An optimization and modeling approach for H2O2/UV‐C oxidation of a commercial non‐ionic textile surfactant using central composite design

BACKGROUND: Industrial surfactants are biologically complex organics that are difficult to degrade and may cause ecotoxicological risks in the environment. Until now, many scientific reports have been devoted to the effective treatment of surfactants employing advanced oxidation processes, but there is no available experimental study dealing with the optimization and statistical design of surfactant oxidation with the well‐established H₂O₂/UV‐C process. RESULTS: Considering the major factors influencing H₂O₂/UV‐C performance as well as their interactions, the reaction conditions required for the complete oxidation of a commercial non‐ionic textile surfactant, an alkyl ethoxylate, were modeled and optimized using central composite design‐response surface methodology (CCD‐RSM). Experimental results revealed that for an aqueous non‐ionic surfactant solution at an initial chemical oxygen demand (COD) of 450 mg L^?1, the most appropriate H₂O₂/UV‐C treatment conditions to achieve full mineralization at an initial pH of 10.5 were 47 mmol L^?1 H₂O₂ and a reaction time of 86 min (corresponding to a UV dose of 30 kWh m^?3). CONCLUSION: CCD allowed the development of empirical polynomial equations (quadratic models) that successfully predicted COD and TOC removal efficiencies under all experimental conditions employed in the present work. The process variable treatment time, followed by the initial COD content of the aqueous surfactant solution were found to be the main parameters affecting treatment performance, whereas the initial H₂O₂ concentration had the least influence on advanced oxidation efficiencies. The H₂O₂ concentration and surfactant COD were found to be more important for TOC abatement compared with COD abatement. Copyright © 2009 Society of Chemical Industry     

Degradation of Sulfosalicylic Acid by O3/UV O3/TiO2/UV,and O3/V-O/TiO2 : A Comparative Study

Chemical oxygen demand (COD) removal rates of sulfosalicylic acid (SSal) degraded by three advanced oxidation processes (AOPs): O₃/UV, O₃/TiO₂/UV and O₃/V-O/TiO₂ are compared in this paper. (V = Vanadium). The results show that O₃/V-O/TiO₂ is the most effective process among three AOPs and the order of degradation efficiencies at different pH values is shown as O₃/V-O/TiO₂ > O₃/TiO₂/UV > O₃/UV. For example, at the buffered solution of pH 6.8, the COD removal rate of O₃/V-O/TiO₂ reaches 70% in 30 minutes, but those of O₃/TiO₂/UV and O₃/UV are 55% and 47% at the same conditions, respectively. Furthermore, the effect of CO₃ ^{2 ?}on the COD removal rates of three AOPs shows that O₃/V-O/TiO₂ and O₃/TiO₂/UV may be considerable promising methods to overcome the limitation of the presence of radical scavenger in solution. Both the adsorption of SSal on catalysts and other oxidants (atom oxygen, photo-generated hole) must be responsible for the above result.     

Mineralization of bisphenol A by advanced oxidation processes

BACKGROUND: Endocrine disruptors, as in the case of bisphenol A (BPA), are increasingly found in aqueous effluents. The degree of mineralization of a bisphenol A (BPA) aqueous solution after applying several oxidation treatments has been investigated. RESULTS: UV‐C photolysis of BPA allowed calculation of the quantum yield, ϕ_λ=254 = 0.045 ± 0.005 mol Einstein⁻¹ but only 15% of the initial organic carbon content (TOC) was eliminated. Better results (80% conversion) were obtained after TiO₂ addition. Ozone inmediately reacts with BPA. Again, TiO₂ addition in the presence of O₃ was capable of increasing the mineralization level (60%). The photolytic ozonation of BPA was capable of completely eliminating TOC. The presence of activated carbon in the O₃/UV and O₃/UV/TiO₂ systems significantly enhanced the TOC removal reaction rate (100% conversion in 20 min). CONCLUSIONS: Processes such as ozonation or photolysis are capable of efficiently removing BPA from water however, mineralization levels are rather low. Addition of TiO₂ to O₃ or UV‐C significantly enhances TOC removal. The remaining organics still account for an average 20–40% of the initial organic carbon. The combination of O₃/UV‐C is capable of completely mineralizing BPA. Activated carbon and/or TiO₂ addition to the system O₃/UV‐C improves the TOC depletion rate. Copyright © 2008 Society of Chemical Industry     

