Mechanochemical synthesis of Ti1−xZrxB2 and Ti1−xHfxB2 solid solutions

Solid solutions of TiB₂-ZrB₂ and TiB₂-HfB₂ were obtained under an inert atmosphere by high-energy ball-milling mixtures of Ti/Zr/B and Ti/Hf/B, respectively. Milling promoted mechanically induced self-sustaining reactions (MSR), and the ignition time was dependent on the initial composition of the mixture. The stoichiometry of Ti_1−xZr_xB₂ and Ti_1−xHf_xB₂ solid solutions was controlled by adjusting the atomic ratio of the reactants. The solid solutions were characterised by X-ray diffraction, transmission electron microscopy, electron diffraction, and energy dispersive X-ray spectroscopy. The results revealed that TiB₂-ZrB₂ possessed a nanometric microstructure and good chemical homogeneity. However, in the TiB₂-HfB₂ system, an inhomogeneous solid solution was obtained when a Ti-rich mixture was employed. The solid solutions showed good thermal stability; thus, can be used as raw materials for the development of technological materials for structural applications.     

Structural,magnetic and dielectric behavior of Mg1−xCaxNiyFe2−yO4 nano-ferrites synthesized by the micro-emulsion method

Ca–Ni co-substituted samples of nanocrystalline spinel ferrites with chemical formula Mg_1−xCa_xNi_yFe_2−y O₄ (x=0.0–0.6, y=0.0–1.2) were synthesized by the micro-emulsion method and were annealed at 700 °C for 7 h. The synthesized samples were characterized by x-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, vibrating sample magnetometry (VSM) and dielectric measurements. The XRD and FTIR analysis reveals that single phase samples can be achieved by substituting Ca and Ni ions at Mg and Fe sites respectively in cubic spinel nano-ferrites. The crystallite size of the synthesized samples was found in the range 29–45 nm. The saturation magnetization (M_s) increases from 9.84 to 24.99 emu/g up to x=0.2, y=0.4 and then decreases, while the coercivity (H_c) increases continuously from 94 to 153 Oe with the increase in dopants concentration. The dielectric properties of these nano materials were also studied at room temperature in the frequency range 100 MHz to 3 GHz. The dielectric parameters were found to decrease with the increased Ca–Ni concentration. Further the peaking behavior was observed beyond 1.5 GHz. The frequency dependent dielectric properties of all the samples have been explained qualitatively on the basis of the Maxwell–Wagner two-layer model according to Koop's phenomenological theory. The enhanced magnetic parameters and reduced dielectric properties make the synthesized materials suitable for switching and high frequency applications, respectively.     

Preparation and microstructural characterization of (Nd1−xGdx)2(Ce1−xZrx)2O7 solid solutions

(Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ (0 ≤ x ≤ 1.0) powders with an average particle size of 100 nm were synthesized with chemical-coprecipitation and calcination method, and were characterized by X-ray diffractometry and scanning electron microscopy. The sintering behaviour of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ powders was studied by pressureless sintering at 1600–1700 °C for 10 h in air. The relative densities of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions increase with increasing the sintering temperature, and gradually decrease with increasing the content of neodymium and cerium at identical temperature levels. (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions have a single phase of defect fluorite-type structure among all the composition combinations studied. The lattice parameters of (Nd_1−xGd_x)₂(Ce_1−xZr_x)₂O₇ solid solutions agree well with the Vegard's rule.     

VUV photoluminescence properties of Y1−xGdxVO4:Eu phosphors prepared by ultrasonic spray pyrolysis

The red-emitting (Y_1−xGd_x)_0.94Eu_0.06VO₄ (0 ≤ x ≤ 1.0) phosphors were synthesized by ultrasonic spray pyrolysis. The (Y_1−xGd_x)_0.94Eu_0.06VO₄ (0 ≤ x ≤ 1.0) phosphors had the tetragonal xenotime structure with a space group of I4₁/amd (1 4 1). The calculated crystallite sizes of the annealed phosphors ranged from 58 to 68 nm. In this study, we discussed the photoluminescence properties of the (Y_1−xGd_x)_0.94Eu_0.06VO₄ phosphors under VUV excitation, depending on Gd content. The emission intensity of the (Y_1−xGd_x)_0.94Eu_0.06VO₄ phosphors increased with increasing Gd content up to x = 0.5, and then decreased with a further increase in Gd content. The purest red color was obtained for the (Y_0.5Gd_0.5)_0.94Eu_0.06VO₄ phosphors.     

