Current-ramp assisted sintering of 3YSZ: Electrochemical and microstructural comparison to flash and thermal sintering

Flash sintering features an unoptimized and uncontrolled rise in current density and sample conductivity. By using a controlled current-ramp technique with a predetermined ramp function, microstructure and electrochemical properties can be improved. This current-ramp method is investigated through use of test functions that follow square-root, linear, and parabolic time dependence with comparison to conventional flash sintering and thermal sintering. Steeper ramp functions during the sintering result in higher activation energy, suggesting a change in the vacancy concentration for both the bulk and grain boundary regions. Estimation of the grain boundary domain width suggests a grain size dependence of the unique space charge contribution to conduction independent of sintering method. Contrary to conventional wisdom, flash sintering can actually result in enhanced grain growth compared to controlled current-ramps and conventional sintering, implying that uncontrolled rise in current to a set cutoff may not be the optimal method for densification.     

Flash sintering of yttria-stabilized zirconia powders coated with nanoscale films of alumina by atomic layer deposition

The addition of small quantities of aluminum oxide (Al₂O₃) to 8 mol% yttria-stabilized zirconia (8YSZ) benefits conventional sintering by acting as a sintering aid and altering grain growth behavior. However, it is uncertain if these benefits observed during conventional sintering extend to flash sintering. In this work, nanoscale films of Al₂O₃ are deposited on 8YSZ powders by particle atomic layer deposition (ALD). The ALD-coated powders were flash sintered using voltage-to-current control and current rate experiments. The sintering behavior, microstructural evolution, and ionic conductivities were characterized. The addition of Al₂O₃ films changed the conductivity of the starting powder, effectively moving the flash onset temperature. The grain size of the samples flashed with current rate experiments was ~65% smaller than that of conventionally sintered samples. Measurement of grain size and estimates of sample density as a function of temperature during flash sintering showed that small quantities of Al₂O₃ can enhance grain growth and sintering of 8YSZ. This suggests that Al₂O₃ dissolves into the 8YSZ grain boundaries during flash sintering to form complexions that enhance the diffusion of species controlling these processes.     

In situ measurement of temperature and reduction of rutile titania using energy dispersive x-ray diffraction

Using in situ energy dispersive x-ray diffraction (EDXRD) the average specimen temperature of TiO₂ in the steady state of flash is experimentally determined. Comparison of the microstructure for flash sintering and conventional sintering in addition to the temperature determined from calibration of the unit cell expansion indicates that rapid Joule heating during flash sintering causes densification and grain growth comparable with conventional sintering. An average temperature approximation model is proposed to account for greybody radiation and thermal conduction. The inhomogeneity of the grain growth across the sample length is confirmed to correlate with inhomogeneity in temperature distribution and this suggests a current induced Peltier effect in n-type TiO₂.     

Sintering kinetics and properties of NiFe2O4-based ceramics inert anodes doped with TiN nanoparticles

Sintering kinetics of NiFe₂O₄-based ceramics inert anodes for aluminum electrolysis doped 7 wt% TiN nanoparticles were conducted to investigate densification and grain growth behaviors. The linear shrinkage increased gradually with the increasing sintering temperature between 1000 and 1450°C, whereas the linear shrinkage rate exhibited a broad peak. The maximum linear shrinkage rate was obtained at 1189.4°C, and the highest densification rate was achieved at the relative density of 75.20%. Based on the pressureless sintering kinetics window, the sintering process was divided into the initial stage, the intermediate stage, and the final stage. The grain growth exponent reduced with increased sintering temperature, whereas the grain growth activation energy decreased by increasing sintering temperature and shortening dwelling time. The grain growth was mainly controlled by atomic diffusion. NiFe₂O₄-based ceramics possessed high-temperature semiconductor essential characteristics. The electrical conductivity of NiFe₂O₄-based ceramics first increased and then decreased with increasing sintering temperature, reached their maximum value (960°C) of 33.45 S/cm under 1300°C, mainly attributed to the relatively dense and uniform microstructure. The thermal shock resistance of NiFe₂O₄-based ceramic was improved by a stronger grain boundary bonding strength and lower coefficient of linear thermal expansion.     