Biological treatment of saline wastewaters from marine‐products processing factories by a fixed‐bed reactor

Wastewaters generated by a factory processing marine products are characterized by high concentrations of organic compounds and salt constituents (>30 g dm^?3). Biological treatment of these saline wastewaters in conventional systems usually results in low chemical oxygen demand (COD) removal efficiency, because of the plasmolysis of the organisms. In order to overcome this problem a specific flora was adapted to the wastewater from the fish‐processing industry by a gradual increase in salt concentrations. Biological treatment of this effluent was then studied in a continuous fixed biofilm reactor. Experiments were conducted at different organic loading rates (OLR), varying from 250 to 1000 mg COD dm^?3 day^?1. Under low OLR (250 mg COD dm^?3 day^?1), COD and total organic carbon (TOC) removal efficiencies were 92.5 and 95.4%, respectively. Thereafter, fluctuations in COD and TOC were observed during the experiment, provoked by the progressive increase of OLR and the nature of the wastewater introduced. High COD (87%) and TOC (99%) removal efficiencies were obtained at 1000 mg COD dm^?3 day^?1. © 2002 Society of Chemical Industry     

Double‐functional characteristics of a surface molecular imprinted adsorbent with immobilization of nano‐TiO2

A new chitosan molecular imprinted adsorbent obtained by immobilization of nano‐TiO₂ on the adsorbent surface (surface‐imprinted adsorbent with nano‐TiO₂) was prepared. Based on photocatalytic reaction and the surface molecular imprinting technology, this new kind of surface‐imprinted adsorbent with immobilization of nano‐TiO₂ can not only adsorb template metal ions but can also degrade organic pollutants. The results showed that, after the nano‐TiO₂ was immobilized on the adsorbent surface, the adsorption ability for the imprinted ion (Ni²⁺) of this new imprinted adsorbent immobilized with nano‐TiO₂ was not affected, but the degradation ability for p‐nitrophenol (PNP) of the surface‐imprinted adsorbent with nano‐TiO₂ increased three‐fold compared with that of the surface‐imprinted adsorbent without nano‐TiO₂, from 23.8 to 76.1% (at an initial PNP concentration of 20 mg·dm^?3). The optimal TiO₂ concentration in the adsorbent preparation was 0.025 g·TiO₂ g^?1 adsorbent. The removal capacity for PNP reached 60.25 mg·g^?1 (at 400 mg·dm^?3 initial PNP concentration) under UV irradiation. The surface‐imprinted adsorbent with nano‐TiO₂ can be reused for at least five cycles without decreasing the removal ability for PNP and the imprinted ion (Ni²⁺). Copyright © 2006 Society of Chemical Industry     

Enhanced biodegradation of 2‐chloronitro‐benzene using a coupled zero‐valent iron column and sequencing batch reactor system

BACKGROUND: This study focused on the effectiveness of the zero‐valent iron (ZVI) pre‐treatment for enhancing the biodegradability of 2‐chloronitrobenzene (2‐ClNB), and further to evaluate the performance and mechanism of a coupled ZVI column–sequencing batch reactor (SBR) system treating 2‐ClNB contained wastewater. RESULTS: 2‐ClNB was readily transformed into 2‐chloroaniline (2‐ClAn) with the efficiency over 99.9% by ZVI column, and its biodegradability was significantly enhanced via ZVI pretreatment. The transformed effluent was subsequently fed into the SBR followed by 2‐ClAn loading of 3.4–117.2 g m^?3 d^?1 and COD loading around 1000 g m^?3 d^?1. A 2‐ClAn removal efficiency over 99.9% and COD removal efficiency of 82.0–98.1% were obtained. Moreover, 91.9 ± 0.1% TOC removal efficiency and 107.1 ± 6.0% chloride recovery efficiency during one cycle confirmed the complete biodegradation of 2‐ClAn in the coupled system. 16S rDNA PCR‐DGGE analysis suggested that ZVI pretreatment enhanced the diversity of the microbial community and promoted enrichment of the functional microorganisms degrading 2‐ClAn in the following SBR. CONCLUSION: ZVI pretreatment significantly enhanced the biodegradability of 2‐ClNB, and the coupled ZVI–SBR system demonstrated excellent performance when treating wastewater containing 2‐ClNB. Copyright © 2011 Society of Chemical Industry     

