The origin of N2O formation in the selective catalytic reduction of NOx by NH3 in O2 rich atmosphere on Cu-faujasite catalysts

The selective catalytic reduction (SCR) of NO_x (NO + NO₂) by NH₃ in O₂ rich atmosphere has been studied on Cu-FAU catalysts with Cu nominal exchange degree from 25 to 195%. NO₂ promotes the NO conversion at NO/NO₂ = 1 and low Cu content. This is in agreement with next-nearest-neighbor (NNN) Cu ions as the most active sites and with N_xO_y adsorbed species formed between NO and NO₂ as a key intermediate. Special attention was paid to the origin of N₂O formation. CuO aggregates form 40–50% of N₂O at ca. 550 K and become inactive for the SCR above 650 K. NNN Cu ions located within the sodalite cages are active for N₂O formation above 600 K. This formation is greatly enhanced when NO₂ is present in the feed, and originated from the interaction between NO (or NO₂) and NH₃. The introduction of selected co-cations, e.g. Ba, reduces very significantly this N₂O formation.     

Co3O4 based catalysts for NO oxidation and NOx reduction in fast SCR process

Reaction activities of several developed catalysts for NO oxidation and NO_x (NO + NO₂) reduction have been determined in a fixed bed differential reactor. Among all the catalysts tested, Co₃O₄ based catalysts are the most active ones for both NO oxidation and NO_x reduction reactions even at high space velocity (SV) and low temperature in the fast selective catalytic reduction (SCR) process. Over Co₃O₄ catalyst, the effects of calcination temperatures, SO₂ concentration, optimum SV for 50% conversion of NO to NO₂ were determined. Also, Co₃O₄ based catalysts (Co₃O₄-WO₃) exhibit significantly higher conversion than all the developed DeNO_x catalysts (supported/unsupported) having maximum conversion of NO_x even at lower temperature and higher SV since the mixed oxide Co-W nanocomposite is formed. In case of the fast SCR, N₂O formation over Co₃O₄-WO₃ catalyst is far less than that over the other catalysts but the standard SCR produces high concentration of N₂O over all the catalysts. The effect of SO₂ concentration on NO_x reduction is found to be almost negligible may be due to the presence of WO₃ that resists SO₂ oxidation.     

Catalytic oxidation of HCN over a 0.5% Pt/Al2O3 catalyst

The adsorption of HCN on, its catalytic oxidation with 6% O₂ over 0.5% Pt/Al₂O₃, and the subsequent oxidation of strongly bound chemisorbed species upon heating were investigated. The observed N-containing products were N₂O, NO and NO₂, and some residual adsorbed N-containing species were oxidized to NO and NO₂ during subsequent temperature programmed oxidation. Because N-atom balance could not be obtained after accounting for the quantities of each of these product species, we propose that N₂ and was formed. Both the HCN conversion and the selectivity towards different N-containing products depend strongly on the reaction temperature and the composition of the reactant gas mixture. In particular, total HCN conversion reaches 95% above 250 °C. Furthermore, the temperature of maximum HCN conversion to N₂O is located between 200 and 250 °C, while raising the reaction temperature increases the proportion of NO_x in the products. The co-feeding of H₂O and C₃H₆ had little, if any effect on the total HCN conversion, but C₃H₆ addition did increase the conversion to NO and decrease the conversion to NO₂, perhaps due to the competing presence of adsorbed fragments of reductive C₃H₆. Evidence is also presented that introduction of NO and NO₂ into the reactant gas mixture resulted in additional reaction pathways between these NO_x species and HCN that provide for lean-NO_x reduction coincident with HCN oxidation.     

Influence of CO2 and H2O on NOx storage and reduction on a Pt–Ba/γ-Al2O3 catalyst

In this paper, the effect of CO₂ and H₂O on NO_x storage and reduction over a Pt–Ba/γ-Al₂O₃ (1 wt.% Pt and 30 wt.% Ba) catalyst is shown. The experimental results reveal that in the presence of CO₂ and H₂O, NO_x is stored on BaCO₃ sites only. Moreover, H₂O inhibits the NO oxidation capability of the catalyst and no NO₂ formation is observed. Only 16% of the total barium is utilized in NO storage. The rich phase shows 95% selectivity towards N₂ as well as complete regeneration of stored NO. In the presence of CO₂, NO is oxidized into NO₂ and more NO_x is stored as in the presence of H₂O, resulting in 30% barium utilization. Bulk barium sites are inactive in NO_x trapping in the presence of CO₂·NH₃ formation is seen in the rich phase and the selectivity towards N₂ is 83%. Ba(NO₃)₂ is always completely regenerated during the subsequent rich phase. In the absence of CO₂ and H₂O, both surface and bulk barium sites are active in NO_x storage. As lean/rich cycling proceeds, the selectivity towards N₂ in the rich phase decreases from 82% to 47% and the N balance for successive lean/rich cycles shows incomplete regeneration of the catalyst. This incomplete regeneration along with a 40% decrease in the Pt dispersion and BET surface area, explains the observed decrease in NO_x storage.     