Influence of grain size on the thermal conductivity of tin oxide ceramics

Measurement of the thermal diffusivity by the laser flash technique has been used to evaluate thermal conductivity values between 20°C and 900°C for tin oxide ceramics. By using MnO₂ as a sintering additive, strong variation of the microstructure in terms of porosity and average grain size was achieved in the samples. For dense ceramics, larger average grain size yielded a significant increase in the room temperature thermal conductivity. This could be attributed to a reduction of the number of grain boundaries in the heat flow path. The grain boundary interfacial resistance was consequently estimated at 4.1×10⁻⁸ m² KW⁻¹. Data concerning the effects of additive amount, pore content, and temperature are also reported.     

Impedance Spectroscopy and Dielectric Properties of Flash Versus Conventionally Sintered Yttria‐Doped Zirconia Electroceramics Viewed at the Microstructural Level

The defect chemistry‐modulated dielectric properties of dense yttria‐doped zirconia ceramics prepared by conventional sintering (at 1350°C–1500°C) and electric field‐assisted flash sintering (55 V/cm at 900°C) were studied by impedance spectroscopy. While the bulk dielectric properties from both sets of samples showed only small and insignificant changes in conductivity and permittivity, respectively, a huge increase of these properties was measured for the grain boundaries in the flash sintered specimens. A close analysis of these results suggests that flash sintering reduced grain‐boundary thickness (by about 30%), while increasing the concentration of oxygen vacancies near these interfaces (by about 49%). The underlying mechanism proposed is electric field‐assisted generation and accommodation of defects in the space‐charge layers adjacent to the grain surface. The changes in measured permittivity are attributed to the boundary thickness effect on capacitance, while conductivity involved variations in its defect density‐dependent intrinsic value, accounting for changes also observed in grain‐boundary relaxation frequencies. Therefore, in terms of modifications to the specific dielectric properties of these materials, the overall consequence of flash sintering was to considerably lower the semi‐blocking character of the grain boundaries.     

Grain growth kinetics of 3 mol. % yttria-stabilized zirconia during flash sintering

Grain growth kinetics of dense 3 mol. % yttria-stabilized zirconia (3YSZ) ceramics during both DC flash sintering and conventional annealing were investigated using the grain size as a marker of microstructure evolution. The results indicated faster grain growth under greater current density. In contrast to conventionally annealed specimen, the grain boundary mobility was enhanced by almost two orders of magnitude with the applied electric current, revealing that joule heating alone was not sufficient to account for the experimental results. Instead, activation energy for grain growth decreased significantly due to electro-sintering. Systematic characterization of graded microstructure further indicated that local oxygen vacancies and specimen temperature were responsible for a grain size transition. Based on electrochemical reaction involved in flash sintering, grain size reduction at the cathode was proposed to be attributed to the local rearrangement of lattice cations and generated oxygen ions.     

Reactive flash sintering of high-entropy oxide (La0.2Nd0.2Sm0.2Eu0.2Gd0.2)2Zr2O7: Microstructural evolution and aqueous durability

Herein, the phase evolution, densification and grain growth process of the high entropy ceramics during flash sintering were systematically characterized and quantified to understand the microstructural evolution for the first time. It was demonstrated that the densification rate of (La_0.2Nd_0.2Sm_0.2Eu_0.2Gd_0.2)₂Zr₂O₇ by flash sintering in this work was generally around 60 times that of conventional sintering at 1600 °C, while the grain growth rate by flash sintering was only around 1.5–6 times that of conventional sintering, indicating that grain growth was suppressed during flash sintering. The grain growth mechanisms by flash sintering and conventional sintering could be both attributed to surface diffusion and volume diffusion. In addition, the flash sintered high-entropy ceramics as promising immobilization materials for high-level radioactive waste (HLW) exhibited excellent aqueous durability with normalized leaching rates of Nd, Gd and Zr approximately 10^?6～10^?7 g m^?2 d^?1 after 42 days, which were much lower than most reported pyrochlore materials.     

