Solid polymer electrolytes V: microstructure and ionic conductivity of epoxide-crosslinked polyether networks doped with LiClO4

A crosslinked polyether network was prepared from poly(ethylene glycol) diglycidyl ether (PEGDE) cured with poly(propylene oxide) polyamine. Significant interactions between ions and polymer host have been observed for the crosslinked polyether network in the presence of LiClO₄ by means of FT-IR, DSC, TGA, and ⁷Li MAS solid-state NMR. Thermal stability and ionic conductivity of these complexes were also investigated by TGA and AC impedance measurements. The results of FT-IR, DSC, TGA and ⁷Li MAS solid-state NMR measurements indicate the formation of different types of complexes through the interaction of ions with different coordination sites of polymer electrolyte networks. The dependence of ionic conductivity was investigated as a function of temperature, LiClO₄ concentration and the molecular weight of polyether curing agents. It is observed that the behavior of ion transport follows the empirical Vogel-Tamman-Fulcher (VTF) type relationship for all the samples, implying the diffusion of charge carrier is assisted by the segmental motions of polymer chains. Moreover, the conductivity is also correlated with the interactions between ions and polymer host, and the maximum ionic conductivity occurs at the LiClO₄ concentration of [O]/[Li⁺]=15.     

Structure and ionic conductive properties of polydioxolane–polyurethane‐based electrolytes

A series of polyurethanes (PUs) with different polyether soft segments [polydioxolane (PDXL), polyethylene glycol (PEG), or PDXL/PEG] were synthesized successfully, and solid polymer electrolytes based on PU/LiClO₄ complexes were prepared. The relations between structure and the ionic conductive properties of the PU‐based electrolytes were investigated by means of Fourier transform infrared spectroscopy, differential scanning calorimetry, dynamic mechanical analysis, and complex impedance analysis. Results showed that the glass‐transition temperature (T_g) of PDXL–PU was lower than that of PEG–PU. Doped lithium perchlorate (LiClO₄) salt could be dissolved well in soft segments of PDXL–PU. The ionic conductivity of the PDXL–PU/LiClO₄ complex could reach a value of 2 × 10^?5 S/cm at room temperature without the addition of an organic plasticizer. The system with PDXL/PEG as a soft segment had a higher T_g and a lower ionic conductivity than the one with PDXL as a soft segment. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 103–111, 2002     

LiClO4 salt concentration effect on the properties of PVC‐modified low molecular weight LENR50‐based solid polymer electrolyte

A work was carried out on a solid polymeric electrolyte system comprising blends of poly (vinyl chloride) and liquid 50% epoxidized natural rubber (LENR50) as a polymer host with LiClO₄ as a salt and prepared by solution casting technique. In this paper, the main study was the effect of LiClO₄ salt concentration on the electrolyte properties. The effect of the salt on the electrolyte properties was characterized and analyzed with impedance spectroscopy (EIS), X‐ray diffraction (XRD), differential scanning calorimeter (DSC), and scanning electron microscopy (SEM). The EIS result showed that highest ionic conductivity was obtained at 30 wt % salt with a value of 2.3 × 10^?8 S cm^?1. The XRD results revealed that the LiClO₄ salt was fully complexed within the polymer host as no sharp peaks were observed. However, above 30 wt % of salt, some sharp peaks were observed. This phenomenon was caused by the association of ions. Meanwhile, DSC analysis showed that T_g increased as the salt content increased. This implied that LiClO₄ salt had interaction with polymer host by forming coordination bond. The morphologies' studies showed that good homogeneity and compatibility of the electrolyte were achieved. Upon the addition of the salt, formation of micropores occurred. It was noted that micropores which aid in mobility of ions in the electrolyte system has increased the ionic conductivity. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

The effect of the length of the oxyethylene chain on the conductivity of the polyurethaneurea electrolyte

Polyurethaneureas (PUU), which were synthesized from 4,4′-diphenylmethane diisocyanate (MDI), poly(ethylene glycol) (PEG), and 3,5-diaminobanzoic acid (DABA), were used as polyelectrolytes in this study. Differential scanning calorimetry (DSC) and Fourier transform infrared spectroscopy (FT-IR) were used to monitor the effect of the various kinds of PEG on the changes in morphology of PUU electrolytes corresponding to the concentration of lithium perchlorate (LiClO₄) dopants. The results of DSC and FT-IR indicate the Li⁺ ions coordinate with the soft and hard segments. Additionally, the crystallinity of the PEG soft segment and the ordered hydrogen-bonded urea carbonyl groups decreased with increasing salt concentration. Impedance spectroscopy (IS) measurements show that the PUU electrolyte with the high phase separation degree has the high ionic conductivity. The hard-segment T_g and the soft-segment T_m influence the conductivity behavior of polyelectrolytes with increasing measurement temperature.     