NO reduction by CH4 over Pd/Co-sulfated zirconia catalysts

A series of sulfated zirconia supported Pd/Co catalysts was synthesized by the sol–gel method and examined for NO_x reduction by methane. The NO conversion increased up to a Co/S ratio of 0.43, and then decreased at a higher Co loading (Co/S = 0.95). Sulfate content was also essential for obtaining high selectivity to molecular nitrogen. A catalyst loaded with 0.06 wt.% Pd, 2.1 wt.% Co and 2.1 wt.% S (Pd/Co-SZ-2) exhibited remarkable performance under lean conditions and displayed stability in a long-term durability test using a synthetic reaction mixture containing 10% water vapor. This catalyst exhibited the highest sulfur retention most probably as cobalt sulfide. Besides, the catalytic oxidation of NO to NO_y groups was confirmed by FT-IR, in agreement with the general mechanism for the SCR of NO by hydrocarbons. In the absence of oxygen in the feed stream, the catalyst was highly active for NO reduction with methane. IR stretching bands assigned to N₂O and adsorbed nitro groups were identified upon adsorbing NO on Pd/Co-SZ-2. This indicates that under rich conditions disproportionation of NO to N₂O and NO₂ occurs and confirms that the formation of NO₂ species is an essential step for NO reduction by CH₄.     

SCR of NOx with CH3OH on H-mordenite: mechanism and reaction intermediates

The selective reduction of NO_x over H-mordenite (H-m) was studied using CH₃OH as reducing agent. Results are compared with those obtained with other conventional reducing agents (ethylene and methane), with gas-phase reactions, and with other metal-exchanged mordenites (Cu-mordenite (Cu-m) and Co-mordenite (Co-m)). H-m was found to be an effective catalyst for the SCR of NO_x with CH₃OH. When different reducing agents were compared over H-m, CH₃OH > C₂H₄ > CH₄ was the order according to the maximum NO conversion obtained using 1% of oxygen in the feed. Instead, if selectivity is considered, the order results CH₄ > CH₃OH > C₂H₄. In reaction experiments, two distinct zones defined by two maxima with NO to N₂ conversion are obtained at two different temperatures. A correlation exists between the said zones and the CO : CO₂ ratio. At low temperatures, CO prevails whereas at high temperatures CO₂ prevails. These results indicate that there exist different reaction intermediates. Evidence from reaction experiments, FTIR results, and transient experiments suggest that the reaction mechanism involves formaldehyde and dimethyl ether (DME) as intermediates in the 200–500°C temperature range. The surface interaction between CH₃OH (or its decomposition products) and NO is negligible if compared with NO₂, indicating that the oxidation of NO to NO₂ on acid sites is a fundamental path in this system. Different from other non-oxygenated reductants (methane and ethylene), a gas-phase NO_x initiation effect on hydrocarbon combustion was not observed.     

Alumina- and titania-based monolithic catalysts for low temperature selective catalytic reduction of nitrogen oxides

The selective catalytic reduction of NO+NO₂ (NO_x) at low temperature (180–230°C) with ammonia has been investigated with copper-nickel and vanadium oxides supported on titania and alumina monoliths. The influence of the operating temperature, as well as NH₃/NO_x and NO/NO₂ inlet ratios has been studied. High NO_x conversions were obtained at operating conditions similar to those used in industrial scale units with all the catalysts. Reaction temperature, ammonia and nitrogen dioxide inlet concentration increased the N₂O formation with the copper-nickel catalysts, while no increase was observed with the vanadium catalysts. The vanadium-titania catalyst exhibited the highest DeNO_x activity, with no detectable ammonia slip and a low N₂O formation when NH₃/NO_x inlet ratio was kept below 0.8. TPR results of this catalyst with NO/NH₃/O₂, NO₂/NH₃/O₂ and NO/NO₂/NH₃/O₂ feed mixtures indicated that the presence of NO₂ as the only nitrogen oxide increases the quantity of adsorbed species, which seem to be responsible for N₂O formation. When NO was also present, N₂O formation was not observed.     

