A study on the effects of SEBS‐g‐MAH on the phase morphology and mechanical properties of polypropylene/polycarbonate/SEBS ternary polymer blends

In this work, five ternary blends based on 70% by weight (wt %) of polypropylene (PP) with 30% wt of polycarbonate (PC)/poly(styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene)(SEBS) dispersed phase consists of 15 wt % PC and 15 wt % reactive (maleic anhydride grafted) and nonreactive SEBS mixtures at various ratios were prepared in a co‐rotating twin screw extruder. scanning electron microscopy (SEM) micrographs showed that the blends containing only nonreactive SEBS exhibited a fine dispersion of core‐shell particles. With decreasing the SEBS/SEBS‐g‐Maleic Anhydride (MAH) weight ratio, the morphology changed from the core‐shell particles to a mixed of core‐shell, rod‐like and individual particles. This variation in phase morphology affected the thermal and mechanical properties of the blends. DSC results showed that the blends containing only nonreactive SEBS exhibited a minimum in degree of crystallinity due to the homogeneous nucleation of core‐shell particles. Mechanical testing showed that in the SEBS/SEBS‐g‐MAH weight ratio of 50/50, the modulus and impact strength increased compared with the PP matrix while the yield stress had minimum difference with that of PP matrix. These effects could be attributed to the formation of those especial microstructures revealed by the SEM studies. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Synergetic toughness and morphology of poly(propylene)/nylon 11/maleated ethylene‐propylene diene copolymer blends

Polypropylene (PP)/nylon 11/maleated ethylene‐propylene‐diene rubber (EPDM‐g‐MAH) ternary polymer blends were prepared via melt blending in a corotating twin‐screw extruder. The effect of nylon 11 and EPDM‐g‐MAH on the phase morphology and mechanical properties was investigated. Scanning electron microscopy observation revealed that there was apparent phase separation for PP/EPDM‐g‐MAH binary blends at the level of 10 wt % maleated elastomer. For the PP/nylon 11/EPDM‐g‐MAH ternary blends, the dispersed phase morphology of the maleated elastomer was hardly affected by the addition of nylon 11, whereas the reduced dispersed phase domains of nylon 11 were observed with the increasing maleated elastomer loading. Furthermore, a core‐shell structure, in which nylon 11 as a rigid core was surrounded by a soft EPDM‐g‐MAH shell, was formed in the case of 10 wt % nylon 11 and higher EPDM‐g‐MAH concentration. In general, the results of mechanical property measurement showed that the ternary blends exhibited inferior tensile strength in comparison with the PP matrix, but superior toughness. Especially low‐temperature impact strength was obtained. The toughening mechanism was discussed with reference to the phase morphology. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Interface modification of compatibilized polyethylene terephthalate/polypropylene blends: Effect of compatibilization on thermomechanical properties and thermal stability

Polyethylene terephthalate (PET) and polypropylene (PP) are incompatible thermoplastics because of differences in chemical structure and polarity, hence their blends possess inferior mechanical and thermal properties. Compatibilization with a suitable block/graft copolymer is one way to improve the mechanical and thermal properties of the PET/PP blend. In this study, the toughness, dynamic mechanical analysis (DMA), and thermogravimetric analysis (TGA) of PET/PP blends were investigated as a function of different content of styrene‐ethylene‐butylene‐styrene‐g‐maleic anhydride (SEBS‐g‐MAH) compatibilizer. PET, PP, and SEBS‐g‐MAH were melt‐blended in a single step using the counter rotating twin screw extruder with compatibilizer concentrations of 0, 5, 10, and 15 phr, respectively. The impact strength of compatibilized blend with 10 phr SEBS‐g‐MAH increased by 300% compared to the uncompatibilized blend. Scanning electron microscope (SEM) micrographs show that the addition of 10 phr SEBS‐g‐MAH compatibilizer into the PET/PP blends decreased the particle size of the dispersed PP phase to the minimum level. The improvement of the storage modulus and the decrease in the glass transition temperature of the PET phase indicated an interaction among the blend components. Thermal stability of the PET/PP blends was significantly improved because of the addition of SEBS‐g‐MAH. J. VINYL ADDIT. TECHNOL., 23:45–54, 2017. © 2015 Society of Plastics Engineers     