Thermal Conductivity Characterization of Hafnium Diboride-Based Ultra-High-Temperature Ceramics

We evaluated the thermal conductivity of HfB₂-based ultra-high-temperature ceramics from laser flash diffusivity measurements in the 25°–600°C temperature range. Commercially available powders were used to prepare HfB₂ composites containing 20 vol% SiC, some including TaSi₂ (5 vol%) and Ir (0.5 or 2 vol%) additions. Samples were consolidated via conventional hot pressing or spark plasma sintering. Processing differences were shown to lead to differences in magnitude and temperature dependence of effective thermal conductivity. We compared results with measured values from heritage materials and analyzed trends using a network model of effective thermal conductivity, incorporating the effects of porosity, grain size, Kapitza resistance, and individual constituent thermal conductivities.     

Improvement in fracture strength in electrically conductive AlN ceramics with high thermal conductivity

It is possible to impart electrical conductivity to insulating aluminum nitride (AlN) ceramics by precipitating a yttrium oxycarbide grain boundary phase with electrical conductivity. However, previously, sintering at high temperature was required to increase the electrical conductivity through the transformation of the grain boundary phase from yttrium aluminum oxide (Al₂Y₄O₉) to rare-earth oxycarbide. As a result, the increase in electrical conductivity was accompanied with a considerable decrease in the fracture strength due to grain growth of AlN. In this study, sintering temperature and additive compositions were investigated to maintain the high strength of electrically conductive AlN without losing the high thermal conductivity.     

Effect of thermal insulation on microstructural homogeneity and onset temperature of flash sintered materials

The present work aimed to reduce the microstructure heterogeneity inherent to flash sintering by using alumina blankets as a thermal insulator around ZnO cylindrical samples during the sintering process, under different electric field conditions. Thermal insulation significantly reduced the flash onset temperature and the grain size heterogeneity. For higher electric fields, a temperature reduction as high as 480 °C was observed, which also led to lower densification. These findings were discussed in terms of changes in the heat loss dynamics coupled with the adsorbed water retention, both promoted by the applied thermal insulation. A model to estimate the temperature at stage III of flash sintering was proposed. The final temperature reached with thermal insulation did not differ significantly from the ones without it. Thus, thermal insulation could represent an alternative route to flash sinter materials with lower furnace temperatures with energy savings up to 78 % and a more homogeneous microstructure.     

Development of a processing map for safe flash sintering of gadolinium-doped ceria

Flash sintering was discovered in 2010, where a dog-bone-shaped zirconia sample was sintered at a furnace temperature of 850°C in <5 s by applying electric fields of ~100 V cm⁻¹ directly to the specimen. Since its discovery, it has been successfully applied to several if not all oxides and even ceramics of complex compositions. Among several processing parameters in flash sintering, the electrical parameters, i.e., electric field and electric current, were found to influence the onset temperature for flash and the degree of densification respectively. In this work, we have systematically investigated the influence of the electrical parameters on the onset temperature, densification behavior, and microstructure of the flash sintered samples. In particular, we focus on the development of a processing map that delineates the safe and fail regions for flash sintering over a wide range of applied current densities and electric fields. As a proof of concept, gadolinium-doped ceria (GDC) is shown as an example for developing of such a processing map for flash sintering, which can also be transferred to different materials systems. Localization of current coupled with hot spot formation and crack formation is identified as two distinct failure modes in flash sintering. The grain size distribution across the current localized and nominal regions of the specimen was analyzed. The specimens show exaggerated grain growth near the positive electrode (anode). The region adjacent to the negative electrodes (cathode) showed retarded densification with large concentration of isolated pores. The electrical conductivity of the flash sintered and conventional sintered samples shows identical electrical conductivity. This quantitative analysis indicates that similar sintering quality of the GDC can be achieved by flash sintering at temperature as low as 680°C.     

