Effect of the tacticity of poly(methyl methacrylate) on the phase diagram of its ternary blends

Previously, isotactic and atactic poly(methyl methacrylates) (PMMAs) were found to be miscible with poly(vinyl phenol) (PVPh) and poly(hydroxy ether of bisphenol‐A) (phenoxy) because all the prepared films were transparent and showed composition‐dependent glass transition temperatures (T_g's). However, syndiotactic PMMA was immiscible with PVPh because most of the cast films had two T_g's. On the contrary, syndiotactic PMMA was still miscible with phenoxy. According to our preliminary results, PVPh and phenoxy are not miscible. Also to our knowledge, nobody has reported any results concerning the effect of the tacticity of PMMA on its ternary blend containing PVPh and phenoxy. The miscibility of a ternary blend consisting of PVPh, phenoxy, and tactic PMMA was thus investigated and reported in this article. Calorimetry was used as the principal tool to study miscibility. An approximate phase diagram of the ternary blends containing different tactic PMMA was established, probably for the first time, based on differential scanning calorimetry data. Immiscibility was found in most of the studied ternaries but a slight difference due to the effect of tacticity of PMMA was definitely observed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 2720–2726, 2002     

Thermal decomposition behavior of γ‐irradiated poly(vinyl acetate)/poly(methyl methacrylate) miscible blends

Miscible polymer blends based on various ratios of poly(vinyl acetate) (PVAc) and poly(methyl methacrylate) (PMMA) were prepared in film form by the solution casting technique using benzene as a common solvent. The thermal decomposition behavior of these blends and their individual homopolymers before and after γ‐irradiation at various doses (50–250 kGy) was investigated. The thermogravimetric analysis technique was utilized to determine the temperatures at which the maximum value of the rate of reaction (T_max) occurs and the kinetic parameters of the thermal decomposition. The rate of reaction curves of the individual homopolymers or their blends before or after γ‐ irradiation displayed similar trends in which the T_max corresponding to all polymers was found to exist in the same position but with different values. These findings and the visual observations of the blend solutions and the transparency of the films gave support to the complete miscibility of these blends. Three transitions were observed along the reaction rate versus temperature curves; the first was around 100–200°C with no defined T_max, which may arise from the evaporation of the solvent. The second T_max was in the 340–380°C range, which depended on the polymer blend and the γ‐irradiation condition. A third transition was seen in the rate of reaction curves only for pure PVAc and its blends with PMMA with ratios up to 50%, regardless of γ‐ irradiation. We concluded that γ‐irradiation improved the thermal stability of PVAc/PMMA blends, even though the PMMA polymer was degradable by γ irradiation. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 99: 1773–1780, 2006     

Phase behavior and properties of poly(methyl methacrylate)/poly(vinyl acetate) blends prepared via in situ polymerization

Polymer blends composed of poly(methyl methacrylate) (PMMA) and poly(vinyl acetate) (PVAc) were prepared via radical-initiated polymerization of methyl methacrylate (MMA) in the presence of PVAc. Differential scanning calorimetry and dynamic mechanical analysis were employed to investigate the miscibility and phase behavior of the blends. The PMMA/PVAc blends of in situ polymerization were found to be phase separated and exhibited a two-phase structure, although some chain transferring reaction between the components occurred. The phase separation resulted from the solvent effect of MMA during the in situ polymerization, which was confirmed by the investigation of phase behavior based on solution cast blending. Solubility analysis of the polymerized blends indicated that some chain transferring reaction between the components occurred during the polymerization. An abrupt increase in gel content from 21.2 to 72.4 wt % was observed when the inclusion of PVAc increased from 30 to 40 wt %, and the gel component consisted of the component polymers as shown by infrared spectroscopy studies. The thermogravimetric analysis study indicated that the inclusion of a small amount of PVAc gives rise to a marked stabilization effect on the thermal stability. The PMMA/PVAc blends exhibited increased notched impact properties with the inclusion of 5 wt % PVAc. © 1998 John Wiley & Sons, Inc. J Appl Polym Sci 69: 675–684, 1998     

