Influence of oxygen plasma treatment parameters on the properties of carbon fiber

This study is focused on the impact of oxygen plasma treatment on properties of carbon fibers and interfacial adhesion behavior between the carbon fibers and epoxy resin. The influences of the main parameters of plasma treatment process, including duration, power, and flow rate of oxygen gas were studied in detail using interlaminar shear strength (ILSS) of carbon fiber composites. The ILSS of composites made of carbon fibers treated by oxygen plasma for 1 min, at power of 125 W, and oxygen flow rate of 100 sccm presented a maximum increase of 28% compared to composites made of untreated carbon fibers. Furthermore, carbon fibers were characterized by scanning electron microscopy (SEM), tensile strength test, attenuated total reflectance Fourier transform infrared (ATR-FTIR), and Raman spectroscopy analyses. It was found that the concentration of reactive functional groups on the fiber surface was increased after the plasma modification, as well the surface roughness, which finally improved the interfacial adhesion between carbon fibers and epoxy resin. However, high power and long exposure times could partly damage the surface of carbon fibers and decrease the tensile strength of filaments and ILSS of treated fiber composites.     

Recycling carbon fiber from composite waste and its reinforcing effect on polyvinylidene fluoride composite: Mechanical,morphology, and interface properties

Recycled carbon fiber (RCF) was reclaimed from thermoset composite waste and employed as reinforcement from 0 to 30 wt% to prepare polyvinylidene fluoride (PVDF)/RCF composite. Commercial virgin carbon fiber (VCF) was used as comparison. The surface morphology, chemistry, and tensile properties of carbon fibers were investigated by Scanning Electron Microscopy (SEM), X‐Ray Photoelectron Spectroscopy (XPS), and tensile test. Results showed that the roughness, O/C ratio and –COO content of RCF surface were significantly improved after recycling. In addition, the single fiber tensile strength and modulus of RCF was lower than that of VCF. The interfacial adhesion between RCF and PVDF was much stronger due to the high chemical activity and roughness over the RCF surface. Mechanical properties of composites were investigated by flexural test, impact test, and Dynamic Mechanical Analysis (DMA). It is found that the PVDF/RCF composite showed higher flexural properties, storage modulus, and lower impact strength, which indicated the strong interfacial adhesion, played an important role in reinforcing. The morphology of fracture further demonstrated the strong interface in PVDF/RCF composite. The fiber length distribution and crystallinity of composites were also evaluated to characterize the composites. The work develops potential for recycling and reuse of carbon fiber, and also expands the application of PVDF based composite. POLYM. COMPOS., 38:2544–2552, 2017. © 2015 Society of Plastics Engineers     

Effect of the atmospheric plasma treatment parameters on jute fabric: The effect on mechanical properties of jute fabric/polyester composites

The effect of atmospheric air plasma treatment of jute fabrics on the mechanical properties of jute fabric reinforced polyester composites was investigated. The jute fabrics were subjected to different plasma powers (60, 90, and 120 W) for the exposure times of 1, 3, and 6 min. The effects of plasma powers and exposure times on interlaminar shear strength, tensile strength, and flexural strength of polyester based composites were evaluated. The greatest ILSS increase was about 171% at plasma power of 120 W and exposure time of 6 min. It is inferred that atmospheric air plasma treatment improves the interfacial adhesion between the jute fiber and polyester. This result was also confirmed by scanning electron microscopy observations of the fractured surfaces of the composites. The greatest tensile strength and flexural strength values were determined at 120 W for 1 min and at 60 W for 3 min, respectively. Moreover, it can be said that atmospheric air plasma treatment of jute fibers at longer exposure times (6 min) made a detrimental effect on tensile and flexural properties of jute‐reinforced polyester composites. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Recycling carbon fiber composites using microwave irradiation: Reinforcement study of the recycled fiber in new composites

