Application of Response Surface Methodology for Optimization of Bromelain Extraction in Aqueous Two-Phase System

Extraction of bromelain from pineapple fruit in an aqueous two phase system (ATPS) composed of polyethylene glycol (PEG) 1500 and potassium phosphate has been studied using response surface methodology. The various process variables such as PEG, potassium phosphate and NaCl concentration, and pH were optimized using a central composite rotatable design (CCRD) of response surface methodology (RSM) based on the partition coefficient, % yield, and purification factor of an enzyme. An optimized ATPS composed of 14% (w/w) PEG 1500, 17.66% (w/w) potassium phosphate and 1 mM sodium chloride at pH 7.5 was used to purify bromelain from a pineapple fruit. With this system, a maximum enzyme partition coefficient of 12.62 and %yield of 90.33 in the top PEG-rich phase with a purification factor of 2.4 was predicted. The enzyme partition coefficient, % yield, and purification factor obtained from experimentation are 12.22, 89.65, and 2.8, respectively, in the top PEG phase. The response model is validated by the closeness between the predicted and experimental results.     

Reverse micellar extraction of bromelain from Ananas comosus L. Merryl

BACKGROUND: A reverse micellar system (RMS) of ionic surfactants is used for the first time for the extraction and primary purification of fruit bromelain (EC 3.4.22.33) from the aqueous extract of pineapple (Ananas comosus L. Merryl). The effect of various process parameters on both forward and back extraction of bromelain is studied to improve the extraction efficiency of RMS. Most of the reverse micellar extraction (RME) studies reported so far are on model systems and its application to enzyme extraction from a natural source is rarely reported. RESULTS: Studies carried out with ionic surfactants sodium bis(2‐ethylhexyl)sulfosuccinate (AOT) and cetyltrimethylammonium bromide (CTAB) confirmed that electrostatic interaction was the main driving force for the extraction of fruit bromelain. Among the two surfactants studied, CTAB was found to be the most suitable for the extraction of fruit bromelain with respect to activity recovery (97.56%) and degree of purification (4.54 fold) when employed as a 150 mmol L^?1 CTAB/iso‐octane/5% (v/v) hexanol/15% (v/v) butanol system. Activity recovery with a counterionic system is higher (94.30%) in comparison with isopropyl alcohol added system (85.35%). CONCLUSION: RME could be used as an efficient primary purification step for the recovery of bromelain from pineapple juice. Reverse micellar phase components can easily be recovered and efficiently reused for fresh or subsequent extraction, which contributes favorably to the process economics and environmental issues. Copyright © 2007 Society of Chemical Industry     

A simple method for purification of bromelain in a thermosensitive triblock copolymer-based protection system and recycling of phase components

In the work, we chose stem bromelain as a model to investigate the storage and purification of bromelain from pineapple peel. Extraction of bromelain from pineapple peel using a two-stage aqueous two-phase extraction system composed of a thermoseparating copolymer EOPOEO and K₂HPO₄. Bromelain predominantly partitioned to the EOPOEO-rich phase and then re-extract to the top dilute phase. The recovery of enzyme activity (68.6%) and purification factor (6.53) were determined under optimum conditions. The EOPOEO-rich phase and salt were recycled, and the recovery of enzyme activity could reach up to 60%. This method has been proved to obtain highly purified and stable bromelain.     

Recovery and partial purification of thermophilic β-xylosidase derived from recombinant Bacillus megaterium MS941 by aqueous two-phase system

A polymer–salt-based aqueous two-phase system (ATPS) was developed for the effective extraction and purification of extracellular β-xylosidase from the fermentation broth of recombinant Bacillus megaterium MS941. The effect of molecular weight (MW) of polyethylene glycol (PEG), tie-line length (TLL), volume ratio (V_R), crude loading and pH on the recovery performance was evaluated. Under the optimal extraction conditions, β-xylosidase was successfully purified up to 23-fold with a recovery yield of 99% in the bottom salt-rich phase at PEG 4,000/potassium phosphate ATPS comprising TLL of 41.8, V_R of 2.3, crude loading (C_L) of 30% (w/w) at pH 6.     

