Application of low loading of collagen in electrospun poly[(l‐lactide)‐co‐(ε‐caprolactone)] nanofibrous scaffolds to promote cellular biocompatibility

Electrospinning of various polymers has been used to produce nanofibrous scaffolds that mimic the extracellular matrix and support cell attachment for the potential repair and engineering of nerve tissue. In the study reported here, an electrospun copolymer of l ‐lactide and ε‐caprolactone (67:33 mol%) resulted in a nanofibrous scaffold with average fibre diameter and pore size of 476 ± 88 and 253 ± 17 nm, respectively. Blending with low loadings of collagen (<2.5% w/w) significantly reduced the average diameter and pore size. The uniformity of fibre diameter distributions was supported with increasing collagen loadings. The nanofibrous scaffolds significantly promoted the attachment and proliferation of olfactory ensheathing cells compared to cells exhibiting asynchronous growth. Furthermore, analysis of cell health through mitochondrial activity, membrane leakage, cell cycle progression and apoptotic indices showed that the nanofibrous membranes promoted cell vigour, reducing necrosis. The study suggests that the use of more cost‐effective, low loadings of collagen supports morphological changes in electrospun poly[(l ‐lactide)‐co‐(ε‐caprolactone)] nanofibrous scaffolds, which also support attachment and proliferation of olfactory ensheathing cells while promoting cell health. The results here support further investigation of the electrospinning of these polymer blends as conduits for nerve repair. © 2013 Society of Chemical Industry     

AB‐ and ABC‐type di‐ and triblock copolymers of poly[styrene‐block‐(ε‐caprolactone)] and poly[styrene‐block‐(ε‐caprolactone)‐block‐lactide]: synthesis,characterization and thermal studies

Polystyrene terminated with benzyl alcohol units was employed as a macroinitiator for ring‐opening polymerization of ε‐caprolactone and L ‐lactide to yield AB‐ and ABC‐type block copolymers. Even though there are many reports on the diblock copolymers of poly(styrene‐block‐lactide) and poly(styrene‐block‐lactone), this is the first report on the poly(styrene‐block‐lactone‐block‐lactide) triblock copolymer consisting of two semicrystalline and degradable segments. The triblock copolymers exhibited twin melting behavior in differential scanning calorimetry (DSC) analysis with thermal transitions corresponding to each of the lactone and lactide blocks. The block derived from ε‐caprolactone also showed crystallization transitions upon cooling from the melt. In the DSC analysis, one of the triblock copolymers showed an exothermic transition well above the melting temperature upon cooling. Thermogravimetric analysis of these block copolymers showed a two‐step degradation curve for the diblock copolymer and a three‐step degradation for the triblock copolymer with each of the degradation steps associated with each segment of the block copolymers. The present study shows that it is possible to make pure triblock copolymers with two semicrystalline segments which also consist of degradable blocks. Copyright © 2009 Society of Chemical Industry     

Synthesis,characterization and biocompatibility of novel biodegradable poly[((R)‐3‐hydroxybutyrate)‐block‐(D,L‐lactide)‐block‐(ε‐caprolactone)] triblock copolymers

BACKGROUND: Biodegradable block copolymers have attracted particular attention in both fundamental and applied research because of their unique chain architecture, biodegradability and biocompatibility. Hence, biodegradable poly[((R )‐3 ‐hydroxybutyrate)‐block‐(D ,L ‐lactide)‐block‐(ε‐caprolactone)] (PHB‐PLA‐PCL) triblock copolymers were synthesized, characterized and evaluated for their biocompatibility. RESULTS: The results from nuclear magnetic resonance spectroscopy, gel permeation chromatography and thermogravimetric analysis showed that the novel triblock copolymers were successfully synthesized. Differential scanning calorimetry and wide‐angle X‐ray diffraction showed that the crystallinity of PHB in the copolymers decreased compared with methyl‐PHB (LMPHB) oligomer precursor. Blood compatibility experiments showed that the blood coagulation time became longer accompanied by a reduced number of platelets adhering to films of the copolymers with decreasing PHB content in the triblocks. Murine osteoblast MC3T3‐E1 cells cultured on the triblock copolymer films spread and proliferated significantly better compared with their growth on homopolymers of PHB, PLA and PCL, respectively. CONCLUSION: For the first time, PHB‐PLA‐PCL triblock copolymers were synthesized using low molecular weight LMPHB oligomer as the macroinitiator through ring‐opening polymerization with D ,L ‐lactide and ε‐caprolactone. The triblock copolymers exhibited flexible properties with good biocompatibility; they could be developed into promising biomedical materials for in vivo applications. Copyright © 2008 Society of Chemical Industry     

Effects of plasma treatment on biocompatibility of poly[(L‐lactide)‐co‐(ϵ‐caprolactone)] and poly[(L‐lactide)‐co‐glycolide] electrospun nanofibrous membranes