With increasing use of carbon fiber reinforced polymer (CFRP) composites in transportation, sports, and many other industries, recycling of the scrap and end‐of‐life composites has presented both great challenges and opportunities. In this work, we report our study on reclaiming carbon fibers from CFRP using energy efficient microwave irradiation. Different irradiation conditions were used and the optimal conditions were determined based on the surface morphology of the recycled fiber. Polypropylene (PP) and Nylon, representing nonpolar and polar polymers, respectively, were reinforced using the recycled fiber through extrusion and injection molding. For comparison, PP and Nylon reinforced by virgin carbon fiber were also prepared using the same processing conditions. Tensile, flexural, and impact test results showed that, while both carbon fibers could improve these properties, they exhibited different reinforcing effects on the two polymers. The recycled fiber outperformed the virgin fiber in reinforcing PP whereas the virgin fiber performed better in Nylon. This was due to the differences in surface roughness, surface bonding, and fiber aspect ratio between the two fibers. This study shows the great potential of recycled carbon fiber and microwave irradiation as an effective recycling technique. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42658.     

Effect of plasma modification on the mechanical properties of carbon fiber/phenolphthalein polyaryletherketone composites

A study was carried out to investigate the effect of plasma modification on the mechanical properties of carbon fiber/phenolphthalein polyaryletherketone composites. The influence of oxygen plasma treatment on the surface properties of carbon fibers was investigated by X‐ray photoelectron spectroscopy and atomic force microscopy. The results indicated that oxygen plasma treatment was capable of increasing the concentrations of the oxygen‐containing groups of the carbon fiber surface as well as enhancing surface roughness. Both the chemical bonding and mechanical interlocking gave rise to an increase of the interlaminar shear strength of composite. Scanning electron microscope photographs showed that the destruction mode of composites was changed after the carbon fibers were treated by oxygen plasma. The results also indicated that the flexural properties of plasma‐treated carbon fiber composites were improved. POLYM. COMPOS., 2013. © 2013 Society of Plastics Engineers     

A new strategy for high-value reutilization of recycled carbon fiber: Preparation and friction performance of recycled carbon fiber felt-based C/C-SiC brake pads

To achieve the high-value reutilization of recycled carbon fiber (rCF), a new strategy of preparing rCF-based C/C-SiC brake pads is proposed in this work. The results show that the rCF possesses crystal structure and tensile strength comparable with those of virgin CF (vCF) exception of pyrolytic char adhering to the surface of rCF after pyrolysis. The rCF was converted into C/C composites through impregnation-pyrolysis. Pyrolytic char was found to have no evident negative effect on the densification rates of the rCF C/C composites. By reactive melt infiltration, the rCF C/C-SiC composites were fabricated based upon the rCF C/C composites. The achieved rCF C/C-SiC composites do not differ markedly from the vCF group control in terms of microstructure and bending strength. Furthermore, the thermal diffusion coefficients of the rCF C/C-SiC composites are very close to those of vCF C/C-SiC composites in the temperature range 25°C-300 °C. The coefficient of friction values of the rCF C/C-SiC composites are as stable as those of vCF control group, both being maintained at approximately 0.4 during friction test, whether at 25 °C or 300 °C. The wear rate of the rCF C/C-SiC composites is 3.8 μm·min⁻¹, nearly indistinguishable from that of the vCF C/C-SiC composites, i.e., 4.5 μm·min⁻¹, further suggesting that the two materials resemble each other closely. The rCF C/C-SiC composites exhibit great potential for use as alternative brake pads to serve auto braking systems. This work opens up a new path for high-value reuse of rCF.     

