Preparation and characterization of three dimensionally ordered macroporous Li4Ti5O12 anode for lithium batteries

Three dimensionally ordered macroporous (3DOM) Li₄Ti₅O₁₂ membrane (80 μm thick) was prepared by a colloidal crystal templating process. Colloidal crystal consisting of monodisperse polystyrene particles (1 μm diameter) was used as the template for the preparation of macroporous Li₄Ti₅O₁₂. A precursor sol consisting of titanium isopropoxide and lithium acetate was impregnated into the void space of template, and it was calcined at various temperatures. A macroporous membrane of Li₄Ti₅O₁₂ with inverse-opal structure was successfully prepared at 800 °C. The interconnected pores with uniform size (0.8 μm) were clearly observed on the entire part of membrane. The electrochemical properties of the three dimensionally ordered Li₄Ti₅O₁₂ were characterized with cyclic voltammetry and galvanostatic charge and discharge in an organic electrolyte containing a lithium salt. The 3DOM Li₄Ti₅O₁₂ exhibited a discharge capacity of 160 mA h g⁻¹ at the electrode potential of 1.55 V versus Li/Li⁺ due to the solid state redox of Ti^3+/4+ accompanying with Li⁺ ion insertion and extraction. The discharge capacity was close to the theoretical capacity (167 mA h g⁻¹), which suggested that the Li⁺ ion insertion and extraction took place at the entire part of 3DOM Li₄Ti₅O₁₂ membrane. The 3DOM Li₄Ti₅O₁₂ electrode showed good cycle stability.     

Hierarchical Li4Ti5O12 nanosheet arrays anchoring on carbon fiber cloth as ultra-stable free-standing anode of Li-ion battery

A flexible, free-standing composite anode with Li₄Ti₅O₁₂ nanosheet arrays anchoring on plain-weaved carbon fiber cloth (LTO@CC) is prepared by a hydrothermal and post-annealing process assisted by a TiO₂ seed layer. The LTO@CC anode free from polymeric binder and conducting agent exhibited much higher lithium storage capacity and cycling stability than the conventional slurry-processed electrode using the dandelion-like Li₄Ti₅O₁₂ microspheres prepared by the same hydrothermal process. A high specific capacity of 128.8 mA h g^?1 was obtained at a current rate of 30 C (1 C = 175 mA g^?1), and almost negligible capacity loses was observed when the cell was cycled at 10, 20 and 30 C each for 100 cycles. The carbon fiber matrix contributed to Li storage at low current rate, but the LTO nanosheet arrays have played the dominant role on the excellent rate capability. The improved electrochemical performance can be attributed to the synergetic effect between the hierarchical Li₄Ti₅O₁₂ nanosheet arrays and the carbon fiber matrix, which integrated short Li⁺ diffusion length, three-dimensional conductive architecture and well preserved structural integrity during the high rate and repeated charge-discharge measurements.     

Enhanced electrochemical performance of core-shell Li4Ti5O12/PTh as advanced anode for rechargeable lithium-ion batteries

A nanocomposite of Li₄Ti₅O₁₂ particles coated with polythiophene (PTh) was fabricated as advanced anode for rechargeable lithium-ion batteries. The conducting PTh layer was successfully coated on the surface of Li₄Ti₅O₁₂ through the in-situ oxidative polymerization method. Benefiting from the core-shell structure, specific capacities as high as 171.5, 168.2 and 151.1 mA h g⁻¹ at 0.2, 1 and 10 C are obtained in the Li₄Ti₅O₁₂/PTh composite. The electrochemical results also show that the Li₄Ti₅O₁₂/PTh exhibits remarkably improved cycling performance as compared with the Li₄Ti₅O₁₂ anode. Moreover, the charge-transfer resistance of Li₄Ti₅O₁₂/PTh electrode is much lower than that of the bare Li₄Ti₅O₁₂, revealing that the PTh coating can significantly increase the electron conductivity between the Li₄Ti₅O₁₂ particles. The excellent electrochemical performance of the as-fabricated Li₄Ti₅O₁₂/PTh composite can be ascribed to the PTh layer which can suppress the dissolution of active material into the LiPF₆ electrolyte and enhance the electron conductivity of Li₄Ti₅O₁₂ nanocrystals. Thus, the Li₄Ti₅O₁₂/PTh composite is an advanced anode for use in high performance lithium-ion batteries application.     

