Effect of the addition of β-Si3N4 nuclei on the thermal conductivity of β-Si3N4 ceramics

Various microstructures of β-Si₃N₄ were fabricated, with or without the addition of β-Si₃N₄ seed particles to high-purity β-Si₃N₄ powder, using Yb₂O₃ and ZrO₂ as sintering additives, by gas-pressure sintering at 1950 °C for 16 h. The thermal conductivity of the specimen without seeds was 140 W·(m·K)⁻¹, and the specimen exhibited a bimodal microstructure with abnormally grown grains. The thermal conductivity of the specimen with 24 vol.% seed addition was 143 W·(m·K)⁻¹, and this specimen had the bimodal microstructure with finer grain size than that without the seeded material, but maintained the same amount of large grains (⩾2 μm in diameter) as in the specimen without the seeds. This finding indicates that the thermal conductivity of β-Si₃N₄ is controlled by the amount of reprecipitated large grains, rather than by the grain size of the β-Si₃N₄.     

Effects of Al2O3–Y2O3/Yb2O3 additives on microstructures and mechanical properties of silicon nitride ceramics prepared by hot-pressing sintering

Silicon nitride (Si₃N₄) ceramics doped with two different sintering additive systems (Al₂O₃–Y₂O₃ and Al₂O₃–Yb₂O₃) were prepared by hot-pressing sintering at 1800℃ for 2 h and 30 MPa. The microstructures, nano-indentation test, and mechanical properties of the as-prepared Si₃N₄ ceramics were systematically investigated. The X-ray diffraction analyses of the as-prepared Si₃N₄ ceramics doped with the two sintering additives showed a large number of phase transformations of α-Si₃N₄ to β-Si₃N₄. Grain size distributions and aspect ratios as well as their effects on mechanical properties are presented in this study. The specimen doped with the Al₂O₃–Yb₂O₃ sintering additive has a larger aspect ratio and higher fracture toughness, while the Vickers hardness is relatively lower. It can be seen from the nano-indentation tests that the stronger the elastic deformation ability of the specimens, the higher the fracture toughness. At the same time, the mechanical properties are greatly enhanced by specific interlocking microstructures formed by the high aspect ratio β-Si₃N₄ grains. In addition, the density, relative density, and flexural strength of the as-prepared Si₃N₄ ceramics doped with Al₂O₃–Y₂O₃ were 3.25 g/cm³, 99.9%, and 1053 ± 53 MPa, respectively. When Al₂O₃–Yb₂O₃ additives were introduced, the above properties reached 3.33 g/cm³, 99.9%, and 1150 ± 106 MPa, respectively. It reveals that microstructure control and mechanical property optimization for Si₃N₄ ceramics are feasible by tailoring sintering additives.     

Microstructure evolution of Si3N4 ceramics with high thermal conductivity by using Y2O3 and MgSiN2 as sintering additives

Silicon nitride (Si₃N₄) ceramics were prepared by gas-pressure sintering using Y₂O₃–MgSiN₂ as a sintering additive. The densification behavior, phase transition, and microstructure evolution were investigated in detail, and the relevance between the microstructure and the performance (including thermal conductivity and mechanical properties) was further discussed. A significant change from a bimodal to a homogeneous microstructure and a decreased grain size occurred with increasing Y₂O₃–MgSiN₂ content. When the small quantity of preformed β-Si₃N₄ nuclei grew preferentially and rapidly in a short time, an obvious bimodal microstructure was obtained in the sample with 4 mol% and 6 mol% Y₂O₃–MgSiN₂. When more β-Si₃N₄ nuclei grew at a relatively rapid rate, the sample with 8 mol% Y₂O₃–MgSiN₂ showed a microstructure consisting of numerous abnormally grown β-Si₃N₄ grains and small grains. When more β-Si₃N₄ nuclei grew simultaneously and slowly, there was a homogeneous microstructure and smaller grains in the sample containing 10 mol% Y₂O₃–MgSiN₂. Benefitting from the completely dense, significant bimodal microstructure, low grain boundary phase, and excellent Si₃N₄–Si₃N₄ contiguity, the sample containing 6 mol% Y₂O₃–MgSiN₂ exhibited great comprehensive performance, with a maximum thermal conductivity and fracture toughness of 84.1 W/(m⋅K) and 8.97 MPa m^1/2, as well as a flexural strength of 880.2 MPa.     

