Morphology,biodegradability, mechanical,and thermal properties of nanocomposite films based on PLA and plasticized PLA

In this study, melt intercalation method is applied to prepare poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG)‐plasticized PLA nanocomposite films including 0, 3, and 5% organoclay (Cloisite 30B) using a laboratory scale compounder, which is connected to a microcast film device. To evaluate the nanomorphology and the dispersion state of the clays, X‐ray diffraction (XRD) and transmission electron microscopy (TEM) are conducted. Tensile tests are performed to characterize the mechanical behavior of the films. Biodegradation rate is determined by degradation tests in composting medium. Differential scanning calorimeter (DSC) is applied to observe the thermal behavior of the films. XRD and TEM show that the exfoliation predominantly occurrs in plasticized PLA nanocomposites, whereas unexfoliated agglomerates together with exfoliated clays are observed in the nonplasticized PLA. Tensile tests indicate that the addition of 3% clay to the neat‐PLA does not affect the strength; however, it enhances the modulus of the nanocomposites in comparison to neat‐PLA. Incorporation of 3% clay to the plasticized PLA improves the modulus with respect to PLA/PEG; on the other hand, the strain at break value is lowered ～ 40%. The increase in the rate of biodegradation in composting medium is found as in the order of PLA > PLA/PEG > 3% Clay/PLA/PEG > 5% Clay/PLA/PEG > 3% Clay/PLA. DSC analysis shows that the addition of 3% clay to the neat PLA results in an increase in T_g. The addition of 20% PEG as a plasticizer to the neat‐PLA decreases T_g about 30°C, however incorporation of clays increases T_g by 4°C for the plasticized PLA. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Reinforcement of graphene nanoplatelets on plasticized poly(lactic acid) nanocomposites: Mechanical,thermal, morphology,and antibacterial properties

Plasticized poly(lactic acid) (PLA)‐based nanocomposites filled with graphene nanoplatelets (xGnP) and containing poly(ethylene glycol) (PEG) and epoxidized palm oil (EPO) with ratio 2 : 1 (2P : 1E) as hybrid plasticizer were prepared by melt blending method. The key objective is to take advantage of plasticization to increase the material ductility while preserving valuable stiffness, strength, and toughness via addition of xGnP. The tensile modulus of PLA/2P : 1E/0.1 wt % xGnP was substantially improved (30%) with strength and elasticity maintained, as compared to plasticized PLA. TGA analysis revealed that the xGnP was capable of acting as barrier to reduce thermal diffusion across the plasticized PLA matrix, and thus enhanced thermal stability of the plasticized PLA. Incorporation of xGnP also enhanced antimicrobial activity of nanocomposites toward Escherichia coli, Salmonella typhimurium, Staphylococcus aureus, and Listeria monocytogenes. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41652.     

Thermal and mechanical properties of plasticized poly(L‐lactide) nanocomposites with organo‐modified montmorillonites

Nanocomposites of poly(lactide) (PLA) and the PLA plasticized with diglycerine tetraacetate (PL‐710) and ethylene glycol oligomer containing organo‐modified montmorillonites (ODA‐M and PGS‐M) by the protonated ammonium cations of octadecylamine and poly(ethylene glycol) stearylamine were prepared by melt intercalation method. In the X‐ray diffraction analysis, the PLA/ODA‐M and plasticized PLA/ODA‐M composites showed a clear enlargement of the difference of interlayer spacing between the composite and clay itself, indicating the formation of intercalated nanocomposite. However, a little enlargement of the interlayer spacing was observed for the PLA/PGS‐M and plasticized PLA/PGS‐M composites. From morphological studies using transmission electron microscopy, a finer dispersion of clay was observed for PLA/ODA‐M composite than PLA/PGS‐M composite and all the composites using the plasticized PLA. The PLA and PLA/PL‐710 composites containing ODA‐M showed a higher tensile strength and modulus than the corresponding composites with PGS‐M. The PLA/PL‐710 (10 wt %) composite containing ODA‐M showed considerably higher elongation at break than the pristine plasticized PLA, and had a comparable tensile modulus to pure PLA. The glass transition temperature (T_g) of the composites decreased with increasing plasticizer. The addition of the clays did not cause a significant increase of T_g. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Tri‐(butanediol‐monobutyrate) citrate plasticizing poly(lactic acid): Synthesis,crystallization, thermal,and mechanical properties