Synthesis,structural analysis and dielectric properties of Ba8(Mg1−xZnx)Nb6O24 hexagonal perovskites

Ba₈(Mg_1−xZn_x)Nb₆O₂₄ (x=0, 0.2, 0.4, 0.6, 0.8 and 1) ceramics were prepared through the conventional solid-state route. The materials were calcined at 1250 °C and sintered at 1375–1425 °C. The structure of the system was analyzed using X-ray diffraction and vibrational spectroscopic studies. The microstructure of the sintered pellet was analyzed using scanning electron microscopy. The dielectric constant (ε_r), temperature coefficient of resonant frequency (τ_f) and the unloaded quality factor (Q_u) were measured in the microwave frequency region. The τ_f values of the compositions were reduced by varying the value of x from 0 to 1. The dielectric responses to frequency were also studied in the radio frequency region. The compositions have good microwave dielectric properties and hence are suitable for dielectric resonator applications.     

Synthesis of negative thermal expansion materials ZrW2−xMoxO8 (0 ≤ x ≤ 2) using hydrothermal method

Negative thermal expansion materials ZrW_2−xMo_xO₈ (0 ≤ x ≤ 2) have been successfully synthesized by the reaction of a mixture of ammonium tungstate and ammonium molybdate with zirconium oxynitrate using a hydrothermal method. Effect of substituted ion Mo on the microstructure, α-to-β and cubic to trigonal phase transition in resulting ZrW_2−xMo_xO₈ powders was examined by the XRD experiments. It was found that the structural phase transition temperature decreased slightly with increasing substituted content. The cubic to trigonal phase transition was also influenced by substituted content. The resulting products decomposed to WO₃/MoO₃ and ZrO₂ as temperature increasing when x ≤ 0.5 and while x > 0.5, the cubic phase transited to trigonal phase. The effect of substituted Mo on the morphology of resulting products was also investigated by SEM experiments.     

Structure,magnetic and electrical transport properties of the perovskites Sm1−xCaxFe1−xMnxO3

The structure of series Sm_1−xCa_xFe_1−xMn_xO₃ (0.0 ≤ x ≤ 1.0) compounds was investigated. The lattice parameters increase with coupled substitution Sm³⁺ by Ca²⁺ and Mn⁴⁺ for Fe³⁺. The variation of parameter, c, is larger than that of a and b, respectivly. The detailed analysis of magnetic properties of series Sm_1−xCa_xFe_1−xMn_xO₃ (0.1 ≤ x ≤ 0.9) shows that local magnetic interaction between Fe³⁺ and Fe³⁺ and Mn⁴⁺ and Mn⁴⁺ at below magnetic transition temperature is antiferromagnetic. Above magnetic transition temperature the presence of large magnetic cluster is proposed and the sizes of magnetic clusters decrease with Mn⁴⁺. The electrical transport behaviors related with small polaron hopping and variable range hopping models.     

Magnetic and magnetoresistive properties of La0.65−xEuxSr0.35MnO3

Eu-doped perovskites La_0.65−xEu_xSr_0.35MnO₃ (0.05 ≤ x ≤ 0.30) were synthesized by sol–gel method using citric acid and characterized by X-ray diffraction, magnetization, resistivity and magnetoresistance (MR) experiments. All samples had a single hexagonal perovskite structure. As x increased from 0.05 to 0.30, the Curie temperature T_C for the samples decreased from 352 to 242 K. It was found that two transition points appeared when the resistivity changed with increasing temperature, and upon an application of a magnetic field of 20 kOe the maximum magnetoresistivity of 18% for the La_0.65−xEu_xSr_0.35MnO₃ with x = 0.20 was obtained at room temperature 300 K. The mechanism of the transitions for the samples was explored.     