All-solid-state lithium battery with a three-dimensionally ordered Li1.5Al0.5Ti1.5(PO4)3 electrode

To fabricate all-solid-state Li batteries using three-dimensionally ordered macroporous Li_1.5Al_0.5Ti_1.5(PO₄)₃ (3DOM LATP) electrodes, the compatibilities of two anode materials (Li₄Mn₅O₁₂ and Li₄Ti₅O₁₂) with a LATP solid electrolyte were tested. Pure Li₄Ti₅O₁₂ with high crystallinity was not obtained because of the formation of a TiO₂ impurity phase. Li₄Mn₅O₁₂ with high crystallinity was produced without an impurity phase, suggesting that Li₄Mn₅O₁₂ is a better anode material for the LATP system. A Li₄Mn₅O₁₂/3DOM LATP composite anode was fabricated by the colloidal crystal templating method and a sol-gel process. Reversible Li insertion into the fabricated Li₄Mn₅O₁₂/3DOM LATP anode was observed, and its discharge capacity was measured to be 27 mA h g⁻¹. An all-solid-state battery composed of LiMn₂O₄/3DOM LATP cathode, Li₄Mn₅O₁₂/3DOM LATP anode, and a polymer electrolyte was fabricated and shown to operate successfully. It had a potential plateau that corresponds to the potential difference expected from the intrinsic redox potentials of LiMn₂O₄ and Li₄Mn₅O₁₂. The discharge capacity of the all-solid-state battery was 480 μA h cm⁻².     

Li ion conduction of perovskite Li0.375Sr0.4375Ti0.25Ta0.75O3 and related compounds

In this work, perovskite-structured Li_0.375Sr_0.4375M_0.25N_0.75O₃ (M=Ti, Sn, N=Nb, Ta) solid electrolytes were synthesized by conventional solid state reaction method. Phase compositions, fractured morphologies and conductivities of these compounds were investigated by X-ray diffraction, scanning electron microscope and AC-impedance spectroscopy, respectively. X-ray diffraction analysis confirms that all of Li_0.375Sr_0.4375M_0.25N_0.75O₃ (M=Ti, Sn, N=Nb, Ta) ceramics present perovskite structure. Pure Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Ta_0.75O₃ perovskite ceramics were obtained. But impurities were detected in Li_0.375Sr_0.4375Ti_0.25Nb_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Nb_0.75O₃. Among all investigated compounds, Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ shows the highest total ionic conductivity of 2.60 × 10^?4 S cm^?1 at room temperature and the lowest activation energy of 0.347 eV. Conductivities of Li_0.375Sr_0.4375Sn_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Sn_0.25Nb_0.75O₃ were 4.4 × 10^?5 S cm^?1 and 1.82 × 10^?6 S cm^?1, respectively. Their conductivities were much lower than Li_0.375Sr_0.4375Ti_0.25Ta_0.75O₃ and Li_0.375Sr_0.4375Ti_0.25Nb_0.75O₃.     

Hydrothermal synthesis of spherical Li4Ti5O12 material for a novel durable Li4Ti5O12/LiMn2O4 full lithium ion battery

Pure spherical Li₄Ti₅O₁₂ spinel material is quickly synthesized via an efficient hydrothermal procedure. The obtained Li₄Ti₅O₁₂ particle size is about 0.5 µm. The Li₄Ti₅O₁₂ has an initial discharge capacity of 162.2 mA h g⁻¹ and capacity retention of 97.5% after 100 cycles at a rate of 0.2 C. Then, a 2.5 V and long-lasting Li-ion cell with a LiMn₂O₄ cathode and a Li₄Ti₅O₁₂ anode is developed. Electrochemical measurements of the cell indicate that the Li₄Ti₅O₁₂/LiMn₂O₄ full cell, with a weight ratio of 1.5 between cathode and anode, exhibits excellent electrochemical performance, delivering a reversible capacity of 130 mA h g⁻¹ at room temperature. The full cell also exhibits outstanding electrochemical performances at high temperature, as it has an initial discharge capacity of 109.6 mA h g⁻¹, along with a capacity retention rate of 88.9% after 100 cycles at 55 °C.     

