One‐dimensional heat transfer study of a fiber‐reinforced wind epoxy composite system in vacuum assisted resin transfer molding process

To investigate the influence of curing behavior of a wind‐epoxy resin in vacuum assisted resin transfer molding (VARTM) process, numerical analysis of the heat transfer study of VARTM process was established to characterize temperature distribution in one dimension by directly solving heat equation and was compared with the result of experiment. Differential scanning calorimeter (DSC) was applied to test curing kinetic parameters of the epoxy system, which was required to evaluate internal thermal source and analyze heat transfer equations. Two models, such as nth order curing model and autocatalytic model, were established to solve the heat transfer equation. Combining the theoretical results with nth order curing model and experiment, it can be known that in early stage, temperature distribution correlates well with the experiment results due to the dominant chemical‐controlled reaction, while great discrepancy appears in the latter stage due to diffusion‐controlled reaction taking over. The result of the heat equation solved by autocatalytic model correlates well with the experiment results. POLYM. COMPOS., 35:1031–1037, 2014. © 2013 Society of Plastics Engineers     

Use of eco‐friendly epoxy resins from renewable resources as potential substitutes of petrochemical epoxy resins for ambient cured composites with flax reinforcements

In the last years, some high renewable content epoxy resins, derived from vegetable oils, have been developed at industrial level and are now commercially available; these can compete with petroleum‐based resins as thermoset matrices for composite materials. Nevertheless, due to the relatively high cost in comparison to petroleum‐based resins, their use is still restricted to applications with relatively low volume consumption such as model making, tuning components, nautical parts, special effects, outdoor sculptures, etc. in which, the use of composite laminates with carbon, aramid and, mainly, glass fibers is generalized by using hand layup and vacuum assisted resin transfer molding (VARTM) techniques due to low manufacturing costs and easy implementation. In this work, we study the behavior of two high renewable content epoxy resins derived from vegetable oils as potential substitutes of petroleum‐based epoxies in composite laminates with flax reinforcements by using the VARTM technique. The curing behavior of the different epoxy resins is compared in terms of the gel point and exothermicity profile by differential scanning calorimetry (DSC). In addition, overall performance of flax‐epoxy composites is compared with standardized mechanical (tensile, flexural and impact) and thermal (Vicat softening temperature, heat deflection temperature, thermo‐mechanical analysis) tests. The curing DSC profiles of the two eco‐friendly epoxy resins are similar to a conventional epoxy resin. They can be easily handled and processed by conventional VARTM process thus leading to composite laminates with flax with balanced mechanical and thermal properties, similar or even higher to a multipurpose epoxy resin. POLYM. COMPOS., 2012. © 2012 Society of Plastics Engineers     

Elevated‐temperature vacuum‐assisted resin transfer molding process for high performance aerospace composites

Vacuum‐assisted resin transfer molding (VARTM) is commonly used for general temperature applications (<150 °C) such as boat hulls and secondary aircraft structures. With growing demands for applications of composites in elevated temperature environments, significant cost savings can be achieved by employing the VARTM process. However, implementation of the VARTM process for fabricating elevated temperature composites presents unique challenges such as high porosity and low fiber volume contents. In the present work, a low cost and reliable VARTM process is developed to manufacture elevated temperature composites for aerospace applications. Modified single vacuum bagging infusion and double vacuum bagging infusion processes were evaluated. Details of the method to obtain high quality composite parts and the challenging issues related to the manufacturing process are presented. Density and fiber volume fraction testing of manufactured panels showed that high quality composite parts with void content less than 1% have been consistently manufactured. A property database of the resin system and the composites was developed. A three‐dimensional mathematical model has also been developed for flow simulation and implemented in the ABAQUS finite element package code to predict the resin flow front during the infusion process and to optimize the flow parameters. The results of the present study indicate that aircraft grade composite parts with high fiber volume fractions can be manufactured using the developed elevated temperature VARTM process. © 2013 Society of Chemical Industry     

Numerical investigation on flow through porous media in the post‐infusion process

