Catalytic performance of a novel ceramic-supported vanadium oxide catalyst for NO reduction with NH3

A novel TiO₂/Al₂O₃/cordierite honeycomb-supported V₂O₅–MoO₃–WO₃ monolithic catalyst was studied for the selective reduction of NO with NH₃. The effects of reaction temperature, space velocity, NH₃/NO ratio and oxygen content on SCR activity were evaluated. Two other V₂O₅–MoO₃–WO₃ monolithic catalysts supported on Al₂O₃/cordierite honeycomb or TiO₂/cordierite honeycomb support, two types of pellet catalysts supported on TiO₂/Al₂O₃ or Al₂O₃, as well as three types of pellet catalysts V₂O₅–MoO₃–WO₃–Al₂O₃ and V₂O₅–MoO₃–WO₃–TiO₂ were tested for comparison. The experiment results show that this catalyst has a higher catalytic activity for SCR with comparison to others. The results of characterization show, the preparation method of this catalyst can give rise to a higher BET surface area and pore volume, which is strongly related with the highly active performance of this catalyst. At the same time, the function of the combined carrier of TiO₂/Al₂O₃ cannot be excluded.     

Catalytic synthesis of methanethiol from hydrogen sulfide and carbon monoxide over vanadium-based catalysts

The direct synthesis of methanethiol, CH₃SH, from CO and H₂S was investigated using sulfided vanadium catalysts based on TiO₂ and Al₂O₃. These catalysts yield high activity and selectivity to methanethiol at an optimized temperature of 615 K. Carbonyl sulfide and hydrogen are predominant products below 615 K, whereas above this temperature methane becomes the preferred product. Methanethiol is formed by hydrogenation of COS, via surface thioformic acid and methylthiolate intermediates. Water produced in this reaction step is rapidly converted into CO₂ and H₂S by COS hydrolysis.

Titania was found to be a good catalyst for methanethiol formation. The effect of vanadium addition was to increase CO and H₂S conversion at the expense of methanethiol selectivity. High activities and selectivities to methanethiol were obtained using a sulfided vanadium catalyst supported on Al₂O₃. The TiO₂, V₂O₅/TiO₂ and V₂O₅/Al₂O₃ catalysts have been characterized by temperature programmed sulfidation (TPS). TPS profiles suggest a role of V₂O₅ in the sulfur exchange reactions taking place in the reaction network of H₂S and CO.     

Parameters influencing the synergetic effect induced by vanadium incorporation on non-conventional (Al)(Ga)PO supports for the propane ammoxidation

A series of V-oxide supported catalysts (5V/AlPO₄, 5V/Al_0.5Ga_0.5PO₄, 5V/GaPO₄) were prepared in order to study their catalytic behaviour in the ammoxidation of propane. Catalysts were characterized by BET surface area, XRD, Raman spectroscopy, TPR-H₂ and XPS. The presence of vanadium induced the crystallization of the supports (AlPO₄, Al_0.5Ga_0.5PO₄ and GaPO₄). Crystalline V₂O₅ was observed on the V-based catalysts. Catalytic results showed that the impregnation of vanadium enhances the propane conversion and selectivity to acrylonitrile (ACN). At 530 °C 5V/Al_0.5Ga_0.5PO₄ exhibits the highest selectivity to ACN. One assumes that the best performance of 5V/Al_0.5Ga_0.5PO₄ in propane ammoxidation, is due to on the one hand the easiest reduction of V₂O₅ on Al_0.5Ga_0.5PO₄ and to on the other hand a certain tunability of the reduced species stabilized on Al_0.5Ga_0.5PO₄.     

Factors controlling the selectivity of V2O5 supported catalysts in the oxidative dehydrogenation of propane

The surface properties of a series of V₂O₅ catalysts supported on different oxides (Al₂O₃, H–Na/Y zeolite, MgO, SiO₂, TiO₂ and ZrO₂) were investigated by transmission electron microscopy and FTIR spectroscopy augmented by CO and NH₃ adsorption. In the case of the V₂O₅/SiO₂ system TEM images evidenced the presence of V₂O₅ crystallites, whereas such segregated phase was not observed for the other samples. VO_x species resulted widely spread on the surface of Al₂O₃, H–Na/Y zeolite, MgO and SiO₂, whereas on TiO₂ and ZrO₂ they are assembled in a layer covering almost completely the support. Furthermore, evidences for the presence in this layer of V–OH Brønsted acid sites close to the active centres were found. It is proposed that propene molecules primarily produced by oxydehydrogenation of propane can be adsorbed on this acid centres and then undergo an overoxidation by reaction with redox centres in the neighbourhood. This features could account for the low selectivity of V₂O₅/TiO₂ and V₂O₅/ZrO₂ catalysts.     