Impact,thermal, and morphological properties of functionalized rubber toughened‐poly(ethylene terephthalate) nanocomposites

In this study, poly(ethylene terephthalate)/organo‐montmorillonite (PET/OMMT) nanocomposites were melt‐compounded using twin screw extruder followed by injection molding. Maleic anhydride grafted styrene‐ethylene/butylene‐styrene (SEBS‐g‐MAH) was used to improve the impact properties of the PET/OMMT nanocomposites. The notched and un‐notched impact strength of PET/OMMT nanocomposites increased at about 2.5 times and 5.5 times by the addition of 5 wt % of SEBS‐g‐MAH. Atomic force microscopy (AFM) scans were taken from the polished surface of both PET/OMMT and SEBS‐g‐MAH toughened PET/OMMT nanocomposites. The addition of SEBS‐g‐MAH altered the phase structure and clay dispersion in PET matrix. It was found that some of the OMMT silicate layers were encapsulated by SEBS‐g‐MAH. Further, the addition of SEBS‐g‐MAH decreased the degree of crystallinity of the PET/OMMT nanocomposites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Mechanical,thermal, and morphological properties of injection molded poly(lactic acid)/SEBS‐g‐MAH/organo‐montmorillonite nanocomposites

Poly(lactic acid)/organo‐montmorillonite (PLA/OMMT) nanocomposites toughened with maleated styrene‐ethylene/butylene‐styrene (SEBS‐g‐MAH) were prepared by melt‐compounding using co‐rotating twin‐screw extruder followed by injection molding. The dispersibility and intercalation/exfoliation of OMMT in PLA was characterized using X‐ray diffraction and transmission electron microscopy (TEM). The mechanical properties of the PLA nanocomposites was investigated by tensile and Izod impact tests. Thermogravimetric analyzer and differential scanning calorimeter were used to study the thermal behaviors of the nanocomposite. The homogenous dispersion of the OMMT silicate layers and SEBS‐g‐MAH encapsulated OMMT layered silicate can be observed from TEM. Impact strength and elongation at break of the PLA nanocomposites was enhanced significantly by the addition of SEBS‐g‐MAH. Thermal stability of the PLA/OMMT nanocomposites was improved in the presence of SEBS‐g‐MAH. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Effects of addition of functionalized SEBS on rheological,mechanical, and tribological properties of polyamide 6 nanocomposites

The effects of the addition of styrene‐ethylene/butylene‐styrene copolymer (SEBS) with various functionalized groups on the rheological, mechanical, and tribological properties on polyamide 6 nanocomposite filled with layered silicate (PA6/Clay) were investigated. Four types of SEBS: unmodified SEBS (SEBS), maleic anhydride grafted SEBS (SEBS‐g‐MA), amine group grafted SEBS (SEBS‐g‐NH₂), and carboxyl group grafted SEBS (SEBS‐g‐COOH) were added with PA6/Clay nanocomposite to prepare various polymer blends. These polymer blends were extruded by a twin screw extruder and injection molded. Dynamic viscoelastic properties of these blends in the molten state and their tensile, impact, and tribological properties were evaluated. The viscoelastic properties were found to increase with the addition of SEBS and were highly influenced by the types of functionalized groups contained. Influence of the addition of SEBS on the mechanical properties of these systems differed for each mechanical property. Although the tensile properties decreased with SEBS, Izod impact properties improved with the addition of various functionalized SEBS. These mechanical properties and viscoelastic properties correlated closely with the size of dispersed SEBS particles and interparticle distance. The tribological properties also improved with the addition of SEBS, and the influence of the amount added was higher than the type of SEBS used. POLYM. ENG. SCI., 2010. © 2009 Society of Plastics Engineers     

Studies on morphology and thermomechanical performance of ABS/PC/organoclay hybrids