Improvement the electrochemical performance of Cr doped layered-spinel composite cathode material Li1.1Ni0.235Mn0.735Cr0.03O2.3 with Li4Ti5O12 coating

The Cr doped layered-spinel composite cathode material Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3 was synthesized and coated with different content of Li₄Ti₅O₁₂ by a sol–gel method. The materials were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM). The effect of Li₄Ti₅O₁₂ coatings on the electrochemical performance of the pristine material was evaluated from charge/discharge cycles, rate performance, and electrochemical impedance spectroscopy (EIS). The XRD results show that the lattice crystal and the content of spinel phase have been increased in the Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3 materials after Li₄Ti₅O₁₂ coating. The results from TEM and selected area electron diffraction (SAED) indicate that the Li₄Ti₅O₁₂ coating assumes a spinel structure on the Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3. The discharge capacities, cycling and rate performances of the Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3 materials in the first cycle are improved with the addition of Li₄Ti₅O₁₂. Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3 coated with 3 wt% Li₄Ti₅O₁₂ shows the highest discharge capacity (271.7 mA h g⁻¹), highest capacity retention (99.4% for 100 cycles), and best rate capability (132 mA h g⁻¹ at 10 C). EIS result indicates that the resistance of Li_1.1Ni_0.235Mn_0.735Cr_0.03O_2.3 electrode decreases with the addition of Li₄Ti₅O₁₂. The enhanced electrochemical performance can be ascribed to the increased spinel content, lower resistance and the enhanced lithium-ion diffusion kinetics.     

Preparation and capacitance performance of nitrided lithium titanate nanoarrays

Nitrided lithium titanate (N-Li₄Ti₅O₁₂) nanoarrays with nanowire and nanotube structures were designed as the electrode materials of lithium-ion supercapacitor for electrochemical energy storage. Two types of TiO₂ nanoarrays were used as the precursor which involved TiO₂ nanowire array prepared by hydrothermal process and TiO₂ nanotube array prepared by anodization process. Li₄Ti₅O₁₂ nanoarrays were formed through hydrothermal reaction or sonochemical reaction of TiO₂ nanoarrays with lithium hydroxide and then calcination treatment process. Finally, N-Li₄Ti₅O₁₂ nanoarrays were formed through nitriding treatment of Li₄Ti₅O₁₂ using ammonia as nitrogen source. The electroactive N-Li₄Ti₅O₁₂ nanowire array and nanotube array exhibited the specific capacitance of 607.2 F g⁻¹ and 814.4 F g⁻¹ at a current density of 1 A g⁻¹, respectively. The corresponding capacitance retention was determined to be 92.1% and 94.2% after 1000 cycles at high current density of 5 A g⁻¹. The corresponding capacitance still kept 182.9 and 352.1 F g⁻¹ at much higher current density of 20 A g⁻¹, presenting reasonable rate capability for N-Li₄Ti₅O₁₂ nanoarrays. The improved capacitance performance of N-Li₄Ti₅O₁₂ nanotube array was ascribed to the more amount of TiN and more accessible nanotube surface area, which contributed to the improved conductivity and fast diffusion of electrolyte ions on the surface of electrode. Both N-Li₄Ti₅O₁₂ nanowire array and nanotube array with well-aligned integrative structure exhibited an excellent cycling stability during continuous charge/discharge process. Well-designed N-Li₄Ti₅O₁₂ nanoarrays with high capacitance, good cycling stability and rate capability presented the promising application as feasible electrode materials of lithium-ion supercapacitors for the energy storage.     

Preparation of Li4Ti5O12 spherical particles for rechargeable lithium batteries

Spherical Li₄Ti₅O₁₂ particles were prepared via an emulsion-gel process. The preparation of spherical Li₄Ti₅O₁₂ such as the concentrations of the starting materials and heat treatment were optimized. The particle size distribution of the Li₄Ti₅O₁₂ prepared under optimized condition was very narrow, and the particle size was 0.45 μm. It was found that a short heat treatment in an infrared furnace was useful to crystallize amorphous LiTiO powders without aggregation of particles or morphology change. The obtained Li₄Ti₅O₁₂ had the spinel structure, and was phase pure. The prepared Li₄Ti₅O₁₂ exhibited a high discharge capacity of 160 mA h g⁻¹ at the potential of 1.5 V versus Li/Li⁺, and the charge–discharge cycle stability was excellent.     