Recovery of Human Interferon Alpha-2b from Recombinant Escherichia coli by Aqueous Two-Phase System

Recovery of periplasmic human recombinant interferon alpha-2b (IFN-α2b) from Escherichia coli rosetta-gami2 (DE3) using a single-step polyethylene glycol (PEG)-potassium phosphate aqueous two-phase system (ATPS) was investigated in this study. The influences of system parameters including PEG molecular weight, tie-line length, volume ratio, crude stock loading, system pH, and sodium chloride (NaCl) concentration (%, w/w) were studied. The results showed that the optimum condition to obtain the high purification factor of IFN-α2b in a single step was achieved by ATPS composed of 4% (w/w) PEG 8000, 13% (w/w) potassium phosphate, 0.5% (w/w) NaCl, 10% (w/w) crude stock, and a system pH of 6.5. A purification factor of 26.3 and recovery yield of 40.7% were obtained from optimized ATPS.     

The optimization of aqueous two‐phase extraction of lysozyme from crude hen egg white using response surface methodology

BACKGROUND: Aqueous two‐phase extraction is a versatile method for separating biological particles and macromolecules. In the present wok, the feasibility of using PEG 4000/potassium citrate aqueous two‐phase system (ATPS) for recovering and purifying lysozyme was investigated. Response surface methodology was used to determine an optimized ATPS for purification of lysozyme from crude hen egg white. RESULTS: Mathematical models concerning the purification of lysozyme from chicken egg white in polyethylene glycol 4000 (PEG 4000)/potassium citrate ATPS are established using response surface methodology. Screening experiments using fractional factorial designs show that the pH of the system significantly affects the recovery and purification of lysozyme. An optimized ATPS was proved to be at pH 5.5 and 30 °C and contained 18% (w/w) PEG, 16% (w/w) potassium citrate, 3.75% (w/w) potassium chloride (KCl). Under those conditions, the specific activity, purification factor and activity yield for lysozyme were 31100 U mg^?1, 21.11 and 103%, respectively. CONCLUSION: The PEG 4000/potassium citrate ATPS has the potential to be applied to establish bioprocesses for the primary recovery and partial purification of lysozyme. © 2012 Society of Chemical Industry     

Optimization of recovery of esterase from Serratia marcescens using combination of the solvent impregnated resin and aqueous two-phase extraction techniques

ABSTRACT

The performance of tunable aqueous polymer phase impregnated resins (TAPPIR) which is the combination of the solvent impregnated resin principle and an aqueous two-phase system for the separation of esterase from Serratia marcescens was evaluated in this study. Different molecular weight of polyethylene glycol (PEG) (2000, 4000 and 6000) at concentration ranging from 5% to 20% (w/w) and potassium citrate were used to construct the aqueous phase in TAPPIR technology. Optimum composition of PEG and salt for esterase partitioning was determined using response surface methodology. The optimum condition for the purification of esterase was impregnation of 25% (w/w) of PEG 2000 into 4 mm porous glass beads and extraction of esterase using 15% (w/w) potassium citrate at pH 8 containing 12% (w/w) crude loading with the addition of 4% (w/w) NaCl. Esterase from S. marcescens was successfully purified by the TAPPIR technology up to 5.32 of purification factor with a yield of 75.98%.     

Reverse Micellar Extraction of Bromelain from Pineapple (Ananas comosus L. Merryl) Waste: Scale-up,Reverse Micelles Characterization and Mass Transfer Studies

Scale-up studies for phase transfer mode of reverse micellar extraction are attempted for the separation and primary purification of bromelain (EC 3.4.22.33) from pineapple (Ananas comosus L. Merryl) waste. Characterization of reverse micelles and mass transfer studies for the real system has been attempted for the first time. Scale-up of the extraction process employing commercial grade surfactant cetyltrimethylammonium bromide (CTAB) and solvent isooctane resulted in purification of 2.43 fold with an activity recovery 81.3%. The reverse micellar size estimated using empirical and geometrical models indicated that the reverse micelles are large enough (R_m = 7.2–9.6 nm) to host bromelain molecules that are relatively smaller in size (～1.67 nm). The studies on the kinetics of mass transfer indicated a relatively slower rate (by ～34%) of mass transfer in case of back extraction compared to forward extraction. Process scale-up did not significantly affect the extraction efficiency whereas purity of phase components played a major role. The mass transfer across the phases was high in the initial period of mixing for both forward and back extractions.     