Effect of hot-pressing sintering on thermal and electrical properties of AlN ceramics with impedance spectroscopy and dielectric relaxations analysis

The effects of hot-pressing sintering on the phase composition, microstructure, thermal and electrical properties of AlN ceramics with CeO₂–CeF₃ additives were studied. During hot-pressing sintering, high pressure reduced the grain boundary phase CeAlO₃ and decreased the concentration of oxygen in AlN ceramics. The hot-pressing sintered AlN samples had a much higher thermal conductivity of 191.9 W/m·K than pressureless sintered ones because of the great reduction of grain boundary phases and oxygen impurities in AlN ceramic. As the carbon content in hot-pressing sintered sample was very high, carbon contamination led to the decrease in electrical resistivity and changes in polarization mechanisms for AlN ceramics. The relaxation peak in the dielectric temperature spectrum with an activation energy of 0.64 eV for hot-pressing sintered samples was caused by electrons from free carbon at low temperature. Overall, hot-pressing sintering can effectively increase the thermal conductivity and change the electrical properties of AlN ceramics.     

The microstructural origin of rapid densification in 3YSZ during ultra-fast firing with or without an electric field

Recent research has shown that very rapid heating of 3YSZ powder compacts (ultra-fast firing), whether by passing an electric current through the sample (flash sintering) or by using external heat sources, causes a great acceleration of densification rate for a given relative density and temperature. Here, the microstructural evolution of 3YSZ is studied using four sintering methods with widely differing heating rates, produced with or without electric fields. The microstructural development depended greatly on thermal history. Most significantly, slow, conventional heating resulted in pores much larger than the grain size, whereas most pores were smaller than the grain size with the rapid heating methods, whether the heating involved an electric field or not. The smaller pore size clearly provides a major contribution to the acceleration of densification following rapid heating. In contrast, grain growth was not suppressed by rapid heating but was suppressed by an electric field.     

Thermal conductivity of spark plasma sintered SiC ceramics with Alumina and Yttria

In this study, dense SiC ceramics were fabricated at 1650?1750 °C for 10?60 min by spark plasma sintering (SPS) using 3?10 wt.% Al₂O₃-Y₂O₃ as sintering additives. Effects of sintering temperature, sintering additive content and holding time on microstructure as well as correlations between microstructure and thermal conductivity were investigated. An increase in the sintering temperature promotes grain growth. Extending holding time has little influence on grain size but results in formation of continuous network of sintering additive, which increases interfacial thermal resistance and thus decreases thermal conductivity. For SiC ceramics composed of continuous SiC matrix and discrete secondary phase (yttrium aluminum garnet, YAG), an increase in the sintering additive content results in smaller grain size and lower thermal conductivity. The lower thermal conductivity of the SiC ceramic with higher sintering additive content is mainly due to the smaller grain size rather than the low intrinsic thermal conductivity of YAG.     

DC electric field-assisted hot pressing of zirconia: Methodology,phenomenology, and sintering mechanism

Flash sintering (FS) is an important technique in the field of ceramic sintering. Nevertheless, conventional FS is less attractive for practical applications because of the complex shapes and small sizes of the specimens. In this study, using the novel electric field-assisted hot pressing (FAHP) technique, we successfully achieved FS during the net-shape hot pressing (HP) process for the first time. It was found that the 3 mol% yttria-stabilized zirconia (3YSZ) can be flash sintered at 909°C using a fairly low DC field of 33 V/cm under 30 MPa pressure. The grain sizes of the FAHP-sintered samples were 20% smaller than that of the HP-sintered sample. When the current density limit is ≥240 mA/mm², 3YSZ can be fully densified during the flash events. Careful analysis of the sintering curves suggests that although the carrier type or concentration is changed during flash events, it cannot explain the ultrafast densification. Additionally, we devised a qualitative method to analyze the densification mechanism. The results indicated that the ultrafast densification observed during flash events resulted from the synergistic effects of the rapid heating rate and peak sample temperature. Finally, the atomic force microscopy confirmed the lower grain boundary energy for the FAHP-sintered samples, which accounts for the smaller grain sizes than the HP-sintered sample. We believe that the FAHP technique could create new possibilities for theoretical and applied research on field-assisted sintering techniques.     