Synthesis and electrochemical properties of La-doped Li4Ti5O12 as anode material for Li-ion battery

La-doped Li₄Ti₅O₁₂ was successfully synthesized from Li₂CO₃, La₂O₃ and tetrabutyl titanate by a simple ball milling assisted modified solid-state method. The impact of La-doping on crystalline structure, particle size, morphology and electrochemical performance of Li₄Ti₅O₁₂ was investigated. The samples were characterized by XRD, SEM, galvanostatically charge–discharge and electrochemical impedance spectroscopy. The results demonstrated that the in-situ coated and ball-milling method could decrease the particle size and prevent the aggregation of Li₄Ti₅O₁₂. La-doping obviously improved the rate capability of Li₄Ti₅O₁₂ via the generation of less electrode polarization and higher electronic conductivity. Li_3.95La_0.05Ti₅O₁₂ exhibited a relatively excellent rate capability and cycling stability. At the charge–discharge rate of 0.5 C and 40 C, its discharge capacities were 176.8 mAh/g and 54.7 mAh/g. After 10 cycles, fairly stable cycling performance was achieved without obvious capacity fade at 0.5 C, 1 C, 2 C, 5 C, 10 C, 20 C and 40 C. In addition, compared to Li₄Ti₅O₁₂, Li_3.95La_0.05Ti₅O₁₂ almost did not have the initial capacity loss. It indicated that Li_3.95La_0.05Ti₅O₁₂ was a promising candidate material for anodes in Li-ion battery application.     

Facile synthesis and electrochemical performance of nitrogen-doped porous hollow coaxial carbon fiber/Co3O4 composite

Economy and efficiency are two important indexes of lithium-ion batteries (LIBs) materials. In this work, nitrogen doped hollow porous coaxial carbon fiber/Co₃O₄ composite (N-PHCCF/Co₃O₄) is fabricated using the fibers of waste bamboo leaves as the template and carbon resource by soaking and thermal treatment, respectively. The N-PHCCF/Co₃O₄ exhibits an outstanding electrochemical performance as anode material for lithium ion batteries, due to the nitrogen doping, coaxial configuration and porous structure. Specifically, it delivers a high discharge reversible specific capacity of 887 mA h g^?1 after 100 cycles at the current density of 100 mA g^?1. Furthermore a high capability of 415 mA h g^?1 even at 1 A g^?1 is exhibited. Most impressively, the whole process is facile and scalable，exhibiting recycling of resource and turning waste into treasure in an eco-friendly way.     

Synthesis and electrochemical performance of Li4Ti5O12/C composite by a starch sol assisted method

Li₄Ti₅O₁₂/C composite anode materials were synthesized by a simple starch sol assisted method using TiO₂-anatase and Li₂CO₃ as raw materials and soluble starch as carbon source. The influences of calcination temperature and starch amounts on the microstructure and electrochemical performance were systematically investigated. The samples were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and constant-current charge/discharge cycling tests. The results showed that the Li₄Ti₅O₁₂/C composite with 10 wt.% starch synthesized at 800 °C for 6 h had homogeneous particle size distribution with an average particle size of 200–300 nm and exhibited the optimal electrochemical performance with specific discharge capacities of 168.5, 160.8, 155.1 and 141.8 mAh g^? 1 at 0.2 °C, 1 °C, 2 °C and 5 °C rates, respectively, and satisfactory cycling stability. It could be attributed to the homogeneous ultrafine particles and in situ carbon coating, which enhanced the electronic conductivity and diffusion of lithium ions in the electrode.     

Ag enhanced electrochemical performance for Na2Li2Ti6O14 anode in rechargeable lithium-ion batteries

Due to the characteristics of an electronic insulator, Na₂Li₂Ti₆O₁₄ always suffers from low electronic conductivity as anode material for lithium storage. Via Ag coating, Na₂Li₂Ti₆O₁₄@Ag is fabricated, which has higher electronic conductivity than bare Na₂Li₂Ti₆O₁₄. Enhancing the Ag coating content from 0.0 to 10.0 wt%, the surface of Na₂Li₂Ti₆O₁₄ is gradually deposited by Ag nanoparticles. At 6.0 wt%, a continuous Ag conductive layer is formed on Na₂Li₂Ti₆O₁₄. While, particle growth and aggregation take place when the Ag coating content reaches 10.0 wt%. As a result, Na₂Li₂Ti₆O₁₄@6.0 wt% Ag displays better cycle and rate properties than other samples. It can deliver a lithium storage capacity of 131.4 mAh g⁻¹ at 100 mA g⁻¹, 124.9 mAh g⁻¹ at 150 mA g⁻¹, 119.1 mAh g⁻¹ at 200 mA g⁻¹, 115.8 mAh g⁻¹ at 250 mA g⁻¹, 111.9 mAh g⁻¹ at 300 mA g⁻¹ and 109.4 mAh g⁻¹ at 350 mA g⁻¹, respectively.     