Partition of alkaline protease in aqueous two-phase systems of polyethylene glycol 1000 and potassium phosphate

This article presents a study of polyethylene glycol 1000 (PEG1000)/potassium phosphate aqueous two-phase systems (ATPSs) forBacillus subtilis NS99 alkaline protease extraction. The objectives were to evaluate effects of system pH (7.5, 8.5,9.5, and 10.5), and NaCl concentration (0,4,7, and 10% (w/w)) on ATPS binodal curves, effects of system pH, NaCl concentration, and tie-line length (TLL) on alkaline protease partition coefficient (K) and yield (Y%) at room temperature (30±2 ‡C). Casein hydrolysis was used for determination of alkaline protease activity. It was revealed that system pH had the slightest effect on locations of binodal curves (except at pH 10.5). In contrast, addition of NaCl appeared to have a significant effect on phase characteristics since binodal curves of systems with NaCl (4-10% (w/w)) shifted significantly towards the origin in comparison to the ones without NaCl. Increased NaCl concentration from 4 to 10% (w/w), however, showed trivial influence on locations of the binodal curves. Changes of system compositions due to variation in system pH, TLL, and NaCl concentrations obviously resulted in varied obtainable K and Y% of alkaline proteases. Longer TLL and higher pH generally resulted in higher K. In contrast, the lower NaCl concentration, the higher K. Since the same phase volume ration (1:1) was used throughout the experiments, Y% depended solely on K. The most suitable PEG1000/potassium phosphate ATPS was determined at pH 9.5, and comprised PEG1000, potassium phosphate, and NaCl 18.0,13.0, and 0% (w/w), respectively. This system resulted in considerably high K, and Y% of 20.0, and 95.1%, respectively. Information from this study will be important for further development of an ATPS extraction unit for alkaline protease recovery.     

Pineapple wastes: A potential source for bromelain extraction

This study investigates the isolation and characterization of bromelain extract from the wastes of Nang Lae and Phu Lae pineapple cultivars (economical fruits of Chiang Rai province, Thailand). The waste portions such as the peel, core, stem and crown were 29–40%, 9–10%, 2–5% and 2–4% (w/w), respectively. The extract of crown from both cultivars gave the highest proteolytic activity and protein contents, while the extract from the stem exhibited the lowest values. SDS–PAGE showed that the major protein band in the extracts was ～28 kDa. Activity staining of the crown extracts from both cultivars confirmed that the major protein band showed caseinolytic activity on the casein substrate-gel. All of the crude extracts from both cultivars gave high caseinolytic activity (>80% relative) in a board pH range (3–9). The optimum temperatures for all crude extracts were about 50–60 °C. This study founded that there is much added value into local Thailand pineapple wastes because of bromelain extraction.     

Improved recovery of B‐phycoerythrin produced by the red microalga Porphyridium cruentum

A simplified process for the primary recovery and purification of B‐phycoerythrin (BPE) from Porphyridium cruentum exploiting aqueous two‐phase systems (ATPS) and isoelectric precipitation was developed in order to reduce the number of unit operations and benefit from increased purity and yield of the protein product. Evaluation of the partitioning behaviour of BPE in polyethylene glycol (PEG)/sulphate, PEG/dextran and PEG/phosphate ATPS was carried out to determine under what conditions the BPE and contaminants concentrated into opposite phases. An additional stage of isoelectric precipitation at pH 4.0 after cell disruption resulted in an increase in purity of the target protein from the BPE crude extract and enhanced the performance of the subsequent ATPS. PEG1000/phosphate ATPS proved to be suitable after isoelectric precipitation for the recovery of highly purified (defined as absorbance ratio A_{545 nm}/A_{280 nm} > 4.0) BPE with a potential commercial value as high as US$ 50/mg. An ATPS extraction stage comprising 29.5% (w/w) PEG1000, 9.0% (w/w) phosphate, a volume ratio (V_r) equal to 1.0, a system pH of 7.0 and loaded with 40% (w/w) of the BPE extract generated by precipitation allowed BPE recovery with a purity of 4.1±0.2 and an overall product yield of 72% (w/w). The purity of BPE from the crude extract increased 5.9‐fold after isoelectric precipitation and ATPS. The results reported herein demonstrate the benefits of the practical application of isoelectric precipitation together with ATPS for the recovery and purification of BPE produced by P. cruentum as a first step in the development of a commercial purification process. Copyright © 2006 Society of Chemical Industry     

Enhancing the recovery and concentration of polyphenols from camu-camu (Myrciaria dubia H.B.K. McVaugh) by aqueous two-phase flotation and scale-up process

In this study, polyphenols obtained from camu-camu pulp residue were recovered and concentrated from aqueous two-phase flotation (ATPF) by evaluating different operating conditions, such as solvent type, pH, ammonium sulfate concentration, flotation time, air flow, and volumetric ratio. Under optimal conditions, the polyethylene glycol 400/ammonium sulfate ATPF system showed an efficiency of 81.02% and a concentration coefficient two times higher than traditional aqueous two-phase extraction. Experiments were also carried out on a semi-pilot scale, using an apparatus with a 2.5-L working volume. The results showed that the semi-pilot system was comparable to the smaller scale system.     