Hydrodesulfurization of dibenzothiophenes over molybdenum catalyst supported on TiO2–Al2O3

Composite types of TiO₂–Al₂O₃ supports, which are γ-aluminas coated by titania, have been prepared by chemical vapor deposition (CVD), using TiCl₄ as a precursor. Then supported molybdenum catalysts have been prepared by an impregnation method. As supports, we employed γ-alumina, anatase types of titania, and composite types of TiO₂–Al₂O₃ with different loadings of TiO₂. We studied the conversion of Mo from oxidic to sulfidic state through sulfurization by X-ray photoelectron spectroscopy (XPS). The obtained spectra unambiguously revealed the higher reducibility from oxidic to sulfidic molybdenum species on the TiO₂ and TiO₂–Al₂O₃ supports compared to that on the Al₂O₃ support. Higher TiO₂ loadings of the TiO₂–Al₂O₃ composite support led to higher reducibility for molybdenum species. Furthermore, the catalytic behavior of supported molybdenum catalysts has been investigated for hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the TiO₂–Al₂O₃ supported Mo catalysts, in particular for the 4,6-dimethyl-DBT, is much higher than that obtained over Al₂O₃ supported Mo catalyst. The ratio of the corresponding cyclohexylbenzene (CHB)/biphenyl (BP) derivatives is increased over the Mo/TiO₂–Al₂O₃. This indicates that the prehydrogenation of an aromatic ring plays an important role in the HDS of DBT derivatives over TiO₂–Al₂O₃ supported catalysts.     

Fischer–Tropsch synthesis over Re-promoted Co supported on Al2O3, SiO2 and TiO2: Effect of water

The activity and selectivity of rhenium promoted cobalt Fischer–Tropsch catalysts supported on Al₂O₃, TiO₂ and SiO₂ have been studied in a fixed-bed reactor at 483 K and 20 bar. Exposure of the catalysts to water added to the feed deactivates the Al₂O₃ supported catalyst, while the activity of the TiO₂ and SiO₂ supported catalysts increased. However, at high concentrations of water both the SiO₂ and TiO₂ supported catalyst deactivated. Common for all catalysts was an increase in C₅₊ selectivity and a decrease in the CH₄ selectivity by increasing the water partial pressure. The catalysts have been characterized by scanning transmission electron microscope (STEM), BET, H₂ chemisorption and X-ray diffraction (XRD).     

The structures of VOx/MOx and alkali-VOx/MOx catalysts and their catalytic performances for soot combustion

Vanadium oxides supported on γ-Al₂O₃, SiO₂, TiO₂, and ZrO₂ were studied on their molecular structures and reactive performances for soot combustion. To investigate the effect of different alkali metals on the structures and reactivities of supported-vanadium oxide catalysts, they were doped into the V₄/TiO₂ catalyst which had the best intrinsic activity for soot combustion in the selected supported vanadium oxide catalysts. The experimental results demonstrated that the catalytic properties of these catalysts depended on the vanadium loading amount, support nature, and the presence or the absence of alkali metals. The spectroscopic analysis (FT-IR and UV–vis) and H₂-TPR results revealed that the higher activity of alkali-promoted vanadium oxide catalysts could be related to the ability of alkali metal promoting the redox cycle of the active vanadyl species. TG results showed that adding alkali to V_m/TiO₂ catalyst was beneficial to lowering their melting points. Low melting points could ensure the good surface atom migration ability, which would improve the contact between the catalyst and soot. Due to the alkali metal components promoting the redox ability and the mobility of the catalysts, alkali-modified vanadium oxide catalysts could remarkably improve their catalytic activities for soot combustion. The catalytic activity order for soot combustion followed Li > Na > K > Rb > Cs in the catalyst system of alkali-V₄/TiO₂, and the reason why it followed this sequence was discussed.     

