Polymeric ionic liquid membranes as electrolytes for lithium battery applications

A new kind of polymeric ionic liquid (PIL) membrane based on guanidinium ionic liquid (IL) with ester and alkyl groups was synthesized. On addition of guanidinium IL, lithium salt, and nano silica in the PIL, a gel PIL electrolyte was prepared. The chemical structure of the PIL and the properties of gel electrolytes were characterized. The ionic conductivity of the gel electrolyte was 5.07 × 10⁻⁶ and 1.92 × 10⁻⁴ S cm⁻¹ at 30 and 80 °C, respectively. The gel electrolyte had a low glass transition temperature (T _g ) under −60 °C and a high decomposition temperature of 310 °C. When the gel polymer electrolyte was used in the Li/LiFePO₄ cell, the cell delivered 142 mAh g⁻¹ after 40 cycles at the current rates of 0.1 C and 80 °C.     

Imidazolium‐functionalized norbornene ionic liquid block copolymer and silica composite electrolyte membranes for lithium‐ion batteries

Imidazolium‐functionalized norbornene and benzene‐functionalized norbornene were synthesized and copolymerized via ring‐opening metathesis polymerization to afford a polymeric ionic liquid (PIL) block copolymers {5‐norbornene‐2‐methyl benzoate‐block ‐5‐norbornene‐2‐carboxylate‐1‐hexyl‐3‐methyl imidazolium bis[(trifluoromethyl)sulfonyl]amide [P(NPh‐b ‐NIm‐TFSI)]} with good thermal stability. On this basis, the solid electrolyte, P(NPh‐b ‐NIm‐TFSI)–lithium bis(trifluoromethanesulfonyl)imide (LiTFSI), through blending with LiTFSI, and the nanosilica composite electrolyte, P(NPh‐b ‐NIm‐TFSI)–LiTFSI–SiO₂, through blending with LiTFSI and nanosilica, were prepared. The effects of the PILs and silica compositions on the properties, morphology, and ionic conductivity were investigated. The ionic conductivity was enhanced by an order of magnitude compared to that of polyelectrolytes with lower PIL compositions. In addition, the ionic conductivity of the nanosilica composite polyelectrolyte was obviously improved compared with that of the P(NPh‐b ‐NIm‐TFSI)–LiTFSI polyelectrolyte and increased progressively up to a maximum with increasing silica content when SiO₂ was 10 wt % or lower. The best conductivity of the P(NPh‐b ‐NIm‐TFSI)–20 wt % LiTFSI–10 wt % SiO₂ composite electrolyte with 7.7 × 10^?5 S/cm at 25 °C and 1.3 × 10^?3 S/cm at 100 °C were obtained, respectively. All of the polyelectrolytes exhibited suitable electrochemical stability windows. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134 , 44884.     

Preparation and characterization of novel hybrid thermoplastic poly(ether urethane)/poly(vinylidene fluoride) elastomers,and their application as solid polymer electrolytes

A comb‐like polyether, poly(3‐2‐[2‐(2‐methoxyethoxy)ethoxy]ethoxymethyl‐3′‐methyloxetane) (PMEOX), was reacted with hexamethylene diisocyanate and extended with butanediol in a one‐pot procedure to give novel thermoplastic elastomeric poly(ether urethane)s (TPEUs). The corresponding hybrid solid polymer electrolytes were fabricated through doping a mixture of TPEU and poly(vinylidene fluoride) with three kinds of lithium salts, LiClO₄, LiBF₄ and lithium trifluoromethanesulfonimide (LiTFSI), and were characterized using differential scanning calorimetry, thermogravimetric analysis and Fourier transform infrared spectroscopy. The ionic conductivity of the resulting polymer electrolytes was then assessed by means of AC impedance measurements, which reached 2.1 × 10^?4 S cm^?1 at 30 °C and 1.7 × 10^?3 S cm^?1 at 80 °C when LiTFSI was added at a ratio of O:Li = 20. These values can be further increased to 3.5 × 10^?4 S cm^?1 at 30 °C and 2.2 × 10^?3 S cm^?1 at 80 °C by introducing nanosized SiO₂ particles into the polymer electrolytes. Copyright © 2006 Society of Chemical Industry     

Preparation of polymer electrolytes based on the polymerized imidazolium ionic liquid and their applications in lithium batteries

