共查询到20条相似文献,搜索用时 109 毫秒
1.
苯与1-十二烯烷基化反应的研究进展 总被引:2,自引:0,他引:2
介绍了苯与1-十二烯烷基化反应制备直链烷基苯(LAB)的国内生产近况,讨论了固体酸催化剂催化苯与1-十二烯烷基化反应的研究情况,分析了离子液体催化苯与1-十二烯烷基化反应的研究进展,同时,对苯与1-十二烯烷基化反应的研发趋势提出了展望。 相似文献
2.
用盐酸三乙胺和无水三氯化铝合成了不同配比的Et_3NHCl-xAlCl_3离子液体,研究了离子液体的组成、反应时间、反应温度、苯与离子液体的摩尔比、苯与1-十二烯摩尔比对苯与1-十二烯烷基化反应的影响。结果表明,Et_3NHCl-xAlCl_3酸性离子液体具有较高的催化活性,良好的低温反应活性和2位异构体选择性.通过正交试验,得到了优化的离子液体组成和反应条件为AlCl_3与Et_3NHCl的摩尔比1.4,反应温度10℃,苯与离子液体的摩尔比42,苯与1-十二烯摩尔比25。该条件下,1-十二烯的转化率为100%,2-苯基十二烷的选择性为42.5%. 相似文献
3.
4.
对USY分子筛进行HF改性实验。XRD表征结果表明,改性后的催化剂基本保持了原有USY分子筛的晶型结构,并且分子筛与HF间部分发生作用,使催化性能得到改善。以苯和十二碳烯为原料,经烷基化反应合成十二烷基苯。在微型液相固定床反应器上考察了HF负载量、反应温度及空速对反应的影响。实验结果表明,氟的最佳负载质量分数为3%,最佳反应条件:反应温度180 ℃,空速2.0 h-1,苯烯物质的量比10∶1。在此条件下,十二碳烯的转化率可以达到94.3%,十二烷基苯选择性可达92.76%。 相似文献
5.
6.
选用空壳型ZSM-5分子筛为母体催化剂,利用固定床反应器考察了煤基乙醇与苯烷基化制备乙苯反应条件对催化性能的影响,并在优化条件下评价空壳型HZSM-5母体催化剂的反应稳定性;研究了水热处理与P或Zn单组分对母体ZSM-5联合改性所得催化剂的烷基化催化性能。结果表明,空壳型HZSM-5母体催化剂用于苯与乙醇烷基化反应,连续反应100 h性能基本没有变化,苯转化率保持在13.4%左右、乙基选择性为97.8%,而二甲苯相对质量分数保持在3 400μg/g。经过单组分改性与水热处理联合改性的空壳型HZSM-5分子筛,可以进一步提高乙基选择性和降低二甲苯杂质质量分数,在苯/乙醇摩尔比为6、反应温度为340℃和空速为6 h-1的优化条件下,苯转化率大于10%,乙基选择性大于99%,二甲苯相对质量分数低于700μg/g,具有很好的应用开发潜力。 相似文献
7.
针对苯与乙醇烷基化制备乙苯的反应,选用纳米聚集体HZSM-5分子筛为母体催化剂,采用固定床反应器考察了反应条件对催化性能的影响,筛选出最优反应条件,并评价了母体催化剂的稳定性;探究了Zn、Mg、P单组分改性以及Zn和Mg、P和Mg复合改性催化剂对反应性能的影响。结果表明,在苯/醇摩尔比为6、空速为6 h-1、反应温度为350℃、载气流量为30 mL/min的条件下,催化剂连续反应300 h苯转化率保持在15%以上,乙苯选择性和乙基产物的选择性分别保持在96.3%和98.8%左右,但二甲苯的质量分数偏高,保持在490μg/g以上。母体催化剂经单组分改性后,苯-乙醇烷基化的副产物二甲苯质量分数均得到降低,经P和Mg复合改性具有更好的效果,苯转化率和乙基选择性分别为15.4%和99.6%,二甲苯质量分数可降低至241μg/g。 相似文献
8.