Study of the solvent effect on miscibility between poly(vinyl chloride) and poly(methyl methacrylate) in the solution state – viscometric measurements

In this work, the solvent effect on the miscibility between poly(vinyl chloride) (PVC) and poly(methyl methacrylate) (PMMA) in ternary polymer solutions was examined by the viscometric method. In these systems, we could understand that the used solvents, tetrahydrofuran (THF) or N,N‐dimethylformamide (DMF), mainly affect the interaction between PVC and PMMA, while prompting various miscible properties. In PVC/PMMA/THF solution, THF is a near θ‐solvent and a poor solvent for PVC and PMMA, respectively. The mixing of the tighter PMMA coils and more extended PVC coils in THF may cause the sea–island heterogeneous structure below the weight fraction of PMMA in the polymer mixture w_PMMA = 0.7, resulting in immiscible PVC/PMMA mixtures. At w_PMMA ≥ 0.7, the PVC/PMMA mixtures are relatively miscible, giving homogeneous polymer solutions. It means that the miscibility between PVC and PMMA depends on the composition of polymer mixture. However, due to the similar affinity of DMF to PVC and PMMA, PVC/PMMA/DMF solutions exhibit high miscibility between PVC and PMMA at about w_PMMA = 0.5. © 2000 Society of Chemical Industry     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl pyrrolidone)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMA) (designated iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(vinyl pyrrolidone) (PVP) primarily in chloroform to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PVP. The aPMMA/PVP and sPMMA/PVP blends were found to be miscible because all the prepared films showed composition-dependent glass-transition temperatures (T_g). The glass-transition temperatures of the aPMMA/PVP blends are equal to or lower than weight average and can be qualitatively described by the Gordon–Taylor equation. The glass-transition temperatures of the other miscible blends (i.e., sPMMA/PVP blends) are mostly higher than weight average and can be approximately fitted by the simplified Kwei equation. The iPMMA/PVP blends were found to be immiscible or partially miscible based on the observation of two glass-transition temperatures. The immiscibility is probably attributable to a stronger interaction among isotactic MMA segments because its ordination and molecular packing contribute to form a rigid domain. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 3190–3197, 2001     

Effect of tacticity of poly(methyl methacrylate) on the miscibility with poly(styrene‐co‐acrylonitrile)

Isotactic, atactic, and syndiotactic poly(methyl methacrylates) (PMMAs) (designated as iPMMA, aPMMA, and sPMMA) with approximately the same molecular weight were mixed separately with poly(styrene‐co‐acrylonitrile) (abbreviated as PSAN) containing 25 wt % of acrylonitrile in tetrahydrofuran to make three polymer blend systems. Differential scanning calorimetry (DSC) was used to study the miscibility of these blends. The results showed that the tacticity of PMMA has a definite impact on its miscibility with PSAN. The aPMMA/PSAN and sPMMA/PSAN blends were found to be miscible because all the prepared films were transparent and showed composition dependent glass transition temperatures (T_gs). The glass transition temperatures of the two miscible blends were fitted well by the Fox equation, and no broadening of the glass transition regions was observed. The iPMMA/PSAN blends were found to be immiscible, because most of the cast films were translucent and had two glass transition temperatures. Through the use of a simple binary interaction model, the following comments can be drawn. The isotactic MMA segments seemed to interact differently with styrene and with acrylonitrile segments from atactic or syndiotactic MMA segments. © 1999 John Wiley & Sons, Inc. J Appl Polym Sci 74: 2894–2899, 1999     

Influence of the tacticity of poly(methyl methacrylate) on the miscibility with poly(vinyl chloride)