In the present research, poly(acrylonitrile‐butadiene‐styrene)/polycarbonate (ABS/PC) blends were prepared in a twin screw extruder. An attempt to reinforce and promote compatibility of the above systems was made by the incorporation of organically modified montmorillonite (OMMT, Cloisite 30B), as well as by the addition of compatibilizer (ABS grafted with maleic anhydride, ABS‐g‐MAH), and the effect of those treatments on the morphology, thermal transitions, rheological, and mechanical properties of the above blends was evaluated. The addition of compatibilizer in ABS/PC blends does not significantly affect the glass transition temperature (T_g) of SAN and PC phases, whereas the incorporation of Cloisite 30B decreases slightly the T_g values of SAN and, more significantly, that of PC in compatibilized and uncompatibilized blends. The T_g of PB phase remains almost unaffected in all the examined systems. The obtained results suggest partial dissolution of the polymeric components of the blend and, therefore, a modified Fox equation was used to assess the amount of PC dissolved in the SAN phase of ABS and vice versa.Reinforcing with OMMT enhances the miscibility of ABS and PC phases in ABS/PC blends and gives the best performance in terms of tensile strength, modulus of elasticity, and storage modulus, especially in 50/50 (w/w) ABS/PC blends. The addition of ABS‐g‐MAH compatibilizer, despite the improvement of intercalation process in organoclay/ABS/PC nanocomposites, did not seem to have any substantial effect on the mechanical properties of the examined blends. POLYM. COMPOS., 35:1395–1407, 2014. © 2013 Society of Plastics Engineers     

The effect of compatibilizers and organically modified nanoclay on the morphology and performance properties of poly(acrylonitrile–butadiene–styrene)/polypropylene blends

In this study, poly(acrylonitrile–butadiene–styrene)/polypropylene (ABS/PP) blends with various compositions were prepared by melt intercalation in a twin‐screw extruder. Modifications of the above blends were performed by using organically modified montmorillonite (OMMT, Cloisite 30B) reinforcement as well as two types of compatibilizers, namely polypropylene grafted with maleic anhydride (PP‐g‐MAH) and ABS grafted with maleic anhydride (ABS‐g‐MAH). Increasing the PP content in ABS matrix seems to increase the melt flow and thermal stability of their blends, whereas a deterioration of the tensile properties was recorded. On the other hand, the addition of ABS to PP promotes the formation of the β‐crystalline phase, which became maximum at 30 wt% ABS concentration, and increases the crystallization temperature (T_c) of PP. A tendency for increase of T_c was also recorded by incorporation of the above compatibilizers, whereas the glass transition temperature (T_g) of PP and SAN phase in ABS was reduced. Regarding the Young's modulus, the greatest improvement was observed in pure ABS/PP blends containing organically modified nanoclay. However, in reinforced pure PP, the use of compatibilizers is recommended in order to improve the elastic modulus. The addition of OMMT to noncompatibilized and compatibilized ABS/PP blends significantly improves their storage modulus. POLYM. ENG. SCI., 56:458–468, 2016. © 2016 Society of Plastics Engineers     

Crystallization behavior of PP/PP‐g‐MAH/GFR PA66 blends: Establishment of their continuous‐cooling‐transformation of relative crystallinity diagrams

Polypropylene/polypropylene‐grafted‐maleic anhydride/glass fiber reinforced polyamide 66 (PP/PP‐g‐MAH/GFR PA 66) blends‐composites with and without the addition of polypropylene‐grafted‐maleic anhydride (PP‐g‐MAH) were prepared in a twin screw extruder. The effect of the compatibilizer on the thermal properties and crystallization behavior was determined using differential scanning calorimetry analysis. The hold time was set to be equal to 5 min at 290°C. These conditions are necessary to eliminate the thermomechanical history in the molten state. The crystallization under nonisothermal conditions and the plot of Continuous‐Cooling‐Transformation of relative crystallinity diagrams of both PP and PA 66 components proves that PP is significantly affected by the presence of PP‐g‐MAH. From the results it is found that an abrupt change is observed at 2.5 wt % of PP‐g‐MAH as a compatibilizer and then levels off. In these blends, concurrent crystallization behavior was not observed for GFR PA66. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 1620–1626, 2007     