Electrodeposition of P-type BixSb2−xTey thermoelectric film from dimethyl sulfoxide solution

The electrochemical behaviors of Bi(III), Te(IV), Sb(III) and their mixtures in DMSO solutions were investigated using cyclic voltammetry and linear sweep voltammetry measurements. On this basis, Bi_xSb_2−xTe_y film thermoelectric materials were prepared by potentiodynamic electrodeposition technique from mixed DMSO solution, and the compositions, structures, morphologies as well as the thermoelectric properties of the deposited films were also analyzed. The results show that Bi_xSb_2−xTe_y compound can be prepared in a very wide potential range by potentiodynamic electrodeposition technique in the mixed DMSO solutions. After anneal treatment, the deposited film prepared in the potential range of −200 to −400 mV shows the highest Seebeck coefficient (185 μV/K), the lowest resistivity (3.34 × 10⁻⁵ Ω m), the smoothest surface, the most compact structure and processes the stoichiometry (Bi_0.49Sb_1.53Te_2.98) approaching to the Bi_0.5Sb_1.5Te₃ ideal material most. This Bi_0.49Sb_1.53Te_2.98 film is a kind of nanocrystalline material and (0 1 5) crystal plane is its preferred orientation.     

Structure,dielectric and optical properties of Bi1.5+xZnNb1.5O7+1.5x pyrochlores

Non-stoichiometric pyrochlore ceramics with formula Bi_1.5+xZnNb_1.5O_7+1.5x were systematically investigated. Crystal structures of the compounds were studied by X-ray diffraction (XRD) technique. The structures were identified as pure cubic pyrochlores when |x| < 0.1. Dielectric and optical properties of the compositions when x = −0.1, 0 and 0.1 were studied. All samples have high resistivities and low dielectric loss. With increasing x in Bi_1.5+xZnNb_1.5O_7+1.5x, the lattice constant, permittivity, temperature coefficient of permittivity and thermal expansion coefficient increased, while dielectric loss decreased. Raman spectra indicated that the intensity of Bi–O stretching become stronger with increasing x. A vibration mode emerging at 861 cm⁻¹ when x = −0.1 means that the B–O coordination environment is significantly more disordered. Absorption spectra suggested that the bandgap energy become lower from 2.86 to 2.70 eV as lattice constants increased. Strong absorption occurs at wavelengths from 433 to 459 nm, shows that samples have the ability to respond to wavelengths in the visible light region.     

Spray pyrolysis synthesis of nanostructured LiFexMn2−xO4 cathode materials for lithium-ion batteries

A series of partially Fe-substituted lithium manganese oxides LiFe_xMn_2−xO₄ (0 ≦ x ≦ 0.3) was successfully synthesized by an ultrasonic spray pyrolysis technique. The resulting powders were spherical nanostructured particles which comprised the primary particles with a few tens of nanometer in size, while the morphology changed from spherical and porous to spherical and dense with increasing Fe substitution. The densification of particles progressed with the amount of Fe substitution. All the samples exhibited a pure cubic spinel structure without any impurities in the XRD patterns.The as-prepared powders were then sintered at 750 °C for 4 h in air. However, the particles morphology and pure spinel phase of LiFe_xMn_2−xO₄ powders did not change after sintering. The as-sintered powders were used as cathode active materials for lithium-ion batteries, and cycle performance of the materials was investigated using half-cells Li/LiFe_xMn_2−xO₄. The first discharge capacity of Li/LiFe_xMn_2−xO₄ cell in a voltage 3.5-4.4 V decreased as the value x increased, however these cells exhibited stable cycling performance at wide ranges of charge-discharge rates.     