Molecular structure–reactivity relationships for the oxidation of sulfur dioxide over supported metal oxide catalysts

The catalytic oxidation of sulfur dioxide to sulfur trioxide over several binary (M_xO_y/TiO₂) and ternary (V₂O₅/M_XO_Y/TiO₂) supported metal oxide catalysts was systematically investigated. The supported metal oxide components were essentially 100% dispersed as surface metal oxide species, as confirmed by Raman spectroscopy characterization. The sulfur dioxide oxidation turnover frequencies of the binary catalysts were all within an order of magnitude (V₂O₅/TiO₂>Fe₂O₃/TiO₂>Re₂O₇/TiO₂  CrO₃/TiO₂  Nb₂O₅/TiO₂>MoO₃/TiO₂  WO₃/TiO₂). An exception was the K₂O/TiO₂ catalysts, which is essentially inactive for sulfur dioxide oxidation. With the exception of K₂O, all of the surface metal oxide species present in the ternary catalysts (i.e., oxides of V, Fe, Re, Cr, Nb, Mo and W) can undergo redox cycles and oxidize SO₂ to SO₃. The turnover frequency for sulfur dioxide oxidation over all of these catalysts is approximately the same at both low and high surface coverages. This indicates that the mechanism of sulfur dioxide oxidation is not sensitive to the coordination of the surface metal oxide species. A comparison of the activities of the ternary catalysts with the corresponding binary catalysts suggests that the surface vanadium oxide and the additive surface metal oxide redox sites act independently without synergistic interactions. The V₂O₅/K₂O/TiO₂ catalyst showed a dramatic reduction in the catalytic activity in comparison to the unpromoted V₂O₅/TiO₂ catalyst. The ability of K₂O to significantly retard the redox potential of the surface vanadia species is primarily responsible for the lower catalytic activity of the ternary catalytic system. The fundamental insights generated from this research can potentially assist in the molecular design of the air pollution control catalysts: (1) the development of catalysts for low temperature oxidation of SO₂ to SO₃ during sulfuric acid manufacture (2) the design of efficient SCR DeNO_x catalysts with minimal SO₂ oxidation activity and (3) improvements in additives for the simultaneous oxidation/sorption of sulfur oxides in petroleum refinery operations.     

Molecular structure and reactivity of the Group V metal oxides

The physical, electronic and reactivity properties of bulk and supported Group V metal oxides (V, Nb, Ta and Db) were compared at the molecular level. Dubnium is a very short-lived element, 60 s, whose properties have not been extensively studied, but can be predicted from knowledge of the other members of the Group V metal oxides. Bulk V₂O₅ possesses platelet morphology with the active surface sites only located at the edges: primarily surface redox sites and some surface acidic sites. Bulk Nb₂O₅ and Ta₂O₅, as well as to be expected for bulk Db₂O₅, possess isotropic morphologies and the active surface sites relatively homogeneously dispersed over their surfaces: only surface acidic sites. However, the bifunctional bulk V₂O₅ was found to exhibit a much higher specific acidic catalytic activity than the acidic bulk Nb₂O₅ and Ta₂O₅, the latter being almost identical in their specific acidic catalytic activity. The bulk properties of the Group V metal oxides were essentially transferred to the analogous supported Group V metal oxides, where the active Group V metal oxides were present as a two-dimensional monolayer on various oxide supports (e.g., Al₂O₃, TiO₂, ZrO₂ as well as Nb₂O₅ and Ta₂O₅). For supported vanadia catalysts, the active surface sites were essentially redox sites, with the exception of supported V₂O₅/Al₂O₃ that also contained strong acidic sites. For supported niobia and tantala catalysts, as well as to be expected for supported dubnia catalysts, the active surface sites were exclusively acidic sites. However, the TOF_redox for the supported vanadia catalysts and the TOF_acidic for the supported niobia and tantala catalysts varied over several orders of magnitude as a function of the specific oxide support with the electronegativity of the oxide support cation. However, the TOF_redox varied inversely to that of the TOF_acidic variation because of the opposite requirements of these active surface sites. Surface redox sites are enhanced by reduction and surface acidic sites are enhanced by stabilization (lack of reduction). The current fundamental understanding of the Group V metal oxides allows for the molecular engineering of their metal oxide applied catalytic materials.     