During the vacuum‐assisted resin transfer molding (VARTM) processing, the post‐infusion behavior after complete wet‐out and before gelation of the resin is critical for the development of the thickness and fiber volume fraction distribution in the cured composite part. The pressure gradient developed during infusion results in a thickness gradient due to the flexible nature of the bagging approach. After full infusion, the resin typically bleeds into a vacuum trap, allowing redistribution of pressure and preform thickness. In this study, a non‐rigid control volume is used to formulate a set of governing equations for analysis of the post‐infusion process. The model is used to investigate the effects of processing parameters and different processing scenarios on resin flow, resin pressure, and thickness variation of the composite laminate. This work provides a tool for optimization of the VARTM process to reduce final part variability. POLYM. COMPOS., 2009. © 2008 Society of Plastics Engineers     

VARTM用EP体系流变特性及固化工艺的研究

研究了真空辅助树脂传递模塑(VARTM)工艺用环氧树脂(EP)体系的流变特性,结合差示扫描量热(DSC)仪和旋转式粘度计对A1、A2、A3三种EP体系的测试结果,确定A2树脂体系适合于VARTM工艺,并根据双阿累尼乌斯方程,建立了A2树脂体系的流变模型。该模型可以预测树脂在不同温度下的粘度特性,为合理制定工艺参数提供了重要依据。用DSC仪对A2树脂体系的固化反应过程进行分析,利用外推法确定了固化工艺参数。     

Vacuum‐assisted resin transfer molding using tackified fiber preforms

A low cost composite fabrication process—tackified SCRIMP—is described for fabricating aerospace‐grade composites based on tackification and vacuum‐assisted resin transfer molding (VARTM). Tackification based on a commercial tackifier (FT 500 from 3M) was used to make the net‐shape fiber preform. It was found that tackifier concentration and application conditions play important roles in governing the moldability of tackified fiber preforms. An epoxy resin (PR 500 from 3M) was used in the VARTM process‐SCRIMP at high temperatures. Experimental results show that composites with high fiber content (> 60% by volume) can be manufactured at low cost using tackification. Effects of tackification methods on composite dimension control, void content and mechanical properties were investigated and compared in both RTM and SCRIMP.     

Modeling of resin infusion in vacuum assisted resin transfer molding

Resin infusion was modeled and analytic solutions were obtained for vacuum assisted resin transfer molding (VARTM). Compaction behavior of the fiber preform was examined experimentally and the influence of compressibility of the preform on the resin infusion was investigated mathematically. Flow front advancement through the preform was predicted by the analytic model proposed in the present study. The model provided pressure and thickness distributions of the region impregnated by the resin. For verification of the analytic solutions, a resin infusion experiment and a mold filling simulation for VARTM were performed and compared with the analytic ones. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers.     

Effects of the addition of a cover mold on resin flow and the quality of the finished product in vacuum‐assisted resin transfer molding

For vacuum‐assisted resin transfer molding (VARTM), we propose adding a cover mold, inserted between the distribution medium and the peel ply, to achieve a higher fiber volume fraction in the final product. As the conventional VARTM process does not use a cover mold, improved processes using different rigid covers were explored. A three‐dimensional digital image correlation system was developed to monitor the thickness evolution of the vacuum package during the infusion stage. This system was validated as a full‐field displacement test. The results demonstrate that there are three advantages to using a cover mold. First, in the filling stage, a rigid cover mold can prevent shrinkage of the part at the resin flow front, and even cause slight expansion of the unsaturated part. This improves the resin flow and shortens the time required for complete infusion. Second, a cover mold can limit the amount of excess resin needed to infuse the saturated part. Third, in the postfilling stage, the cover mold can be used to accelerate extrusion of the excess resin in the package. The overall effect is to increase the fiber volume fraction in the final product. POLYM. COMPOS., 37:1435–1442, 2016. © 2014 Society of Plastics Engineers     

Vacuum‐assisted resin transfer molding model

A model of the vacuum‐assisted resin transfer molding (VARTM) process is developed that includes the most important aspects of the processing physics. The model consists of several submodels, such as preform mechanics, Darcy flow, wicking flow, and void formation. The preform mechanics model treats the preform as a linearly elastic, one‐dimensional (1D) solid. However, the key physical process is the lubrication of the preform due to fluid wetting, and this is modeled as a reduction in preform modulus, an easily measurable parameter. Residual stress, three‐dimensional (3D) structural behavior, and nonlinearity are neglected, but can all be included. The fluid flow model of capillary wicking is not tacked onto the Darcy equation as a modified boundary condition, as was previously done. The wicking is treated simply, but more realistically, by performing a force balance on the fluid in a pore. Balancing the capillary pressure and the viscous drag allows the development of a wicking front that precedes the main Darcy flow front to an extent that depends on several easily measurable factors. It is this wicking front that is responsible for the small void formation that reduces the quality of VARTM parts, relative to resin transfer molding (RTM) parts. POLYM. COMPOS. 26:477–485, 2005. © 2005 Society of Plastics Engineers     