Bovine serum albumin partitioning in polyethylene glycol (PEG)/potassium citrate aqueous two-phase systems

The extraction and back-extraction of bovine serum albumin (BSA) have been studied by liquid–liquid extraction with poly(ethylene glycol) (PEG)/potassium citrate aqueous two-phase system (ATPS). In this work, the ATPS was examined with regard to the effects of PEG molecular weight (PEG 1000, 2000, 4000 and 6000), PEG and potassium citrate concentration, BSA concentration (C_BSA) and pH on BSA partition. The pH was found to have significant effects on BSA partition with low molecular weight PEG 1000. The yield of the BSA, 99%, was obtained in the top phase under the following conditions: 19% (w/w) PEG 1000, 20% (w/w) potassium citrate and 0.75 mg/g C_BSA at pH 7.0 and 30 °C. BSA can be re-extracted to a new citrate phase by decreasing the pH of the system with a 92% yield. The back-extraction not only separates the BSA from the polymer, but also allows the polymer to be recycled. The global yield (Y_e + Y_be) is up to 91%.     

Practical application of aqueous two‐phase systems for the development of a prototype process for c‐phycocyanin recovery from Spirulina maxima

A novel process for the recovery of c‐phycocyanin from Spirulina maxima exploiting aqueous two‐phase systems (ATPS), ultrafiltration and precipitation was developed in order to reduce the number of unit operations and benefit from an increased yield of the protein product. The evaluation of system parameters such as PEG molecular mass, concentration of PEG as well as salt, system pH and volume ratio was carried out to determine under which conditions the c‐phycocyanin and contaminants concentrate to opposite phases. PEG1450–phosphate ATPS proved to be suitable for the recovery of c‐phycocyanin because the target protein concentrated in the top phase whilst the cell debris concentrated in the bottom phase. A two‐stage ATPS process with a phase volume ratio (V_r) equal to 0.3, PEG1450 7% (w/w), phosphate 20% (w/w) and system pH of 6.5 allowed c‐phycocyanin recovery with a purity of 2.4 (estimated as the relationship of the 620 nm to 280 nm absorbances). The use of ultrafiltration (with a 30 kDa membrane cut‐off) and precipitation (with ammonium sulfate) resulted in a recovery process that produced a protein purity of 3.8 ± 0.1 and an overall product yield of 29.5% (w/w). The results reported here demonstrated the practical implementation of ATPS for the design of a prototype recovery process as a first step for the commercial purification of c‐phycocyanin produced by Spirulina maxima. © 2001 Society of Chemical Industry     

Demixing kinetics of phase systems employed for liquid-liquid extraction and correlation with system properties

The kinetics of phase demixing in liquid-liquid extraction for model systems comprising PEG 4000/potassium phosphate and t-butanol/ammonium sulfate was studied. The kinetics of demixing depicts the entire demixing pattern of phases of the phase system during and after extraction and hence the study is essential prior to design of large scale gravity phase separators. With an increase in composition, both the systems showed increase in demixing rate (decrease in demixing time). At high tie line length (TLL) and phase volume ratio <1, with salt rich phase as continuous phase, both PEG 4000/potassium phosphate and t-butanol/ammonium sulfate systems showed reduction in demixing time by 59% and 50%, respectively as compared to that at low TLL. An empirical equation proposed in the literature for rate of phase demixing was used to correlate the experimental data. The agreement was better for t-butanol/ammonium sulfate system when compared to PEG 4000/potassium phosphate system.     