Tri‐(butanediol‐monobutyrate) citrate (TBBC) as a new plasticizer for poly(lactic acid) (PLA) was synthesized via a two‐step esterification. The chemical structure of TBBC was characterized by ¹H‐nuclear magnetic resonance. The studies on solubility parameters, transparence, and storage stability indicated the good miscibility between PLA and TBBC. The glass transition, crystallization, thermal, and mechanical properties of PLA plasticized by TBBC were evaluated. With an increase in TBBC content, the glass transition temperature (T_g), melting point (T_m), and the cold crystallization temperature (T_cc) of plasticized PLA gradually shifted to a lower temperature. The elongation at break and flexibility were greatly improved by the addition of TBBC. After 30 days of storage, PLA plasticized with up to 20 wt% of TBBC exhibited good storage stability and remained the original transparence and mechanical properties. The flexibility of PLA/TBBC films can be tuned by changing TBBC content. The corresponding crystalline morphology and structure were investigated by Polarizing optical microscope and X‐ray diffraction as well. This study revealed that TBBC was miscible with PLA and may therefore be a promising plasticizer for PLA‐based packaging materials. POLYM. ENG. SCI., 55:205–213, 2015. © 2014 Society of Plastics Engineers     

Effect of mixing poly(lactic acid) with glycidyl methacrylate grafted poly(ethylene octene) on optical and mechanical properties of the blown films

Poly(lactic acid) (PLA) was plasticized with acetyl tributyl citrate (ATBC). The plasticized PLA was further blended with poly(ethylene octene) grafted with glycidyl methacrylate (POE‐g‐GMA denoted as GPOE) using a twin‐screw extruder and the extruded samples were blown using the blown thin film technique. Both ATBC and GPOE significantly influenced the physical properties of the films. Compared to neat PLA, the elongation at break and tear strength of the films were significantly improved. The cavitation and large plastic deformation observed in films subjected to the tear test were the important energy‐dissipation process, which led to a torn PLA film. Moreover, the PLA/ATBC/GPOE blown films had better transparency and water tolerance than that of neat PLA. GPOE could act as a tear resistance modifier for PLA blown films. These findings contributed new knowledge to the additives area and gave important implications for designing and manufacturing polymer packaging materials. POLYM. ENG. SCI., 55:2801–2813, 2015. © 2015 Society of Plastics Engineers     

Improvement of the flame retardancy of plasticized poly(lactic acid) by means of phosphorus‐based flame retardant fillers

The aim of this study is to improve the flame resistance and toughness of poly(lactic acid) (PLA) with the addition of low amount of flame retardant fillers and plasticizer simultaneously. Poly(ethylene glycol) (PEG) was used as plasticizer for PLA. Ammonium polyphosphate, boron phosphate, and tri‐phenyl phosphate (TPP) were used as flame retardant additives. Among these flame retardant additives, boron phosphate was synthesized from its raw materials by using microwave heating technique. Characterization of PLA/PEG‐based flame retardant composites was performed by conducting tensile, impact, differential scanning calorimeter, thermal gravimetric analysis, scanning electron microscope, limiting oxygen index, and UL‐94 vertical burning tests. Mechanical tests showed that the highest tensile strength, impact strength, and elongation at break values were obtained with the addition of ammonium polyphosphate and TPP into PLA/PEG matrix, respectively. Scanning electron microscopy analysis of the composites exhibited that the more homogeneous filler distribution in the matrix was observed for TPP containing composite. The best flame retardancy performance was also provided by TPP when compared with the other flame retardant additives in the plasticized PLA‐based composites.     

