TiO2/TNO homojunction introduced in a dye‐sensitized solar cell with a novel TNO transparent conductive oxide film

In this study, niobium‐doped titanium oxide (TNO) was employed for a novel transparent conductive oxide (TCO) film to construct a porous‐TiO₂/TNO homojunction in a dye‐sensitized solar cell (DSSC). However, considering a balance between the electrical and optical properties of the TCO film, the sheet resistance in TNO was tuned to be higher than that in a typical fluorine‐doped tin oxide (FTO). The photovoltaic performance of the cell with the TNO film (TNO cell) was optimized to be almost comparable to that with a conventional FTO film (FTO cell) by coating the surface of the porous‐TiO₂ layer with a thin alumina or magnesia film to block a back reaction within the cell. An electrochemical impedance measurement was conducted to determine the detailed photovoltaic performance from the viewpoint of electron transportation in the cell. R₁, the real part of ω₁, indicated that electron transportation at the porous‐TiO₂/TNO interface was more favorable than that at the porous‐TiO₂/FTO interface, which was supported by AC phase change in the cell at a high‐frequency range. We found that the homojunction newly introduced in the cell is one of the key concepts for developing a DSSC into a high‐performance photovoltaic device.     

Synergetic effect of graphene sheet and three‐dimensional crumpled graphene on the performance of dye‐sensitized solar cells

Herein, an improved structure of the dye‐sensitized solar cell (DSSC) is demonstrated which is composed of surface modified fluorine‐doped tin oxide (FTO) glass with graphene (GR) sheets and TiO₂ films incorporated with three‐dimensional crumped graphene (3‐D CGR)/GR sheets. The morphologies of the as‐prepared GR sheets on FTO glasses and 3‐D CGR/GR sheets/TiO₂ films were observed by field‐emission scanning electron microscopy. Light harvesting and charge recombination kinetics were investigated with a solar simulator and electrochemical impedance spectroscopy analysis. In addition to the reduced charge resistance by the GR modified FTO, the enhanced dye loading capability of the 3‐D CGR, and the rapid charge transport by the 2‐D GR sheets, the power conversion efficiency was 7.2%, which was an increase of 56% compared to a “conventional” structured DSSC. © 2015 American Institute of Chemical Engineers AIChE J, 62: 574–579, 2016     

Application of thermosetting organic solvent free polymer gel electrolyte in quasi‐solid‐state dye‐sensitized solar cell

A kind of thermosetting organic solvent free polymer gel electrolyte with oligomer ethylene glycol as liquid phase was prepared and applied in quasi‐solid‐state dye‐sensitized solar cell (QS‐DSSC). The viscosity and the ionic conductivity of the polymer gel electrolyte are sensitive to the changed temperature. The photovoltaic performance of QS‐DSSC is also improved with the increased temperature due to the increased ionic conductivity and diffusion coefficient of iodide in polymer gel electrolyte. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Effect of nano‐TiO2 dispersion on PEO polymer electrolyte property

Polymer electrolyte membranes based on poly(ethylene oxide) (PEO) doped with TiO₂ nanoparticles were synthesized by simple solution cast technique. Mesoporous TiO₂ film was prepared by doctor‐blade method. The modified polymer membranes and the mesoporous films were characterized by SEM, TEM, AFM, ionic conductivity, and J‐V measurements. Dye‐sensitized solar cells (DSSC) have been fabricated in which PEO‐polymer electrolyte doped with and without nano‐TiO₂ were sandwiched between porous TiO₂ and counter electrodes. The DSSC with nano‐TiO₂ doped polymer electrolyte shows better performance (1.68%) in comparison with pristine polymer electrolyte (1.07%), which is due to improved ionic conductivity value in polymer electrolyte system by nano‐TiO₂ doping. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