该发明涉及一种乙烯液相烷基化制乙苯的方法,主要解决以往技术中存在苯和乙烯液相烷基化反应中,催化剂稳定性和再生性能差的问题。该发明通过采用以乙烯和苯为原料,以p沸石分子筛为催化剂,催化剂在使用前先用高温水蒸汽处理,然后再用有机酸处理,反应温度为200—270℃,反应压力为3.0—4.0MPa,苯/乙烯摩尔比为3-10条件下,乙烯发生液相烷基化反应生成乙苯的技术方案较好地解决了该问题,可用于液相烷基化制乙苯的工业生产中。 相似文献
9.
10.
采用负载磷酸的SBA-15分子筛作为催化剂,以苯和十六碳烯为原料,经烷基化反应合成十六烷基苯。在微型液相固定床反应器上考察了反应温度、空速、体系压力、磷酸负载量以及苯烯摩尔比等反应条件对催化剂性能的影响。研究结果表明,磷酸的适宜负载量约为7%(质量分数),适宜反应条件为反应温度180℃、空速为2.0 h^-1、体系压力为2.0 MPa和苯、烯摩尔比为10。在此条件下,十六碳烯的转化率可达到94.5%,十六烷基苯选择性可达93%。催化剂单程寿命达到120 h以上。负载磷酸的SBA-15催化剂呈现较好的催化活性和稳定性。 相似文献
11.
采用AlCl3和[Bmim]Cl不同摩尔比的[Bmim]C1-xA1C13离子液体为催化剂,研究了不同条件下1-十二烯与苯的烷基化反应。实验结果表明,以A1Cl3和[Bmim]Cl的摩尔比为2.0([Bmim]Cl-2A1C13)的离子液体为催化剂,在反应温度25℃、反应时间30 min,苯、烯及离子液体的摩尔比为5︰1︰0.03的条件下,正十二烯的转化率可达98.32%,2-LAB的选择性可达36.76%。离子液体和产物可形成易于分离的双液相,简化了催化剂与产物的分离操作。 相似文献
12.
The alkylation of benzene with 1-dodecene was studied over solid-acid zeolites, such as H-mordenite, H-USY, HY, and H-ZSM-5, in a batch reactor at 140°C and 10 atm. H-mordenite showed the highest selectivity of 78.2% for 2-phenyldodecane with 100% conversion. Depending on the catalyst amount (from 0.5 to 1.0 g) and the molar ratio of benzene to 1-dodecene (from 7 to 10), the conversion of 1-dodecene varied in the range from 63.8 to 100%. Furthermore, modification of H-mordenite by dealumination using nitric acid and by solid ion exchange with Mg2+ and Fe3+ ions led to the improvement of the selectivity for 2-phenyldodecane, and simultaneously reduction of the conversion of 1-dodecene is observed. In addition, it was found by pyridine adsorption FT-IR study that both strong Brønsted and Lewis acid sites are closely related to the conversion. 相似文献
13.
Alkylation of 1-Dodecene with Benzene over H3PW12O40 Supported on Mesoporous Silica SBA-15 总被引:1,自引:0,他引:1
The SBA-15 supported 12-phosphotungstic acid catalysts were prepared and measured in the alkylation of benzene with 1-dodecene at the atmospheric batch reactor. It is found that the catalysts exhibit much higher catalytic activity, selectivity and stability than HY zeolite in this reaction at the reaction temperature of 80 °C, with the 1-dodecene conversion of nearly 90%, 2-phenyldodecane selectivity of nearly 40%, and monoalkylbenzene selectivity of 100%. 相似文献
14.