Selective catalytic reduction of NO and NO2 at low temperatures

The fast SCR reaction using equimolar amounts of NO and NO₂ is a powerful means to enhance the NO_x conversion over a given SCR catalyst. NO₂ fractions in excess of 50% of total NO_x should be avoided because the reaction with NO₂ only is slower than the standard SCR reaction.

At temperatures below 200 °C, due to its negative temperature coefficient, the ammonium nitrate reaction gets increasingly important. Half of each NH₃ and NO₂ react to form dinitrogen and water in analogy to a typical SCR reaction. The other half of NH₃ and NO₂ form ammonium nitrate in close analogy to a NO_x storage-reduction catalyst. Ammonium nitrate tends to deposit in solid or liquid form in the pores of the catalyst and this will lead to its temporary deactivation.

The various reactions have been studied experimentally in the temperature range 150–450 °C for various NO₂/NO_x ratios. The fate of the deposited ammonium nitrate during a later reheating of the catalyst has also been investigated. In the absence of NO, the thermal decomposition yields mainly ammonia and nitric acid. If NO is present, its reaction with nitric acid on the catalyst will cause the formation of NO₂.     

The effect of hydrogen on the selective catalytic reduction of NO in excess oxygen over Ag/Al2O3

The selective catalytic reduction (SCR) of nitrogen oxides (NO_x) by propane in the presence of H₂ on sol–gel prepared Ag/Al₂O₃ catalysts (0.5–5 wt.% Ag) was investigated. It was confirmed that hydrocarbon-assisted SCR of NO_x is remarkably enhanced by co-feeding hydrogen to a lean exhaust gas mixture (λ>1), attaining considerable activity within a wide temperature window (470–825 K). The samples had marginal activity at 575 K without co-fed H₂, but achieved up to 60% NO_x conversion in the presence of H₂ at a space velocity of 30,000 h⁻¹. NO₂ as NO_x feed component is not converted to N₂ by C₃H₈ to a substantial extent under lean conditions. This points to an activation route of NO through direct conversion to adsorbed nitrite/nitrate or to a dissociation of NO over Ag⁰, formed through short-term reduction by H₂. The nature of Ag species was characterized by X-ray diffraction, temperature-programmed reduction, pulse thermoanalytical measurements, electron microscopy and FTIR spectroscopy. It could be shown that Ag₂O nano-sized clusters are predominantly present on all samples, whereas formation of silver aluminate could not be confirmed. Nano-sized Ag₂O clusters can reversibly be reduced/reoxidized by H₂. A silver loading higher than 2 wt.% leads to a part of Ag₂O particles, which are thermally decomposed during calcination at 800 K or higher. The catalytic role of this metallic silver is still unclear. Formal kinetic analysis of catalytic data revealed that the activation energy of the overall reaction is significantly lowered in the presence of H₂. The presence of water does not change the activation energy. It is concluded that hydrogen reduces the nano-sized Ag₂O clusters to Ag⁰ on a short-term scale. Zero-valent silver promotes a dissociation pathway of NO_x conversion. The fact that more oxidized ad-species (nitrite/nitrate) are observed in the presence of H₂ is attributed to a dissociative activation of gas-phase oxygen on Ag⁰.     

Reactivity of NO/NO2–NH3 SCR system for diesel exhaust aftertreatment: Identification of the reaction network as a function of temperature and NO2 feed content

We present a systematic study of the NH₃-SCR reactivity over a commercial V₂O₅–WO₃/TiO₂ catalyst in a wide range of temperatures and NO/NO₂ feed ratios, which cover (and exceed) those of interest for industrial applications to the aftertreatment of exhaust gases from diesel vehicles. The experiments confirm that the best deNO_x efficiency is achieved with a 1/1 NO/NO₂ feed ratio. The main reactions prevailing at the different operating conditions have been identified, and an overall reaction scheme is herein proposed.