Oxidative desulfurization of synthetic diesel using supported catalysts: Part II. Effect of oxidant and nitrogen-compounds on extraction–oxidation process

Oxidative desulfurization (ODS) of a synthetic diesel was carried out at mild conditions (atmospheric pressure and 60 °C) in presence of V₂O₅/Al₂O₃ and V₂O₅/TiO₂ catalysts. Two main aspects were studied: the effect of the oxidant reagent and the presence of nitrogen compounds on ODS of benzothiophenic compounds prevailing in diesel, such as benzothiophene, dibenzothiophene and alkyl substituted in positions 4 and 6. Results show that activity is improved when using hydrogen peroxide, as oxidant reagent, and V₂O₅/Al₂O₃, as catalyst. This result was attributed to the high decomposition of peroxide due to the presence of catalyst. In presence of nitrogen compounds, the ODS activity decreases in the order: quinoline > indole > carbazole. In order to explain this effect, successive chemisorption of DBT and quinoline on V₂O₅/Al₂O₃ catalyst was evaluated by FT-IR, and the results show that DBT is displaced by quinoline, occupying the adsorption sites of catalyst. N-compound effect could be explained by strong adsorption of nitrogen compounds on catalytic sites.     

Thermal behaviour, redox properties, and catalytic performance of alkali-promoted V2O5 catalysts in the selective oxidation of p-methoxytoluene: a comparative study

Alkali-promoted V₂O₅ catalysts M–V₂O₅ (M=Li, K, Cs) were synthesised by impregnation of V₂O₅ with alkali sulphate solution. Pure V₂O₅ was used for comparison. X-ray diffraction, spectroscopic (FTIR), and thermoanalytical methods (STA/MS) have been used to characterise the phase composition, the adsorption properties, and the reducibility of the catalysts. The catalytic performance was proved using the oxidation of p-methoxytoluene (PMT) to p-methoxybenzaldehyde (PMBA) as test reaction. The surface acidity is lowered, but the reducibility is enhanced with increasing size and basic properties of the alkali cation. This leads to an increased adduct (PMT) adsorption and decreased product (PMBA) adsorption in the order V₂O₅2O₅K–V₂O₅2O₅. Consequently, the catalytic performance is improved in the same way. The formation of bronze phases at relative low temperatures in the case of K– and Cs–V₂O₅ stabilise V⁴⁺ oxidation state and improve the redox properties and consequently the catalytic results. The admixture of the non-reactive pyridine enhances the aldehyde selectivity by further lowering of the surface acidity. Additionally, pyridinium cations generated during catalytic reaction and incorporated into the formed alkali bronze phases stabilise these structures.     

SO2 resistant antimony promoted V2O5/TiO2 catalyst for NH3-SCR of NOx at low temperatures

To get the low temperature sulfur resistant V₂O₅/TiO₂ catalysts quantum chemical calculation study was carried out. After selecting suitable promoters (Se, Sb, Cu, S, B, Bi, Pb and P), respective metal promoted V₂O₅/TiO₂ catalysts were prepared by impregnation method and characterized by X-ray diffraction (XRD) and Brunner Emmett Teller surface area (BET-SA). Se, Sb, Cu, S promoted V₂O₅/TiO₂ catalysts showed high catalytic activity for NH₃ selective catalytic reduction (NH₃-SCR) of NO_x carried at temperatures between 150 and 400 °C. The conversion efficiency followed in the order of Se > Sb > S > V₂O₅/TiO₂ > Cu but Se was excluded because of its high vapor pressure. An optimal 2 wt% ‘Sb’ loading was found over V₂O₅/TiO₂ for maximum NO_x conversion, which also showed high resistance to SO₂ in presence of water when compared to other metal promoters. In situ electrical conductivity measurement was carried out for Sb(2%)/V₂O₅/TiO₂ and compared with commercial W(10%)V₂O₅/TiO₂ catalyst. High electrical conductivity difference (ΔG) for Sb(2%)/V₂O₅/TiO₂ catalyst with temperature was observed. SO₂ deactivation experiments were carried out for Sb(2%)/V₂O₅/TiO₂ and W(10%)/V₂O₅/TiO₂ at a temperature of 230 °C for 90 h, resulted Sb(2%)/V₂O₅/TiO₂ was efficient catalyst. BET-SA, X-ray photoelectron spectroscopy (XPS) and carbon, hydrogen, nitrogen and sulfur (CHNS) elemental analysis of spent catalysts well proved the presence of high ammonium sulfate salts over W(10%)/V₂O₅/TiO₂ than Sb(2%)/V₂O₅/TiO₂ catalyst.     