Physical and electrochemical properties of low molecular weight poly(ethylene glycol)‐bridged polysilsesquioxane organic–inorganic composite electrolytes via sol–gel process

A new class of ionic conducting organic/inorganic hybrid composite electrolyte with high conductivity, better electrochemical stability and mechanical behavior was prepared through the sol–gel processing between ethylene‐bridged polysilsesquioxane and poly(ethylene glycol) (PEG). The composite electrolyte with 0.05 LiClO₄ per PEG repeat unit has the best conductivity up to 10^?4 S/cm at room temperature with the transference number up to 0.48 and an electrochemical stability window as high as 5.5 V versus Li/Li⁺. Moreover, the effect of the PEG chain length on the properties of the composite electrolyte has also been studied. The interactions between ions and polymer have also been investigated for the composite electrolyte in the presence of LiClO₄ by means of FTIR, DSC, and TGA. The results indicated the interaction of Li⁺ ions with the ether oxygen of the PEG, and the formation of transient crosslinking with LiClO₄, resulting in an increase of the T_g of the composite electrolyte. The VTF‐type behavior of the ionic conductivity implied that the diffusion of the charge carriers was assisted by the segmental motions of the polymer chains. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 103: 2752–2758, 2007     

Ionic transport behavior in poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) and LiClO4 complex

The effect of LiClO₄ on the ionic transport behavior in poly(ethylene oxide)₂₀-poly(propylene oxide)₇₀-poly(ethylene oxide)₂₀ (P123) polymer electrolyte was studied. Its conductivity reaches maximum as molar ratio between ether O atoms and lithium ions [n(O)/n(Li)] equals 8. The results show that LiClO₄ could interact with P123 well and has impacts on polymer organization and chain dynamics. As LiClO₄ concentration decreases, the glass transition temperature (T_g) decreases and the free ion percentage increases. The tendency of conductivity with LiClO₄ concentration is the result of competing effects between polymer chain mobility and free charge carrier concentration.     

The effect of EPIDA units on the conductivity of poly(ethylene glycol)-4,4′-diphenylmethane diisocyanate-EPIDA polyurethane electrolytes

Novel thermoplastic polyurethanes with chelating groups were synthesized from 4,4′-diphenylmethane diisocyanate (MDI), poly(ethylene glycol) (PEG), and EP-IDA. Differential scanning calorimetry (DSC), fourier transform infrared spectroscopy (FT-IR), and impedance spectroscopy (IS) were used to monitor changes in the morphology of these polyurethanes with the concentration of lithium perchlorate (LiClO₄) dopants. Adding the salt significantly changes the FTIR spectrum of the polyurethane, indicating an interaction between the lithium cation within the urethane group and the chelating group. The soft segment T_g increases with LiClO₄ concentration, as determined by DSC, indicating that solubility of the lithium cation in the host polyurethane increases with the chelating groups. IS shows that the bulk conductivity reaches a maximum as the salt concentration is increased. One of the investigated polyurethane electrolytes has an ionic conductivity as high as ∼10⁻⁶ S cm⁻¹ at room temperature.     