Mechanical characterization of highly porous β-Si3N4 ceramics fabricated via partial sintering & starch addition

In this study, porous β-Si₃N₄ ceramics containing limited amount of Sm₂O₃ and CaO as sintering aids were produced by addition of potato starch (10 and 20 vol.%) and partial sintering. Two different Si₃N₄ powders, α- and β-, were used as starting materials. Scanning electron microscopy investigations revealed that development of elongated β-Si₃N₄ grains were much more pronounced when α-Si₃N₄ starting powder was used. Even though porosity values of the compositions prepared by using α-Si₃N₄ (～57.0–58.4%) is significantly higher than the samples produced by β-Si₃N₄ (42.6%), no significant change was observed for the bending strength, fracture toughness and Weibull modulus. This indicates that microstructural features have a significant contribution to the mechanical properties of the porous materials in terms of bending strength and fracture toughness.     

Microstructure–permeability relation of porous β-Si3N4 ceramics

Porous β-Si₃N₄ ceramics with two distinct structures were produced by using two different Si₃N₄ sources to investigate the relationship between microstructure and permeability. Results showed that regardless of pore amount, size of pore channels, shape-distribution of β-Si₃N₄ grains are more effective on permeability of porous Si₃N₄ ceramics. Higher permeability and lower contribution of inertial forces was obtained by microstructure consists of coarse and equiaxed grains even at lower porosity amount. Calculated Forchheimer number (F_o) and measured the local breadth of a pore also supported the effect of microstructure on permeability.     

Influence of β-Si3N4 particle size and heat treatment on microstructural evolution of α:β-SiAlON ceramics

In the present study, we report the effects of starting β-Si₃N₄ particle sizes and post-sintering heat treatment on microstructure evolution and mechanical properties of prepared α-β SiAlON ceramics. Three different β-Si₃N₄ starting powders, with particle sizes of 2, 1 and 0.5 μm were used to prepare α-β SiAlON ceramics by gas-pressure sintering. Elongated β-SiAlON grain morphology was identified in the samples prepared using 0.5 μm particle size β-Si₃N₄ powder. Low-aspect ratio grain morphology was observed in samples prepared from starting powders with coarse particles (2 μm and 1 μm). The sintered samples were further heat treated to develop desired microstructure with elongated grains. The hardness and indentation fracture toughness values of sintered and heat treated samples were found to lie in the range of 12.4-14.2 GPa and 5.1-6.4 MPa m^1/2 respectively. It was revealed that fracture toughness increases with decrease in particle size of starting β-Si₃N₄ powder.     

The effect of fabrication parameters on the mechanical properties of sintered reaction bonded porous Si3N4 ceramics

Porous silicon nitride ceramics were prepared via sintered reaction bonded silicon nitride at 1680 °C. The grain size of nitrided Si₃N₄ and diameter of post-sintered β-Si₃N₄ are controlled by size of raw Si. Porosity of 42.14–46.54% and flexural strength from 141 MPa to 165 MPa were obtained. During post-sintering with nano Y₂O₃ as sintering additive, nano Y₂O₃ can promote the formation of small β-Si₃N₄ nuclei, but the large amount of β-Si₃N₄ (>20%) after nitridation also works as nuclei site for precipitation, in consequence the growth of fine β-Si₃N₄ grains is restrained, the length is shortened, and the improvement on flexural strength is minimized. The effect of nano SiC on the refinement of the β-Si₃N₄ grains is notable because of the pinning effect, while the effect of nano C on the refinement of the β-Si₃N₄ grains is not remarkable due to the carbothermal reaction and increase in viscosity of the liquid phase.     

Fabrication and wear behaviors of graded Si3N4 ceramics by the combination of two-step sintering and β-Si3N4 seeds

Graded Si₃N₄ ceramics with sandwich-like microstructure were fabricated by the combination of hot-pressing, spark plasma sintering and β-Si₃N₄ seeds. Phase compositions, microstructures, mechanical properties, and wear behaviors were investigated. Main α-Si₃N₄ phase were detected in the outer layers, and only β-Si₃N₄ phase were observed in the inner layers. The outer layer with ultra-fine equiaxed grains were well bonded to the inner layer with a distinct bimodal grain size distribution. Vickers hardness of outer layer (～21.2?GPa) was much higher than that of inner layer (～16.1?GPa), whereas fracture toughness of outer layer (～3.5?MPa?m^1/2) was much lower than that of inner layer (～5.9?MPa?m^1/2), indicative of the hard surface and tough core. Due to the ultra-fine microstructure and high hardness of outer layer, the graded Si₃N₄ ceramics exhibited superior wear resistance with low wear rate.     