Galvanic displacement of BixTey thin films from sacrificial iron group thin films

Bi_xTe_y thin films synthesized by galvanic displacement were systematically investigated by observing open circuit potential (OCP), surface morphology, microstructure and film composition. Surface morphologies and crystal structures of synthesized Bi_xTe_y thin films were strongly depended on the type of the sacrificial materials (i.e., nickel (Ni), cobalt (Co) and iron (Fe)). Galvanically deposited Bi_xTe_y thin films from the sacrificial Ni and Co thin films exhibited Bi₂Te₃ intermetallic compounds and hierarchical structures with backbones and sub-branches. A linear relationship of deposited Bi content in Bi_xTe_y thin films as a function of [Bi³⁺]/[HTeO₂⁺] ratio (within a range of less than 0.8) in the electrolyte was also observed. Surface morphologies of Bi_xTe_y thin films were altered with the film composition.     

A novel lithium intercalation compound based on the layered structure of lithium nitridonickelates Li3−2xNixN

New lithium nickel nitrides Li_3−2xNi_xN (0.20 ≤ x ≤ 0.60) have been prepared and investigated as negative electrode in the 0.85/0.02 V potential window. These materials are prepared from a Ni/Li₃N mixture at 700 °C under a nitrogen flow. Their structural characteristics as well as their electrochemical behaviour are investigated as a function of the nickel content. For the first time are reported here the electrochemical properties of a lithium intercalation compound based on a layered nitride structure. The Li_3−2xNi_xN compounds can be reversibly reduced and oxidized around 0.5 V versus Li/Li⁺ leading to specific capacities in the range 120-160 mAh/g depending on the nickel content and the C rate. Due to a large number of lithium vacancies, the structural stability provides an excellent capacity retention of the specific capacity upon cycling.     

A novel synthesis route to Sn1−xRExO2−x/2 nanorods via microwave-induced salt-assisted solution combustion process

Sn_1−xRE_xO_2−x/2 (RE=Y, La, Gd and Nd) nanorods have been prepared by annealing the as-obtained products from microwave-induced KCl-assisted solution combustion reaction. The phase evolution in the synthesis process was investigated by an X-ray diffractometer. Accordingly, the possible growth mechanism of Sn_1−xRE_xO_2−x/2 nanorods was discussed based on oriented attachment by polar forces. The results showed that the Sn_0.8Y_0.2O_1.9 nanorods were rutile-structured single crystals with 8–12 nm diameter and 100–200 nm length. Proper addition of KCl into the redox mixture solution is critical to the formation of Sn_1−xRE_xO_2−x/2 nanorods. The approach is convenient, inexpensive and efficient for the high yield preparation of Sn_1−xRE_xO_2−x/2 nanorods.     

Synthesis and characterization of MoOx-Pt/C and TiOx-Pt/C nano-catalysts for oxygen reduction

The oxygen reduction reaction (ORR) was studied at carbon supported MoO_x-Pt/C and TiO_x-Pt nanocatalysts in 0.5 mol dm⁻³ HClO₄ solution, at 25 °C. The MoO_x-Pt/C and TiO_x-Pt/C catalysts were prepared by the polyole method combined by MoO_x or TiO_x post-deposition. Home made catalysts were characterized by TEM and EDX techniques. It was found that catalyst nanoparticles were homogenously distributed over the carbon support with a mean particle size about 2.5 nm. Quite similar distribution and particle size was previously obtained for Pt/C catalyst. Results confirmed that MoO_x and TiO_x post-deposition did not lead to a significant growth of the Pt nanoparticles.The ORR kinetics was investigated by cyclic voltammetry and linear sweep voltammetry at the rotating disc electrode. These results showed the existence of two E − log j regions, usually observed with polycrystalline Pt in acid solution. It was proposed that the main path in the ORR mechanism on MoO_x-Pt/C and TiO_x-Pt/C catalysts was the direct four-electron process with the transfer of the first electron as the rate-determining step. The increase in catalytic activity for ORR on MoO_x-Pt/C and TiO_x-Pt/C catalysts, in comparison with Pt/C catalyst, was explained by synergetic effects due to the formation of the interface between the platinum and oxide materials and by spillover due to the surface diffusion of oxygen reaction intermediates.     