制备方法对V_2O_5-WO_3/TiO_2选择性催化还原催化剂性能的影响

采用共沉淀法、溶胶-凝胶法和浸渍法制备了V2O5质量分数4%和WO3质量分数6%的V2O5-WO3/TiO2选择性催化还原催化剂,对比了3种方法制备的催化剂选择性催化还原NO性能。采用X射线衍射、热重、N2吸附-脱附和程序升温还原等对制备的V2O5-WO3/Ti O2催化剂的结构和性质进行表征,结果表明,共沉淀法制备的V2O5-WO3/TiO2催化剂具有更好的选择性催化还原NO活性和更大的比表面积,影响共沉淀法选择性催化还原NO活性的主要因素是催化剂的热稳定性、表面羟基数量、比表面积、粒径分布以及V、W与Ti之间的内在作用。     

Development of new catalysts for deep hydrodesulfurization of gas oil

TiO₂–Al₂O₃ composite supports have been prepared by chemical vapor deposition (CVD) over γ-Al₂O₃ substrate, using TiCl₄ as the precursor. High dispersion of TiO₂ overlayer on the surface of Al₂O₃ has been obtained, and no cluster formation has been detected. The catalytic behavior of Mo supported on Al₂O₃, TiO₂ and TiO₂–Al₂O₃ composite has been investigated for the hydrodesulfurization (HDS) of dibenzothiophene (DBT) and methyl-substituted DBT derivatives. The conversion over the Mo catalysts supported on TiO₂–Al₂O₃ composite, in particular for the HDS of 4,6-dimethyldibenzothiophene (4,6-DMDBT) is much higher than that of conversion obtained over Mo catalyst supported on Al₂O₃. The ratio of the corresponding cyclohexylbenzenes/biphenyls is increased over Mo catalyst supported on TiO₂–Al₂O₃ composite support. This means that the reaction rate of prehydrogenation of an aromatic ring rather than the rate of hydrogenolysis of C–S bond cleavage is accelerated for the HDS of DBT derivatives. The Mo/TiO₂–Al₂O₃ catalyst leads to higher catalytic performance for deep HDS of gas oil.     

Selective catalytic reduction of nitric oxide by propane over vanadia-titania aerogels

An investigation has been carried out of the effect of vanadia loading on the activity and selectivity ofV₂O₅TiO₂ aerogel catalysts, prepared by a two-step procedure, for the reduction of NO by propane. The structure of catalysts have been characterized by laser Raman spectroscopy and XRD measurements. At vanadia loading levels below ca. 4.4 wt%, the vanadia is present in the form of coordinated polymeric species, whereas crystallites of V₂O₅ are formed at higher vanadia contents. At this critical level of 4.4 wt% V₂O₅, the kinetic measurements showed also a maximum in the activity per mass of catalyst which very likely indicated that the coordinated polymeric surface species are more active than crystalline V₂O₅. The selectivity towards the formation of dinitrogen decreased as the loading increased, presumably because of the formation of larger polymeric species and V₂O₅ crystallites, below and above the critical loading level, respectively. For the reduction of NO by propane, titania supported vanadia aerogel catalysts are significantly more active, per mass of catalyst, and more selective towards N₂ formation than conventionalV₂O₅TiO₂ and V₂O₅Al₂O₃ aerogel catalysts, at vanadia loading levels below ca. 11 wt%.     

溶胶-凝胶原位合成宽活性温度V2O5/TiO2脱硝催化剂

利用溶胶-凝胶技术原位合成一系列不同V₂O₅担载量的V₂O₅/TiO₂催化剂,通过BET、XRD、NH₃-TPD及紫外-可见光等手段对催化剂进行表征。结果表明：制备的催化剂均具有介孔结构,V₂O₅在TiO₂表面高度分散,且存在3种典型的酸性位。通过选择性催化还原反应对V₂O₅/TiO₂催化剂进行活性评价,结果显示随着V₂O₅含量的增加,NO转化率大于75%的温度窗口向低温方向偏移,含10% （质量分数）V₂O₅的催化剂的NO转化率为80%的温度窗口最宽为200～450℃,240℃时20 h连续实验表现出稳定的抗硫抗水性能。结合紫外-可见光谱分析,揭示了钒掺杂所形成的单聚和低聚钒酸盐为催化剂的活性组分。     