Compatibilization of polypropylene/Poly(acrylonitrile‐butadiene‐styrene) blends by polypropylene‐graft‐cardanol

The polypropylene‐graft‐cardanol (PP‐g‐cardanol) was prepared by reactive extrusion with polypropylene (PP) and natural renewable cardanol which could increase the interfacial energy of PP and inhibit the degradation of PP during the process of reactive extrusion and usage. In this article, PP‐g‐cardanol and polypropylene‐graft‐maleic anhydride (PP‐g‐MAH) were used as compatibilizers of the polypropylene (PP)/poly(acrylonitrile‐butadiene‐styrene) (ABS) blends. PP/ABS (70/30, wt %) blends with PP‐g‐cardanol and PP‐g‐MAH were prepared by a corotating twin‐screw extruder. From the results of morphological studies, the droplet size of ABS was minimized to 1.93 and 2.01 μm when the content of PP‐g‐cardanol and PP‐g‐MAH up to 5 and 7 phr, respectively. The results of mechanical testing showed that the tensile strength, impact strength and flexural strength of PP/ABS (70/30) blends increase with the increasing of PP‐g‐cardanol content up to 5 phr. The complex viscosity of PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol showed the highest value. Moreover, the change of impact strength and tensile strength of PP/ABS (70/30) blends were investigated by accelerated degradation testing. After 4 accelerated degradation cycles, the impact strength of the PP/ABS (70/30) blends with 5 phr PP‐g‐cardanol decrease less than 6%, but PP/ABS (70/30) blends with 5 phr PP‐g‐MAH and without compatibilizer decrease as much as 12% and 32%, respectively. The tensile strength of PP/ABS (70/30) blends has a similar tendency to that of impact strength. The above results indicated that PP‐g‐cardanol could be used as an impact modifier and a good compatibilizer, which also exhibited better stability performance during accelerated degradation testing. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41315.     

Dynamic reaction inside co‐rotating twin screw extruder. I. Truck tire model material/polypropylene blends

Waste ground rubber tire (WGRT) is a complex composite containing various elastomers, carbon black, zinc oxide, stearic acid, processing oils, and other curatives. Most of the waste ground rubber tire is composed of mainly natural rubber (NR) and styrene butadiene rubber (SBR) in varying proportions. Blending it with other thermoplastic materials is difficult due to the inherent thermodynamic incompatibility. But, the compatibility can be increased by making the reactive sites in WGRT with suitable chemicals under optimum condition of shearing inside a twin screw extruder and it is said to undergo a dynamic reaction inside the extruder. To understand the mechanism of dynamic reaction process of a rubber/polyolefin blend, the blending of a truck tire model material rubber with polyolefin was first tried before it was applied to waste WGRT material. It was observed that the blends of a truck tire model rubber material and PP thermoplastic are physical mixture of two incompatible polymers in which a continuous plastic phase is largely responsible for the tensile properties. The rubber particles are the dispersed phase. The large particle size and the poor adhesion of these rubber particles are believed to be liable for the poor tensile properties. In case of blends of truck tire model material with isotactic polypropylene the tensile properties are found to be lower than that of its PP‐g‐MA counterpart which can be attributed to the reaction of the MA with the carbon black particles. A schematic representation of the possible interactions has been proposed. The effect of addition of compatibilizers such as SEBS and SEBS‐g‐MA has also been studied. The tensile and TGA studies indicate that the polarity of SEBS and SEBS‐g‐MA induces an increase in the performance characteristics for both types of polyolefins but the intensity of this increase is higher in the PP‐g‐MA based blends. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 106: 3193–3208, 2007     

Melt rheology and properties of compatibilized recycled poly(ethylene terephthalate)/(styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer blends