TiO2–BaTiO3 nanocomposite for electron capture in dye‐sensitized solar cells

Different compositions of TiO₂–BaTiO₃ nanocomposites are synthesized with various weight ratios for dye‐sensitized solar cell (DSSC) applications. TiO₂ and BaTiO₃ nanoparticles (NPs) are synthesized by sol‐gel and solvothermal methods, respectively and are employed as the photoanode electrodes. BaTiO₃ NPs have pure cubic perovskite crystal structure with an average size of 20‐40 nm, while TiO₂ NPs show pure anatase phase with 15‐30 nm size. The power conversion efficiency (PCE) enhancement of the cells is first attained by controlling the thickness of the films for light harvesting improvement. The fabricated DSSC composed of pure BaTiO₃ NPs with an optimal thickness of 25 μm shows efficiency of 6.83%, whereas that made of pure TiO₂ NPs with 14 μm thickness has cell efficiency of 7.24%. Further improvement of cell efficiency is achieved by preparation of binary oxide nanocomposites using TiO₂ and BaTiO₃ NPs with various weight ratios. The highest PCE of 9.40% is obtained for the nanocomposite with TiO₂:BaTiO₃=85:15 (wt%). The enhancement is assigned to less recombination of photo‐generated electrons and higher incident photon to current conversion yield as a result of rapid charge collection and higher dye sensitization.     

Improved Efficiency of Dye‐Sensitized Solar Cells Based on a Single Layer Deposition of Skein‐Like TiO2 Nanotubes

We present a new TiO₂ morphology, featuring high surface area and open structure, synthesized by a two‐step chemical route for the manufacture of dye‐sensitized solar cells (DSSCs). This construct is sets of intertwined one‐dimensional (1D) nanostructures (i.e., nanotubes), so‐called skein‐like nanotubes (NTs). Such morphology is produced by a combination of TiC oxidation and hydrothermal processes. The mesoporous TiO₂ nanoparticles, as the product of TiC oxidation operation, is used as the precursor of hydrothermal process to grow the skein‐like NTs. The effect of processing parameters of TiC oxidation and hydrothermal processes is studied. The skein‐like morphology enables to eliminate the conventional three or fourfold layer deposition process by a single layer deposition of TiO₂ NTs. The novel TiO₂ morphology enhances photon capture of fabricated DSSC by exerting a triple function mechanism including improvement of light scattering, dye sensitization, and electron transport. The presented strategy demonstrates the feasibility of the new concept for improvement of cell efficiency by effective light management.     

Polyvinyl pyrrolidone aided preparation of TiO2 films used in flexible dye-sensitized solar cells

Polyvinyl pyrrolidone (PVP) is introduced to low temperature preparation of a good quality TiO₂ film used in flexible dye-sensitized solar cells (DSSCs). The samples are characterized by scanning electron microscopy and UV–vis absorption spectra, the photovoltaic performance of the DSSC is measured. It is found that PVP can improve the dispersion of TiO₂ particles and the adherence of TiO₂ particles to flexible substrate, as well as the adsorption of sensitized dye to TiO₂ film. Additionally, ultraviolet light irradiation can eliminate organics remained on the surface the TiO₂ film and improve the surface state of TiO₂ film. Under an optimal condition, a flexible DSSC using TiO₂ film doped PVP and UV irradiation treated achieves a light-to-electric energy conversion efficiency of 3.02% under irradiation with a simulate solar light intensity of 100 mW cm⁻².     

Enhanced electron collection efficiency of nanostructured dye‐sensitized solar cells by incorporating TiO2 cubes

Herein, enhancement of dye‐sensitized solar cell (DSC) performance is reported by combining the merits of the dye loading of TiO₂ nanoparticles and light scattering, straight carrier transport path, and efficient electron collection efficiency of TiO₂ cubes. We fabricate DSC devices with various arrangement styles and compositions of the electrodes in the forms of monolayer and double layer films. For this purpose, the solvothermal synthesized TiO₂ cubic particles (100‐600 nm) are employed as the scattering layer, whereas TiO₂ nanoparticles (15‐30 nm) synthesized via a combination of solvothermal and sol‐gel routes are used as the active layer of devices. We improve the photovoltaic characteristics of DSCs by two mechanisms. First, the light harvesting of DSC devices made of nanoparticles is improved by controlling the thickness of monolayer films, reaching the highest efficiency of 7.0%. Second, the light scattering and electron collection efficiency are enhanced by controlling the composition of double layer films composed of mixtures of TiO₂ nanoparticles and cubes, obtaining the maximum efficiency of 8.21%. The enhancements are attributed to balance between charge transfer resistance and charge recombination of photo‐generated electrons as well as dye loading and light scattering.     