Hybrid effect on mechanical properties of M40‐T300 carbon fiber reinforced Bisphenol A Dicyanate ester composites

Interply and intraply hybrid composites based on Bisphenol A Dicyanate ester (BADCy), high strength carbon fibers T300, and high modulus carbon fibers M40 were prepared by monofilament dip‐winding and press molding technique. The tensile, flexural, interlaminar shear properties and SEM analysis of the hybrid composites with different fiber content and fiber arrangement were investigated. The results indicated that the mechanical properties of intraply hybrid composites were mainly determined by fiber volume contents. When the ratio of fiber volume content was close to 1:1, the intraply hybrid composites possessed lowest tensile and flexural strength. The mechanical properties of interply hybrid composite mainly depended on the fiber arrangement, instead of the fiber volume contents. The hybrid composites using T300 fiber layout as outside layer possessed high flexural strength and low flexural modulus, which was close to that of T300/BADCy composites. The hybrid composites ([(M40)_x/(T300)_y]_S) using M40 fiber layout as outside layer and T300 fibers in the mid‐plane had high flexural modulus and interlaminar shear strength. POLYM. COMPOS., 2010. © 2010 Society of Plastics Engineers     

Mechanical properties of composites from sawdust and recycled plastics

Mechanical properties of wood plastic composites (WPCs) manufactured from sawdust and virgin and/or recycled plastics, namely high density polyethylene (HDPE) and polypropylene (PP), were studied. Sawdust was prepared from beech industrial sawdust by screening to the desired particle size and was mixed with different virgin or recycled plastics at 50% by weight fiber loading. The mixed materials were then compression molded into panels. Flexural and tensile properties and impact strength of the manufactured WPCs were determined according to the relevant standard specifications. Although composites containing PP (virgin and recycled) exhibited higher stiffness and strength than those made from HDPE (virgin and recycled), they had lower unnotched impact strengths. Mechanical properties of specimens containing recycled plastics (HDPE and PP) were statistically similar and comparable to those of composites made from virgin plastics. This was considered as a possibility to expand the use of recycled plastics in the manufacture of WPCs. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 3641–3645, 2006     

Microstructural,mechanical, and thermal characteristics of recycled cellulose fiber‐halloysite‐epoxy hybrid nanocomposites

Epoxy hybrid‐nanocomposites reinforced with recycled cellulose fibers (RCF) and halloysite nanotubes (HNTs) have been fabricated and investigated. The dispersion of HNTs was studied by synchrotron radiation diffraction (SRD) and transmission electron microscopy (TEM). The influences of RCF/HNTs dispersion on the mechanical properties and thermal properties of these composites have been characterized in terms of flexural strength, flexural modulus, fracture toughness, impact toughness, impact strength, and thermogravimetric analysis. The fracture surface morphology and toughness mechanisms were investigated by SEM. Results indicated that mechanical properties increased because of the addition of HNTs into the epoxy matrix. Flexural strength, flexural modulus, fracture toughness, and impact toughness increased by 20.8, 72.8, 56.5, and 25.0%, respectively, at 1 wt% HNTs load. The presence of RCF dramatically enhanced flexural strength, fracture toughness, impact strength, and impact toughness of the composites by 160%, 350%, 444%, and 263%, respectively. However, adding HNTs to RCF/epoxy showed only slight enhancements in flexural strength and fracture toughness. The inclusion of 5 wt% HNTs into RCF/epoxy ecocomposites increased the impact toughness by 27.6%. The presence of either HNTs or RCF accelerated the thermal degradation of neat epoxy. However, at high temperature, samples reinforced with RCF and HNTs displayed better thermal stability with increased char residue than neat resin. POLYM. COMPOS. 2012. © 2012 Society of Plastics Engineers     

Mechanical and thermal properties of polypropylene/recycled polyethylene terephthalate/chopped rice husk composites