Blends of recycled poly(ethylene terephthalate) (R‐PET) and (styrene‐ethylene‐ethylene‐propylene‐styrene) block copolymer (SEEPS) compatibilized with (maleic anhydride)‐grafted‐styrene‐ethylene‐butylene‐styrene (SEBS‐g‐MAH) were prepared by melt blending. The compatibilizing effects of SEBS‐g‐MAH were investigated systematically by study of the morphology, linear viscoelastic behavior, and thermal and mechanical properties of the blends. The results show that there is good agreement between the results obtained by rheological measurement and morphological analysis. The rheological test shows that the melt elasticity and melt strength of the blends increase with the addition of SEBS‐g‐MAH. The Cole‐Cole plots and van Gurp‐Palmen plots confirm the compatibilizing effect of SEBS‐g‐MAH. However, the Palierne model fails to predict the linear viscoelastic properties of the blends. The morphology observation shows that all blends exhibit a droplet‐matrix morphology. In addition, the SEEPS particle size in the (R‐PET)/SEEPS blends is significantly decreased and dispersed uniformly by the addition of SEBS‐g‐MAH. Differential scanning calorimeter analysis shows that the crystallization behavior of R‐PET is restricted by the incorporation of SEEPS, whereas the addition of SEBS‐g‐MAH improves the crystallization behavior of R‐PET compared with that of uncompatibilized (R‐PET)/SEEPS blends. The Charpy impact strength of the blends shows the highest value at SEBS‐g‐MAH content of 10%, which is about 210% higher than that of pure R‐PET. J. VINYL ADDIT. TECHNOL., 22:342–349, 2016. © 2014 Society of Plastics Engineers     

Effect of poly [styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] (SEBS) and maleic anhydride‐grafted SEBS triblock copolymers in immiscible blends of (polyamide‐6)/polycarbonate: Morphology‐mechanical properties relationships

The effects of using maleated poly[styrene‐b‐(ethylene‐co‐butylene)‐b‐styrene] triblock copolymer (SEBS‐g‐MAH) and unmodified SEBS (unSEBS) on the phase morphology and mechanical properties of immiscible polymer blends of polyamide‐6 (PA‐6) and polycarbonate (PC) are investigated. Different binary, ternary, and quaternary blends were prepared by using a Brabender® co‐rotating twin‐screw extruder. The weight ratio of unSEBS to SEBS‐g‐MAH was changed to probe the phase morphology and mechanical properties. The results revealed that the mechanical properties of (PA‐6)/PC/(unSEBS/SEBS‐g‐MAH) blends were considerably governed by the unSEBS to SEBS‐g‐MAH weight ratio. Morphological investigation based on the spreading coefficient concept confirmed the results of scanning electron microscopy, indicating encapsulation of unSEBS domains around the PC core‐forming component in the presence of reactive SEBS‐g‐MAH precursor. Moreover, larger unSEBS‐PC composite droplets appeared throughout PA‐6 matrix upon increasing the ratio of unSEBS to SEBS‐g‐MAH, until reaching a maximum value. In the case of the (PA‐6)/PC blend compatibilized with a 50/50 combination of unSEBS and SEBS‐g‐MAH, the highest mechanical properties, i.e., tensile strength, impact resistance, and strain at break, were achieved owing to compatibilizing effect of virgin and maleated SEBS constituents. J. VINYL ADDIT. TECHNOL., 21:245–252, 2015. © 2014 Society of Plastics Engineers     

Toughening of polypropylene with styrene/ethylene‐butylene/styrene triblock copolymer: Effects of reactive and nonreactive compatibilization

The effects of the compatibilization on the toughening of polypropylene (PP) by melt blending with styrene/ethylene‐butylene/styrene triblock copolymer (SEBS) in a twin‐screw extruder were investigated. The compatibilizers used were an SEBS functionalized with maleic anhydride, a PP functionalized with acrylic acid, and a bifunctional compound, p‐phenylenediamine (PPD). The effects of the compatibilization were evaluated through the mechanical properties and by the determination of the phase morphology of the blends by scanning electron microscopy. Reactive compatibilized blends show up to a 30‐fold increase in impact strength compared to neat PP, which was likely to have been due to the reaction of the bifunctional compound (PPD) with the acid acrylic and maleic anhydride groups, which rendered both morphological and mechanical stability to these blends. The addition of the PPD to the blends significantly changed their phase morphologies, leading to larger dispersed particles' average diameters, probably due to the morphological stabilization at the initial processing steps during extrusion, with the occurrence of the chemical reactions. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1081–1094, 2003     