Study of structure and conductivity of Li3/8Sr7/16-3x/2LaxZr1/4Nb3/4O3 solid electrolytes

Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0, 0.05, 0.10, 0.15, 0.20) were synthesized using the conventional solid-state reaction method. In order to increase the vacancy concentration, La³⁺ was doped on the Sr²⁺ site. Crystal structures of doped samples were characterized by X-ray diffraction. Except, perovskite-type Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0, 0.05, 0.10, 0.15) samples were fabricated by heat treatment at 1250 °C, 1275 °C, 1275 °C and 1275 °C, respectively, for 15 h. Lattice sizes decreased with the increase of doping amounts because of the smaller ion radius of La³⁺ compared to that of Sr²⁺. Ionic conductivities of the samples were measured by AC impedance spectroscopy. The results showed that the ionic conductivity increases at first and then decreases with raising doping amounts and sintering temperatures. So the optimized composition Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0.05) sintered at 1275 °C was selected with the highest total conductivity of 3.33 × 10^?5 S cm^?1at 30 °C and an activation energy of 0.27 eV. Additionally, potentiostatic polarization test was used to evaluate the electronic conductivity. The optimal composition Li_3/8Sr_7/16-3x/2La_xZr_1/4Nb_3/4O₃ (x = 0.05) as a possible Li-ion conducting solid electrolyte has an electronic conductivity of only 8.39 × 10^?9 S cm^?1.     

Investigation on the anti-reduction mechanism of Ti4+ in high dielectric constant system Ca0.9La0.067TiO3 by doping with Al2O3

Ca_0.9La_0.067TiO₃ (abbreviated as CLT) ceramics doped with different amount of Al₂O₃ were prepared via the solid state reaction method. The anti-reduction mechanism of Ti⁴⁺ in CLT ceramics was carefully investigated. X-ray diffraction (XRD) was used to analyze the phase composition and lattice structure. Meanwhile, the Rietveld method was taken to calculate the lattice parameters. X-ray photoelectron spectroscopy (XPS) was employed to study the valence variation of Ti ions in CLT ceramics without and with Al₂O₃. The results showed that Al³⁺ substituted for Ti⁴⁺ to form solid solution and the solid solubility limit of Al³⁺ is near 1.11 mol%. Furthermore, the reduction of Ti⁴⁺ in CLT ceramics was restrained by acceptor doping process and the Q × f values of CLT ceramics were improved significantly. The CLT ceramic doped with 1.11 mol% Al₂O₃ exhibited good microwave dielectric properties: ε_r = 141, Q × f = 6848 GHz, τ_f = 576 ppm/°C.     

Improving the electrochemical performance of Li4Ti5O12/Ag composite by an electroless deposition method

Nano-sized silver particle (<20 nm) was highly dispersed on the surface of Li₄Ti₅O₁₂ particles by an electroless deposition method. The Ag additive played a positive role in improving the electrical contact between Li₄Ti₅O₁₂ particles and the current collector and therefore improved the high rate capacity of Li₄Ti₅O₁₂, but it did not take part in the electrochemical reactions with Li⁺ in Li₄Ti₅O₁₂/Ag composite during the cycling. The experimental results showed that the smaller the silver particles and the more homogeneous dispersion of silver particles in the Li₄Ti₅O₁₂ matrix, the better the cycling performance we obtained.     

Synthesis and electrochemical performance of Li4Ti5O12/Ag composite prepared by electroless plating

To improve the electrochemical and anti flatulence performance of Li₄Ti₅O₁₂, Ag modified Li₄Ti₅O₁₂ (LTO) with high electrochemical performance as anode materials for lithium-ion battery was synthesized successfully by two-step solid phase sintering and subsequent electroless plating process in the presence of silver. The effect of Ag modification on the physical and electrochemical properties were investigated by the extensive material characterization of X-ray diffraction (XRD), Raman spectroscopy, scanning electron microscopy (SEM). The results showed that the samples possessed single spinel structure, it could be observed that the LTO/Ag composite and the pure LTO shared the same vibration frequencies, which indicated that the crystal structure of LTO didn’t change after electroless plating process, and the particles were uniformly and regularly shaped within 0.5–1.0 µm. Electrochemical performance of the samples were evaluated by the charging and discharging, cyclic voltammetry, electrochemical impedance spectroscopy, cycling and rate tests. It's obvious that the LTO/Ag composite prepared at the 10 min of electroless plating showed the highest performance with capacitance of 182.3 mA h/g at 0.2 C current rates. What's more, the LTO/Ag composites still maintained 92% of its initial capacity even after 50 charge/discharge cycles. Modification of appropriate Ag not only benefits the reversible intercalation and deintercalation of Li⁺, but also improves the diffusion coefficient of lithium ion. Besides, modification of appropriate Ag lower electrochemical polarization leads to higher conductivity and cycle performance of LTO, which is consistent with the results of the best reversible capacities.     