Effects of N2 pressure and Si particle size on mechanical properties of porous Si3N4 ceramics prepared via SHS

Porous silicon nitride ceramics with high flexural strength and high porosity were directly fabricated by self-propagating high temperature synthesis (SHS). The effects of N₂ pressure and Si particle size on the phase composition, microstructure, and mechanical property were investigated. N₂ influences not only the thermodynamics but also the kinetics of the SHS as initial reactant. Flexural strength ranged between 67 MPa and 134 MPa with increasing N₂ pressure. On the other hand, flexural strength ranged from 213 MPa to 102 MPa with different Si particle sizes. This plays an important role on the final diameter and length of β-Si₃N₄ grains and the formation mechanism of porous Si₃N₄ ceramics.     

Microstructure and mechanical properties of α/β-Si3N4 composite ceramics with novel ternary additives prepared via spark plasma sintering

In this study, α/β-Si₃N₄ composite ceramics with high hardness and toughness were fabricated by adopting two different novel ternary additives, ZrN–AlN–Al₂O₃/Y₂O₃, and spark plasma sintering at 1550 °C under 40 MPa. The phase composition, microstructure, grain distribution, crack propagation process and mechanical properties of sintered bulk were investigated. Results demonstrated that the sintered α/β-Si₃N₄ composite ceramics with ZrN–AlN–Al₂O₃ contained the most α phase, which resulted in a maximum Vickers hardness of 18.41 ± 0.31 GPa. In the α/β-Si₃N₄ composite ceramics with ZrN–AlN–Y₂O₃ additives, Zr₃AlN MAX-phase and ZrO phase were found and their formation mechanisms were explained. The fracture appearance presented coarser elongated β-Si₃N₄ grains and denser microstructure when 20 wt% TiC particles were mixed into Si₃N₄ matrix, meanwhile, exhibited maximum mean grain diameter of 0.98 ± 0.24 μm. As a result, the compact α/β-Si₃N₄ composite ceramics containing ZrN–AlN–Y₂O₃ additives and TiC particles displayed the optimal bending strength and fracture toughness of 822.63 ± 28.75 MPa and 8.53 ± 0.21 MPa?m^1/2, respectively. Moreover, the synergistic toughening of rod-like β-Si₃N₄ grains and TiC reinforced particles revealed the beneficial effect on the enhanced fracture toughness of Si₃N₄ ceramic matrix.     

Effect of starting Si3N4 powder type and sintering conditions on grain morphology of α-SiAlON ceramics

Abstract

Nitrogen rich multication α-SiAlON ceramics doped with Y-Ce have been densified by gas pressure sintering using α-Si₃N₄ or mixed β/α-Si₃N₄ starting powder. The effects of α-SiAlON nucleation and growth mechanisms were investigated by using di fferent sintering cycles. X-ray diffraction studies after sintering revealed that 21R polytype phase was present in addition to α -SiAlON matrix phase. Microstructural characterisation of sintered materials prepared using α-Si₃N₄ powder in the starting composition revealed a typical equiaxed grain morphology, as expected if the α-SiAlON nucleation step was not applied before grain growth. However, needlelike α-SiAlON grains were observed if a nucleation step was carried out before final sintering. In starting powders containing mixed β/α-Si₃N₄, needlelike grain morphology was also observed. The effects of different Si₃N4 starting powders and sintering conditions on the grain morphology and mechanical properties are discussed.     