Dynamic reaction inside co‐rotating twin screw extruder. II. Waste ground rubber tire powder/polypropylene blends

In this article, dynamic reaction of waste ground rubber tire powder/PP blends with compatibilizers is extended to commercially available waste rubber Viz. Ground rubber tire and PP for the possibility of getting recycled material with good mechanical properties. In the first part of the article it was shown that the compatibility of model material/PP blends has greatly improved. In this article, extensive studies have been carried out to study the effect of compatibilizers, in‐situ compatibilization of immiscible waste ground rubber tire (WGRT) powder/polyolefin blends of various concentrations was investigated by means of extrusion process using a co‐rotating twin screw extruder. It was observed that addition of small amounts of compatibilizers like SEBS‐g‐MA to the blends of WGRT and PP‐g‐MA can result in better mechanical properties than the blends with isotactic PP. The blends of WGRT powder and PP‐g‐MA with compatibilizer have better adhesion than those of isotactic PP blends as revealed by the morphological studies using AFM and SEM. The betterment in properties can be attributed to the presence of functional group, maleic anhydride in PP‐g‐MA. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Mechanical properties and morphology of PP/ABS blends compatibilized with PP‐g‐2‐HEMA

Polypropylene (PP) and acrylonitrile–butadiene–styrene blends of different composition were prepared using a single‐screw extruder. The binary blend of PP/ABS was observed to be incompatible and shows poor mechanical properties. PP‐g‐2‐hydroxyethyl methacrylate (2‐HEMA) was used as a compatibilizer for the PP/ABS blends. The ternary compatibilized blends of PP/ABS/PP‐g‐2‐HEMA showed improvement in the mechanical properties. Electron micrographs of these blends showed a homogeneous and finer distribution of the dispersed phase. The mechanical performance increased particularly in the PP‐rich blend. The 2.5‐phr (part per hundred of resin) compatibilizer was observed to bring improvement to the properties. The suitability of various existing theoretical models for the predication of the tensile moduli of these blends was examined. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 72–78, 2003     

Rheological behaviors of glass bead‐ and wollastonite‐filled polypropylene composites modified with thermoplastic elastomers

Steady‐ and oscillatory‐shear rheological behaviors of polypropylene/glass bead (PP/GB) and PP/wollastonite (PP/W) melts modified with thermoplastic elastomers, poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) copolymer (SEBS) and the corresponding block copolymer grafted with maleic anhydride (SEBS‐g‐MA), were examined by means of a parallel‐plate rheometer. With adding the elastomers (SEBS and SEBS‐g‐MA) and fillers (spherical GB and acicular W) to PP, viscosity especially at low shear rates and shear‐thinning flow behavior at high shear rates were pronounced as evidenced quantitatively by Carreau–Yasuda (CY) parameters, but Cox–Merz analogy became weakened. Besides, melt‐elasticity in terminal region and relaxation time (t_c) in crossing point increased, indicating an enhancement in quasi‐solid behavior of molten PP. Comparing with the elastomers, rheological behaviors of molten PP were more influenced with adding the rigid fillers, especially with W due to distinct acicular shape of W particles. SEBS‐g‐MA elastomer more affected rheological behaviors of the ternary composites than SEBS elastomer, implying that SEBS elastomer and the filler particles behaved individually (i.e., development of separate microstructure) in (PP/GB)/SEBS and (PP/W)/SEBS ternary composites, but core‐shell microstructure developed with strong interfacial adhesion by adding SEBS‐g‐MA elastomer, and the filler particles encapsulated with the thick SEBS‐g‐MA elastomer interlayer (i.e., core‐shell particles) acted like neither big elastomer particles nor like individual rigid particles in melt‐state. Moreover, effects of SEBS‐g‐MA elastomer reached a maximum on rheological behaviors of (PP/W)/SEBS‐g‐MA ternary composite, indicating a synergy between core‐shell microstructure and acicular W particles. Correlations between oscillatory‐shear flow properties and microstructures of the blends and composites were evaluated using Cole–Cole (CC), Han–Chuang (HC), and van Gurp–Palmen (vGP) plots. COMPOS., 2012. © 2012 Society of Plastics     