The various ratios of recycled polyethylene terephthalate (rPET) into polypropylene (PP) filled with 40 parts chopped rice husk per hundred part of polymer have been studied. Composites were prepared using a corotating twin screw extruder at temperature zones of 165–215, well below 250°C (rPET mp temperature) and characterized by mechanical and thermal properties. To improve the compatibility between different components, PP grafted with maleic anhydride was added as a coupling agent in all the compositions studied. The results showed that the addition of rPET improved the tensile and flexural modulus and impact strength of the composite while reducing its tensile and flexural strength. The scanning electron microscopy micrographs of samples in the injection direction showed that some particle shaped rPET inside the composites appear as drawn fibrils and some appear as plates. Differential scanning calorimetric studies showed that the addition of rPET particles to the composites decrease the PP crystallization temperatures. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Morphological,mechanical, and physical properties of composites made with wood flour‐reinforced polypropylene/recycled poly(ethylene terephthalate) blends

Wood flour (WF)‐filled composites based on a polypropylene (PP)/recycled polyethylene terephthalate (r‐PET) matrix were prepared using two‐step extrusion. Maleic anhydride grafted polypropylene (MAPP) was added to improve the compatibility between polymer matrices and WF. The effects of filler and MAPP compatibilization on the water absorption, mechanical properties, and morphological features of PP/r‐PET/WF composites were investigated. The addition of MAPP significantly improved mechanical properties such as tensile strength, flexural strength, tensile modulus, and flexural modulus compared with uncompatibilized composites, but decreased elongation at break. Scanning electron microscopic images of fracture surface specimens revealed better interfacial interaction between WF and polymer matrix for MAPP‐compatibilized PP/r‐PET/WF composites. MAPP‐compatibilized PP/r‐PET/WF composites also showed reduced water absorption due to improved interfacial bonding, which limited the amount of absorbable water molecules. These results indicated that MAPP acts as an effective compatibilizer in PP/r‐PET/WF composites. POLYM. COMPOS., 38:1749–1755, 2017. © 2015 Society of Plastics Engineers     

Mechanical and open hole tensile properties of self‐reinforced PET composites with recycled PET fiber reinforcement

The tensile strength of notched composites is an important factor for composite structural design. However, no literature is available on the notch sensitivity of self‐reinforced polymer composites. In this study, self‐reinforced recycled poly (ethylene terephthalate) (srrPET) composites were produced by film stacking from fabrics composed of double covered uncommingled yarns (DCUY). Composite specimens were subjected to uniaxial tensile, flexural, and Izod impact tests and the related results compared with earlier ones achieved on srPET composites reinforced with nonrecycled technical PET fibers. Effects of open circular holes on the tensile strength of srrPETs were studied at various width‐to‐hole diameter (W/D) ratios of the specimens. In the open hole tensile (OHT) measurements bilinear (yielding followed by post‐yield hardening) stress–strain curves were recorded. The srrPET composites had extremely high yield strength retention (up to 142%) and high breaking strength retention (up to 81%) due to the superior ductile nature of the srrPETs, which induces plastic yielding near the hole thereby reducing the stress concentration effect. The results proved that srrPET composites are tough, ductile notch‐insensitive materials. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2016 , 133, 43682.     

Effect of hybridization and compatibilization on the mechanical properties of recycled polypropylene‐hemp composites

Hemp fibers and particles, with different sizes and contents, were used to make hybrid composites based on recycled polypropylene (PP). In particular, the effect of maleated polypropylene (MAPP) addition on the morphology and mechanical properties is reported. The results show that better adhesion is obtained with MAPP addition. In general, fiber content and size had a substantial effect on the tensile, flexural, torsion, and impact properties of the resulting composites. Although, adding MAPP to the samples improved the impact strength of the composites, the values were always lower than neat PP. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Plasma etching and plasma polymerization coating of carbon fibers. Part 1. Interfacial adhesion study