Film extrusion and film weldability of poly(lactic acid) plasticized with triacetine and tributyl citrate

Film extrusion and welding of biodegradable polymer films are important processes that must be considered in the development of compostable packaging materials. Film extrusion of poly(lactic acid) (PLA) has proved to be rather difficult because of its brittleness, but the flexibility of PLA can be improved by incorporation of a plasticizer in the material. PLA was plasticized with triacetine (TAc) and tributyl citrate (TbC). The blended materials and neat PLA were film extruded and the films were welded with constant heat (CH) welding. The films were analyzed by means of gas chromatography (GC), dynamic mechanical analysis (DMA), differential scanning calorimetry (DSC), gel permeation chromatography (GPC), contact angle measurements, and tensile testing. Storage of the plasticized films resulted in an increased crystallinity and changes in the film properties, rendering CH welding difficult. The welding process had no influence on thermal properties, such as cold crystallization temperature, melting temperature, crystallization temperature, and degree of crystallinity, of neat PLA but caused significant changes in the crystallinity of the plasticized materials. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 3239–3247, 2003     

Plasticized and nanofilled poly(lactic acid)‐based cast films: Effect of plasticizer and organoclay on processability and final properties

PLA‐based nanocomposites filled with the commercial organomodified montmorillonite Dellite 43B (D43B) and containing acetyl tri‐n‐butyl citrate (ATBC) as plasticizer were prepared by extrusion in a pilot‐scale twin‐screw extruder and melt casted into flexible films. A preliminary investigation was carried out in a laboratory batch mixer by varying blending conditions and addition procedures of the components. Indeed, the method of addition of ATBC and D43B considerably affected thermo‐mechanical properties and morphology of the resultant nanocomposites. The simultaneous introduction of both ATBC and D43B during the extrusion process allowed producing clearly exfoliated nanocomposite materials with modulated mechanical and thermal properties. Moreover, rheological results, obtained during melt extrusion, assessed the processability of nanofilled‐plasticized PLA, making this simple procedure interesting in view of the industrial production of nanostructured biomaterials based on plasticized PLA. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2013     

PLA/functionalized‐gum arabic based bionanocomposite films for high gas barrier applications

The present work focuses on the microwave synthesis of lactic acid‐grafted‐gum arabic (LA‐g‐GA) by polycondensation reaction and its influence as an additive to improve the gas barrier properties of poly(lactic acid) (PLA) films, prepared by solution casting method. It is observed that during the synthesis of LA‐g‐GA, hydrophilic gum is converted into hydrophobic due to grafting of in situ grown hydrophobic oligo‐(lactic acid). Subsequently, PLA/LA‐g‐GA bionanocomposite films are fabricated and characterized for structural, thermal, mechanical and gas barrier properties. Path breaking reduction in oxygen permeability (OP) of ～10 folds is achieved in case of PLA films containing LA‐g‐GA as filler. However, water vapor transmission rate (WVTR) is reduced up to 27% after 5 wt % addition of filler. Reduction in OP of this order of magnitude enables the PLA to compete with PET in term of enhancing shelf life and maintaining the food quality. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43458.     

Micromorphology,mechanical, crystallization and permeability properties analysis of HA/PBAT/PLA (HA,hydroxyapatite; PBAT,poly(butylene adipate‐co‐butylene terephthalate); PLA,polylactide) degradability packaging films