Particular attention has been paid to the role of ammonium nitrate, which forms rapidly at low temperatures and with excess NO₂, determining a lower N₂ selectivity of the deNO_x process. Data are presented which show that the chemistry of the NO/NO₂–NH₃ reacting system can be fully interpreted according to a mechanism which involves: (i) dimerization/disproportion of NO₂ and reaction with NH₃ and water to give ammonium nitrite and ammonium nitrate; (ii) reduction of ammonium nitrate by NO to ammonium nitrite; (iii) decomposition of ammonium nitrite to nitrogen. Such a scheme explains the peculiar deNO_x reactivity at low temperature in the presence of NO₂, the optimal stoichiometry (NO/NO₂ = 1/1), and the observed selectivities to all the major N-containing products (N₂, NH₄NO₃, HNO₃, N₂O). It also provides the basis for the development of a mechanistic kinetic model of the NO/NO₂–NH₃ SCR reacting system.     

Analysis of the structural parameters controlling the temperature window of the process of SCR-NOx by low paraffins over metal-exchanged zeolites

Catalytic activity of H- and FeH-ferrierite (FER) zeolites with iron content from 50 to 4000 ppm in NO–NO₂ equilibration and SCR of NO_x by propane was measured, both in NO₂-poor and NO₂-rich streams. The activity of FeH-FER in SCR in NO₂-poor streams depends strongly on the Fe content; this relationship is valid down to traces of iron, while no such correlation was indicated in NO₂-rich streams. This was rationalized by realizing the negligible activity of zeolite protons for NO–NO₂ equilibration. Accordingly the SCR activity of H-FER in NO₂-poor streams necessitates presence of iron traces. In the NO₂–O₂–propane mixtures a process in absence of zeolite catalyst initiating propane oxidation and NO₂→NO conversion, but without N₂ formation, was evidenced at temperatures over 350 °C. It is suggested that such a radical process participate in characteristic narrow temperature window for NO_x reduction by propane.     

The bifunctional reaction pathway and dual kinetic regimes in NOx SCR by methane over cobalt mordenite catalysts

The pathway for selective reduction of NO_x by methane over Co mordenite cataysts has been studied by comparing the rates of the individual reactions (NO oxidation, CH₄ oxidation, NO₂ reduction) with that of the combined reaction (NO + O₂ + CH₄). Co⁽⁺²⁾ was exchanged into H-MOR and Na-MOR to give catalysts with different metal loading and number of support protons. Additionally, exchanged Co⁽⁺²⁾ ions were precipitated with NaOH to produce dispersed cobalt oxide on Na-MOR. The NO oxidation rate is the same for ion exchanged Co⁽⁺²⁾ ions in H-MOR and Na-MOR, but the rate of Co⁽⁺²⁾ ions is much lower than that of cobalt oxide. NO oxidation equilibrium is obtained only for those catalysts with high metal loading, cobalt oxide or run at low GHSV. Under the conditions of selective catalytic reduction, methane oxidation by O₂ is low for all catalysts. The turnover frequency of Co on Na-MOR, however, is higher than that on H-MOR. The rate of NO₂ reduction to N₂ is directly proportional to the number of support acid sites and independent of the amount of Co. Comparison of the rates and selectivities for the individual reactions with the combined reaction of NO + O₂ + CH₄ indicates that there are two types of catalysts. For the first, the NO oxidation is in equilibrium and the rate determining step is reduction of NO₂. For these catalysts, the rate (and selectivity) for formation of N₂ is identical from NO + O₂ + CH₄ and NO₂ + CH₄. These catalysts have high metal loading and few acid sites. Nevertheless, the rate of N₂ formation increases with increasing number of protons. For the second type of catalyst, NO oxidation is not in equilibrium and is the rate limiting step. For these catalysts the rate of N₂ formation increases with increasing metal loading. Neither catalyst type, however, is optimized for the maximum formation of N₂. By using a mixture of catalysts, one with high NO oxidation activity and one with a large number of Brønsted acid sites, the rate of N₂ is greater than the weighted sum of the individual catalysts. The current results support the proposal that the pathway for selective catalytic reduction is bifunctional where metal sites affect NO oxidation, while support protons catalyze the formation of N₂.     

A combination of NOx trapping materials and urea-SCR catalysts for use in the removal of NOx from mobile diesel engines

Preliminary studies on a series of nanocomposite BaO–Fe ZSM-5 materials have been carried out to determine the feasibility of combining NO_x trapping and SCR-NH₃ reactions to develop a system that might be applicable to reducing NO_x emissions from diesel-powered vehicles. The materials are analysed for SCR-NH₃ and SCR-urea reactivity, their NO_x trapping and NH₃ trapping capacities are probed using temperature programmed desorption (TPD) and the activities of the catalysts for promoting the NH_{3 ads} + NO/O₂ → N₂ and NO_{x ads} + NH₃ → N₂ reactions are studied using temperature programmed surface reaction (TPSR).     