The study on the conductivity and morphology of polyurethaneurea electrolytes based on poly(ethylene glycol) 2000 and LiClO4

Polyurethaneureas (PUU), which were synthesized from 4,4′-diphenylmethane diisocyanate (MDI), poly(ethylene glycol) (PEG, MW=2000), and 3,5-diaminobenzoic acid, were used as the matrix of the polyelectrolytes in this study. Differential scanning calorimetry (DSC), Fourier-transform infrared spectroscopy (FT-IR), and ⁷Li magic angle spinning (MAS) solid-state NMR were used to monitor changes in the morphology of PUU electrolytes corresponding to the concentration of lithium perchlorate (LiClO₄) dopants. The results of DSC and FT-IR indicate the different polymer complexes formed by the interaction of the Li⁺ ions with the different coordination sites of PUU. The ⁷Li MAS solid-state NMR investigation of the PUU electrolytes points out that two different Li⁺ environments exist at lower temperature. The results of DSC and the ⁷Li MAS solid-state NMR show that Li⁺ ions are preferentially coordinated to the ether oxygen of the PEG soft-segment when the salt concentration is below 0.1 mmol LiClO₄(gPUU)⁻¹. Impedance spectroscopy measurements show that the conductivity behavior followed the Arrhenius equation and was influenced by the hard-segment T_g. One of the PUU electrolytes under the investigation has an ionic conductivity as high as 3.0×10⁻⁵ S cm⁻¹ at 30 °C.     

Study on preparation and properties of gel polymer electrolytes based on comb-like copolymer matrix of poly(ethylene glycol) monomethylether grafted carboxylated butadiene-acrylonitrile rubber

A novel kind of gel polymer electrolytes (GPE) based on comb-like copolymers of poly(ethylene glycol) monomethylether (mPEG) grafted carboxylated butadiene-acrylonitrile rubber (XNBR) were prepared by introducing ionic liquids and LiClO₄ into polymer framework. FTIR spectra confirmed the grafting of mPEG to XNBR as side chains, and the content of grafted mPEG were calculated from the integral area of related peaks in ¹ H NMR spectra. Such grafted copolymer based GPE with ionic liquids as solvent showed higher ionic conductivity and reached a maximum ionic conductivity of 1.64?×?10^?3?S/cm (30?°C) in the experimental range, because the copolymers performed better polymer chain flexibility, which could be concluded from the decrease of T _g and crystallinity through DSC analysis. The generated GPE exhibited high electrochemical stability and the unit cell of LiFePO₄/GPE/Li could be cycled at room temperature.     

The effect of different lithium salts on conductivity of comb-like polymer electrolyte with chelating functional group

The behaviors of lithium ions in a comb-like polymer electrolyte with chelating functional group complexed with LiCF₃SO₃, LiBr and LiClO₄ were characterized by differential scanning calorimeter (DSC), thermogravimetric analysis (TGA), Fourier transform infrared (FT-IR) spectroscopy, AC impedance, and ¹³C solid-state NMR measurement. The comb-like copolymer was synthesized from poly(ethylene glycol) methyl ether methacrylate (PEGMEM) and (2-methylacrylic acid 3-(bis-carboxymethylamino)-2-hydroxy-propyl ester) (GMA-IDA). FT-IR spectra reveal the interactions of Li⁺ ions with both the ether oxygen of the PEGMEM and the nitrogen atom of the GMA-IDA segments. FT-IR spectra also indicate an increasing anion-cation association consistent with increasing LiCF₃SO₃ concentrations. Moreover, the ¹³C solid-state NMR spectra for the carbons attached to the ether oxygen atoms exhibited significant line broadening and a slight upfield chemical shift when the dopant was added to the polymer. These findings indicate coordination between the Li cation and the ether oxygens in the PEG segment. T_g and T_d of copolymers doped with salts clearly increase, as shown by DSC and TGA measurements. These results indicate the interactions of Li⁺ with both PEGMEM and GMA-IDA segments form transient cross-links inside the copolymers. The Vogel-Tamman-Fulcher (VTF)-like behavior of conductivity implies the coupling of the charge carriers with the segmental motion of the polymer chain in this study. The maximum conductivity of copolymers relates to the composition of the copolymers and the concentration of doping lithium ions. In summary, the GMA-IDA unit in the copolymer promotes the dissociation of the lithium salt, the mechanical strength and the conductivity of the polyelectrolyte.     