It can be concluded from the work of Schurer et al.¹⁰ that poly(vinyl chloride) (PVC) is more miscible with syndiotactic than with isotactic poly(methyl methacrylate) (PMMA). By choosing different molar masses for the various tactic forms of PMMA it is possible to obtain blends with PVC with similar phase behaviour, i.e. in all cases a cloud-point curve with a minimum in the vicinity of 190°C. In this way a more quantitative statement about the influence of the tacticity of PMMA on its miscibility with PVC can be made. One of the principal differences between syndiotactic or atactic PMMA and isotactic PMMA is the higher flexibility of the latter. Using Flory's equation of state theory it will be shown that the effect of this difference is large enough to explain the difference in phase behaviour observed. Heats of mixing of low molar mass analogues were also measured and found to be negative.     

Miscibility enhancement on the poly(vinylchloride)/poly(methylmethacrylate) blend and characterization by inverse gas chromatography: The corrected polymer–polymer interaction parameters from the probes dependency

The miscibility of poly(vinyl chloride)/poly(methylmethacrylate) (PVC/PMMA) system was improved by introducing some pyrrolidone units into the main chains of PMMA. For that purpose, we have synthesized two copolymers of poly(methylmethacrylate‐co‐vinylpyrrolidone) (MMVP) through a radical polymerization and carried out a comparative study of PVC/MMVP blends by inverse gas chromatography (IGC) and differential scanning calorimetry (DSC) methods. The adequacy of seven n‐alkane probes has been tested to determine the thermodynamic parameters. The miscibility of the two systems has been proved by a single T_g for each blend. This observation was also confirmed by DSC analysis. To highlight the presence of interaction and its intensity between PVC and MMVP in the blends, the polymer–polymer interaction parameters have been evaluated by IGC trough which the influence of the solute has been resolved. The Schneider approach confirmed the miscibility of these systems as the K deviates positively from unity. The miscibility has been appeared highlighted from the positive difference in surface energy between the pure polymers and their blends. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effect of in situ polymerization conditions of methyl methacrylate on the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene)‐g‐styrene) PMMA/AES Blends

In this study, the structural and morphological properties of poly(methyl methacrylate)/poly(acrylonitrile‐g‐(ethylene‐co‐propylene‐co‐diene‐g‐styrene) (PMMA‐AES) blends were investigated with emphasis on the influence of the in situ polymerization conditions of methyl methacrylate. PMMA‐AES blends were obtained by in situ polymerization, varying the solvent (chloroform or toluene) and polymerization conditions: method A—no stirring and air atmosphere; method B—stirring and N₂ atmosphere. The blends were characterized by infrared spectroscopy (FTIR), transmission electron microscopy (TEM), and dynamic mechanical analysis (DMA). The results showed that the PMMA‐AES blends are immiscible and present complex morphologies. This morphology shows an elastomeric dispersed phase in a glassy matrix, with inclusion of the matrix in the elastomer domains, suggesting core shell or salami morphology. The occlusion of the glassy phase within the elastomeric domains can be due to the formation of graft copolymer and/or phase inversion during polymerization. However, this morphology is affected by the polymerization conditions (stirring and air or N₂ atmosphere) and by the solvent used. The selective extraction of the blends' components and infrared spectroscopy showed that crosslinked and/or grafting reactions occur on the elastomer chains during MMA polymerization. The glass transition of the elastomer phase is influenced by morphology, crosslinking, and grafting degree and, therefore, T_g depends on the polymerization conditions. On the other hand, the behavior of T_g of the glassy phase with blend composition suggests miscibility or partial miscibility for the SAN phase of AES and PMMA. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate)/poly(vinyl acetate) blends