Slaughterhouse wastewater treatment by combined anaerobic baffled reactor and UV/H2O2 processes

Combined processes of biological anaerobic baffled reactor (ABR) and UV/H₂O₂ at a laboratory scale were studied to treat a synthetic slaughterhouse wastewater. In this study, the total organic carbon (TOC) loadings of 0.2-1.1 g/(L day) were used. The results revealed that combined processes had a higher efficiency to treat the synthetic slaughterhouse wastewater. Up to 95% TOC removal was obtained for an influent concentration of 973.3 mgTOC/L at the hydraulic retention time (HRT) of 3.8 days in the ABR and 3.6 h in the UV photoreactor. Meanwhile, up to 97.7% and 96.6% removal of chemical oxygen demand (COD) and 5-day carbonaceous biochemical oxygen demand (CBOD₅) were observed in the ABR for the same influent concentration, respectively. Comparatively, for an influent concentration of 157.6 mgTOC/L, the UV/H₂O₂ process alone with the TOC loading of 0.06-1.9 g/(L h) was also studied, in which, up to 64.3%, 83.7%, and 84.3% of TOC, COD, and CBOD₅ removal were observed, respectively, at the HRT of 2.5 h with hydrogen peroxide (H₂O₂) concentration of 529 mg/L. It was found that individual ABR and UV/H₂O₂ processes enhanced the biodegradability of the treated effluent by an increased CBOD₅/COD ratio of 0.4 to 0.6. An optimum H₂O₂ dosage of 3.5 (mgH₂O₂)/(mgTOC_in h) was also found for the UV/H₂O₂ process.     

Optimization of sulfamethoxazole degradation by TiO2/hydroxyapatite composite under ultraviolet irradiation using response surface methodology

A titanium dioxide/hydroxyapatite/ultraviolet (TiO₂/HAP/UV-A) system was used to remove sulfamethoxazole (SMX) from water in a second-order response surface methodology (RSM) experiment with a three-level Box-Behnken design (BBD) for optimization. The effects of both the primary and secondary interaction effects of three photocatalytic reaction variables were examined: the concentration of SMX (X₁), dose of TiO₂/HAP composite (X₂), and UV intensity (X₃). The UV intensity and TiO₂/HAP dose significantly influence the SMX and total organic carbon (TOC) removal (p<0.001). However, the SMX and TOC removal are enhanced with increasing TiO₂/HAP dose up to certain levels, and further increases in the TiO₂/HAP dose result in adverse effects due to hydroxyl radical scavenging at higher catalyst concentrations. Complete removal of SMX was achieved upon UV-A irradiation for 180min. Under optimal conditions, 51.2% of the TOC was removed, indicating the formation of intermediate products during SMX degradation. The optimal ratio of SMX (mg L^?1) to TiO₂/HAP (g L^?1) to UV (W/L) was 5.4145 mg L^?1 to 1.4351 g L^?1 to 18W for both SMX and TOC removal. By comparison with actual applications, the experimental results were found to be in good agreement with the model’s predictions, with mean results for SMX and TOC removal of 99.89% and 51.01%, respectively.     