Alkylation of benzene with 1- dodecene over usy zeolite catalyst: Effect of pretreatment and reaction conditions 总被引:5,自引:0,他引:5
Catalytic activity, stability and selectivity of USY zeolite catalyst for alkylation of benzene with 1-dodecene were investigated
using a continuous fixed bed high pressure microreactor. It is found that the catalytic activity and stability depend closely
on the pretreatment temperature of catalyst and reaction conditions. The best result was obtained at 120 °C and 3.0MPa with
8 molar ratio of benzene to 1-dodecene, and 4 h-1 weight hourly space velocity of reactant over the catalyst with the pretreatment
temperature of 500 °C. Under this condition, the reaction conversion was nearly 100% and no deactivation was observed within
the employed 50 h of time on stream with the selectivity of 2-phenyldodecene being 22%.
This paper is dedicated to Professor Wha Young Lee on the occasion of his retirement from Seoul National University.
On a research leave from Department of Chemical Engineering, Nanjing University of Technology, Nanjing 210009, China. 相似文献
15.
以苯甲醛和甘油为原料,通过活性炭负载磷钨酸(TPA)为催化剂,催化合成苯甲醛甘油缩醛。分别研究了催化剂磷钨酸负载量、反应时间、反应物配比及催化剂用量对合成反应的影响。结果表明,TPA负载量(质量分数)15%,催化剂用量(质量分数)4%,苯甲醛:甘油=1:1.1(摩尔比),反应时间2.0h,苯甲醛甘油缩醛的收率可达96.4%。 相似文献
16.
17.
18.
长链烷基苯(LAB)是制备合成洗涤剂烷基苯磺酸钠的主要原料,传统上LAB采用无机液体酸(HF)为催化剂将苯和长链烯烃烷基化而制得。在LAB的诸多异构体中,2-LAB因其更高的溶解性和可降解性而更受欢迎。使用低温成胶的策略,以水热合成法合成LB-16有机硅杂化分子筛催化剂,并考察其在LAB合成中的催化性能。结果表明,在反应温度190℃、空速0.2 h-1、苯烯物质的量比15∶1条件下,经过1 000 h催化试验,1-十二烯转化率大于99%,2-LAB选择性51%。LB-16有机硅杂化分子筛催化剂对苯与1-十二烯合成反应具有较好的催化活性和稳定性,同时对2-LAB具有较高的选择性,具有工业化应用前景。 相似文献
19.
Aluminum impregnated silica catalyst for Friedel-Crafts reaction:Influence of ordering mesostructure
Friedel-Crafts alkylation of benzene with linear chain olefin (C10-C14),which is an important reaction of synthetic detergent,was studied via different catalysts of aluminum impregnated silica molecular sieves.AlCl3 was immobilized on silica molecular sieves with different channel structures,hexagonal packing channels network (SBA-15,MCM-41),and disordered channel network (SiO2,SiO2-Gel) by impregnation.XRD and N2 adsorption-desorption isotherms confirmed that the specific mesoporous structures were maintained for order channel network catalyst after impregnation.Catalytic activities were investigated under different conditions.The influences of channel structure were discussed.The results showed that catalyst based on mesoporous like SBA-15 had the highest catalytic activities and 2-LAB selectivity compared with other catalysts in this work.The highest 2-LAB selectivity was nearly 50% when 1-dodecene conversion was nearly 100%.At low 1-dodecene conversion or higher benzene/1-dodecene molar ratio,2-LAB selectivity was nearly 60%. 相似文献
20.
以对甲苯磺酸为催化剂,正丁酸与正戊醇为原料催化合成丁酸正戊酯。较系统地研究了酸醇量比、催化剂用量、带水剂用量及反应时间等条件对收率的影响。结果表明:在固定正丁醇用量为0.2mol的情况下,在n(正丁酸):n(正戊醇)=1:1.4,催化剂占反应物料总量2.5%,带水剂环己烷的用量为6mL,反应时间2.5h的优化条件下,产品收率可达83.3%。 相似文献