The PZT system (PbTixZr1−xO3, 0≤x≤1.0): The dependences of electrophysical properties of solid solutions on the electric field strength and component concentration (Part 5)

The physical properties of PZT (PbTi_xZr_1−xO₃, 0.0≤x≤1.0) ceramics were studied in broad ranges of constant and alternating electric field strengths (0 kV/cm≤E≤30 kV/cm). Dielectric, piezoelectric and elastic parameters of the solid solutions at room temperature were investigated. The results can be helpful to develop of PZT based materials for use in various high-voltage devices and bend components such as varactors, phase shifters, etc.     

Structural,vibrational, optical,magnetic and dielectric properties of Bi1−xBaxFeO3 nanoparticles

Bi_1−xBa_xFeO₃ (x=0.05, 0.10 and 0.15) nanoparticles were synthesized by the sol–gel method. X-ray diffraction and Raman spectroscopy results showed the presence of distorted rhombohedral structure of Bi_1−xBa_xFeO₃ nanoparticles. Rietveld refinement and Williamson–Hall plot of the x-ray diffraction patterns showed the increase in lattice parameters, unit cell volume and the particle size. Infrared spectroscopy and Raman analysis revealed the shifting of phonon modes towards the higher wavenumber side with increasing Ba concentration. These samples exhibited the optical band gap in the visible region (2.47–2.02 eV) indicating their ability to absorb visible light. Magnetic measurement showed room temperature ferromagnetic behavior, which may be attributed to the antiferromagnetic core and the ferromagnetic surface of the nanoparticles, together with the structural distortion caused by Ba substitution. The magnetoelectric coupling was evidenced by the observation of the dielectric anomaly in the dielectric constant and the dielectric loss near antiferromagnetic Neel temperature in all the samples.     

Structural and dielectric properties of Bi1−xSrxMnO3 (0.40≤x≤0.55)

In order to study the effect of Sr substitution on structural and dielectric properties of Bi_1−xSr_xMnO₃ (0.40≤x≤0.55) compounds were synthesized by the solid state reaction method. The as-prepared samples were characterized by X- ray diffraction (XRD) and dielectric measurements to correlate structural changes with dielectric properties. The XRD data were further analyzed by the Rietveld refinement. The highest dielectric constant was observed in Bi_0.55Sr_0.45MnO₃ and Bi_0.5Sr_0.5MnO₃ systems (∼10⁶) mainly because of orientation polarization. The charge ordering temperature decreases with increasing Sr concentration in Bi_1−xSr_xMnO₃ systems.     

Electrical conductivity and redox stability of La2Mo2−xWxO9 materials

A series of compounds La₂Mo_2−xW_xO₉ (x = 0-2) were synthesized using a freeze-dried precursor method at relatively low temperatures (673-823 K). These materials were characterised by thermogravimetric and differential thermal analysis (TG/DTA), differential scanning calorimetric (DSC), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and dilatometric measurements. Oxygen stoichiometry was evaluated by coulometric titration and thermogravimetric analysis at 873-1273 K. The ionic and electronic conductivities of these materials were analysed by impedance spectroscopy and a Hebb-Wagner ion-blocking method under moderately reducing conditions. The presence of W⁶⁺ leads to an increase of the stability range (about 10⁻¹⁶ Pa for La₂Mo_0.5W_1.5O₉ at 1073 K) and prevents oxygen loss and amorphisation. Within the stability range, the electronic conductivity increases gradually as the temperature increases and as the oxygen partial pressure reduces. This indicates that the electronic transport is mainly n-type as a result of the oxygen-content decreasing in the molybdate lattice. Further reduction of the oxygen partial pressure gave rise to the decomposition of La₂Mo_2−xW_xO₉, leading to the formation of new phases with molybdenum in lower oxidation states, which further enhances the electronic conductivity. The results of the coulometric titration and the thermogravimetric studies under a dry 5% H₂/Ar flow suggest that tungsten doped lanthanum molybdate materials can be used as electrolyte only at low temperature and under moderate reducing conditions.