共查询到20条相似文献,搜索用时 46 毫秒
1.
采用直径1 m、板间距0.6 m的中试规模冷模塔,以空气和水为物系,对矩形导向浮阀和波纹导向浮阀组合塔板的压降进行了研究。在开孔率为15.25%的条件下,分别考察了10,25,40 m~3/(m·h)液流强度和30,50,70 mm堰高下3种组合方式的塔板压降。实验结果表明:在相同的组合方式下,堰高和液流强度的增加均会导致塔板压降的增加;在堰高和液流强度一定的条件下,弓形区域布置波纹导向浮阀,中间矩形区域布置矩形导向浮阀的组合塔板压降最低。同时文中还对3种组合方式塔板的压降进行了数学方程式拟合,其结果对塔设备设计具有参考价值。 相似文献
2.
《化学工程》2018,(12)
以空气-水物系为介质,在1 000 mm、内置4块塔板的冷模塔中对双阀重组合导向浮阀塔板进行流体力学性能的研究。在开孔率为8.82%、板间距600 mm、堰高50 mm和3种液流强度的条件下,考察了双阀重组合导向浮阀塔板在24%,54%,62%这3种重阀配比下的压降、雾沫夹带和漏液率,并与全轻阀和F1型浮阀塔板进行对比研究。实验结果表明:与全轻阀组合导向浮阀塔板和F1型浮阀塔板相比,双阀重的塔板的雾沫夹带率和漏液率更小,塔板压降变化不大。其中重阀比例54%的组合导向浮阀塔板的雾沫夹带和漏液性能改善明显,塔板压降增加不大,具有一定的工业价值。此外,绘制重阀比例54%的组合导向浮阀塔的负荷性能图,为其工业应用提供指导。 相似文献
3.
4.
5.
采用空气-水作为系统,在直径1 200 mm、内置4层塔板的冷模塔中,对阀腿高度为10 mm、单个开孔尺寸为44 mm x 25 mm的H形导向固阀塔板进行了雾沫夹带实验研究,考察了 3个液流强度、3个堰高因素对雾沫夹带率的影响.同时在开孔率为6.3%的条件下,与阀腿高度为5 mm的H形固阀塔板进行了性能比较,另外还与... 相似文献
6.
7.
8.
设计了一种新型导向筛板-浮片式浮阀复合塔板。在直径为1. 2 m的圆形有机玻璃塔中进行冷模实验,测定了实验塔板在不同条件下的性能参数。实验表明,当液流强度一定、阀孔动能因子升高时,塔板压降、雾沫夹带量和传质效率增大,而漏液量会减小;当阀孔动能因子一定、液流强度升高时,塔板压降、雾沫夹带量和漏液量均会增大,但传质效率会减小。此外,对F1浮阀塔板和ADV浮阀塔板在相同实验条件下进行冷模实验,结果表明,新型导向筛板-浮片式浮阀复合塔板的流体力学性能更好。 相似文献
9.
在直径1.2 m、板间距0.45 m、内置4块塔板的有机玻璃冷模塔内,采用空气-水系统,对Y型导向固阀塔板进行了雾沫夹带性能研究。考察了3种出口堰高、3种液流强度和2种开孔率的改变对Y型导向固阀塔板雾沫夹带性能的影响,并与筛孔型塔板进行对比实验研究。结果表明,Y型导向固阀塔板的雾沫夹带性能随阀孔动能因子的增加呈现出稳定的规律性,在低堰高、低液流强度下表现更优;对比筛孔型塔板,Y型固阀的设计结构表现出明显的抗雾沫夹带优势,同时具有更高的气相负荷操作上限。通过实验数据拟合出了2种开孔率的Y型导向固阀塔板雾沫夹带率的模型方程式,为后续塔板的设计与高黏度物系的分离研究提供参考。 相似文献
10.
《现代化工》2015,(9)
以环己烷-正庚烷物系,在直径为0.75 m、内置4块塔板、40 m2板式再沸器和30 m2板式冷凝器的精馏塔中考察了开孔率、阀孔动能因子、回流比等因素对十字旋阀塔板默弗里板效率的影响。其中开孔率变量是8.22%、11.0%和13.56%;阀孔动能因子变化范围是(5~13)(m/s)(kg/m3)0.5;回流比变量是∞、15、10、8。在开孔率为11.0%,回流比为15的条件下,与F1型浮阀的板效率做了对比。将实验值与AICh E效率模型、变型的Chen-Chuang效率模型的计算值也进行了对比。结果表明,在相同操作条件下,开孔率越大,塔板效率越低,且波动也越大;在相同开孔率条件下,塔板效率随回流减小而变小;基于Liang等的变型Chen-Chuang模型更加适合十字旋阀塔板的板效率预测,其误差较小,为工业设计提供了参考。 相似文献
11.
12.
13.
14.
Anand N. Vennavelli James R. Whiteley Michael R. Resetarits 《Chemical Engineering Research and Design》2014
Existing literature models for predicting the mass transfer efficiencies of binary hydrocarbon, distillation columns employing moving valve trays are evaluated. Only four models for predicting valve tray efficiencies exist in the open literature. All of these models use data from valve trays. The last theoretical model was published in 1972, 42 years ago. By comparison, sieve tray efficiency models are numerous and recent. Sieve tray models were developed from large databases. There are no valve tray equivalents to the fundamental mechanistic models available for sieve trays. Despite the differences between valve and sieve trays, many of the phenomena on sieve and valve trays are similar. Consequently, sieve tray models can be employed to provide estimates for valve trays. In this work, using public FRI data on round moving valves, the performance of the Chen and Chuang sieve tray mechanistic model is compared to the performance of four valve tray models. It appears that, in the absence of fundamental (and qualified) valve tray models, the sieve tray models present a potential alternative for valve tray efficiency predictions. 相似文献
15.
16.
利用通信技术将除尘器脉冲阀和提升阀的运行状态传送到中央控制室。当脉冲阀或提升阀出现问题时,能够及时地发现并处理,避免因除尘器故障造成全线停产。 相似文献
17.
高效液相色谱进样阀在进样过程中,必须是非常清洁的,所以我们必须经常对进样装置进行维护、保养和清洗,否则就会影响定量分析的准确性和重现性,得不到较好的定量分析结果。 相似文献
18.
19.
Asghar Alizadehdakhel Masoud Rahimi Ammar Abdulaziz Alsairafi 《Korean Journal of Chemical Engineering》2009,26(2):475-484
This paper reports experimental and computational fluid dynamics (CFD) modeling studies on the performance of three modified
valves operating in a valve tray column. The original and modified valves including vnotched, warped and double-valve are
tested experimentally. The experimental rig was a Perspex column having a single valve equipped with a fluctuating plate to
measure the quality of gas distribution by using laser sensors. Two-stage nested designs were employed to show the repeatability
and consistency of the measurements. In the CFD modeling, the volume of fluid (VOF) method was used to model the gas-liquid
two-phase flow inside the column. A good agreement was observed between experimental data and the CFD predictions. The results
showed that the double-valve layout provides a better gas distribution, smaller bubbles with greater interface area and lower
pressure drop in comparison with the original and the two other modified valves. 相似文献
20.
文中叙述了以异戊二烯橡胶聚氯乙烯-三元乙丙橡胶并用胶及以异戊二烯橡胶-聚氯乙烯-丁基橡胶并用胶制造的胶垫橡胶对金属材料的粘接性能。试验表明,当ZnO用量很少又不使用白炭黑时,其硫化胶对镀铜钢丝的粘接效果最佳。 相似文献