecular weight aPS, apparently reduced the possibility of forming the less stable α form in the sPS crystals.     

The formation of β‐polypropylene crystals in a compatibilized blend of isotactic polypropylene and polyamide‐6

Compatibilized polypropylene (PP)/polyamide (PA6) blends with and without β nucleating agent (β‐NA) are prepared, and are designated as Blend‐0.3 and Blend‐0, respectively. The melting and crystallization characteristic of the blends crystallized under different cooling rates and different crystallization temperatures are studied. It is observed that high β‐PP content can be developed in Blend‐0.3 only at slow cooling rates (<5°C/min), whereas high α‐PP content is formed at fast cooling rates. Isothermal crystallization analysis of Blend‐0 indicates that PA6 is an effective NA for α‐PP in the lower temperature range, whereas the α‐nucleating effect disappears in the higher temperature range. Blend‐0.3 can, therefore, be viewed as a system containing both α‐ and β‐NAs, simultaneously. PA6 is competing with β‐NA in inducing PP crystallization. Under the normal injection of Blend‐0.3, the melt will be cooled through the higher temperature that favors the effectiveness of β‐NA rapidly because of the faster cooling rate. However, the α‐nucleation effect from PA6 predominate at the lower temperature. This explains the difficulty in obtaining high β‐PP content in Blend‐0.3 from injection molding. POLYM. ENG. SCI., 2011. © 2010 Society of Plastics Engineers     

Effects of maleated syndiotactic polystyrene on the morphology,mechanical properties,and crystallization behavior of syndiotactic polystyrene/polyamide 6 blends

The compatibilization of syndiotactic polystyrene (sPS)/polyamide 6 (PA‐6) blends with maleic anhydride grafted syndiotactic polystyrene (sPS‐g‐MA) as a reactive compatibilizer was investigated. The sPS/PA‐6 blends were in situ compatibilized by a reaction between the maleic anhydride (MA) of sPS‐g‐MA and the amine end group of PA‐6. The occurrence of the chemical reaction was substantiated by the disappearance of a characteristic MA peak from the Fourier transform infrared spectrum. Morphology observations showed that the size of the dispersed PA‐6 domains was significantly reduced and that the interfacial adhesion was much improved by the addition of sPS‐g‐MA. As a result of reactive compatibilization, the impact strengths of the sPS/PA‐6 blends increased with an increase in the sPS‐g‐MA content. The crystallization behaviors of the blends were affected by the compatibilization effect of sPS‐g‐MA. A single melting peak of sPS in the noncompatibilized blend was gradually split into two peaks as the amount of the compatibilizer increased. A single crystallization peak of PA‐6 in the noncompatibilized blend became two peaks with the addition of 3 wt % sPS‐g‐MA. The new peak was a result of the fractionation crystallization. As the amount of sPS‐g‐MA increased, the intensity of the new peak increased, and the original peak nearly disappeared. Finally, the crystallization peak of PA‐6 disappeared with 20 wt % sPS‐g‐MA in the blend. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 2502–2506, 2003     

Effects of crystallization temperature on the polymorphic behavior of syndiotactic polystyrene

The influence of crystallization temperature on formation of the α- and β-form crystals of syndiotactic polystyrene (sPS) was investigated by X-ray diffraction and non-isothermal differential scanning calorimetry analysis. For sPS samples without any thermal history, the crystallization temperature must be the intrinsic factor controlling the formation the α and β-form crystals. Being crystallized at different cooling rate from the melt, sPS forms the β-form crystal until the temperature cooled down to about 230 °C, and α-form crystal can only be obtained when the temperature was below about 230 °C.     