The polymer electrolytes based on a polymerized ionic liquid (PIL) as polymer host and containing 1,2‐dimethyl‐3‐butylimidazolium bis(trifluoromethanesulfonyl)imide (BMMIM‐TFSI) ionic liquid, lithium TFSI salt, and nanosilica are prepared. The PIL electrolyte presents a high ionic conductivity, and it is 1.07 × 10^?3 S cm^?1 at 60°C, when the BMMIM‐TFSI content reaches 60% (the weight ratio of BMMIM‐TFSI/PIL). Furthermore, the electrolyte exhibits wide electrochemical stability window and good lithium stripping/plating performance. Preliminary battery tests show that Li/LiFePO₄ cells with the PIL electrolytes are capable to deliver above 146 mAh g^?1 at 60°C with very good capacity retention. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40928.     

Solid polymer electrolytes. XI. Preparation,characterization and ionic conductivity of new plasticized polymer electrolytes based on chemical‐covalent polyether–siloxane hybrids

A new hybrid polymer electrolyte system based on chemical‐covalent polyether and siloxane phases is designed and prepared via the sol–gel approach and epoxide crosslinking. FT‐IR, ¹³C solid‐state NMR, and thermal analysis (differential scanning calorimetry (DSC) and TGA) are used to characterize the structure of these hybrids. These hybrid films are immersed into the liquid electrolyte (1M LiClO₄/propylene carbonate) to form plasticized polymer electrolytes. The effects of hybrid composition, liquid electrolyte content, and temperature on the ionic conductivity of hybrid electrolytes are investigated and discussed. DSC traces demonstrate the presence of two second‐order transitions for all the samples and show a significant change in the thermal events with the amount of absorbed LiClO₄/PC content. TGA results indicate these hybrid networks with excellent thermal stability. The EDS‐0.5 sample with a 75 wt % liquid electrolyte exhibits the ionic conductivity of 5.3 × 10^?3 S cm^?1 at 95°C and 1.4 × 10^?3 S cm^?1 at 15°C, in which the film shows homogenous and good mechanical strength as well as good chemical stability. In the plot of ionic conductivity and composition for these hybrids containing 45 wt % liquid electrolyte, the conductivity shows a maximum value corresponding to the sample with the weight ratio of GPTMS/PEGDE of 0.1. These obtained results are correlated and used to interpret the ion conduction behavior within the hybrid networks. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 1000–1007, 2006     

The effect of ionic liquid fragment on the performance of polymer electrolytes

An ionic liquid 1‐methyl‐3‐[2‐(methacryloyloxy)ethyl]imidazolium bis(trifluoromethane sulfonylimide) (MMEIm‐TFSI) was synthesized and polymerized. Composite polymer electrolytes based on polymeric MMEIm‐TFSI (PMMEIm‐TFSI) and poly[(methyl methacrylate)‐co‐(vinyl acetate)] (P(MMA‐VAc)) were prepared, with lithium bis(trifluoromethane sulfonylimide) (LiTFSI) as target ions (Li⁺). DSC/TGA analysis showed good flexibility and thermal stability of the composite electrolyte membranes. The AC impedance showed that the ionic conductivity of the electrolytes increased with PMMEIm‐TFSI up to a maximum value of 1.78 × 10^?4 S cm^?1 when the composition was 25 wt% P(MMA‐VAc)/75 wt% PMMEIm‐TFSI/30 wt% LiTFSI at 30 °C. The composite electrolyte membrane (transmittance ≥ 90%) can also be used as the ion‐conductive layer material for electrochromic devices, and revealed excellent colorization performance. Copyright © 2011 Society of Chemical Industry     

Fabrication and properties of crosslinked poly(propylene carbonate maleate) gel polymer electrolyte for lithium‐ion battery