Wire‐shaped,dye‐sensitized solar cells with poly(vinyl alcohol) gel electrolyte and metal filaments

A kind of wire‐shaped, dye‐sensitized solar cell (WDSSC) composed of poly(vinyl alcohol) (PVA) gel electrolyte and filament‐formed electrodes of titanium and platinum was prepared, and its photovoltaic performance was analyzed with the variations in the dimensions of the electrodes and cells. The dimensions of the wire‐shaped cell were adjusted through the thickness of the TiO₂ layer, the amount of PVA gel electrolyte, and length of the Pt filament. The dominant parameters determining the cell performance were mainly analyzed with the results from the various scanning electron microscopy images and fitted plots of electrochemical impedance spectroscopy. Although the conversion efficiencies of the fabricated WDSSCs were relatively lower than those of the conventional dye‐sensitized solar cells, this development should provide important guiding directions for the design of similar WDSSCs with higher efficiencies. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43439.     

Preparation of polyaniline/TiO2 nanocomposite film with good adhesion behavior for dye‐sensitized solar cell application

In this study, novel Polyaniline (PAni)/TiO₂ nanocomposites were applied on fluoride‐doped tin oxide (FTO) glass to act as an efficient counter electrode in dye‐sensitized solar cell (DSSC) application. PAni/TiO₂ nanocomposites were synthesized via chemical oxidation process using di‐2‐ethylhexylsulfosuccinate sodium salt (NaDEHS) as dopant. The nanocomposites were characterized using fourier transform infrared and ultraviolet‐visible spectrometers. In the application of PAni as the counter electrode in the solar cell, the film showed poor adhesion on the FTO glass. Palm oil‐based alkyd was introduced into the nanocomposite mixture to improve the adhesion of the film. The findings in the work show that strong adhesion of PAni on FTO glasses has led to higher incident photon to current conversion efficiency (IPCE) in solar cell. The short circuit current (Jsc), Voc (open circuit voltage), and IPCE of the resulted PAni/TiO₂ counter electrode with good adhesion in DSSC are 15.8 mA/cm², 670 mV, and 3.0%, respectively. POLYM. COMPOS., 34:1884–1891, 2013. © 2013 Society of Plastics Engineers     

ZnO photoanodes with different morphologies grown by electrochemical deposition and their dye-sensitized solar cell properties

In this article, we grew zinc oxide (ZnO) samples with different morphologies, e.g. film, nanowire and nanosheet, with electrochemical deposition (ECD) by controlling the precursor concentration and the growth mechanism was also discussed. The morphology influence on the photovoltaic conversion efficiency of the dye-sensitized solar cells (DSSC) assembled with different ZnO photoanodes was investigated by measuring current density–voltage (J–V) curve, quantum efficiency (QE) spectrum and electrochemical impedance spectrum (EIS). It was found that the DSSC constructed with ZnO nanowire array as photoanode can absorb more dye, improve the photon utilization rate and provide rapid collection channels for the photoexcited carriers. Therefore, the photovoltaic conversion efficiency of ZnO nanowire DSSC was improved.     

An inverted fabrication method towards a flexible dye sensitized solar cell based on a free-standing TiO2 nanowires membrane

This paper reports an inverted fabrication process for the photoanode of a flexible dye sensitized solar cell (DSSC). This procedure involves assembling a free-standing TiO₂ nanowires/nanoparticles hybrid membrane, via high temperature annealing, sputtering an indium tin oxide (ITO) layer onto this membrane, and transferring these onto a polydimethylsiloxane (PDMS) substrate. The inverted procedure prevents thermal decomposition of polymer substrate, whilst enabling effective thermal treatment of the functionalized titanium oxide. The flexible DSSC fabricated in this way has an efficiency of 2.7%, which is comparable with rigid device constructed using similar materials.     

Synthesis of quaternized ammonium iodide‐containing conjugated polymer electrolytes and their application in dye‐sensitized solar cells

A series of conjugated polymer electrolytes (CPEs) comprising fluorene/carbazole or thiophene/carbazole backbones with quaternized ammonium iodide groups were synthesized and used in polymer solution and polymer gel electrolytes in dye‐sensitized solar cells (DSSCs). The photovoltaic (PV) performances became markedly poorer with increasing CPE content for the DSSCs based on polymer solution electrolytes. However, the PV performances were not significantly affected with increasing CPE content for the DSSCs fabricated from poly(ethylene oxide) (PEO)/CPE blend‐based gel‐type electrolytes. Moreover, higher PV efficiencies and stabilities were obtained for the DSSCs based on PEO/CPE blend gel electrolytes as compared to the DSSCs based on PEO gel electrolyte. The electrochemical impedance and PV properties of the DSSCs based on polymer solution electrolytes and on polymer gel electrolytes were determined as a function of the CPE concentration. Copyright © 2010 Society of Chemical Industry     