Unsized AS-4 carbon fibers were etched by RF plasma and then coated via plasma polymerization in order to enhance their adhesion to vinyl ester resin. Gases utilized for plasma etching were Ar, N₂ and O₂, while monomers used in plasma polymerization coating were acetylene, butadiene and acrylonitrile. Plasma etchings were carried out as a function of plasma power (30–70 W), treatment time (1–10 min) and gas pressure (20–40 mtorr). Plasma polymerizations were performed by varying the treatment time (15–60 s), plasma power (10–30 W) and gas pressure (20-40 mtorr). The conditions for plasma etching and plasma polymerization were optimized by measuring interfacial adhesion with vinyl ester resin via micro-droplet tests. Plasma etched and plasma polymer coated carbon fibers were characterized by SEM, XPS, FT-IR and α-Step, dynamic contact angle analyzer (DCA) and tensile strength measurements. In Part 1, interfacial adhesion of plasma etched and plasma polymer coated carbon fibers to vinyl ester resin is reported, while characterization results including tensile strength of carbon fibers are reported in Part 2. Among the treatment conditions, a combination of Ar plasma etching and acetylene plasma polymer coating provided greatly improved interfacial shear strength (IFSS) of 69 MPa, compared to 43 MPa obtained from as-received carbon fiber. Based on the SEM analysis of failure surfaces and load-displacement curves, the failure was found to occur at the interface between plasma polymer coating and vinyl ester resin.     

Influence of plasma treatment on properties of ramie fiber and the reinforced composites

In this research, 9 series of ramie fibers were treated under low-temperature plasma with diverse output powers and treatment times. By analysis of the surface energy and adhesion power with epoxy resin, 3 groups as well as control group were chosen as reinforced fibers of composites. The influences of these parameters on the ramie fiber and its composites such as topography and mechanical properties were tested by scanning electron microscopy (SEM), atomic force microscopy (AFM), tensile property and fragmentation test of single-fiber composites. Contact angle and surface free energy results indicated that with the increased treatment times and output powers, surface energy and adhesion work with epoxy resin improved. Compared with the untreated fibers, surface energy and adhesion work with epoxy resin grew 124.5 and 59.1% after 3 min-200 w treatment. SEM and AFM showed low temperature plasma treatment etched the surface of ramie fiber to enhance the coherence between fiber and resin, consequently fiber was not easy to pull-out. After 3 min-200 w treatment, tensile strength of ramie fiber was 253.8 MPa, it had about 30.5% more than that of untreated fiber reinforced composite. Interface shear stress was complicated which was affected by properties of fiber, resin and interface. Fragmentation test showed biggest interface shear stress achieved 17.2 MPa, which represented a 54.0% increase over untreated fiber reinforced composites.     

The effect of atmospheric‐pressure air plasma discharge power on adhesive properties of aramid fibers

After exposure to the atmospheric‐pressure air plasma at different discharge powers, the adhesion characteristics of Twaron aramid fibers were investigated. For the 12 s‐300 W plasma treatment, the interlaminar shear strength of Twaron fiber reinforced thermoplastic poly(phthalazinone ether sulfone ketone) was increased from 46.0 to 61.7 MPa by 34.1%, and the diffusion of water molecule into the resulting composites was proved to be effectively prevented. These results showed that surface adhesive properties of the plasma‐treated aramid fibers were improved. At the power level of 300 W, X‐ray photoelectron spectroscopy analysis revealed the increases in concentrations of oxygen and nitrogen polar groups on the fiber surface, and atomic force microscopy observations led to the conclusion that the fiber surface morphology was changed and the surface roughness was greatly increased. These new polar and irregular surface structures accounted for the better adhesion between the fiber and the matrix, while due to the reasonability of this discharge power level applied to the surface modification, the measured fiber tensile strength only decreased by 2.0%. POLYM. COMPOS., 37:620–626, 2016. © 2014 Society of Plastics Engineers     