The poly(propylene carbonate maleate) (PPCMA) was synthesized by the terpolymerization of carbon dioxide, propylene oxide, and maleic anhydride. The PPCMA polymer can be readily crosslinked using dicumyl peroxide (DCP) as crosslinking agent and then actived by absorbing liquid electrolyte to fabricate a novel PPCMA gel polymer electrolyte for lithium‐ion battery. The thermal performance, electrolyte uptake, swelling ratio, ionic conductivity, and lithium ion transference number of the crosslinked PPCMA were then investigated. The results show that the T_g and the thermal stability increase, but the absorbing and swelling rates decrease with increasing DCP amount. The ionic conductivity of the PPCMA gel polymer electrolyte firstly increases and then decreases with increasing DCP ratio. The ionic conductivity of the PPCMA gel polymer electrolyte with 1.2 wt % of DCP reaches the maximum value of 8.43 × 10⁻³ S cm⁻¹ at room temperature and 1.42 × 10⁻² S cm⁻¹ at 50°C. The lithium ion transference number of PPCMA gel polymer electrolyte is 0.42. The charge/discharge tests of the Li/PPCMA GPE/LiNi_1/3Co_1/3Mn_1/3O₂ cell were evaluated at a current rate of 0.1C and in voltage range of 2.8–4.2 V at room temperature. The results show that the initial discharge capacity of Li/PPCMA GPE/LiNi_1/3Co_1/3Mn_1/3 O₂ cell is 115.3 mAh g⁻¹. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Ion‐conducting polymer gels of polyacrylamide embedded with K2CO3

A highly ionic conductive solid‐gel membrane based on polyacrylamide hydrogels with a K₂CO₃ additive was investigated. The polymer‐based gel was prepared by adding ionic species K₂CO₃ to a monomer solution followed by polymerization. After polymerization, the ionic species was embedded in the polymer‐based gel, where it remained. The ionic species behaved like a liquid electrolyte, whereas the polymer‐based solid‐gel membrane provided a smooth impenetrable surface that allowed for the exchange of ions. The gel membranes were obtained in the form of thin films of reasonable mechanical strength. Their ambient temperature conductivities were in the range 10^?2 to 10^?1 S/cm. The effect of K₂CO₃ concentration on the conductivity of the gels prepared was examined in the temperature range from 0 to 100°C. The microstructure and chemical composition of the gels studied were characterized by environmental scanning electron microscopy and FTIR, respectively. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 2076–2081, 2004     

Preparation and characterization of low environmental humidity sensitive ionic liquid polymer electrolytes

Methyl 3‐(3‐(2‐hydroxyethyl)imidazole‐1‐yl)propanoate chloride salt (IL‐Cl), methyl 3‐(3‐(2‐hydroxyethyl)imidazole‐1‐yl)propanoate bromate salt (IL‐Br), and their derivatives modified by polyethylene glycol (PEG) through ester‐exchange reaction (IL‐PEGs) were synthesized. First, the properties of those materials, especially their conductivity, have been extensively studied. Second, using the IL‐PEG with the highest conductivity as a plasticizer and electrolyte, a series of gel polymer electrolytes were successfully fabricated from polyurethane, poly‐1,4‐butylene adipate glycol 2000, and IL‐PEGs by melting blends with different mass ratios in a Haake torque rheometer. The surface morphology, thermal properties, and the surface resistivity of gel polymer electrolytes were studied by scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry, and surface resistivity test, respectively. Scanning electron microscopy pictures showed that the surface of polymer electrolyte is smoother than that without added IL‐PEGs. Thermogravimetric analysis results revealed that the polymer electrolytes will not decompose when the processing temperature is below 275°C. It was found that the surface resistivity of polymer electrolytes can be below 10⁹ Ω, showing a good antistatic property, and it changes slightly as the relative humidity decreases from 40% to 0.1%, indicting that the material has low humidity sensitivity. This study is a new demonstration and development in ionic liquid based polymer electrolyte. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40675.     

Gel Polymer Electrolyte with Anion‐Trapping Boron Moieties via One‐Step Synthesis for Symmetrical Supercapacitors

A novel gel polymer electrolyte (GPE) which is based on new synthesized boron‐containing monomer, benzyl methacrylate, 1 m LiClO₄/N,N‐dimethylformamidel liquid electrolyte solution is prepared through a one‐step synthesis method. The boron‐containing GPE (B‐GPE) not only displays excellent mechanical behavior, favorable thermal stability, but also exhibits an outstanding ionic conductivity of 2.33 mS cm^?1 at room temperature owing to the presence of anion‐trapping boron sites. The lithium ion transference in this gel polymer film at ambient temperature is 0.60. Furthermore, the symmetrical supercapacitor which is fabricated with B‐GPE as electrolyte and reduced graphene oxide as electrode demonstrates a broad potential window of 2.3 V. The specific capacitance of symmetrical B‐GPE supercapacitors retains 90% after 3000 charge–discharge cycles at current density of 1 A g^?1.     