The miscibility and crystallization behavior of poly(3‐hydroxybutyrate‐co‐3‐hydroxyvalerate) (P(HB‐co‐HV))/poly(vinyl acetate) (PVAc) blends have been investigated by differential scanning calorimetry (DSC) and polarized optical microscopy (POM). It was found that P(HB‐co‐HV)/PVAc blends were miscible in the melt over the whole compositions. Thus the blend exhibited a single glass transition temperature (T_g), which increased with increasing PVAc composition. The spherulitic morphologies of P(HB‐co‐HV)/PVAc blends indicated that the PVAc was predominantly segregated into P(HB‐co‐HV) interlamellar or interfibrillar regions during P(HB‐co‐HV) crystallization because of the volume‐filled spherulites. As to the crystallization kinetics study, it was found that the overall crystallization and crystal growth rates decreased with the addition of PVAc. The kinetics retardation was primarily attributed to the reduction of chain mobility and dilution of P(HB‐co‐HV) upon mixing with higher T_g PVAc. The overall crystallization rate was predominantly governed by the spherulitic growth rate and promoted by the samples treated with the quenched state because of the higher nucleation density. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 980–988, 2006     

Gas chromatographic determination of the interaction parameter of poly(ethylene oxide)/poly(methyl methacrylate) blends

Inverse gas chromatography (IGC) has been used to investigate thermodynamic miscibility of a molten poly(ethylene oxide) (PEO)/poly(methyl methacrylate) (PMMA) blend. Toluene, benzene, and chloroform have been employed as probes in pure and mixed stationary phases of these polymers. Experimental measurements have been taken over a narrow range of temperatures because of the high PMMA glass transition temperature as well as the degradation of the PEO. The interaction parameter χ₂₃ determined at 150°C is slightly negative and dependent on the interacting probe, as has been also noted in previous chromatographic studies on polymer-polymer miscibility. The last section is devoted to a model calculation, using Flory's equation of state theory. Different χ₂₃-concentration curves have been simulated, with the interaction energy parameter X₂₃ as an adjustable parameter.     

Crystallization behavior and hydrophilicity of poly(vinylidene fluoride)/poly(methyl methacrylate)/poly(vinyl pyrrolidone) ternary blends

Ternary blends composed of matrix polymer poly(vinylidene fluoride) (PVDF) with different proportions of poly(methyl methacrylate) (PMMA)/poly(vinyl pyrrolidone) (PVP) blends were prepared by melt mixing. The miscibility, crystallization behavior, mechanical properties and hydrophilicity of the ternary blends have been investigated. The high compatibility of PVDF/PMMA/PVP ternary blends is induced by strong interactions between the carbonyl groups of the PMMA/PVP blend and the CF₂ or CH₂ group of PVDF. According to the Fourier transform infrared and wide‐angle X‐ray difffraction analyses, the introduction of PMMA does not change the crystalline state (i.e. α phase) of PVDF. By contrast, the addition of PVP in the blends favors the transformation of the crystalline state of PVDF from non‐polar α to polar β phase. Moreover, the crystallinity of the PVDF/PMMA/PVP ternary blends also decreases compared with neat PVDF. Through mechanical analysis, the elongation at break of the blends significantly increases to more than six times that of neat PVDF. This confirms that the addition of the PMMA/PVP blend enhances the toughness of PVDF. Besides, the hydrophilicity of PVDF is remarkably improved by blending with PMMA/PVP; in particular when the content of PVP reaches 30 wt%, the water contact angle displays its lowest value which decreased from 91.4° to 51.0°. Copyright © 2011 Society of Chemical Industry     

Miscibility of C60‐containing poly(methyl methacrylate)/poly(vinylidene fluoride) blends

The miscibility of C₆₀‐containing poly(methyl methacrylate) (PMMA‐C₆₀) with poly(vinylidene fluoride) (PVDF) was studied. Two PMMA‐C₆₀ samples containing 2.6 and 7.4 wt % C₆₀ were found to be miscible with PVDF based on single glass transition temperature criterion and melting point depression of PVDF. However, the interaction parameters of the two blend systems are less negative than that of the PMMA/PVDF blend system, showing that the incorporation of C₆₀ reduces the ability of carbonyl groups of PMMA to interact with PVDF. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 1393–1396, 2000     