催化剂上丙烷氧化脱氢制丙烯

以浸渍法制备VMo/γ-Al₂O₃和VMoMg/γ-Al₂O₃催化剂,考察其催化丙烷氧化脱氢制丙烯的反应活性,采用XRD、UV-Vis DRS和In suit IR对催化剂进行表征。结果表明,V负载质量分数为3%、Mo负载质量分数为7%时的3V7Mo/γ-Al₂O₃催化剂表现出较好的催化性能;添加Mg后催化剂的催化性能有所改善,反应温度500 ℃时,丙烷转化率为18.19%,丙烯选择性74.76%。丙烷和丙烯在3V7Mo/γ-Al₂O₃和3V₇Mo₄Mg/γ-Al₂O₃催化剂上吸附后,C—H键的H与催化剂活性中心的晶格氧发生作用形成H—O键,且3V₇Mo₄Mg/γ-Al₂O₃催化剂上出现C—O键的温度比3V₇Mo/γ-Al₂O₃催化剂高,表明加入Mg有利于提高丙烯选择性。     

TiO2-coated on Al2O3 support prepared by the CVD method for HDS catalysts

Mo---Co or Mo---Ni catalysts supported on alumina (Al₂O₃) have been widely used for hydrodesulfurization (HDS) of heavy petroleum fractions. In order to enhance the catalytic activities for HDS, a composite type support (TiO₂-Al₂O₃) prepared by the chemical vapor deposition (CVD) method has been studied. We found that Mo catalyst supported on TiO₂-Al₂O₃ showed much higher catalytic activity for HDS of dibenzothiophene derivatives than the catalysts supported on Al₂O₃.     

Selective oxidation of hydrogen sulfide containing excess water and ammonia over vanadia–titania aerogel catalysts

A series of V₂O₅–TiO₂ aerogel catalysts were prepared by sol–gel method with subsequent supercritical drying with CO₂. The aerogel catalysts showed much higher surface areas and total pore volumes than V₂O₅–TiO₂ xerogel and impregnated V₂O₅–TiO₂ catalysts. Two species of surface vanadium in the aerogel catalysts were identified by Raman measurements: monomeric vanadyl and polymeric vanadates. The selective oxidation of hydrogen sulfide in the presence of excess water and ammonia was studied over these catalysts. Aerogel catalysts showed very high conversion of H₂S without harmful emission of SO₂. Temperature programmed reduction (TPR), XRD and Raman analyses revealed that the high catalytic performance of the aerogel catalysts originated from their highly dispersed VO_x species and high reducibility.     

Photocatalytic degradation of 4-nitrophenol in aqueous suspension by using polycrystalline TiO2 samples impregnated with Cu(II)-phthalocyanine

A number of supported metal oxide catalysts were screened for their catalytic performance for the oxidation of carbon black (CB; a model diesel soot) using NO₂ as the main oxidant. It was found that contact between the carbon and catalyst was a key factor in determining the rate of oxidation by NO₂. Oxides with low melting points, such as Re₂O₇, MoO₃ and V₂O₅ showed higher activities than did Fe₃O₄ and Co₃O₄. The activities of MoO₃ and V₂O₅ on various supporting materials were also examined. MoO₃/SiO₂ was the most active catalyst among the supported MoO₃ examined, whereas, V₂O₅/MCM-41 showed the highest activity among the supported V₂O₅. Different performances of the supported MoO₃ catalysts were explained by the interaction of MoO₃ with the supports: a strong MoO₃/support interaction may result in a poor mobility of MoO₃ and a poor activity for oxidation of carbon by NO₂. The high activity of V₂O₅/MCM-41 was associated with its catalysis of the oxidation of SO₂ by NO₂ to form SO₃, which substantially promotes oxidation of carbon by NO₂. Addition of transition metal oxides or sulfates to supported MoO₃ and V₂O₅ was also investigated. Combining MoO₃ or V₂O₅ with CuO on SiO₂, adding VOSO₄ to MoO₃/SiO₂ or MoO₃/Al₂O₃ and adding TiOSO₄ or CuSO₄ to V₂O₅/Al₂O₃ improved the catalytic performance.