回收聚丙烯/废书刊纸纤维复合材料结构与力学性能的研究

以废书刊纸纤维(OMGF)和回收聚丙烯(PP)为原料,马来酸酐接枝聚丙烯(MAPP)为相容剂,采用热压成型法制备了PP/OMGF木塑复合材料。研究了OMGF含量对复合材料拉伸性能及弯曲性能的影响,并采用红外光谱和扫描电子显微镜分析了OMGF的结构及复合材料的拉伸断面形貌。结果表明,OMGF对PP基体具有一定的增强作用,当OMGF含量为30%时,复合材料的拉伸强度和弯曲强度分别达到最大值29.53MPa和33.67MPa,比回收PP分别提高了51.6%和31.7%;随着OMGF含量的增加,复合材料的断裂伸长率逐渐下降,弯曲模量逐渐上升。扫描电子显微镜分析显示,当OMGF含量较低时,其与PP基体之间具有良好的界面相容性;当OMGF含量增加到50%时,界面相容性明显下降。     

废旧聚丙烯/废弃印刷线路板非金属粉复合材料的制备及性能

采用挤出注塑法以废旧聚丙烯（WPP）为基体、废弃线路板非金属粉（WPCBN）为填料制备了复合材料。考察了WPCBN对材料阻燃性能及力学性能的影响。通过红外光谱和扫描电子显微镜分析研究了WPCBN改性前后官能团结构及复合材料冲击断面形貌的差异,以探讨硅烷偶联剂（KH550）、马来酸酐接枝聚丙烯（MAPP）对WPP/WPCBN界面相容性改善及复合材料力学性能提高的作用机理。结果表明,WPCBN超过10 phr后复合材料具有自熄性;经1.5 phr KH550改性后,WPCBN与WPP间的界面黏结力增强,复合材料拉伸、弯曲及冲击强度分别提高6.5%、6.25%和17.9%;m（WPP）：m（WPCBN）：m（MAPP）为100：30：9时,复合材料的拉伸、弯曲强度增幅最大,分别为37.5%和48.8%;WPP/WPCBN与新聚丙烯（NPP）/WPCBN复合材料相比,拉伸、弯曲强度仅降低16.8%、20.4%。     

The effect of alkali treatment and filler size on the properties of sawdust/UPR composites based on recycled PET wastes

In this study, natural sawdust fillers from acacia were mixed with unsaturated polyester resin (UPR), which was prepared by recycling of polyethylene terephthalate (PET) waste bottles to prepare sawdust/UPR composite. PET wastes were recycled through glycolysis and depolymerized to produce a formulation for the resin. The effects of alkali treatment, filler content, and filler size on the tensile, flexural, hardness, and water absorption of the composites were investigated. The results show that the modulus of both tensile and flexural increased with increasing filler contents, but the tensile and flexural strength of composites decreased. The size of sawdust also played a significant role in the mechanical properties, with smaller size sawdust producing higher strength and modulus. This is due to the greater surface area for filler–matrix interaction. The results also show that alkali treatment causes a better adhesion between sawdust and UPR matrix and improves the mechanical properties of the composites. Furthermore, surface treatment reduced the water absorption of composites. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Mechanical properties of carbon fiber reinforced bisphenol A dicyanate ester composites modified with multiwalled carbon nanotubes

A novel electrophoretic deposition (EPD) method was employed for grafting multiwalled carbon nanotubes (MWCNTs) on carbon fibers, which, after impregnation with bisphenol A dicyanate ester (BADCy), synergistically reinforced BADCy matrix composites (CNT‐C/BADCy). The effect of MWCNT presence on the mechanical properties of the composites was investigated. Composite tensile strength increased by 45.2% for an EPD duration of 2 min, while flexural strength exhibited a decreasing trend with EPD duration. Optical microscopy revealed that the existence of MWCNTs enhanced the fiber‐matrix interface while a large number of CNTs were observed to have pulled‐out from the matrix, a finding which explained the observed tensile strength increase in terms of energy dissipation by the specific toughening mechanism. The flexural strength decrease of the composites with CNTs as compared to specimens without nanotubes was found linked to the increased stress concentration in the BADCy matrix due to tube presence which weakens the adhesion between carbon fabrics. In a word, carbon nanotubes will enhance the micro interface and weaken the macro interface of the composites. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 45100.