Molecular modelling of poly(methylidene malonate 2.1.2) using a continuum solvation approach

Molecular modelling studies have been undertaken to investigate the properties of poly(methylidene malonate 2.1.2). The influence of several factors has been evaluated: the size effect with three degrees of polymerization (n = 5, 20 and 40), the role of the solvent (polar and apolar) with an implicit solvation treatment, the influence of the degree of erosion, and the role of the tacticity. Estimations of the lipophilicity of oligomers have been obtained by Monte Carlo studies followed by molecular lipophilic potential calculations on the molecular surfaces of the conformers. Then, using molecular dynamics with an implicit treatment of solvent, the shape of the polymers was studied. The results are in good agreement with experimental solubility information and new data about the potential role of the tacticity have been obtained. © 1999 Society of Chemical Industry     

Studies on the miscibility and phase structure in blends of poly(epichlorohydrin) and poly(vinyl acetate)

The miscibility of atactic poly(epichlorohydrin) (aPECH) with poly(vinyl acetate) (PVAc) was examined under two different conditions: (i) in dilute solution, using vicometeric measurements and (ii) as cast films, using differential scanning calorimetric (DSC) and FT-infrared spectroscopy. Phase separation on heating, i.e. lower critical solution temperature (LCST) behavior of the aPECH/PVAc blends was examined by the measurement of transmitted light intensity against temperature. From viscosity measurements, the Krigbaum-Wall polymer-polymer interaction (ΔB) was evaluated. The DSC results show that the aPECH/PVAc blends are miscible as evidenced by the observation of a single composition-dependent glass-transition temperature (T_g) which is well described by the Couchman and Gordon Taylor models. The Flory-Huggins interaction parameter (χ₁₂) calculated from the T_g-method was negative and equal to −0.01, indicating a relatively low interaction strength. The FT-IR results match very well with those of DSC. The cloud point phenomenon is thermodynamically driven but phase separation, once taken place, is diffusion controlled in normal accessible time.     

Solvent effects on the miscibility of poly(methyl methacrylate)/poly(bisphenol a carbonate) blends

Blends of atactic or syndiotactic poly(methyl methacrylate) (designated as aPMMA or sPMMA) and poly(bisphenol A carbonate) (PC) were prepared from solution casting. Tetrahydrofuran (THF) and chloroform were used as solvent. Experimental results indicated that the as‐cast blends from THF were quite different from the chloroform‐cast ones. After film preparation, THF‐cast blends did not show any visible phase separation. However, chloroform‐cast blends formed a phase‐separated structure. The as‐cast PC from either solvent was not completely amorphous, and had a melting point at 239–242°C, indicating a certain degree of crystallinity. In contrast, the quenched samples of aPMMA/PC blends prepared from the two solvents behaved virtually the same. They both showed aPMMA dissolves better in PC, but PC solubility in aPMMA is very little. Using sPMMA instead of aPMMA to blend with PC, different results were obtained. The quenched sPMMA/PC blends cast from THF showed only one T_g. However, immiscibility (i.e., two T_gs) was found in the same blend system when cast from chloroform. THF was believed to cause the observation of single T_g due to the following kinetic reason. sPMMA and PC were still trapped together even after THF removal in a homogeneous, but nonequilibrium state below the glass transition. Therefore, the quenched sPMMA/PC blends were not truly thermodynamically miscible. From the results of aPMMA or sPMMA with PC, increasing syndiotacticity seemed to improve the miscibility between PMMA and PC. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 2842–2850, 2001     

Synthesis and characterization of poly(pyridylurea) and poly(pyridylthiourea), potentially semiconducting polymers