Effect of crystallization conditions on spherulitic texture and tensile properties of sPS/PPO blends

In the second study on melt‐miscible syndiotactic polystyrene (sPS) and poly(phenylene oxide) (PPO) blends, the effect of processing conditions on morphology, ultimate tensile properties, and the mode of fracture is reported. Bulk samples of the blends were molded and then crystallized from melt as well as from the quenched state at different temperatures. The spherulitic morphology of the melt‐crystallized blends, observed by scanning electron microscopy, revealed formation of complete, well‐developed spherulites whose texture increased in coarseness with increasing crystallization temperatures. In all the cold‐crystallized blends lamellar bundles formed a meshlike structure whose texture did not vary significantly with crystallization temperature. Depending on the crystallization temperature, 50/50 melt‐crystallized blends showed varying tensile properties and different modes of failure. In the samples with the largest amorphous domain size of 0.6 μm, the amorphous ellipsoids were cold drawn into fibrils during tensile loading and very high tensile strengths were recorded. The tensile properties for the other melt‐crystallized and all cold‐crystallized blends did not vary substantially with the changing crystallization temperature. The micrographs of the fractured surfaces of the melt‐crystallized blends suggested that, although intraspherulitic fracture occurred at low crystallization temperatures, interspherulitic fracture took place at high crystallization temperatures. The correlation of the morphology and mechanical properties suggests that melt‐miscible blends have good interfacial adhesion between phases and that, by varying composition and processing conditions, it might be possible to control amorphous domain sizes, which is critical in achieving better mechanical properties. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 87: 1984–1994, 2003     

Pre‐melting temperature effect on the isothermal melt crystallization and multiple melting behavior of syndiotactic polystyrene

This work examined how pre‐melting temperature (T_max) affects the isothermal melt crystallization kinetics, the resulting melting behavior and crystal structure of syndiotactic polystyrene (sPS) by using differential scanning calorimetry (DSC), polarized light microscopy (PLM) and the wide angle X‐ray diffraction (WAXD) technique. Experimental results indicated that raising T_max decreased the nucleation rate and the crystal growth rate of sPS. The Avrami equation was also used to analyze the overall crystallization kinetics. The Avrami exponent n and rate constant K were determined for different T_max specimens at various crystallization temperatures (T_c's). Our results indicated that the nucleation type of sPS is T_max and T_c dependent as well. Evaluation of the activation energy for the isothermal crystallization processes revealed that it increases from 375 kJmol^?1 to 485 kjmol ^?1 with an increase of T_max. From the melting behavior study, we believe that the T_max and T_c‐dependent multiple melting peaks are associated with different polymorphs as well as recrystallized crystals formed during heating scans. Moreover, the percentage content of α form in the crystals formed under different crystallization conditions was estimated through WAXD experiments.     

Nonisothermal crystallization and melting behavior of β‐nucleated isotactic polypropylene and polyamide 66 blends

A highly novel nano‐CaCO₃ supported β‐nucleating agent was employed to prepare β‐nucleated isotactic polypropylene (iPP) blend with polyamide (PA) 66, β‐nucleated iPP/PA66 blend, as well as its compatibilized version with maleic anhydride grafted PP (PP‐g‐MA), maleic anhydride grafted polyethylene‐octene (POE‐g‐MA), and polyethylene‐vinyl acetate (EVA‐g‐MA), respectively. Nonisothermal crystallization behavior and melting characteristics of β‐nucleated iPP and its blends were investigated by differential scanning calorimeter and wide angle X‐ray diffraction. Experimental results indicated that the crystallization temperature (T) of PP shifts to high temperature in the non‐nucleated PP/PA66 blends because of the α‐nucleating effect of PA66. T of PP and the β‐crystal content (K_β) in β‐nucleated iPP/PA66 blends not only depended on the PA66 content, but also on the compatibilizer type. Addition of PP‐g‐MA and POE‐g‐MA into β‐nucleated iPP/PA66 blends increased the β‐crystal content; however, EVA‐g‐MA is not benefit for the formation of β‐crystal in the compatibilized β‐nucleated iPP/PA66 blend. It can be relative to the different interfacial interactions between PP and compatibilizers. The nonisothermal crystallization kinetics of PP in the blends was evaluated by Mo's method. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Grafted syndiotactic polystyrene synthesized via melting graft copolymerization used as a compatibilizer for immiscible syndiotactic polystyrene/polyadimide 66 blends