Transient analysis of the release and reduction of NOx using a Pt/Ba/Al2O3 catalyst

The release and reduction of NO_x in a NO_x storage-reduction (NSR) catalyst were studied with a transient reaction analysis in the millisecond range, which was made possible by the combination of pulsed injection of gases and time resolved time-of-flight mass spectrometry. After an O₂ pulse and a subsequent NO pulse were injected into a pellet of the Pt/Ba/Al₂O₃ catalyst, the time profiles of several gas products, NO, N₂, NH₃ and H₂O, were obtained as a result of the release and reduction of NO_x caused by H₂ injection. Comparing the time profiles in another analysis, which were obtained using a model catalyst consisting of a flat 5 nmPt/Ba(NO₃)₂/cordierite plate, the release and reduction of NO_x on Pt/Ba/Al₂O₃ catalyst that stored NO_x took the following two steps; in the first step NO molecules were released from Ba and in the second step the released NO was reduced into N₂ by H₂ pulse injection. When this H₂ pulse was injected in a large amount, NO was reduced to NH₃ instead of N₂.

A only small amount of H₂O was detected because of the strong affinity for alumina support. We can analyze the NO_x regeneration process to separate two steps of the NO_x release and reduction by a detailed analysis of the time profiles using a two-step reaction model. From the result of the analysis, it is found that the rate constant for NO_x release increased as temperature increase.     

Improvement in selective catalytic reduction of nitrogen oxides by using dielectric barrier discharge

The behavior of the selective catalytic reduction of nitrogen oxides (NO_x) assisted by a dielectric barrier discharge was investigated. The principal function of the dielectric barrier discharge in the present system is to generate ozone, which is continuously fed to a chamber where the ozone and NO-rich exhaust gas (NO forms the large majority of NO_x) are mixed. In the ozonization chamber, a part of NO contained in the exhaust gas is oxidized to NO₂, and then the mixture of NO and NO₂ enters the catalytic reactor. The ozonization method proposed in this study was found to be more energy-efficient for the oxidation of NO to NO₂ than the typical nonthermal plasma process. The degree of NO oxidation was approximately equal to the amount of ozone added to the exhaust gas, implying that the decomposition of ozone into molecular oxygen was relatively slow, compared to its reaction with NO. When the exhaust gas was first treated by ozone to produce a mixture of NO and NO₂, a remarkable enhancement in the catalytic reduction of nitrogen oxides was observed. Neither NO₃ nor N₂O₅ was formed in the present system, but small amounts of ozone and N₂O (less than 5 ppm) were detected in the outlet gas.     

Nitrous oxide formation in low temperature selective catalytic reduction of nitrogen oxides with V2O5/TiO2 catalysts

Nitric oxide and nitric dioxide compounds (NO_x) present in stack gases from nitric acid plants are usually eliminated by selective catalytic reduction (SCR) with ammonia. In this process, small quantities of nitrous oxide (N₂O) are produced. This undesirable molecule has a high greenhouse gas potential and a long lifetime in the atmosphere, where it can contribute to stratospheric ozone depletion. The influence of catalyst composition and some operating variables were evaluated in terms of N₂O formation, using V₂O₅/TiO₂ catalysts. High vanadia catalyst loading, nitric oxide inlet concentration and reaction temperature increase the generation of this undesirable compound. The results suggest that adsorbed ammonia not only reacts with NO via SCR, but also with small quantities of oxygen activated by the presence of NO. The mechanism proposed for N₂O generation at low temperature is based on the formation of surface V–ON species which may be produced by the partial oxidation of dissociatively adsorbed ammonia species with NO + O₂ (eventually NO₂). When these active sites are in close proximity they can interact to form an N₂O molecule. This mechanism seems to be affected by changes in the active site density produced by increasing the catalyst vanadia loading.     

The removal of NOx from a lean exhaust gas using storage and reduction on H3PW12O40·6H2O

NO_x sorption and reduction capacities of 12-tungstophosphoric acid hexahydrate (H₃PW₁₂O₄₀·6H₂O, HPW) were measured under representative alternating conditions of lean and rich exhaust-type gas mixture. Under lean conditions, the sorption of NO_x is large and is equivalent to 37 mg of NO_x/g_HPW. Although a part of these NO_x remains unreduced, HPW is able to reduce some of the NO_x to produce N₂ by a reaction between the sorbed NO₂ and hydrocarbon (HC), but this process is slow. The addition of 1% Pt affects strongly the chemical behaviour occurring during the course of a rich operation. The NO desorption observed at the beginning of the rich phase is strongly accelerated. The direct correlation between NO₂ consumption and CO₂ production shows that the principal pathway is the reaction CO+NO₂→CO₂+NO. In a mixture of reducing gas (CO, HC, H₂), the competition is strongly in favour of CO though in its absence the reaction observed was the hydrogenation of propene to propane.     