Poly(pyridylureas) and poly(pyridylthioureas) were synthesized by reacting 2,6‐diaminopyridine with phosgene and thiophosgene, respectively, using THF and pyridine as solvent. The synthesized polymers were characterized by IR‐spectroscopy, elemental analysis, and X‐ray photoelectron spectroscopy. Thermal stability of the polymers was determined by thermal degradation between 35°C and 700°C. The 50% weight loss of polypyridylureas was above 400°C while for the polypyridylthioureas it was above 450°C. Undoped poly(pyridylureas) and poly(pyridylthioureas) behave as semiconductors, σ = 10^?9 (Ω cm)^?1. After doping with I₂ and SbF₅, the electrical conductivity increases several orders of magnitude, σ = 10^?7(Ω cm)^?1. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Thermal and dynamic mechanical behavior of bionanocomposites: Fumed silica nanoparticles dispersed in poly(vinyl pyrrolidone), chitosan,and poly(vinyl alcohol)

Various bionanocomposites were prepared by dispersing fumed silica (SiO₂) nanoparticles in biocompatible polymers like poly(vinyl pyrrolidone) (PVP), chitosan (Chi), or poly(vinyl alcohol) (PVA). For the bionanocomposites preparation, a solvent evaporation method was followed. SEM micrographs verified fine dispersion of silica nanoparticles in all used polymer matrices of composites with low silica content. Sufficient interactions between the functional groups of the polymers and the surface hydroxyl groups of SiO₂ were revealed by FTIR measurements. These interactions favored fine dispersion of silica. Mechanical properties such as tensile strength and Young's modulus substantially increased with increasing the silica content in the bionanocomposites. Thermogravimetric analysis (TGA) showed that the polymer matrices were stabilized against thermal decomposition with the addition of fumed silica due to shielding effect, because for all bionanocomposites the temperature, corresponding to the maximum decomposition rate, progressively shifted to higher values with increasing the silica content. Finally, dynamic thermomechanical analysis (DMA) tests showed that for Chi/SiO₂ and PVA/SiO₂ nanocomposites the temperature of β‐relaxation observed in tanδ curves, corresponding to the glass transition temperature T_g, shifted to higher values with increasing the SiO₂ content. This fact indicates that because of the reported interactions, a nanoparticle/matrix interphase was formed in the surroundings of the filler, where the macromolecules showed limited segmental mobility. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Enzymatic degradation of poly(D,L‐lactide) and its blends with poly(vinyl acetate)

The enzymatic degradation of poly(D ,L ‐lactide) (PLA) was investigated using two different lipases, Novozym 435 and Lipolase. The optimum temperature was 50°C for the enzymatic degradation of PLA. The effect of various solvents on the degradation of PLA was investigated at 50°C using Novozym 435, and toluene was found to be the best solvent among the solvents investigated. The enzymatic degradation of the blends of PLA and PVAc was investigated at 50°C in toluene. The enzymatic degradation of the blends of PLA and PVAc showed that there is an interaction between the polymers during degradation, which results in the reduction of degradation rate of both polymers in the blend. A continuous distribution model was used to determine the rate coefficients for polymer degradation. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 657–680 2006     

Casting solvent effect on crystallization behavior of poly(vinyl acetate)/poly(ethylene oxide) blends: DSC study

Poly(vinyl acetate) (PVAc)/poly(ethylene oxide) (PEO) blends were prepared by casting from either benzene or chloroform. The solvent effects on the crystallization behavior and thermodynamic properties of the blends were studied by the differential scanning calorimeter (DSC). Two grades of PEO with different molecular weights (PEO200 with M_w = 200,000 g/mol and PEO2 with M_n = 2000 g/mol) were used in this work. The thermal analysis revealed that the blends cast from either benzene or chloroform were miscible in the molten state. The crystallization of PEO in the benzene-cast blends was more easily suppressed than it was in the chloroform-cast blends. Furthermore, the benzene-cast blends showed a greater negative value of Flory-Huggins interaction parameter than those cast from chloroform in the PVAc/PEO200 poly-blend system. It was supposed that the benzene-cast blends had more homogeneous morphology. © 1997 John Wiley & Sons, Inc. J Appl Polym Sci 64: 411–421, 1997