Composite polymer electrolytes based on the low crosslinked copolymer of linear and hyperbranched polyurethanes

Low crosslinked copolymer of linear and hyperbranched polyurethane (CHPU) was prepared, and the ionic conductivities and thermal properties of the composite polymer electrolytes composed of CHPU and LiClO₄ were investigated. The FTIR and Raman spectra analysis indicated that the polyurethane copolymer could dissolve more lithium salt than the corresponding polymer electrolytes of the non crosslinked hyperbranched polyurethane, and showed higher conductivities. At salt concentration EO/Li = 4, the electrolyte CHPU30‐LiClO₄ reached its maximum conductivity, 1.51 × 10^?5 S cm^?1 at 25°C. DSC measurement was also used for the analysis of the thermal properties of polymer electrolytes. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 3607–3613, 2007     

1H NMR,thermal, and conductivity studies on PVAc based gel polymer electrolytes

The lithium‐ion conducting gel polymer electrolytes (GPE), PVAc‐DMF‐LiClO₄ of various compositions have been prepared by solution casting technique. ¹H NMR results reveal the existence of DMF in the gel polymer electrolytes at ambient temperature. Structure and surface morphology characterization have been studied by X‐ray diffraction analysis (XRD) and scanning electron microscopy (SEM) measurements. Thermal and conductivity behavior of polymer‐ and plasticizer‐salt complexes have been studied by differential scanning calorimetry (DSC), TG/DTA, and impedance spectroscopy results. XRD and SEM analyses indicate the amorphous nature of the gel polymer‐salt complex. DSC measurements show a decrease in T_g with the increase in DMF concentrations. The thermal stability of the PVAc : DMF : LiClO₄ gel polymer electrolytes has been found to be in the range of (30–60°C). The dc conductivity of gel polymer electrolytes, obtained from impedance spectra, has been found to vary between 7.6 × 10^?7 and 4.1 × 10^?4 S cm^?1 at 303 K depending on the concentration of DMF (10–20 wt %) in the polymer electrolytes. The temperature dependence of conductivity of the polymer electrolyte complexes appears to obey the VTF behavior. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Effective influences of 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide (EMIMTFSI) ionic liquid on the ion transport properties of micro-porous zinc-ion conducting poly (vinyl chloride) /poly (ethyl methacrylate) blend-based polymer electrolytes

A series of new gel polymer electrolytes (GPEs) based on different concentrations of a hydrophobic ionic liquid (IL) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide (EMIMTFSI) entrapped in an optimized typical composition of polymer blend-salt matrix [poly(vinyl chloride) (PVC) (30 wt%) / poly(ethyl methacrylate) (PEMA) (70 wt%) : 30 wt% zinc triflate Zn(CF₃SO₃)₂] has been prepared using facile solution casting technique. The AC impedance analysis has revealed the occurrence of the maximum ionic conductivity of 1.10 × 10^?4 Scm^?1 at room temperature (301 K) exhibited by the PVC/PEMA- Zn(OTf)₂ system containing 80 wt% ionic liquid. The addition of EMIMTFSI into the optimized PVC/PEMA- Zn(OTf)₂ system in different weight percentages enhances the number of free zinc ions thereby leading to enrichment of ionic conductivity. The structural and complexation behaviour of the as prepared polymer gel electrolytes was substantiated by subjecting these electrolyte films to X-ray diffraction (XRD) and Attenuated total reflectance - Fourier transformed infrared (ATR-FTIR) investigations. The wider electrochemical stability window ~ 3.23 V and a reasonable cationic transference number (t_Zn ²⁺) of 0.63 have been attained for the polymer gel electrolyte film containing higher loading of (80 wt%) ionic liquid. The development of the amorphous phase of these gel polymer electrolyte membranes with increasing ionic liquid content was observed from scanning electron microscopic (SEM) analysis. The results of the current work divulge the assurance of developing GPEs based on ionic liquids for prospective application in zinc battery systems.     