Chemical treatment of cork‐processing wastewaters for potential reuse

The chemical treatment of cork‐processing wastewater by ozonation, alone and in combination with hydrogen peroxide and UV radiation was investigated. A reduction of the chemical oxygen demand (COD) ranging from 42% to 76% was obtained during ozonation after 3 h of reaction, depending on the experimental conditions. The additional presence of hydrogen peroxide and UV radiation enhanced the efficiency of the ozonation treatment due to the contribution of the OH radicals formed in the decomposition of ozone. Thus, final reductions of the COD higher than 90% and a complete elimination of phenolic compounds and absorbance at 254 nm were achieved in both Advanced Oxidation Processes (AOPs), O₃/H₂O₂ and O₃/UV. Therefore the effluent resulting from the ozonation treatments can be reused in the cork‐processing industry. In a second step, the chemical treatment was conducted by means of UV radiation alone and by the action of hydroxyl radicals, which were generated by the following AOPs: UV/H₂O₂, Fenton's reagent, and photo‐Fenton system. The single photochemical process resulted in 9% of the organic matter present being removed, while the AOPs significantly enhanced this reduction with values in the range 20–75%. Kinetic studies for both groups of treatments were performed, and apparent kinetic rate constants were evaluated. In the ozone‐based experiments, the rate constants ranged from 1846 to 10922 dm³ mol^?1 O₃ h^?1, depending on the operating conditions. In the oxidation experiments using oxidants other than ozone, the rate constants varied between 0.06 and 1.19 h^?1. Copyright © 2004 Society of Chemical Industry     

Multi‐phase electro‐chemical catalytic oxidation of wastewater

The removal of organic pollutants from synthetic wash wastewater by a combined multi‐phase electro‐catalytic oxidation method was evaluated using porous graphite as anode and cathode, and CuO–Co₂O₃–PO₄^3? modified kaolin as catalyst. The synergic effect on COD removal was studied when integrating the electro‐chemical reactor with the effective modified kaolin in a single undivided cell; the results showed that higher COD removal efficiency was obtained than those obtained using the individual processes. Under optimal conditions of pH 3, 30 mA cm^?2 current density, very effective reduction of organic pollutants was achieved with this combined electro‐chemical method. High removal efficiency (90%) of the chemical oxygen demand (COD) was obtained in 60 min in the treatment of simulated wash wastewater (anionic surfactant, sodium dodecyl benzene sulfonate [DBS]). This method was also applied to treat wastewater form paper‐making and resulted in a COD reduction of 84%. Based on the investigation, a possible mechanism of this combined electro‐chemical process was proposed. The pollutants in wastewater could be decreased by the high reactive OH? that were produced via the decomposition of electro‐generated H₂O₂ activated by the synergic effect of electro‐field and catalyst. The results indicate that the multi‐phase catalytic electro‐chemical oxidation process is a promising technique for wastewater treatment. Copyright © 2006 Society of Chemical Industry     

Advanced oxidation of cork‐processing wastewater using Fenton's reagent: kinetics and stoichiometry

This work evaluates Fenton oxidation for the removal of organic matter (COD) from cork‐processing wastewater. The experimental variables studied were the dosages of iron salts and hydrogen peroxide. The COD removal ranged from 17% to 79%, depending on the reagent dose, and the stoichiometric reaction coefficient varied from 0.08 to 0.43 g COD (g H₂O₂)^?1 (which implies an efficiency in the use of hydrogen peroxide varying from 17% to 92%). In a study of the process kinetics, based on the initial rates method, the COD elimination rate was maximum when the molar ratio [H₂O₂]_o:[Fe²⁺]_o was equal to 10. Under these experimental conditions, the initial oxidation rate was 50.5 mg COD dm^?3 s^?1 with a rate of consumption of hydrogen peroxide of 140 mg H₂O₂ dm^?3 s^?1, implying an efficiency in the use of the hydrogen peroxide at the initial time of 77%. The total amount of organic matter removed by Fenton oxidation was increased by spreading the H₂O₂ and ferrous salt reagent over several fractions by 15% for two‐fractions and by 21% for three‐fractions. Copyright © 2004 Society of Chemical Industry     

Removal of ampicillin sodium in solution using activated carbon adsorption integrated with H2O2 oxidation