Combustion synthesis of high-performance Li4Ti5O12 for secondary Li-ion battery

Spinel Li₄Ti₅O₁₂ was synthesized by a simple glycine-nitrate auto-combustion by applying aqueous medium and constricting the reactions in the pores of cellulose fibers. The products from the auto-combustion and further calcination at various temperatures were characterized by XRD, SEM, BET surface area and TEM examinations. Pure phase and well-crystallized nano-Li₄Ti₅O₁₂ oxides were obtained at a calcination temperature of 700 °C or higher. The 700 °C calcined one shows the best and high electrochemical performance, which reached a capacity of ～125 mAh/g at 10 C discharge rate with fairly stable cycling performance even at 40 °C. Electrochemical impedance spectroscopy tests demonstrated that the surface reaction kinetics of Li₄Ti₅O₁₂ was improved significantly with the increase of its electronic conductivity.     

Investigation of Li5Cr7Ti6O25 as novel anode material for high-power lithium-ion batteries

In this work, Li₅Cr₇Ti₆O₂₅ as a new anode material for rechargeable batteries is fabricated through a simple sol-gel method at different calcination temperatures. The X-ray diffraction, scanning electron microscopy, high resolution transmission electron microscopy, charge/discharge curve and cyclic voltammograms are utilized to study the crystal structures, morphologies and electrochemical properties of as-obtained Li₅Cr₇Ti₆O₂₅ samples. The impact of calcination temperatures on morphologies and electrochemical properties of Li₅Cr₇Ti₆O₂₅ is discussed in detail. The test result shows that the 800 °C is a proper calcination temperature for Li₅Cr₇Ti₆O₂₅ with excellent electrochemical properties. Cycled at 200 mA g⁻¹, it displays a high initial reversible capacity of 146.6 mA h g⁻¹ and retains a considerable capacity of 130.8 mA h g⁻¹ after 300 cycles. Even cycled at large current density of 500 mA g⁻¹, the initial reversible capacity of 129.6 mA h g⁻¹ with the capacity retention of 88% after 300 cycles is achieved, which is obviously higher than that of Li₅Cr₇Ti₆O₂₅ prepared at 700 °C (80.5 mA h g⁻¹ and 68%) and 900 °C (98.4 mA h g⁻¹ and 80%). In addition, in-situ XRD analysis reveals that Li₅Cr₇Ti₆O₂₅ exhibits a reversible structural change during lithiation and delithiation processes. The above prominent electrochemical performance indicates the great potential of the Li₅Cr₇Ti₆O₂₅ obtained at 800 °C as anode material for rechargeable batteries.     

Polymer microsphere-assisted synthesis of lithium-rich cathode with improved electrochemical performance

The Li-rich layered cathode material Li_1.165Mn_0.501Ni_0.167Co_0.167O₂ with porous structure has been successfully synthesized through a facile co-precipitation approach followed with a high-temperature calcination treatment, adopting polymer microsphere (PSA) as a template and conductive agent. The PSA-assisted Li_1.165Mn_0.501Ni_0.167Co_0.167O₂ composite exhibits remarkably improved cycling stability and rate capability compared with the bare composite. It delivers a high initial discharge capacity of 267.0 mA h g⁻¹ at 0.1 C (1 C=250 mA g⁻¹) between 2.0 V and 4.65 V. A discharge capacity of 214.9 mA h g ⁻¹ is still obtained after 100 cycles. Furthermore, the diffusion coefficients of Li⁺ investigated by the cyclic voltammetry technique are approximately 10⁻¹⁵–10⁻¹⁴ cm² s⁻¹. Such outstanding performance is mainly ascribed to: on one hand, the carbon residue of PSA after being calcined at high temperature contributes to enhance the electronic conductivity of the electrode and alleviates the volume changes during the Li⁺-insertion/extraction, leading to an improved rate capability; on the other hand, the unique porous structure and small particle size are conductive to increase the exposed electrochemical active surface, shorten Li⁺ diffusion distance and thus enhance the lithium storage capacity.