Double‐Layer Structure Photoanode with TiO2 Nanotubes and Nanoparticles for Dye‐Sensitized Solar Cells

Here, we report a novel double‐layer structure photoanode with TiO₂ nanotube (TNT) layer and TiO₂ nanoparticle (TP) layer via a two‐step method of electrochemical anodization and screen printing for dye‐sensitized solar cells (DSSCs). The results indicate that DSSCs with this double‐layer structure have significant advantages of large surface area, long electron lifetime, superior electron recombination restraint characteristics, and high light scattering. The layer thickness of nanotubes and nanoparticles is also investigated and finally an optimized double‐layer structure with excellent performance is prepared. With such a double‐layer structure photoanode, DSSC with a relative high conversion efficiency of 6.43% and a short‐circuit photocurrent density of 16.40 mA·cm^?2 is obtained.     

Pulsed laser ablation in liquid synthesis of ZnO/TiO2 nanocomposite catalyst with enhanced photovoltaic and photocatalytic performance

In this work, we employed an impurity-free nanoparticle synthesis technique, known as pulsed laser ablation in liquid (PLAL), to integrate titanium dioxide nanoparticles (TiO₂ NPs) into zinc oxide nanorods (ZnO NRs) with varying relative proportions. The main objective of this integration was to enhance the charge carrier separation of photo-generated electron hole pairs during solar irradiation. For the synthesis process, an Nd:YAG laser at 532 nm wavelength was applied as an ablation source, along with deionized water as a solvent medium in which the precursor materials were dispersed prior to laser irradiation. The nanocomposites were characterized by X-ray diffraction (XRD), UV–vis absorption and in-situ Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HR-TEM) and field emission scanning electron microscopy (FE-SEM). The synthesized nanocomposites were primarily utilised in two applications: firstly, as a catalyst in the degradation of methyl orange (MO) and secondly, as photo-anode in dye sensitized solar cell (DSSC). Our research has demonstrated that optimal performance was obtained for the nanocomposite containing 10% and 90% (by weight) TiO₂ NPs and ZnO respectively, which we define as the ideal nanocomposite. Relative to pure ZnO, the photo-conversion efficiency of the ideal composite was improved substantially by 63.73%, whilst the photo-degradation rate was enhanced by 3 fold. The oxidation state and the microstructural of the segregated ideal nanocomposite confirms that oxygen vacancy defects were created when perfect surface integration occurs between TiO₂ and ZnO. Nonetheless, we believe that the performance enhancement is predominantly due to the excellent charge carrier separation and fast interfacial electron flow in this nanocomposite.     

Enhancing the performance of dye-sensitized solar cells based on an organic dye by incorporating TiO2 nanotube in a TiO2 nanoparticle film

The photoelectrochemical properties of a high molar extinction coefficient charge transfer organic dye containing thienylfluorene segment called FL, and the effect of incorporating TiO₂ nanotube (TiNT) in TiO₂ nanoparticle film along with the above dye on the photovoltaic performance of dye-sensitized solar cells (DSSCs) were investigated. The influence of soaking time of the TiO₂ electrode in dye solution and the effect of varying its concentration, on the solar cell efficiency was also studied. Cyclic voltammetric (CV) analysis revealed the linear relationship between the anodic peak current and the scan rate, indicating a surface-confined diffusion process.The surface morphology of TiNT was characterized using SEM, TEM and XRD. The open-circuit voltage (V_OC) of the DSSC increased with the increase in the wt% of TiNT and shows optimal value at about 5 wt%, which is correlated with the suppression of the electron recombination as found out from the electron lifetime studies.The electrochemical impedance spectroscopy (EIS) technique was employed to quantify the charge transport resistance (R_ct) and electron lifetime under different ratios of the TiNT/nanoparticle. The electron lifetimes of the DSSCs based on FL and N3 dye were very close to one another and the DSSC based on the FL showed respectable photovoltaic performance of ca. 7.8% under the light intensity of 100 mW cm⁻² (AM 1.5G).     