Effect of rare earth oxides addition on the mechanical properties and coloration of silicon nitride ceramics

The aim of this study was to evaluate the mechanical properties and coloration of silicon nitride ceramics in the presence of RE₂O₃ (RE = Nd, Eu or Dy). Dense Si₃N₄ ceramics were prepared by gas pressure sintering at 1800 °C for 2 h. XRD analysis confirmed the complete transformation of α-Si₃N4 to β-Si₃N₄. The fracture toughness and flexure strengths were 11.93 ± 0.56 MPa·m^1/2, 667 ± 40.98 MPa with the addition of Eu₂O₃ (SE). Base on the SEM image, the pull-out, bridging and deflection of large grains were observed and contributed to the increase in mechanical properties. The chromaticity of sintered bodies was measured using a spectrophotometer. The color difference of the ceramics is due to the formation of different color developing compounds according to the EDS. Results showed that high-toughness and colorful Si₃N₄ ceramics can be prepared using YAG:Ce³⁺ as sintering additive and RE₂O₃ as the colorant.     

Combustion synthesis of high flexural strength,low linear shrinkage and machinable porous β-Si3N4 ceramics

Porous β-Si₃N₄ ceramics were prepared by combustion synthesis using Si, α-Si₃N₄ and Y₂O₃ powders as raw materials. The effects of α-Si₃N₄ diluent content in pellet on nitriding rate, shrinkage, porosity and flexural strength of porous ceramics were investigated. The results show that porous β-Si₃N₄ ceramic with porosity of 49 % and flexural strength of 151 MPa can be obtained by combustion synthesis when the content of α-Si₃N₄ diluent in raw materials is equal to that of Si, and the linear shrinkage of porous ceramic is only 2.8 %. In addition, the porous ceramic can be drilled and turned by WC drill and turning tool respectively.     

Simultaneous improvement in porosity and strength of porous β-Si3N4 ceramics by formation of ultrafine fibrous grains

Si₃N₄ ceramic with ultrafine fibrous grains are expected to exhibit remarkable mechanical properties. In this work, highly porous Si₃N₄ ceramic monoliths composed of ultrafine fibrous grains were developed via a novel vapor-solid carbothermal reduction nitridation (V-S CRN) reaction between SiO vapor and green bodies comprised of carbon nanotubes (CNTs), α-Si₃N₄ diluents and Y₂O₃ in a N₂ atmosphere. The unique fibrous grains-interconnected structure was developed through in-situ formation of Si₃N₄ and following liquid phase sintering. The porous Si₃N₄ monoliths with porosity of 61–78% was developed by controlling the contents of α-Si₃N₄ diluents and densities of the CNT green bodies. With increasing of the α-Si₃N₄ contents, Si₃N₄ fibrous grains with an aspect ratio of approximate or higher than 20 could be achieved, and the grains were gradually refined. For the samples with 40 wt% α-Si₃N₄, the minimum mean grain diameter and pore size of 164 nm and 0.79 μm were achieved, respectively, and the resultant porous Si₃N₄ monolith exhibited a flexural strength of as high as 73–102 MPa with the porosity of 61–73%, which is much higher than that of the reported in literature. The improvement of mechanical strength could be attributed to the densely interconnected bird's nests structure formed by the ultrafine fibrous grains. The effects of the α-Si₃N₄ diluents on the resulting porous Si₃N₄ monolith via this method were analyzed.     

Variation of sintering parameters at an early stage of densification affecting β-Si3N4-microstructure

The influence of sintering parameters at an early stage of densification on the evolution of a bimodal microstructure in Si₃N₄ ceramics was investigated. Commonly two different methods are pursued to design a bimodal Si₃N₄ microstructure: (i) annealing at a later sintering stage (T > 1850 °C) initiating β-Si₃N₄ grain growth via Ostwald ripening and (ii) seeding with β-Si₃N₄ nuclei, which abnormally grow during the liquid-phase sintering process. In this study, a third and novel method to design Si₃N₄ microstructures by affecting intrinsic nucleation phenomena at an early sintering stage is presented. In order to study the influence of sintering parameters on β-Si₃N₄ nuclei formation during the early stage of densification, temperature and pressure were systematically changed. Starting from identical green bodies (identical processing and doping), the variation of the sintering parameters affected intrinsic β-Si₃N₄ nucleation. This procedure allows variation in the fineness of the matrix as well as in the number and dimension of the large elongated β-Si₃N₄ grains embedded in the matrix. Since identical green bodies are used as starting material, the resulting microstructure can easily be tailored toward corresponding application needs.     