Thermal conductivity of pressed powder compacts: tin oxide and alumina

Three aspects, which significantly reduce heat transfer through a polycrystalline material, are considered in this paper: porosity, grain boundary thermal resistance and the state of the grain–grain contacts. Tin oxide and alumina were chosen as model systems. Tin oxide, without a sintering additive, does not densify during thermal treatment but grain growth is not inhibited and consequently the microstructure can be varied. In alumina, variation of the thermal treatment conditions varies both grain size and porosity. Thermal conductivity measurements, using the laser-flash technique, reveal that the thermal resistance of a pressed powder compact is almost independent of temperature and at least a factor of 2.5 greater than a consolidated material with similar pore volume fraction and grain size. The reduced contact area of the grain–grain interfaces in the green body can explain this as demonstrated by numerical simulation. We also show that larger grain size increases the thermal conductivity of the porous ceramic.     

Two-Step Sintering of Ceramics with Constant Grain-Size, I. Y2O3

Isothermal and constant-grain-size sintering have been carried out to full density in Y₂O₃ with and without dopants, at as low as 40% of the homologous temperature. The normalized densification rate follows Herring's scaling law with a universal geometric factor that depends only on density. The frozen grain structure, however, prevents pore relocation commonly assumed in the conventional sintering models, which fail to describe our data. Suppression of grain growth but not densification is consistent with a grain boundary network pinned by triple-point junctions, which have a higher activation energy for migration than grain boundaries. Long transients in sintering and grain growth have provided further evidence of relaxation and threshold processes at the grain boundary/triple point.     

Electrode Effects on Microstructure Formation During FLASH Sintering of Yttrium‐Stabilized Zirconia

Systematic microstructural statistics for 3 mol% yttria‐stabilized zirconia synthesized by both conventional sintering and flash sintering with AC and DC current were obtained. Within the gage section, flash sintered microstructures were indistinguishable from those synthesized by conventional sintering procedures. With both techniques, full densification was obtained. However, from both AC and DC flash sintered specimens, heterogeneous grain size distributions and residual porosity were observed in the proximity of the electrodes. After DC sintering, an almost 400 times increased average grain size was observed near cathode compared to the gage section, unlike areas close to the anode. Concepts of Joule heating alone were not sufficient to explain the experimental observations. Instead, the activation energy for grain growth close to the cathode is lowered considerably during flash sintering, hence suggesting that electrode effects can cause significant heterogeneities in microstructure evolution during flash sintering. Microstructural characterization further indicated that microfracturing during green‐pressing and variations in contact resistance between the electrodes and the ceramic may also contribute to grain size gradients and hence local variations of physical properties.     

Design of Electroceramics for Solid Oxides Fuel Cell Applications: Playing with Ceria

Nanostructured samaria- and gadolinia-doped ceria (SDC and GDC) powders were synthesized at low temperature (400°C) using diamine-assisted direct coprecipitation method. Fast-firing (f.f.) processes, where sintering temperatures are reached in a short time to promote lattice diffusion, were compared with conventional sintering, for the formation of dense microstructures from the nanostructured powders. Highly dense SDC and GDC samples (96%) with reduced grain size (150 nm) were obtained by f.f. even at 1300°–1400°C and, unexpectedly, high electrical conductivity and low blocking effect at grain boundary was obtained. Conventionally sintered samples showed that the grain boundary resistivity decreased with increasing the grain size, in agreement with the increase in geometrical bulk volume/grain boundary area ratio. Conversely, f.f. samples showed grain boundary resistivity smaller for small grain size. The above effect was observed only for high dopant (>10% molar) contents. The combined effect of powder grain size, dopant content, and sintering temperature–time profile, can be exploited to tune ceria microstructures for specific ionic device applications.