BACKGROUND: The removal of antibiotic ampicillin sodium using H₂O₂ and modified granular activated carbon (GAC) is discussed. Two types of modified activated carbons were used in experiment to catalyze ·OH production from H₂O₂. One was modified with base (NaOH; called B‐GAC), the other was modified with Fe(NO₃)₃ (Fe‐GAC) and the nominal Fe metal loading was 5 wt%. In the experiment, pH, contact time, dosage of activated carbon and H₂O₂ and initial concentration of ampicillin sodium were investigated to determine their influence on the removal efficiency. The stability of Fe‐GAC was also evaluated. RESULTS: With an initial ampicillin sodium concentration of 200 mg L^?1, 85.2% of chemical oxygen demand (COD) and 76.4% of total organic carbon (TOC) can be removed with 8.0 g L^?1 of B‐GAC and 80 mg L^?1 of H₂O₂ (at pH 5.0). For the Fe‐GAC/H₂O₂ process, with 5.0 g L^?1 of activated carbon and 80 mg L^?1 of H₂O₂, COD and TOC removal can be elevated to 91.2% and 79.5% (at pH 3.0), respectively. CONCLUSION: The integration of activated carbon and H₂O₂ treatment was more effective for the removal of ampicillin from aqueous solution than using activated carbon alone. In the process, adsorption played a dominant role and the addition of a small amount of H₂O₂ accelerated the reaction rate and improved the removal efficiency. pH also greatly affected removal efficiency. Copyright © 2011 Society of Chemical Industry     

Biological Nutrient Removal Using a Novel Laboratory‐Scale Twin Fluidized‐Bed Bioreactor

The capability of biological nutrient removal from wastewater of a novel laboratory‐scale twin fluidized‐bed bioreactor (TFBBR) was studied. The work showed approximately 96 % organic matter, 84 % nitrogen, and 12 % phosphorus removal efficiencies in the first three phases of the study at influent synthetic municipal wastewater (SMW) flow rates of 150, 190, and 240 L/d, with corresponding organic loading rates of 1.3, 1.7, and 2.3 kg COD m^–3 d^–1 and nitrogen loading rates of 0.14, 0.18 and 0.25 kg N m^–3 d^–1. The TFBBR effluent was characterized by <1.0 mg NH₄‐N/L, <4.3 mg NO₃‐N/L, <6 mg TN/L, <6 mg SBOD/L, and 6–10 mg VSS/L. For the three phases, biomass yields of 0.06, 0.066, and 0.071 g VSS/g COD were observed, respectively, which was a significant further reduction in yield compared to the liquid‐solid circulating fluidized‐bed bioreactor technology developed and patented by this research group, of 0.12–0.16 g VSS/g COD. The very low yield was due to a longer solid retention time of 72–108 d.     

Evaluation of Degradation Characteristics of Reactive Dyes by UV/Fenton,UV/Fenton/Activated Charcoal,and UV/Fenton/TiO2 Processes: A Comparative Study

The photochemical decolorization and mineralization of Reactive red 241 (RR241) in aqueous solution has been studied using a homogeneous photofenton process and its combination with activated charcoal and titanium dioxide. The effects of applied catalyst and adsorbent loading, dye concentrations, pH of solution, and the effect of various systems at constant UV irradiation were determined. Decolorization, COD and TOC analysis were employed to evaluate the results of the photochemical and photocatalytic degradation of RR241. The degradation of the dye was monitored by constant COD analysis and then analyzed by high performance liquid chromatography (HPLC) and IR analysis. The result shows that complete decolorization of dye with photofenton process required 240 minutes with 18.6% of maximum TOC reduction. To overcome the problem of slow decolorization and low degradation with photofenton process, it was combines with activated charcoal and Titanium dioxide. UV/Fenton/AC process gave complete decolorization in less than 80 minutes with 14.9% of TOC reduction after 240 minutes. In contrast the UV/Fenton/TiO₂ process required 120 minutes for complete decolorization but yielded maximum TOC reduction of 43.9% after 240 minutes. Therefore, according to COD and TOC reduction it could be suggested that the UV/Fenton/TiO₂ was more effective than other processes.     