A new grafted syndiotactic polystyrene (g‐sPS), to be used as a compatibilizer for syndiotactic polystyrene (sPS)/polyadimide 66 blends, was prepared by the melting graft copolymerization of sPS and monomers composed of itaconic acid and dibutyl maleate with dicumyl peroxide as an initiator. The resulting g‐sPS possessed a side‐chain structure identified by IR spectra, and the results of mechanical testing show that a good impact strength and tensile strength were obtained for g‐sPS at a 7.16‐phr addition of monomer with a 3:1 proportion of dibutyl maleate and itaconic acid. Differential scanning calorimetry and scanning electron microscopy analysis indicated that the g‐sPS maintained a high glass‐transition temperature and a crystalline structure. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 97: 1659–1666, 2005     

Carbon nanocapsules-reinforced syndiotactic polystyrene nanocomposites: Crystallization and morphological features

Syndiotactic polystyrene (sPS) composites filled with well-dispersed carbon nanocapsules (CNC) were prepared through solution blending along with ultrasonication. Several analytic techniques, including DSC, FTIR, PLM, WAXD, TEM, and TGA were performed to reveal the CNC effects on the crystallization, morphology and the thermal degradation of the as-prepared sPS/CNC composites. Addition of CNC was found to favor the crystalline modification of β-form sPS and depress the α-form ones. For the dynamic crystallization, a gradual reduction of cold-crystallization temperature of the α-form sPS was observed by increasing the CNC content although the glass transition temperature remained unchanged (∼96 °C). In contrast, the melt-crystallization temperature of the β-form sPS was elevated from 238 °C for the neat sPS to 251 °C for the 99/5 composite in spite of the fact that the equilibrium melting temperature (∼290 °C) determined from the linear Hoffman-Weeks plot was irrelevant with CNC concentrations. The former was attributable to the formation of an effective heat-conduction path to trigger an earlier overall crystallization. On the other hand, the latter resulted from the enhanced nucleation sites due to the presence of uniformly dispersed CNCs. Results of the isothermal crystallization of the β-form sPS concluded that the presence of 1% CNCs led to a significant increase in the crystallization rate as much as an order of magnitude. Moreover, the Avrami exponent changed to ∼2.0 from a value of 2.8 for the neat sPS, suggesting a different crystallization mechanism involved. At a given crystallization temperature, PLM results showed a negligible variation in the crystal growth rates and a decrease in spherulitic sizes, indicating that nucleation played the key role in enhancing the crystallization rate. For samples isothermally crystallized at 260 °C, the lamellar thickness was constant to be ∼7.2 nm regardless of the CNC content. Due to the enhanced nucleation, however, lamellar stacks were more randomly oriented and its lateral dimensions became shorter with increasing CNC contents. For composites with more than 1 wt% CNC, the crystallizability of sPS chains was reduced and the annealing peak located ca. 4 °C higher than the crystallization temperature became more evident, suggesting the plausible formation of micro-crystals in between the lamellar stacks. The TGA results illustrated that a better thermal stability was reached for the CNC-filled sPS composites.     

The supermolecular structure of isotactic polypropylene/atactic polystyrene blends

The supermolecular structure of binary isotactic polypropylene/atactic polystyrene (iPP/PS) injection‐molded blends were studied by wide‐angle X‐ray diffraction, differential scanning calorimetry, and optical microscopy. The combination of different methods gives a possibility of analysis of relation between the phase transformation in polypropylene and crystallization parameters. Effect of compatibilization of poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) grafted with maleic anhydride (SEBS‐g‐MA) block copolymers in the iPP/PS blends on the structure, nucleation, crystal growth, solidification, and the phase morphology was analyzed. We found that the β‐crystallization tendency of polypropylene matrix can be enhanced by adding atactic polystyrene. However, the incorporation of SEBS‐g‐MA into iPP/PS blends resulted in an important decrease in β‐content of iPP. It is evident that the presence of compatibilizing agent caused a very significant reduction of the α‐spherulite growth rates and the crystal conversion as well as increases of half‐time crystallization in comparison with the iPP/PS systems. The relation between kinetic parameters of crystallization process and polymorphic structure of iPP in blend systems has been satisfactorily explained. Moreover, a strong effect of processing parameters on the β‐phase formation was observed. The results clearly show that at a higher temperature of mold and lower injection speed, the amount of β‐phase of iPP matrix slightly decreases. POLYM. ENG. SCI., 2011. © 2011 Society of Plastics Engineers     