Resin infusion of triaxially braided preforms with through‐the‐thickness reinforcement

Vacuum assisted resin transfer molding (VARTM) has shown potential to significantly reduce the manufacturing cost of high‐performance aerospace composite structures. In this investigation, high fiber volume fraction, triaxially braided preforms with through‐the‐thickness stitching were successfully resin infiltrated by the VARTM process. The preforms, resin infiltrated with three different resin systems, produced cured composites that were fully wet‐out and void free. A three‐dimensional finite element model was used to simulate resin infusion into the preforms. The predicted flow patterns agreed well with the flow patterns observed during the infiltration process. The total infiltration times calculated using the model compared well with the measured times.     

Influence of alcohol pre‐infusion on the quality of VARTM composites

In the vacuum assisted resin transfer molding (VARTM) process, part‐to‐part variations such as the uncertainty in the permeability and race tracking phenomenon make it difficult to achieve consistent mold filling and ensure part quality of composites. Alcohol pre‐infusion was presented in this study as a novel real‐time monitoring and control approach for the flow process in the VARTM process, alcohol test fluid is infused before the actual resin infusion to locate the potential dry spots without using the large quantity of sensors. Then corresponding process control strategy is designed, such as opening the auxiliary gate at specific moment on those predicted dry spot locations to compensate flow defects. Moreover, alcohol can be easily removed by heat without changing the local permeability. The influence of alcohol pre‐infusion on the quality of VARTM composites were investigated in this study. The mechanical tests were conducted to verify that the alcohol pre‐infusion approach has no significant effect on composite properties because alcohol can be removed from fiber by heat and air flow. Specifically, DMA, TGA, and FTIR spectrum proved that negligible difference existed on the resin–fiber interface between the composites with or without alcohol pre‐infusion. Finally, the microscopy results revealed a similar failure path in a resin matrix. TMA results also demonstrated similar dimension stability. This alcohol pre‐infusion approach was effective when compared with computer simulation and could eliminate the occurrence of dry spots and voids without using sensors or data‐acquisition system. The control schemes were shown in a case study to be capable of compensating the flow defects and achieving desired fill patterns in the face of permeability uncertainty. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

泡沫夹芯结构板泡沫壁流道内的流动特性

沟槽型真空辅助树脂传递模塑成型工艺（VARTM）是一种新型的泡沫夹芯结构板成型方法,利用实验探明了泡沫夹芯结构板芯材上不可渗泡沫壁流道内的流动行为。实验结果表明,液体在泡沫壁流道的流动能力大幅降低,只有光滑壁流道的60%左右,泡沫壁流道的粗糙内表面是造成这种现象的主要原因。提出了相应的压力驱动流动方程,并采用等效渗透率来表征液体在泡沫壁流道内的流动能力,得到了考虑粗糙表面影响的等效渗透率计算公式,提出了一个正确计算不可渗泡沫壁流道内流动的处理方法。     

Flow front measurements and model validation in the vacuum assisted resin transfer molding process

Through‐thickness measurements were recorded to experimentally investigate the through thickness flow and to validate a closed form solution of the resin flow during the vacuum assisted resin transfer molding process (VARFM). During the VART'M process, a highly permeable distribution medium is incorporated into the preform as a surface layer and resin is inftised Into the mold, under vacuum. During Infusion, the resin flaws preferentially across the surface and simultaneously through the thickness of the preform, giving rise to a three dimensional‐flow front. The time to fill the mold and the shape of the flow front, which plays a key role in dry spot formation, are critical for the optimal manufacture of large composite parts. An analytical model predicts the flow times and flow front shapes as a function of the properties of the preform, distribution media and resin. It was found that the flow front profile reaches a parabolic steady state shape and the length of the region saturated by resin is proportional to the square root of the time elapsed. Experimental measurements of the flow front in the process were carried out using embedded sensors to detect the flow of resin through the thickness of the preform layer and the progression of flow along the length of the part. The time to fill the part, the length of flow front and its shapes show good agreement between experiments and the analytical model. The experimental study demonstrates the need for control and optimization of resin injection during the manufacture of large parts by VARTM.     