The degradation of an azo dye in a batch slurry photocatalytic reactor

The photocatalytic degradation of a commercial azo-reactive textile dye, Remazol Red F-3B, has been investigated in a batch slurry reactor using semiconductor catalysts like, ZnO and TiO₂, and two UV sources emitting mainly at 254 and 365 nm. Non-irradiated catalysts and non-catalyzed UV irradiation have negligible effect on the dye degradation. Initial pH, dye concentration, light power and catalyst loading as well as the catalyst type and UV wavelength are considered as process variables. The results showed that decolorization and TOC removal efficiencies of ZnO are higher under 365 nm UV. On the other hand, when two photocatalysts are compared, the decolorization performance of ZnO is higher than TiO₂ under 365 nm UV_, while TiO₂ performs better under 254 nm UV. Furthermore, from the TOC removal point, TiO₂ performs better than ZnO irrespective of the UV wavelength. TiO₂ irradiated under 254 nm UV degrades successfully both benzene and naphthalene derivatives.     

Removal of 4‐chlorophenol from contaminated water using coconut shell waste pretreated with chemical agents

BACKGROUND: At concentrations higher than 1 mg L^?1, 4‐chlorophenol (4‐CP) is very toxic to living organisms, and if ingested beyond the permitted concentration it causes health disorders such as cancer and mutation. This laboratory study investigates treatment of contaminated water laden with 4‐CP using coconut shell charcoal (CSC) waste. Batch studies were conducted to study the effects of dose, pH, and equilibrium time on 4‐CP removal. To improve 4‐CP removal, surface modification of the adsorbent with TiO₂, HNO₃, and/or NaOH was undertaken. RESULTS: At an initial 4‐CP concentration of 25 mg L^?1 under optimized conditions (dose 13.5 g L^?1, pH 2.0; agitation speed 150 rpm and 50 min equilibrium time), the NaOH‐treated CSC demonstrated a greater removal of 4‐CP (71%) than those oxidized with HNO₃ (40%) and/or coated with TiO₂ (52%). The adsorption capacity of the NaOH‐treated CSC (54.65 mg g^?1) was higher than those treated with HNO₃ (23.13 mg g^?1) or coated with TiO₂ (48.42 mg g^?1). CONCLUSION: Although treatment results using the NaOH‐treated CSC alone were promising, the treated effluents were still unable to meet the required limit of less than 1 mg L^?1. Therefore, subsequent treatments are still required to complement the removal of 4‐CP from the wastewater. Copyright © 2010 Society of Chemical Industry     

Removal of organic contaminants in paper pulp effluents by AOPs: an economic study

The degradation of the organic content of a bleaching Kraft mill effluent was carried out using Advanced Oxidation Processes (AOPs). The study was focused on the identification of the AOP, or combination of AOPs, that showed the highest efficiency together with the lowest cost. Direct UV photolysis (UV), TiO₂ assisted‐photocatalysis (TiO₂/UV), Fenton, Fenton‐like, and photo‐Fenton reactions (Fe(II)/H₂O/UV), UV‐assisted ozonation (O₃/UV) and addition of Fe²⁺ and/or H₂O₂ to the TiO₂/UV and the O₃/UV systems, were used for the degradation of a conventional cellulose bleaching effluent. The effluent was characterized by the general parameters TOC, COD and color, and analyzed for chlorinated low molecular weight compounds using GC–MS. The costs of the systems per unit of TOC reduction were compared. Fenton, Fenton‐like and photo‐Fenton reactions achieved better levels of TOC degradation than photocatalysis and with lower cost's than photocatalytic treatments. Ozonation is an effective but rather expensive process. The use of UVA light, however, increased the effectiveness of ozonation with a significant decrease (>25%) in the operational cost. © 2002 Society of Chemical Industry     

Cost analysis for the degradation of highly concentrated textile dye wastewater with chemical oxidation H2O2/UV and biological treatment