Isothermal and nonisothermal crystallization kinetics of syndiotactic polystyrene/clay nanocomposites

Differential scanning calorimeter (DSC) and X‐ray diffraction methods were used to investigate the isothermal and nonisothermal crystallization behavior and crystalline structure of syndiotactic polystyrene (sPS)/clay nanocomposites. The sPS/clay nanocomposites were prepared by mixing the sPS polymer solution with the organically modified montmorillonite. DSC isothermal results revealed that introducing 5 wt% of clay into the sPS structure causes strongly heterogeneous nucleation, inducing a change of the crystal growth process from mixed three‐dimensional and two‐dimensional crystal growth to two‐dimensional spherulitic growth. The activation energy of sPS drastically decreases with the presence of 0.5 wt% clay and then increases with increasing clay content. The result indicates that the addition of clay into sPS induces the heterogeneous nucleation (a lower ΔE) at lower clay content and then reduces the transportation ability of polymer chains during crystallization processes at higher clay content (a higher ΔE). We studied the non‐isothermal melt‐crystallization kinetics and melting behavior of sPS/clay nanocomposites at various cooling rates. The correlation among crystallization kinetics, melting behavior and crystalline structure of sPS/clay nanocomposites is discussed. Polym. Eng. Sci. 44:2288–2297, 2004. © 2004 Society of Plastics Engineers.     

Blends of polyamide1010 with unmodified and maleic‐anhydride‐grafted high‐impact polystyrene

The crystallization behaviors, dynamic mechanical properties, tensile, and morphology features of polyamide1010 (PA1010) blends with the high‐impact polystyrene (HIPS) were examined at a wide composition range. Both unmodified and maleic‐anhydride‐(MA)‐grafted HIPS (HIPS‐g‐MA) were used. It was found that the domain size of HIPS‐g‐MA was much smaller than that of HIPS at the same compositions in the blends. The mechanical performances of PA1010–HIPS‐g‐MA blends were enhanced much more than that of PA1010–HIPS blends. The crystallization temperature of PA1010 shifted towards higher temperature as HIPS‐g‐MA increased from 20 to 50% in the blends. For the blends with a dispersed PA phase (≤35 wt %), the T_c of PA1010 shifted towards lower temperature, from 178 to 83°C. An additional transition was detected at a temperature located between the T_g's of PA1010 and PS. It was associated with the interphase relaxation peak. Its intensity increased with increasing content of PA1010, and the maximum occurred at the composition of PA1010–HIPS‐g‐MA 80/20. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 857–865, 1999     

Non‐isothermal crystallization and multiple melting behavior of syndiotactic polystyrene—pre‐melting temperature effects

This work investigated how pre‐melting temperature (T_max) and cooling rate (C) affected the non‐isothermal melt crystallization, melting behavior and crystal structure of syndiotactic polystyrene (sPS) by using differential scanning calorimetry (DSC) and wide angle X‐ray diffraction (WAXD) techniques. Experimental results indicated that raising T_max or C decreased the crystallization peak temperature (T_p) and crystallization initiating temperature (T_i). The crystallization kinetics was analyzed through the Ozawa equation. Although the Ozawa exponent n and cooling function K(T) were determined for T_max = 340°C and T_max = 315°C specimens, for T_max = 290°C specimens, the Ozawa equation was not applicable. Activation energies for the non‐isothermal crystallization processes of different T_max specimens were estimated to be approximately 418 kJ/mol. As T_max was raised the nucleation rate of sPS became slower. The multiple melting peaks were associated with different polymorphs as well as recrystallized crystals that formed during heating scans. The percentage content of α polymorph formed in the crystals under various crystallization conditions was estimated through WAXD experiments.