In this study, the self‐made nano‐hydroxyapatite (HA) and poly(butylene adipate‐co‐butylene terephthalate) copolyesters (PBAT) were used as fillers, and composite films of HA/PLA (PLA, polylactide) and HA/PBAT/PLA systems were prepared. The micromorphology, mechanical properties, thermal properties, crystallinity, water vapor permeability and oxygen permeability of the composite films were studied. The results show that the self‐made HA has a porous rod‐like structure with a size of 30–50 nm. PBAT was dispersed uniformly in the HA/PLA matrix in the form of spherical particles and formed many pores and holes. The tensile strength, elongation at break and modulus of elasticity of HA/PLA composite films were increased by adding 10 wt% PBAT. The addition of HA and PBAT played a synergistic function in improving the crystallinity of the composite films. The water vapor and oxygen permeabilities of HA/PLA and HA/10%PBAT/PLA composite films can be regulated by adjusting the amount of HA. The results of this study indicate that composite films with higher water vapor and oxygen permeabilities exhibit great potential for applications in green packaging and fresh‐keeping packaging. © 2019 Society of Chemical Industry     

Properties and weldability of plasticized polylactic acid films

The objectives of the presented work were to investigate films based on polylactic acid (PLA) and polyethylene glycol (PEG) in order to improve ductility and weldability of PLA films. The effect of plasticizer amount on the thermal, rheological, and mechanical properties of PLA plasticized films was investigated. The PEG content does affect the glass transition and the cold crystallization temperature of PLA in blends, while the melting temperature was not affected by the addition of PEG. The complex viscosity of the neat PLA granules and of plasticized films showed strong temperature and angular velocity dependence. The Young's modulus and tensile strength of plasticized films were improved with increasing plasticizer concentration, while the elongation at break stays rather constant. Plasticized PLA films were furthermore heat welded. These investigations showed that plasticized PLA films can be welded by heat welding. The obtained weld strength is strongly depending on the PEG amount as well as on selected welding parameters. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40394.     

Epoxidized soybean oil‐plasticized poly(lactic acid) films performance as impacted by storage

This study examined the effect of storage time at room temperature on the melt viscosity, thermal, and tensile properties of epoxidized soybean oil plasticized poly(lactic acid) (PLA) films manufactured through a cast extrusion process. Infrared results indicate that plasticizer migration to the surface of the film occurred after only 30 days of storage, which significantly affected the performance of plasticized films. While the melt viscosity, glass transition temperature, degree of crystallinity, tensile strength, and modulus increased, the elongation at break and energy to break decreased with storage time up to 30 days and all properties remained constant thereafter. However, the ability of stored plasticized film to cold crystallize remained unaffected since both the cold crystallization temperature and melting temperature were not affected during storage. Although plasticized film lost some flexibility after only 30 days of storage due to plasticizer migration to the surface of the film, sufficient plasticization performance still remained in plasticized PLA films for flexible packaging application even after a long storage period at ambient conditions. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43201.     

Kinetics and crystal structure of isothermal crystallization of poly(lactic acid) plasticized with triphenyl phosphate

In this article, the spherulitic growth rate of neat and plasticized poly(lactic acid) (PLA) with triphenyl phosphate (TPP) was measured and analyzed in the temperature range of 104–142°C by polarizing optical microscopy. Neat PLA had the maximum value of 0.28 μm/s at 132°C, whereas plasticized PLA had higher value than that of neat PLA, but the temperature corresponding to the maximum value was shifted toward lower one with increasing TPP content. The isothermal crystallization kinetics of neat and plasticized PLA was also analyzed by differential scanning calorimetry and described by the Avrami equation. The results showed for neat PLA and its blends with various TPP contents, the average value of Avrami exponents n were close to around 2.5 at two crystallization temperatures of 113 and 128°C, the crystallization rate constant k was decreased, and the half‐life crystallization time t_1/2 was increased with TPP content. For neat PLA and its blend with 15 wt % TPP content, the average value of n was 2.0 and 2.3, respectively, the value of k was decreased, and the value of t_1/2 was increased with crystallization temperature (T_c). Further investigation into crystallization activation energy ΔE_a of neat PLA and its blend with 15 wt % TPP showed that ΔE_a of plasticized PLA was increased compared to neat PLA. It was verified by wide‐angle X‐ray diffraction that neat PLA and its blends containing various TPP contents crystallized isothermally in the temperature range of 113–128°C all form the α‐form crystal. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Facile fabrication of highly flexible poly(lactic acid) film using alternate multilayers of poly[(butylene adipate)‐co‐terephthalate]