Theoretical modelling of the electrode thickness effect on maximum power point of dye‐sensitized solar cell

The maximum power point (MPP) of a dye‐sensitized solar cell (DSSC) is often more important than the open‐circuit voltage and the short‐circuit current as MPP better represents the DSSC power output and energy conversion efficiency. In this investigation, the DSSC J–V characteristics and MPP were studied using a simple theoretical electron diffusion model. Parametric analyses were performed to determine the particular effect of electrode thickness on the MPP output. The analytical results are well consistent with the experimental results published in the literature. In the optimization analysis, it was specially found that the optimal electrode thickness for the highest MPP is rather insensitive to the operating conditions. It implies that an optimally designed DSSC can be always operated at its highest MPP regardless of any geographical, seasonal, and solar hour factors. Such an important attribute facilitates the design and manufacture of DSSC for worldwide commercialization at competitive costs.     

Effect of the grain size of nanoparticle dye‐coated titanium dioxide on the short‐circuit current density and open‐circuit voltage of an indium tin oxide/titanium dioxide/poly(acrylonitrile)–propylene carbonate–lithium perchlorate/graphite solar cell

A dye‐sensitized indium tin oxide (ITO)/titanium dioxide (TiO₂)/polyacrylonitrile (PAN)–propylene carbonate (PC)–lithium perchlorate (LiClO₄)/graphite solar cell was fabricated, and its performance was tested in the dark and under the illumination of a 100 mW/cm² light. Three TiO₂ samples were used in the device, namely, uncoated TiO₂, a TiO₂ film coated with methyl red dye, and a TiO₂ film coated with coumarin dye. The films were deposited onto an ITO‐covered glass substrate by a controlled hydrolysis technique assisted with a spin‐coating technique. The films were characterized by scanning electron microscopy to determine their average grain size. The smallest grain size (48 nm) was obtained for the uncoated film. An electrolyte of PAN–LiClO₄ with PC plasticizer was prepared by a solution‐casting technique. A graphite electrode was prepared on a glass slide by an electron‐beam evaporation technique. The device showed rectification properties in the dark and showed a photovoltaic effect under illumination. The device with the uncoated TiO₂ film showed the highest short‐circuit current density (2.0 μA/cm²) and an open‐circuit voltage of 0.64 V because it possessed the smallest grain size. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Improved dye-sensitized solar cell with a ZnO nanotree photoanode by hydrothermal method

This study investigated the influence of ZnO nanostructures on dye adsorption to increase the photovoltaic conversion efficiency of solar cells. ZnO nanostructures were grown in both tree-like and nanorod (NR) arrays on an AZO/FTO film structure by using a hydrothermal method. The results were observed in detail using X-ray diffraction, field-emission scanning electron microscopy (FE-SEM), UV-visible spectrophotometry, electrochemical impedance spectroscopy, and solar simulation. The selective growth of tree-like ZnO was found to exhibit higher dye adsorption loading and conversion efficiency than ZnO NRs. The multiple ‘branches’ of ‘tree-like nanostructures’ increases the surface area for higher light harvesting and dye loading while reducing charge recombination. These improvements result in a 15% enhancement in power conversion. The objective of this study is to facilitate the development of a ZnO-based dye-sensitized solar cell.     

Aqueous Colloidal Stability Evaluated by Zeta Potential Measurement and Resultant TiO2 for Superior Photovoltaic Performance

Controlling the morphological structure of titanium dioxide (TiO₂) is crucial for obtaining superior power conversion efficiency for dye‐sensitized solar cells. Although the sol–gel‐based process has been developed for this purpose, there has been limited success in resisting the aggregation of nanostructured TiO₂, which could act as an obstacle for mass production. Herein, we report a simple approach to improve the efficiency of dye‐sensitized solar cells (DSSC) by controlling the degree of aggregation and particle surface charge through zeta potential analysis. We found that different aqueous colloidal conditions, i.e., potential of hydrogen (pH), water/titanium alkoxide (titanium isopropoxide) ratio, and surface charge, obviously led to different particle sizes in the range of 10–500 nm. We have also shown that particles prepared under acidic conditions are more effective for DSSC application regarding the modification of surface charges to improve dye loading and electron injection rate properties. Power conversion efficiency of 6.54%, open‐circuit voltage of 0.73 V, short‐circuit current density of 15.32 mA/cm², and fill factor of 0.73 were obtained using anatase TiO₂ optimized to 10–20 nm in size, as well as by the use of a compact TiO₂ blocking layer.