Modeling of filtration through multiple layers of dual scale fibrous porous media

Functionally graded composites exhibit properties within the material that vary gradually without a recognizable boundary. One technique to manufacture functionally graded polymer composites is by liquid composite molding process. In this process, structural fabric layers are stacked in a closed mold and resin is injected into the mold. Particles may be added to the resin to tailor the properties of the final product. The structural fabrics typically consist of yarns or bundles of thousands of micron size fibers woven, stitched, or knitted together, which gives rise to a bimodal distribution of pore sizes; the larger pores in between the bundles and smaller ones within the bundles. The filtration process that takes place during infusion alters the flow resistance of the porous media and complicates the impregnation process. In this study, a vacuum‐assisted resin transfer molding (VARTM) process‐based approach is presented that enables functional grading in composites to obtain a desired distribution in properties. A model of the filtration phenomenon is proposed to predict the concentration distribution of particles within the dual scale fibrous porous media infused under a constant pressure drop. The approach uses Darcy's law and accounts for lowering of the permeability value due to the particle entrapment in the available pores. Experiments are conducted and the concentration of the particles in the fabric is measured. The results compare well with the predictions despite many assumptions made in the model. Nondimensional analysis and parametric study reveals the influence of critical parameters on the final particles concentration gradient. POLYM. COMPOS. 27:570–581, 2006. © 2006 Society of Plastics Engineers     

Modeling and analysis of thickness gradient and variations in vacuum‐assisted resin transfer molding process

As vacuum‐assisted resin transfer molding (VARTM) is being increasingly used in aerospace applications, the thickness gradient and variation issues are gaining more attention. Typically, thickness gradient and variations result from the infusion pressure gradient during the process and material variations. Pressure gradient is the driving force for resin flow and the main source of thickness variation. After infusion, an amount of pressure gradient is frozen into the preform, which primarily contributes to the thickness variation. This study investigates the mechanism of the thickness variation dynamic change during the infusion and relaxing/curing processes. A numerical model was developed to track the thickness change of the bagging film free surface. A time‐dependent permeability model as a function of compaction pressure was incorporated into an existing resin transfer molding (RTM) code for obtaining the initial conditions for relaxing/curing process. Control volume (CV) and volume of fluid (VOF) methods were combined to solve the free surface problem. Experiments were conducted to verify the simulation results. The proposed model was illustrated with a relatively complex part. POLYM. COMPOS., 2008. © 2008 Society of Plastics Engineers     

Damage evolution in low velocity impacted unreinforced vinyl ester 411‐350 and 411‐C50 resin systems

Damage evolution in plaques made of vinyl ester resin systems was investigated as a function of specimen thickness, impact energy level and matrix material. Dow DERAKANE vinyl ester 411‐350 and 411‐C50 resin systems, which have low viscosity and are ideally suited for low‐cost liquid processing techniques like vacuum assisted resin transfer molding (VARTM), were considered for the low velocity instrumented impact testing. Characterization of damage evolution was undertaken using optical microscopy and analysis of impact load histories recorded during the impact event. Radial cracking, perforations at the point of impact (in the form of a truncated cone), and damage resulting from the support constraints were identified as the dominant failure characteristics in both resin systems. Radial cracking, which originated from the bottom surface, was operative in all failed specimens and was attributed to the catastrophic failure due to extensive flexural tensile strength losses. For specimens that could deflect significantly, radial cracking and support‐constraint‐induced damage were the operative failure mechanisms. Radial cracking and through‐thickness shearing led to failure in stiffer plaques. The DERAKANE 411‐350‐vinyl ester resin system was found more damage resistant than the 411‐C50 system.     

Reduction of void content of vacuum‐assisted resin transfer molded composites by infusion pressure control

Vacuum‐assisted resin transfer molding is a promising technique for making large and complex composite structures. However, void formation remains a problem. Two primary contributors to void formation, non‐uniform resin flow and continuous evaporation of resin under low pressure, were experimentally studied. Improved pressure control at the vent is proposed to reduce the void content of the manufactured composite material: at the start of the resin infusion, the pressure at the vent is set to the full vacuum of the equipment, while after the resin has saturated all of the reinforcements, the pressure at the vent is increased slightly. The full vacuum at the start of infusion avoids air entrapment, and the slightly higher pressure later in the process restrains the resin evaporation. A lower void content is obtained. POLYM. COMPOS., 36:1629–1637, 2015. © 2014 Society of Plastics Engineers     