Solid polymer electrolytes. VII. Preparation and ionic conductivity of gelled polymer electrolytes based on poly(ethylene glycol) diglycidyl ether cured with α,ω‐diamino poly(propylene oxide)

Crosslinked polymer electrolyte networks were prepared from poly(ethylene glycol) diglycidyl ether blended with an epoxy resin (diglycidyl ether of bisphenol A) in different ratios and then cured with α,ω‐diamino poly(propylene oxide) in the presence of lithium perchlorate (LiClO₄) as a lithium salt. The ionic conductivities of these polymer electrolytes were determined by alternating current (AC) impedance spectroscopy. Propylene carbonate (PC) was used as a plasticizer to form gelled polymer electrolyte networks. The conductivities of the polymer electrolytes containing 46 wt % PC plasticizer were approximately 5 × 10^?4 S cm^?1 at 25°C and approximately 10^?3 S cm^?1 at 85°C. These polymer electrolytes were homogeneous and exhibited good mechanical properties. The effects of the polymer composition, plasticizer content, salt concentration, and temperature on the ionic conductivities of the polymer electrolytes were examined. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 92: 1264–1270, 2004     

Composite polymer electrolytes based on electrospun thermoplastic polyurethane membrane and polyethylene oxide for all‐solid‐state lithium batteries

To improve the electrochemical properties and enhance the mechanical strength of solid polymer electrolytes, series of composite polymer electrolytes (CPEs) were fabricated with hybrids of thermoplastic polyurethane (TPU) electrospun membrane, polyethylene oxide (PEO), SiO₂ nanoparticles and lithium bis(trifluoromethane)sulfonamide (LiTFSI). The structure and properties of the CPEs were confirmed by SEM, XRD, DSC, TGA, electrochemical impedance spectroscopy and linear sweep voltammetry. The TPU electrospun membrane as the skeleton can improve the mechanical properties of the CPEs. In addition, SiO₂ particles can suppress the crystallization of PEO. The results show that the TPU‐electrospun‐membrane‐supported PEO electrolyte with 5 wt% SiO₂ and 20 wt% LiTFSI (TPU/PEO‐5%SiO₂‐20%Li) presents an ionic conductivity of 6.1 × 10^?4 S cm^?1 at 60 °C with a high tensile strength of 25.6 MPa. The battery using TPU/PEO‐5%SiO₂‐20%Li as solid electrolyte and LiFePO₄ as cathode shows an attractive discharge capacity of 152, 150, 121, 75, 55 and 26 mA h g^?1 at C‐rates of 0.2C, 0.5C, 1C, 2C, 3C and 5C, respectively. The discharge capacity of the cell remains 110 mA h g^?1 after 100 cycles at 1C at 60 °C (with a capacity retention of 91%). All the results indicate that this CPE can be applied to all‐solid‐state rechargeable lithium batteries. © 2018 Society of Chemical Industry     

Synthesis and characterization of novel crosslinked polyurethane–acrylate electrolyte

Flexible, transparent, and crosslinked polymer films were synthesized by polymerization of PEG‐modified urethane acrylate using a simple method. A series of novel solid polymer electrolytes and gel electrolytes were prepared based on this type of polymer film. To understand the interactions among salt, solvent, and polymer, the swelling behaviors of the crosslinked polymer in pure propylene carbonate (PC) and liquid electrolyte solutions (LiClO₄/PC) were investigated. The results showed that the swelling rate in the electrolyte solution containing moderate LiClO₄ was greater than that in pure PC. Thermogravimetric analysis (TGA) also supported the interaction between the solvent and polymer. The morphology and crystallinity of the crosslinked polymer and polymer electrolytes were studied using atomic force microscopy (AFM) and wide‐angle X‐ray diffraction (WAXD) spectroscopy. The effects of the content of the electrolyte solution on the ionic conductivity of gel electrolytes were explored. The dependence of the conductivity on the amount of the electrolyte solution was nonlinear. With a different content of the plasticizer, the ionic conduction pathway of the polymer electrolytes would be changed. The best ionic conductivity of the gel electrolytes, which should have good mechanical properties, was 4 × 10^r?3 S cm^?1 at 25°C. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 340–348, 2003     

In situ thermal polymerization of an ionic liquid monomer for quasi‐solid‐state dye‐sensitized solar cells

In situ thermal polymerization of a model ionic liquid monomer and ionic liquids mixture to form gel electrolytes is developed for quasi‐solid‐state dye‐sensitized solar cells (Q‐DSSCs). The chemical structures and thermal property of the monomers and polymer are investigated in detail. The effect of iodine concentration on the conductivity and triiodide diffusion of the gel electrolytes is also investigated in detail. The conductivity and triiodide diffusion of the gel electrolytes increase with the increasing I₂ concentration, while excessive I₂ contents will decrease the electrical performances. Based on the in situ thermal polymeric gel electrolytes for Q‐DSSCs, highest power conversion efficiency of 5.01% has been obtained. The superior long‐term stability of fabricated DSSCs indicates that the cells based on in situ thermal polymeric gel electrolytes can overcome the drawbacks of the volatile liquid electrolyte. These results offer us a feasible method to explore new gel electrolytes for high‐performance Q‐DSSCs. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42802.     