Complicated phase behavior and ionic conductivities of PVP-co-PMMA-based polymer electrolytes

We have used DSC, FTIR spectroscopy, and ac impedance techniques to investigate the interactions that occur within complexes of poly(vinylpyrrolidone-co-methyl methacrylate) (PVP-co-PMMA) and lithium perchlorate (LiClO₄) as well as these systems' phase behavior and ionic conductivities. The presence of MMA moieties in the PVP-co-PMMA random copolymer has an inert diluent effect that reduces the degree of self-association of the PVP molecules and causes a negative deviation in the glass transition temperature (T_g). In the binary LiClO₄/PVP blends, the presence of a small amount of LiClO₄ reduces the strong dipole-dipole interactions within PVP and leads to a lower T_g. Further addition of LiClO₄ increases T_g as a result of ion-dipole interactions between LiClO₄ and PVP. In LiClO₄/PVP-co-PMMA blend systems, for which the three individual systems—the PVP-co-PMMA copolymer and the LiClO₄/PVP and LiClO₄/PMMA blends—are miscible at all compositional ratios, a phase-separated loop exists at certain compositions due to a complicated series of interactions among the LiClO₄, PVP and PMMA units. The PMMA-rich component in the PVP-co-PMMA copolymer tends to be excluded, and this phenomenon results in phase separation. At a LiClO₄ content of 20 wt% salt, the maximum ionic conductivity occurred for a LiClO₄/VP57 blend (i.e., 57 mol% VP units in the PVP-co-PMMA copolymer).     

The environment of lithium ions and conductivity of comb-like polymer electrolyte with a chelating functional group

The behavior of lithium ions in a comb-like polymer electrolyte with a chelating functional group have been characterized by differential scanning calorimeter (DSC), dynamic mechanical analysis (DMA), Fourier transform infrared (FTIR) spectroscopy, ac impedance and ⁷Li solid-state NMR measurements. The comb-like copolymer is synthesized by poly(ethylene glycol-methyl ether methacrylate) (PEGMEM) and (2-methylacrylic acid 3-(bis-carboxymethylamino) -2-hydroxy-propyl ester) (GMA-IDA). FTIR and ⁷Li solid-state NMR spectra demonstrate the interactions of Li⁺ ions with both the ether oxygen of the PEGMEM and the nitrogen atom of the GMA-IDA segments. Moreover, ⁷Li solid-state NMR shows that the lithium ions are preferentially coordinated to the GMA-IDA segment. The T_g increases for the copolymers doped with LiClO₄. These results indicate the interactions of Li⁺ with both PEGMEM and GMA-IDA segments form transient cross-links. The Vogel-Tamman-Fulcher (VTF)-like behavior of conductivity implies the coupling of the charge carriers with the segmental motion of the polymer chains. The dependence of the maximum conductivity on the composition of the copolymers and the doping lithium ion concentration was determined. The GMA-IDA unit in the copolymer improves the dissociation of the lithium salt, the mechanical strength and the conductivity.     

Study of ionic conductivity and microstructure of a cross-linked polyurethane acrylate electrolyte

A cross-linked polyurethane acrylate (PUA) was synthesized by end capping 4,4′-methylene bis(cyclohexyl isocyanate), H₁₂MDI/poly-(ethylene glycol), PEG based prepolymer with hydroxy ethyl acrylate (HEA). Significant interactions of the Li⁺ ions with the soft and hard segments of the host polymer have been observed for the PUA complexed with lithium perchlorate (LiClO₄) by means of differential scanning calorimetry (DSC), Fourier transform infra-red (FTIR) spectroscopy, ⁷Li magic angle spinning (MAS) NMR measurements and thermogravimetric analysis (TGA). The ⁷Li MAS NMR investigation of the PUA indicates the presence of at least three distinct Li⁺ sites at lower temperature, which merge to a single one at higher temperature in similar line with uncross-linked polyurethane. The results of TGA, DSC and FTIR spectroscopy support the formation of different types of complexes by the interaction of the Li⁺ ions with different coordination sites of PUA. No detectable interactions could be observed between Li⁺ ions and groups in HEA. The DSC data indicates the formation of transient cross-links with the ether oxygens of the soft segment and mixing of soft and hard phases induced by the Li⁺ ions. In addition, a Vogel-Tamman-Fulcher (VTF) like temperature dependence of ionic conductivity implies coupling of the ion movement with the segmental motion of the polymer chains in the cross-linked environment. Predominant formation of contact ion pairs of LiClO₄ has been consistently observed through AC conductivity, DSC and NMR spectroscopic results. Swelling measurements of PUA with plasticizers reveal the improved dimensional stability for these cross-linked PUA in comparison with uncross-linked polyurethane.     