Simulation and validation of resin flow during manufacturing of composite panels containing embedded impermeable inserts with the VARTM process

Modern composite materials are becoming more and more advanced as engineers are better able to take advantage of their properties. In addition to their lighter weight and net‐shape manufacturing, current interest is to make these materials multifunctional. This may require one to insert various objects into the composite to achieve a variety of different goals. It is important to understand how these embedded objects will affect both the manufacturing and the structural integrity of the component. In this work, the effects of impermeable embedded inserts on the infusion stage of vacuum‐assisted resin transfer molding (VARTM) will be explored. In VARTM, one places a distribution media on top of the preform to aid the filling as the resin will first fill the face of the preform in contact with the distribution media and will then infuse the preform in the thickness direction. However, if one has an embedded impermeable insert in the thickness direction, it will obstruct the flow in the region below the embedded object. Several case studies are conducted to understand the effect of the geometry and placement of the embedded insert and the distribution media lay out and properties on the impregnation of the resin into the fiber preform. Finally, an approach is outlined to modify the layout of the distribution media in order to ensure a complete saturation of the preform under all but the most extreme conditions. The approach is validated with experiments. POLYM. COMPOS., 28:442–450, 2007. © 2007 Society of Plastics Engineers     

Electrospinning core‐shell nanofibers for interfacial toughening and self‐healing of carbon‐fiber/epoxy composites

This article reports a novel hybrid multiscale carbon‐fiber/epoxy composite reinforced with self‐healing core‐shell nanofibers at interfaces. The ultrathin self‐healing fibers were fabricated by means of coelectrospinning, in which liquid dicyclopentadiene (DCPD) as the healing agent was enwrapped into polyacrylonitrile (PAN) to form core‐shell DCPD/PAN nanofibers. These core‐shell nanofibers were incorporated at interfaces of neighboring carbon‐fiber fabrics prior to resin infusion and formed into ultrathin self‐healing interlayers after resin infusion and curing. The core‐shell DCPD/PAN fibers are expected to function to self‐repair the interfacial damages in composite laminates, e.g., delamination. Wet layup, followed by vacuum‐assisted resin transfer molding (VARTM) technique, was used to process the proof‐of‐concept hybrid multiscale self‐healing composite. Three‐point bending test was utilized to evaluate the self‐healing effect of the core‐shell nanofibers on the flexural stiffness of the composite laminate after predamage failure. Experimental results indicate that the flexural stiffness of such novel self‐healing composite after predamage failure can be completely recovered by the self‐healing nanofiber interlayers. Scanning electron microscope (SEM) was utilized for fractographical analysis of the failed samples. SEM micrographs clearly evidenced the release of healing agent at laminate interfaces and the toughening and self‐healing mechanisms of the core‐shell nanofibers. This study expects a family of novel high‐strength, lightweight structural polymer composites with self‐healing function for potential use in aerospace and aeronautical structures, sports utilities, etc. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermomechanical properties of alkali treated jute‐polyester/nanoclay biocomposites fabricated by VARTM process

A systematic study was carried out to investigate the effect of alkali treatment and nanoclay on thermomechanical properties of jute fabric reinforced polyester composites (JPC) fabricated by the vacuum‐assisted resin transfer molding (VARTM) process. Using mechanical mixing and sonication process, 1% and 2% by weight montmorillonite K10 nanoclay were dispersed into B‐440 premium polyester resin to fabricate jute fabric reinforced polyester nanocomposites. The average fiber volume was determined to be around 40% and void fraction was reduced due to the surface treatment as well as nanoclay infusion in these biocomposites. Dynamic mechanical analysis (DMA) revealed enhancement of dynamic elastic/plastic responses and glass transition temperature (T_g) in treated jute polyester composites (TJPC) and nanoclay infused TJPC compared with those of untreated jute polyester composites (UTJPC). Alkali treatment and nanoclay infusion also resulted in enhancement of mechanical properties of JPC. The maximum flexural, compression, and interlaminar shear strength (ILSS) properties were found in the 1 wt % nanoclay infused TJPC. Fourier transform‐infrared spectroscopy (FT‐IR) revealed strong interaction between the organoclay and polyester that resulted in enhanced thermomechanical properties in the composites. Lower water absorption was also observed due to surface treatment and nanoclay infusion in the TJPC. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013