Physical gels of [BMIM][BF4] by N‐ tert‐butylacrylamide/ethylene oxide based triblock copolymer self‐assembly: Synthesis,thermomechanical, and conducting properties

We report a strategy to prepare and characterize mechanically robust, transparent, thermoreversible physical gels of an ionic liquid 1‐butyl‐3‐methylimidazolium tetrafluoroborate, [BMIM][BF₄], to harness its good ionic conductivity and electrolytic properties for solid‐state electrolyte and lithium ion battery applications. Physical gels are prepared using a triblock copolymer comprising central polyethylene oxide block that is soluble in [BMIM][BF₄] and the end blocks, poly(N‐tert‐butylacrylamide), that are insoluble in [BMIM][BF₄]. Transparent, strong, physical ion‐gels with significant mechanical strength can be formed at low concentration of the triblock copolymer (～5 wt %), unlike previous reports in which chemical gels of [BMIM][BF₄] are obtained at very high polymer concentration. Our gels are thermoreversible and thermally stable, showing 1–4% weight loss up to 200°C in air. Gelation behavior, mechanical properties, and ionic conductivity of these ion‐gels can be easily tuned by varying the concentration or N‐tert‐butylacrylamide block length in the triblock copolymer. These new non‐volatile, reprocessable, mechanically robust, [BMIM][BF₄]‐based physical ion‐gels obtained from a simple and convenient preparation method are promising materials for solid‐state electrolyte applications. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Compatibility of quaternary ammonium-based ionic liquid electrolytes with electrodes in lithium ion batteries

Electrochemical intercalation/deintercalation behavior of lithium into/from electrodes of lithium ion batteries was comparatively investigated in 1 mol/L LiClO₄ ethylene carbonate-diethyl carbonate (EC-DEC) electrolyte and a quaternary ammonium-based ionic liquid electrolyte. The natural graphite anode exhibited satisfactory electrochemical performance in the ionic liquid electrolyte containing 20 vol.% chloroethylenene carbonate (Cl-EC). This is attributed to the mild reduction of solvated Cl-EC molecules at the graphite/ionic electrolyte interface resulting in the formation of a thin and homogenous SEI on the graphite surface. However, rate capability of the graphite anode is poor due to the higher interfacial resistance than that obtained in 1 mol/L LiClO₄/EC-DEC organic electrolyte. Spinel LiMn₂O₄ cathode was also electrochemically cycled in the ionic electrolyte showing satisfactory capacity and reversibility. The ionic electrolyte system is thus promising for 4 V lithium ion batteries based on the concept of “greenness and safety”.     

Enhancement of density and ionic conductivity for garnet-type Li5La3Ta2O12 solid electrolyte by self-consolidation strategy

Garnet-type Li₅La₃Ta₂O₁₂ (LLTaO) solid electrolyte is a potential candidate component for future all-solid-state batteries due to its extraordinary stability against the reaction with molten lithium. In contrast with traditional cold isostatic pressing (CIP) method, which generally pursues ultra-high pressure, this paper tries to enhance the density and ionic conductivity of LLTaO by self-consolidation strategy without the assistance of any pressing operations. A LLTaO bulk with a relative density of 95% is obtained. SEM images reveal that the bulk sample is assembled by large dense particles in size of tens of microns indicating that the interstitial space among the particles has been dramatically minimized. Accordingly, the total ionic conductivity and the bulk ionic conductivity at 30?°C are promoted up about one order of magnitude higher to 2.63?× 10^?5 S?cm^?1 and 1.41?×?10^?4 S?cm^?1, respectively. Moreover, the lithium ionic migration network in the crystalline unit cell of LLTaO is first explored from its assembled way. A hexagon-like basic unit with tetrahedral Li1 joint sites and Li1- - Li1 edges is identified. The tetrahedral Li1 sites act as crucial junctions for the transportation of lithium ions. This work would significantly stimulate the development of LLTaO electrolyte membrane technology.