Microstructure control and mechanical properties of porous silicon nitride ceramics

Porous silicon nitride ceramics with a fibrous interlocking microstructure were synthesized by carbothermal nitridation of silicon dioxide. The influences of different starting powders on microstructure and mechanical properties of the samples were studied. The results showed that the microstructure and mechanical properties of porous silicon nitride ceramics depended mostly on the size of starting powders. The formation of single-phase β-Si₃N₄ and the microstructure of the samples were demonstrated by XRD and SEM, respectively. The resultant porous Si₃N₄ ceramics with a porosity of 71% showed a relative higher flexural strength of 24 MPa.     

Effect of lattice defects on the thermal conductivity of β-Si3N4

Two types of β-Si₃N₄ were sintered at 1900 °C one for 8 h and the other for 36 h by using Yb₂O₃ and ZrO₂ as sintering additives. The latter specimen was further annealed at 1700 °C for 100 h to promote grain growth. The microstructures of the sintered materials were investigated by SEM, TEM, and EDS. The thermal conductivities of the specimens were 110 and 150 Wm⁻¹K⁻¹, respectively. The sintered material which possessed 110 Wm⁻¹K⁻¹ had numerous small precipitates that consisted of Yb, O and N elements and internal dislocations in the β-Si₃N₄ grains. In the sintered material with 150 Wm⁻¹K⁻¹ neither precipitates nor dislocations were observed in the grains. The microscopic evidence indicates that the improvement in the thermal conductivity of the β-Si₃N₄ was attributable to the reduction of internal defects of the β-Si₃N₄ grains with sintering and annealing time as the grains grew.     

Micro scale fracture strength of grains and grain boundaries in polycrystalline La-doped β-Si3N4 ceramics

Micro scale fracture strength of grains and grain boundaries in polycrystalline La-doped β-Si₃N₄ ceramics were investigated and compared with theoretically predicted values. The fracture behaviour of SiO₂-La₂O₃ intergranular glassy phase (IGP) between β-Si₃N₄ grains was modelled by ab initio simulations. Microcantilevers were FIB-milled both from polycrystalline regions and single grains of β-Si₃N₄ and were tested in bending using a nanoindenter. The fracture strength of β-Si₃N₄ grains which fractured at fixing was 10.6 ± 0.8 GPa while the strength of the beams that failed at defects was 5.9 ± 2.3 GPa. Polycrystalline β-Si₃N₄ samples showed intergranular fracture with decreasing strength values in the range of 2.9 ± 0.4 – 2.1 ± 0.5 GPa. The comparison of single grain results with theoretical values in the literature revealed a correlation between theoretical and experimental results, which was used to convert our ab initio simulations from subnano to micro size samples. The converted strength for IGP showed quantitative agreement with micro-bending experiments.     

Porous Si3N4/SiC Ceramics Prepared via Nitridation of Si Powder with SiC Addition

Porous Si₃N₄/SiC ceramics with high porosity were prepared via nitridation of Si powder, using SiC as the second phase and Y₂O₃ as sintering additive. With increasing SiC addition, porous Si₃N₄/SiC ceramics showed high porosity, low flexural strength, and decreased grain size. However, the sample with 20wt% SiC addition showed highest flexural strength and lowest porosity. Porous Si₃N₄/SiC ceramics with a porosity of 36–45% and a flexural strength of 107‐46MPa were obtained. The linear shrinkage of all porous Si₃N₄/SiC ceramics is below 0.42%. This study reveals that the nitridation route is a promising way to prepare porous Si₃N₄/SiC ceramics with favorable flexural strength, high porosity, and low linear shrinkage.     

Effect of SiO2 content on the microstructure,mechanical and dielectric properties of Si3N4 ceramics

This study investigated the effect of SiO₂ content in the Y₂O₃–Al₂O₃ additive system on the microstructure, mechanical and dielectric properties of silicon nitride (Si₃N₄) ceramics. The total sintering additive content was fixed at 8 wt% and the amount of SiO₂ was varied from 0 to 7 wt%. The crystalline phases of the samples were determined by X-ray diffraction analysis. Complete α-to-β transformation of the Si₃N₄ occurred during sintering of all of the samples, which indicated that the phase transformation was unaffected by the SiO₂ content. However, the microstructures showed that the aspect ratio of the β-Si₃N₄ grains decreased and the residual porosity increased with increasing SiO₂ content. Additionally, the flexural strength and the dielectric constant decreased with increasing SiO₂ content because of the residual porosity and the formation of the Si₂N₂O phase via a reaction of SiO₂ with Si₃N₄.