Tough polyamide 6/core–shell blends prepared via in situ anionic polymerization of ε‐caprolactam by reactive extrusion

In this study, the molten ε‐caprolactam (CL) solution of maleated styrene‐ethylene/butylene‐styrene block copolymer (SEBS‐g‐MA) and polystyrene (PS) containing catalyst and activator were introduced into a twin screw extruder, and polyamide 6 (PA6)/SEBS/PS blends were successfully prepared via anionic polymerization of CL by reactive extrusion. The mechanical properties measurements indicated that both the elongation at break and notched Izod impact strength of PA6/SEBS/PS (85/10/5) blends were improved distinctly with slight loss of tensile and flexural strength as compared to that of pure PA6. The images of transmission electron microscopy showed that a core–shell structure with PS core and poly (ethene‐co‐1‐butene) (PEB) shell was formed within the PA6 matrix. Fourier transform infrared was used to investigate the formation mechanisms of the core–shell structure. POLYM. ENG. SCI., 53:2705–2710, 2013. © 2013 Society of Plastics Engineers     

Process–structure–property relationship in ternary short‐glass‐fiber/elastomer/polypropylene composites

Short‐glass‐fiber (SGF)‐reinforced polypropylene (PP) composites toughened with a styrene/ethylene butylene/styrene (SEBS) triblock copolymer were injection molded after extrusion. Furthermore, a maleic anhydride (MA)‐grafted SEBS copolymer (SEBS‐g‐MA) was used as an impact modifier and compatibilizer. The effects of the processing conditions and compatibilizer on the microstructure and tensile and impact performance of the hybrid composites were investigated. In the route 1 fabrication process, SGF, PP, and SEBS were blended in an extruder twice, and this was followed by injection molding. In route 2, or the sequential blending process, the elastomer and PP were mixed thoroughly before the addition of SGF. In other words, either PP and SEBS or PP and SEBS‐g‐MA pellets were premixed in an extruder. The produced pellets were then blended with SGF in the extruder, and this was followed by injection molding. The SGF/SEBS‐g‐MA/PP hybrid fabricated by the route 2 process exhibited the highest modulus, yield stress, tensile stress at break, Izod impact energy, and Charpy drop weight impact strength among the composites investigated. This was due to the formation of a homogeneous SEBS elastomeric interlayer at the SGF and matrix interface of the SGF/SEBS‐g‐MA/PP hybrid. This SEBS rubbery layer enhanced the interfacial bonding between SGF and the matrix of the SGF/SEBS‐g‐MA/PP hybrid. The correlations between the processing, microstructure, and properties of the hybrids were investigated. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1384–1392, 2003     

Characteristics of impact modified polystyrene/organoclay nanocomposites

The poor impact resistance of Polystyrene (PS) was enhanced by the addition of elastomeric material, SEBS‐g‐MA. To prevent the reduction in strength and stiffness, organoclay Cloisite® 25A was used as filler and introduced into the matrix by a corotating twin screw extruder. Throughout the study, the clay content was kept at 2 wt%, whereas the content of SEBS‐g‐MA was varied between 5 and 40 wt%. It was found that Cloisite® 25A displays well dispersion in the ternary nanocomposites and the degree of dispersion increases with the elastomer content. The elastomeric phase has a greater viscosity than pure PS. Thus, as expected, at low elastomer contents, it forms the dispersed phase in the matrix as droplets. Transmission electron microscopy results show that the clay layers reside at the interphase between PS and elastomer and also inside the elastomeric phase. Owing to the location of the clay particles, the average elastomer domain size in ternary nanocomposites are found to be greater than that in the relative binary blends of PS‐(SEBS‐g‐MA). Moreover, with the organoclay addition, phase inversion point shifts to lower elastomer contents. The mechanical test results showed that the nanocomposites containing 15 and 20 wt% SEBS‐g‐MA have the optimum average domain size that results in high‐impact strength values without deteriorating the tensile properties. POLYM. COMPOS., 31:1853–1861, 2010. © 2010 Society of Plastics Engineers.