Poly(lactic acid) (PLA) and poly[(butylene adipate)‐co‐terephthalate] (PBAT) are both commonly used biodegradable polymers. In this study, co‐extrusion of PLA and PBAT was used to create alternately multilayered films in order to obtain high‐flexibility PLA film. The incorporation of PBAT provides enhanced flexibility to PLA and the effect is more distinct in the PLA/PBAT multilayer film as the number of layers increases. Through differential scanning calorimetric and wide‐angle X‐ray scattering analyses, the crystallinity of PLA is shown to decrease more in the multilayer film than in the blended film. Transparency is also enhanced in the multilayer film. The fabrication of alternate multilayered film by co‐extrusion of PLA and PBAT shows a new method of preparing a flexible, transparent and fully biodegradable film, which is impossible through a blending process. © 2014 Society of Chemical Industry     

Effect of plasticizer on the crystallization behavior of poly(lactic acid)

In this article, the spherulitic morphology and growth rate of the neat and plasticized poly(lactic acid) (PLA) with triphenyl phosphate (TPP) were compared and analyzed by polarizing optical microscopy with hot stage at a temperature range of 100?142°C. The spherulitic morphology of the neat PLA underwent a series of changes such as the typical Maltese Cross at less than 132°C, the disappearance of the Maltese Cross at 133°C, the irregular and distorted spherulites at higher than 134 and 142°C, respectively. For plasticized PLA, the spherulitic morphology exhibited the same changes as neat PLA, but these changes were shifted to lower temperature when compared with neat PLA. In the case of the spherulitic growth, neat PLA had the maximum value of 0.28 μm/s at 132°C, and plasticized PLA had higher values than that of neat PLA. Further analysis based on the Lauritzen–Hoffman theory was presented and results showed that the values of nucleation parameter K_g increased with TPP content. The crystallization behavior of PLA was analyzed by differential scanning calorimetry and wide‐angle X‐ray diffraction. The results showed that the degree of crystallinity of plasticized PLA markedly increased when compared with neat PLA sharply with the incorporation of plasticizer. The crystallization kinetics for the neat and plasticized PLA under isothermal crystallization at 114°C was described by the Avrami equation and the Avrami exponent is close to 2, implying that the crystallization mechanism did not change. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Thermal and mechanical properties of plasticized poly(L‐lactic acid)

Acetyl tri‐n‐butyl citrate (ATBC) and poly(ethyleneglycol)s (PEGs) with different molecular weights (from 400 to 10000) were used in this study to plasticize poly(L‐lactic acid) (PLA). The thermal and mechanical properties of the plasticized polymer are reported. Both ATBC and PEG are effective in lowering the glass transition (T_g) of PLA up to a given concentration, where the plasticizer reaches its solubility limit in the polymer (50 wt % in the case of ATBC; 15–30 wt %, depending on molecular weight, in the case of PEG). The range of applicability of PEGs as PLA plasticizers is given in terms of PEG molecular weight and concentration. The mechanical properties of plasticized PLA change with increasing plasticizer concentration. In all PLA/plasticizer systems investigated, when the blend T_g approaches room temperature, a stepwise change in the mechanical properties of the system is observed. The elongation at break drastically increases, whereas tensile strength and modulus decrease. This behavior occurs at a plasticizer concentration that depends on the T_g‐depressing efficiency of the plasticizer. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 1731–1738, 2003     

Plasticized and unplasticized PLA/organoclay nanocomposites: Short‐ and long‐term thermal properties,morphology, and nonisothermal crystallization behavior