Study of polyurethane/sulfonated dimethyl fumarate complex

In this study linear polyether polyurethanes (PU) and sulfonated dimethyl fumarate (SDMF) were successfully synthesized and a series of novel solid polymer electrolytes, based on the complexes of PU and SDMF, were prepared. Fourier transform–Raman spectroscopy (FT‐Raman), ¹H‐NMR, differential scanning calorimetry (DSC), atomic force microscopy (AFM), and complex impedance analysis were utilized to investigate the chemical structure, microscale morphology, and ionic conductive property of this system. Results show that the ionic conductivity of the PU/SDMF series increases with increasing temperature. In the salt concentration range investigated, there is a maximum ionic conductivity for the PU/SDMF system. When the molar ratio of the ether oxygen and sodium cation is about 24, the optimum compatibility between the hard and soft segments is realized and the highest soft‐segment T_g is reached. A further increase in salt concentration causes the aggregation and precipitation of SDMF, and the decrease of the soft‐segment T_g. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 67–74, 2002; DOI 10.1002/app.10205     

The study on the conductivity of styrene-maleic anhydride copolymer electrolytes based on poly(ethylene glycol)400 and LiClO4

Polyelectrolytes, in this study were synthesized from styrene-maleic anhydride (SMA) copolymer, poly(ethylene glycol)400 (PEG400), and lithium perchlorate (LiClO₄). Fourier transform infrared spectroscopy (FTIR), and magic angle spinning (MAS) solid-state NMR were used to monitor the interaction between Li⁺ ions and polymer. The results of FTIR and MAS solid-state NMR indicate the Li⁺ ions are preferentially coordinated to the ether oxygen of PEG. The T_g of the PEG segments in polyelectrolyte increases with LiClO₄ concentration, as determined by differential scanning calorimetry (DSC), indicating that solubility of the Li⁺ ions in the host polymer increases with the PEG content. Impedance spectroscopy (IS) shows that the bulk conductivity of polyelectrolytes and the conductivity behavior obeys the Vogel-Tamman-Fulcher (VTF) equation.     

Blending poly(methyl methacrylate) and poly(styrene‐co‐acrylonitrile) as composite polymer electrolyte

A blend of poly(methyl methacrylate) (PMMA) and poly(styrene‐co‐acrylonitrile) (PSAN) has been evaluated as a composite polymer electrolyte by means of differential scanning calorimetry (DSC), Fourier transform infrared (FTIR) spectroscopy, ac impedance measurements, and linear sweep voltammetry (LSV). The blends show an interaction with the Li⁺ ions when complexed with lithium perchlorate (LiClO₄), which results in an increase in the glass‐transition temperature (T_g) of the blends. The purpose of using PSAN as another component of the blend is to improve the poor mechanical properties of PMMA‐based plasticized electrolytes. The mechanical property is further improved by introducing fumed silica as inert filler, and hence the liquid electrolyte uptake and ionic conductivity of the composite systems are increased. Room‐temperature conductivity of the order of 10^?4 S/cm has been achieved for one of the composite electrolytes made from a 1/1 blend of PSAN and PMMA containing 120% liquid electrolyte [1M LiClO₄/propylene carbonate (PC)] and 10% fumed silica. These systems also showed good compatibility with Li electrodes and sufficient electrochemical stability for safe operation in Li batteries. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 80: 1319–1328, 2001     

Tailor-made fumed silica-based nano-composite polymer electrolytes consisting of BmImTFSI ionic liquid