The efficiency and cost‐effectiveness of H₂O₂/UV for the complete decolorization and mineralization of wastewater containing high concentrations of the textile dye Reactive Black 5 was examined. Oxidation until decolorization removed 200–300 mg g^?1 of the dissolved organic carbon (DOC). The specific energy consumption was dependent on the initial dye concentration: the higher concentration required a lower specific energy input on a weight basis (160 W h g^?1 RB5 for 2.1 g L^?1 versus 354 W h g^?1 RB5 for 0.5 g L^?1). Biodegradable compounds were formed, so that DOC removal could be increased by 30% in a following biological stage. However, in order to attain 800 mg g^?1 overall mineralization, 500 mg g^?1 of the DOC had to be oxidized in the H₂O₂/UV stage. A cost analysis showed that although the capital costs are much less for a H₂O₂/UV stage compared to ozonation, the operating costs are almost double those of ozonation. Thus, while H₂O₂/UV can compete with ozonation when the treatment goal only requires decolorization, ozonation is more cost‐effective in this case when mineralization is desired. Copyright © 2006 Society of Chemical Industry     

Photocatalytic degradation of 2,2‐bis(4‐hydroxy‐3‐methylphenyl) propane (BPP) based on molecular recognition interaction

BACKGROUND: Endocrine disruptors in the aquatic environment and their potential adverse effects are currently issues of concern. One of these endocrine disruptors is 2,2‐bis(4‐hydroxy‐3‐methylphenyl)propane (BPP). In this work the molecular recognition interaction of BPP with β‐cyclodextrin (β‐CD) was studied using IR spectroscopy and steady state fluorescence spectroscopy, and the photocatalytic degradation behaviour of BPP based on molecular recognition interaction was investigated in a TiO₂/UV–visible (λ_max = 365 nm) system. This might provide a new method for the treatment of some organic pollutants in wastewater. RESULTS: β‐CD reacts with BPP to form a 1:1 inclusion complex, the formation constant of which is 4.94 × 10³ L mol^?1. The photodegradation rate constant of BPP after molecular recognition by β‐CD showed a 1.42‐fold increase in the TiO₂/UV–visible (λ_max = 365 nm) system. The photodegradation of BPP depended on the concentration of β‐CD, the pH value, the gaseous medium and the initial concentration of BPP. The photodegradation efficiency of BPP with molecular recognition was higher than that without molecular recognition. After 100 min of irradiation the mineralisation efficiency of BPP after molecular recognition by β‐CD reached 94.8%, whereas the mineralisation efficiency of BPP before molecular recognition by β‐CD was only 40.6%. CONCLUSION: The photocatalytic degradation of BPP after molecular recognition by β‐CD can be enhanced in the TiO₂/UV‐visible (λ_max = 365 nm) system. This enhancement is dependent on the enhancement of the adsorption of BPP, the moderate inclusion depth of BPP in the β‐CD cavity and the increase in the frontier electron density of BPP after molecular recognition. Copyright © 2008 Society of Chemical Industry     

Comparative Study of Reactive Dyes Oxidation by H2O2/UV,H2O2/UV/Fe2+ and H2O2/UV/Fe° Processes

The decolorization and mineralization of two reactive dyes C.I. Reactive Blue 4 (RB 4) and C.I. Reactive Blue 268 (RB 268) were studied using various advanced oxidation processes (AOPs) such as H₂O₂/UV, H₂O₂/UV/Fe²⁺, and the H₂O₂/UV/Fe°. All processes were performed within a laboratory-scale photo-reactor setup. The experimental results were assessed in terms of absorbance (A) and total organic carbon (TOC) reduction. The main degradation products were identified by high resolution gas chromatography/high resolution mass spectrometry analyses. The results of our study demonstrated that the additions of moderate concentrations of H₂O₂ and Fe catalyst during the AOPs evidently increased the decolorization efficiencies within the first few minutes of the processing time (5–10 min) for both tested dyes, and prolonged irradiation does not necessarily significantly improve decolorization. On contrary, TOC removal rate increased with the processing time and with the addition of the catalyst from 40–50% up to 70–80% at defined experimental conditions. All the tested AOPs were very successful methods for RB 268 decolorization, having very complex structure and much higher molecular weight compared to the dye RB 4. This is important from both economic and ecological points of view.