The short‐ and long‐term thermal properties, organoclay dispersion state, and the nonisothermal crystallization kinetics of organoclay based nanocomposites of poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) plasticized PLA were investigated. Differential scanning calorimetry analyses showed that plasticization of PLA/PEG blend was diminished due to physical aging by the time. The change in thermal properties such as glass transition temperature, cold crystallization temperature, and melting temperature was monitored. It was revealed from X‐ray diffraction analyses that in long term, the exfoliated and/or intercalated organoclay structure of nanocomposites observed in short term (just after processing) was differentiated to a tactoidal form (i.e., nonseparated clays). The nonisothermal crystallization behavior and kinetics were examined by using Avrami, Ozawa, and combined Avrami–Ozawa models. Moreover, the nucleating effect of clays was investigated in terms of Gutzow and Dobrewa approaches. It was found out that clays did not act as nucleating agents in plasticized PLA nanocomposites, which was also in good agreement with activation energy values obtained from Kissinger and Takhor models. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

聚乳酸／功能化石墨烯纳米复合薄膜的制备与性能

以十八烷基胺修饰氧化石墨烯(GO–ODA)为纳米填料,通过溶液铸膜法制备了聚乳酸(PLA)／GO–ODA纳米复合薄膜。用傅立叶变换红外光谱和扫描电子显微镜对GO–ODA及纳米复合薄膜的化学结构及形貌进行了表征,并对纳米复合薄膜的拉伸性能、热稳定性和透氧率进行了测试。结果表明,GO–ODA与PLA具有良好的相容性,可均匀分散于PLA基体中,对PLA膜起到增韧增强的效果,同时GO–ODA的加入使PLA的热稳定性和氧气阻隔性均有所提高。     

Combined effect of a plasticizer and carvacrol and thymol on the mechanical,thermal, morphological properties of poly(lactic acid)

In this study, the effects of the monotherpenic phenol concentration on the properties of biocomposites containing plasticized poly(lactic acid) (PLA) with acetyl tributyl citrate (ATBC) were investigated. The monotherpenic phenols carvacrol (C) and thymol (T) were added to PLA by a melt‐blending method. The prepared samples were characterized by means of tensile testing, Fourier transform infrared spectroscopy, thermogravimetric analysis, differential scanning calorimetry, scanning electron microscopy (SEM), and antibacterial activity tests. The addition of ATBC to PLA resulted in hydrogen bonding between ATBC and PLA. We observed that ATBC, C, and T reduced the glass‐transition temperature of PLA. The presence of C and T decreased the maximum degradation temperature slightly. Because of the plasticization effect of the additives, the tensile strength and Young's modulus of PLA decreased, whereas the extent of elongation they experienced before failure increased. This effect was also observed with SEM analysis in terms of plastic deformation at break. The antibacterial activity tests showed that samples containing high concentrations of C demonstrated an improved antibacterial activity against Staphylococcus aureus, Salmonella typhimurium, and Listeria monocytogenes bacteria. We observed that C exhibited a higher inhibition against bacterial strains than T. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018 , 135, 45895.     

Fluorescent microspheres of poly(ethylene glycol)–poly(lactic acid)–fluorescein copolymers synthesized by Ugi four‐component condensation

Microparticles formed by poly(lactic acid) (PLA) and poly(ethylene glycol) (PEG) diblock copolymers containing fluorescein grafted to the polymer chain were synthesized by a Ugi four‐component condensation (UFCC) reaction. To synthesize these copolymers, lactide was first polymerized by a ring‐opening polymerization with alcohol initiators containing functional groups to give carboxyl‐ and aldehyde‐end‐functionalized PLA. Two different fluorescent block copolymers (FCPs) of PEG–PLA conjugated to fluorescein (FCP 1 and FCP 2) were then synthesized by UFCC; they gave yields in the range 65–75%. These copolymers were characterized well according their chemical structures and thermal properties, and we prepared fluorescent microspheres (FMSs) from them with the single emulsion–solvent evaporation method (FMS 1 and FMS 2). A new application of UFCC in the preparation of biomasked drug‐delivery systems is proposed. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 42994.