Aqueous Two‐Phase Partitioning of Glucose Isomerase from Actinoplanes missouriensis in the Presence of PEG‐Derivatives and its Immobilization on Chitosan Beads

Abstract

Purification of glucose isomerase by its partitioning in a PEG‐salt aqueous two‐phase system (ATPS) in the presence of PEG derivatives has been studied. Selective partitioning of the proteins was observed towards the PEG phase containing PEG‐benzoate and PEG‐palmitate, enriching glucose isomerase in the salt phase. Cross‐current extraction in 4 stages in the presence of PEG‐palmitate gave an enrichment factor of ～5 for the enzyme. After initial purification with ATPS, glucose isomerase was immobilized on cross‐linked chitosan beads. The immobilized enzyme was stable over a wider pH range (5.2–9.0) and showed an optimum pH of 6.5     

Integrated process of extraction and purification of betanin from Opuntia ficus-indica using aqueous two-phase systems based on THF and sodium salts

This research present an integrated process for the extraction and purification of betanin from fruit of Opuntia ficus-indica. The extraction process was evaluated using different solvents (water, acetonitrile, ethanol and tetrahydrofuran), and then integrated into the purification process using aqueous two-phase systems (ATPS). The optimum conditions for extraction was with THF and the purification conditions determined to be 43 wt% of THF and 6 wt% of sodium citrate buffer (pH 5.5) at 25°C. A purification factor of 13.7 ± 0.5 fold, with a partition coefficient of betanin for salt-rich phase and the antioxidant capacity was increased ≈ 65%.     

Aqueous two-phase countercurrent distribution for the separation of c-phycocyanin and allophycocyanin from Spirulina platensis

C-phycocyanin (C-PC) and allophycocyanin (APC) with similar molecular structures were separated, respectively from Spirulina platensis cell homogenate by single extraction and multi-stage countercurrent distribution (CCD) using an aqueous two-phase system (ATPS) composed of polyethylene glycol (PEG) and potassium phosphate (KPi). The partition coefficients of C-PC and APC were 10.64 and 0.57, respectively, and the extraction selectivity of C-PC was 18.67 from 0.5% (w/w) S. platensis crude extract by single extraction using PEG6000/KPi ATPS (pH 7.0) with 34% (w/w) tie line length (TLL). In ten-stage CCD under the same ATPS extraction condition with 2% (w/w) S. platensis crude extract, the purity of C-PC increased nearly twice and the recovery of APC increased more than nine-fold compared with single extraction. The results displayed that most C-PC (82.1%) followed the mobile phase was enriched in the top phases of the last three tubes, while more APC (41%) remained in the stationary phase was enriched in the bottom phases of the first three tubes in the ten-stage CCD. Hence, aqueous two-phase CCD technology provided an effective and low cost method for C-PC and APC separation from S. platensis cell homogenate directly.     

Aqueous two‐phase systems for the recovery of a recombinant viral coat protein from Escherichia coli

In this study the use of an aqueous two‐phase system (ATPS) following the direct chemical extraction of a recombinant viral coat protein, from the cytoplasm of Escherichia coli, is evaluated. The driving force is the need to establish an economically‐viable process for the manufacture of a vaccine against human papilloma infection. The partition behaviour of recombinant L1 protein, the major structural protein of the virus, and DNA was investigated in a polyethylene glycol (PEG)–phosphate system. An evaluation of system parameters including PEG molecular mass and the concentrations of PEG and phosphate was conducted, to estimate conditions under which the L1 protein and DNA partition to opposite phases. ATPS extraction comprising a volume ratio of 1.00, PEG 1000 (18.0%(w/w)) and phosphate (15.0%(w/w)) provided the conditions for accumulation of DNA into the bottom phase and concentration of L1 protein into the opposite phase (ie partition coefficient of DNA; ln K_DNA < 0.0 and partition coefficient of L1; ln K_L1 > 2.5). The findings reported here demonstrate the potential of ATPS to recover recombinant protein released from E coli by direct chemical extraction. © 2002 Society of Chemical Industry     

Purification of β-galactosidase from recombinant Pichia pastoris using aqueous two-phase separation technique

In the current investigation, aqueous two-phase methodology with polyethylene glycol (PEG) 6000/phosphate salt has been used for single-step purification of β-galactosidase from recombinant Pichia pastoris. Optimized parameters with 12% (w/w) salt concentration, 25% (w/w) polymer concentration, 0.6 (mg/ml) protein load and 0.1 M ionic concentration resulted in a maximum of 4.7 purification fold with a 97% yield. The enzyme kinetic study of purified protein revealed V_m and K_m of 97.087 (U/mg), 0.027(U/mg), 0.07 (U/mg) and 0.7 (mM), 11.13 (mM), 10.73 (mM) with O-nitrophenyl-β-D-galactopyranoside, lactose and milk substrate, respectively.