DeNOx reactions on Cu-zeolites Decomposition of NO, N2O and SCR of NO by C3H8 and CH4 on Cu-ZSM-5 and Cu-AlTS-1 catalysts

Cu-ZSM-5 and Cu-AlTS-1 catalysts were prepared by solid state ion exchange and studied in DeNO_x reactions. A NO₃ type surface complex was found to be an active intermediate in the decomposition of NO and N₂O. Copper was oxidized to Cu²⁺ in the decomposition reactions. Oscillations at full N₂O conversion were observed in the gas phase O₂ concentration, without any change in the N₂ concentration. The oscillation was synchronized by gas phase NO formed from the NO₃ complex. The same complex seems to be an active intermediate also in NO selective catalytic reduction (SCR) by methane, whereas carbonaceous deposits play a role in NO SCR by propane. TPD reveals that only 10–20% of the total copper in the zeolites participates in the catalytic cycles.     

Effect of Pt on the water resistance of Co-zeolites upon the SCR of NOx with CH4

The objective of this work was to study the promotional effect of Pt on Co-zeolite (viz. mordenite, ferrierite, ZSM-5 and Y-zeolite) and Co/Al₂O₃ on the selective catalytic reduction (SCR) of NO_x with CH₄ under dry and wet reaction stream. After being reduced in H₂ at 350°C, the PtCo bimetallic zeolites showed higher NO to N₂ conversion and selectivity than the monometallic samples, as well as a combination of the latter samples such as mechanical mixtures or two-stage catalysts. After the same pretreatment, under wet reaction stream, the bimetallic samples were also more active. Among the other catalysts studied with 5% of water in the feed, (NO = CH₄ = 1000 ppm, O₂ = 2%), the NO conversion dropped to zero over Co_2.0Mor at 500°C and GHSV = 30,000 h⁻¹, whereas it is 20% in Pt_0.5Co_2.0Mor. In Pt/Co/Al₂O₃ the NO_x conversion dropped below 5% with only 2% of water under the same reaction conditions. The specific activity given as molecules of NO converted per total metal atom per second were 16.5 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Fer, 13 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0Mor, 4.33 × 10⁻⁴ s⁻¹ for Pt_0.5Co_2.0ZSM-5 and 0.5 × 10⁻⁴ s⁻¹ for Pt/Co/Al₂O₃. The Y-zeolite-based samples were inactive in both mono and bimetallic samples. The species initially present in the solid were Pt° and Co°, together with Co²⁺ and Pt²⁺ at exchange positions. Co° seems not to participate as an active site in the SCR of NO_x. Those species remained after the reaction but some reorganization occurred. A synergetic effect among the different species that enhances both the NO to NO₂ reaction, the activation of CH₄ and also the ability of the catalyst to adsorb NO, could be responsible for the high activity and selectivity of the bimetallic zeolites.     

重型柴油机主要含氮化合物的排放特性

采用傅里叶变换红外光谱(FTIR)技术,研究了加装选择性催化还原SCR装置的重型柴油机主要含氮化合物排放,重点探索了不同工况下主要含氮化合物NO、NO₂和N₂O的排放特性。结果表明:未加装SCR的原机,随负荷的增加,柴油机NO排放持续上升,NO₂排放先升后降,N₂O排放很少。加装SCR后该柴油机NO与NO₂排放均明显下降,标定转速下NO₂排放降幅较大,主要是其NO₂/NO值稍高导致快速SCR反应较多的原因。由于存在SCR副反应,与原机相比,柴油机N₂O排放比原机平均增加2倍以上,最大转矩转速下N₂O排放升幅更高。N₂O排放随负荷的增加而上升,主要是排温升高导致NH₃氧化生成N₂O反应速率增加的原因。加装SCR后,该机排气中的NO/NO_x值要明显低于原机状态,而外特性的NO₂/NO_x值和N₂O/NO_x值高达12.8%和20.7%,均远高于原机的3.0%和0.5%。