In this work, nano-sized fumed silica (SiO₂) was embedded in poly(methyl methacrylate) (PMMA)?Cpoly(vinyl chloride) (PVC) blend with 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl imide) (BmImTFSI) as ionic liquid. These composite polymer electrolytes (CPEs) were prepared by solution casting technique. The samples followed Arrhenius behavior in the temperature-dependence of ionic conductivity and further proved the ionic hopping mechanism in the polymer electrolyte. It is suggested the formation of three-dimensional polymer network among the aggregates weakens the interaction of polar group of the polymer backbone and initiates the ionic decoupling process. The mobile ions from adjacent sites would occupy this vacant site and reform the interactive bond with the polymer backbone whereby the ionic hopping mechanism is generated. The activation energy (E _a) is further determined. The higher the ionic conductivity, the lower the activation energy. The maximum ionic conductivity of (8.26?±?0.02) mScm^?1 was achieved at 80?°C upon inclusion of 8 wt% of SiO₂. X-ray diffraction (XRD) analysis revealed the higher amorphous region with increasing SiO₂ mass loadings. The coherence length is further determined by using Debye?CScherrer equation. Higher amorphous region in the polymer matrix is conferred by showing the lower coherent length. Scanning electron microscopy (SEM) was applied to examine the morphology of polymer electrolytes. Based on the differential scanning calorimetry (DSC) study, glass transition temperature (T _g) and melting temperature (T _m) were decreased. Highly flexible polymer chain is produced when the T _g was lowered down. On the other hand, thermal stability of polymer electrolytes was increased by SiO₂ dispersion, as depicted in thermogravimetric analysis (TGA).     

Preparation and performance analysis of barium titanate incorporated in corn starch‐based polymer electrolytes for electric double layer capacitor application

Polymer electrolyte membranes composing of corn starch as host polymer, lithium perchlorate (LiClO₄) as salt, and barium titanate (BaTiO₃) as composite filler are prepared using solution casting technique. Ionic conductivity is enhanced on addition of BaTiO₃ by reducing the crystallinity and increasing the amorphous phase content of the polymer electrolyte. The highest ionic conductivity of 1.28 × 10^?2 S cm^?1 is obtained for 10 wt % BaTiO₃ filler in corn starch‐LiClO₄ polymer electrolytes at 75°C. Glass transition temperature (T_g) of polymer electrolytes decreases as the amount of BaTiO₃ filler is increased, as observed in differential scanning calorimetry analysis. Scanning electron microscopy and thermogravimetric analysis are employed to characterize surface morphological and thermal properties of BaTiO₃‐based composite polymer electrolytes. The electrochemical properties of the electric double‐layer capacitor fabricating using the highest ionic conductivity polymer electrolytes is investigated using cyclic voltammetry and charge‐discharge analysis. The discharge capacitance obtained is 16.22 F g^?1. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43275.     

LiClO4 doped cellulose acetate as biodegradable polymer electrolyte for supercapacitors

The possibility of producing a biodegradable polymer electrolyte based on cellulose acetate (CA) with varied concentration of LiClO₄ for use in supercapacitors has been investigated. The successful doping of the CA films has been analyzed by FTIR and DSC measurements of the LiClO₄ doped CA films. The ionic conductivity of the films increased with increase in salt content and the maximum ionic conductivity obtained for the solid polymer electrolyte at room temperature was 4.9 × 10^?3 Ω^?1 for CA with 16% LiClO₄. The biodegradation of the solid polymer electrolyte films have been tested by soil burial, degradation in activated sludge, and degradation in buffer medium methods. The extent of biodegradation in the films has been measured by AC Impedance spectroscopy and weight loss calculations. The study indicated sufficient biodegradability of the materials. A p/p polypyrrole supercapacitor has been fabricated and its electrochemical characteristics and performance have been studied. The supercapacitor showed a fairly good specific capacitance of 90 F g^?1 and a time constant of 1 s. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Characteristics of PPG-based thermoplastic polyurethane doped with lithium perchlorate

Segmented thermoplastic polyurethane (TPU) was synthesized from methylene bis(cyclohexyl isocyanate) (H₁₂MDI), ethylenediamine (EDA), and poly(propylene glycol) (PPG) with a molecular weight of 1000. The ratio of hard segment to soft segment (NCO/OH) is changed to test the chemical and physical properties. Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), and impedance spectroscopy (IS) were utilized to monitor the phase change of these TPU samples with various lithium perchlorate (LiClO₄) concentrations. Significant changes occur in the FTIR spectrum of the TPU with LiClO₄ concentration above 0.5 mmol/g TPU, indicating that an interaction existed between the lithium cation and the hard segment or soft phase. The soft-segment T_g increased with increasing LiClO₄ concentration through the examination of DSC. IS results indicate an increase in bulk conductivity as the salt concentration is increased. Electrochemical stability of the TPU sample was studied by cyclic votammetry (CV). © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 82: 389–399, 2001