Poly[(l ‐lactide)‐co ‐(? ‐caprolactone)] (PLCL) and poly[(l ‐lactide)‐co ‐glycolide] (PLGA) copolymers are widely used in neural guide tissue regeneration. In this research, the surface modification of their hydrophilicity was achieved using plasma treatment. Attachment and proliferation of olfactory ensheathing cells on treated electrospun membranes increased by 26 and 32%, respectively, compared to the untreated PLCL and PLGA counterparts. Cells cultivated on both the PLCL and PLGA membranes showed high viability (>95%) and healthy morphologies with no evidence of cytotoxic effects. Cells grown on treated electrospun fibres displayed significant increases in mitochondrial activity and reductions in membrane leakage when compared to untreated samples. The results suggested that plasma treatment of the surface of the polymers enhanced both cell viability and growth without incurring any cytotoxic effects. © 2017 Society of Chemical Industry     

Synthesis and characterization of poly(L‐lactide‐co‐ϵ‐caprolactone)‐b‐poly(L‐lactide) biodegradable diblock copolyesters: Effect of the block lengths on their thermal properties

Poly(L ‐lactide‐co‐ε‐caprolactone)‐b‐poly(L ‐lactide) [P(LL‐co‐CL)‐b‐PLL] diblock copolyesters were synthesized in a two‐step process with 1‐dodecanol (DDC) and stannous octoate as the initiating system. In the first‐step reaction, a 50:50 mol % amorphous poly(L ‐lactide‐co‐ε‐caprolactone) [P(LL‐co‐CL)] copolyester was synthesized via the bulk copolymerization of L ‐lactide and ε‐caprolactone, which was followed by the polymerization of the PLL crystalline block at the end chain in the second‐step reaction. The yielded copolyesters were characterized with dilute‐solution viscometry, gel permeation chromatography, ¹H‐ and ¹³C‐NMR, and differential scanning calorimetry methods. The molecular weights of the P(LL‐co‐CL) copolyesters from the first‐step reaction were controlled by the DDC concentrations, whereas in the second‐step reaction, the molecular weights of the P(LL‐co‐CL)‐b‐PLL diblock copolyesters depended on the starting P(LL‐co‐CL) copolyester molecular weights and L ‐lactide/prepolymer molar ratios. The starting P(LL‐co‐CL) copolyester molecular weights and PLL block lengths seemed to be the main factors affecting specific thermal properties, including the melting temperature (T_m), heat of melting (ΔH_m), crystallizing temperature (T_c), and heat of crystallizing (ΔH_c), of the final P(LL‐co‐CL)‐b‐PLL diblock copolyester products. T_m, ΔH_m, T_c, and ΔH_c increased when the PLL block lengths increased. However, these thermal properties of the diblock copolyesters also decreased when the P(LL‐co‐CL) block lengths increased. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci, 2007     

Synthesis and characterization of poly(ϵ‐caprolactone)–poly(L‐lactide) diblock copolymers with an organic amino calcium catalyst

The quasiliving characteristics of the ring‐opening polymerization of ?‐caprolactone (CL) catalyzed by an organic amino calcium were demonstrated. Taking advantage of this feature, we synthesized a series of poly(?‐caprolactone) (PCL)–poly(L ‐lactide) (PLA) diblock copolymers with the sequential addition of the monomers CL and L ‐lactide. The block structure was confirmed by ¹H‐NMR, ¹³C‐NMR, and gel permeation chromatography analysis. The crystalline structure of the copolymers was investigated by differential scanning calorimetry and wide‐angle X‐ray diffraction analysis. When the molecular weight of the PLA block was high enough, phase separation took place in the block copolymer to form PCL and PLA domains, respectively. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 102: 2654–2660, 2006     

Synthesis and characterization of ABA triblock and novel multiblock copolymers from ethylene glycol,L‐lactide,and ϵ‐caprolactone

Three types of copolymers were synthesized and characterized. First, triblock ABA copolymers [where A is a homopolymer of ?‐caprolactone and B is poly(ethylene glycol)] were prepared by the ring‐opening polymerization of poly(ethylene glycol) with ?‐caprolactone in the presence of stannous octoate (Sn(Oct)₂). The spectral, thermal, and mechanical properties of one sample of these copolymers were studied, and it was discovered that these types of copolymers were more hydrophilic, possessed lower melting points, and had superior mechanical properties (greater toughness) than poly(?‐caprolactone). Second, triblock ABA copolymers [where A is a homopolymer of L ‐lactide and B is poly(ethylene glycol)] were prepared by the ring‐opening polymerization of poly(ethylene glycol) with L ‐lactide in the presence of Sn(Oct)₂. The mechanical properties of these copolymers were studied, and it was found that they were tougher and softer than poly(L ‐lactide). Third, novel ABA triblock copolymers [where A is a copolymer of ?‐caprolactone and L ‐lactide and B is poly(ethylene glycol)] were prepared, and ¹H‐NMR and ¹³C‐NMR spectra of these copolymers indicated a microblock structure for the two end blocks. The stress–strain behavior revealed low yields and high toughness for these copolymers. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 2072–2081, 2002     

Ring‐opening copolymerization of L‐lactide with ε‐caprolactone initiated by diphenylzinc

Copolymerization of mixtures of L ‐lactide and ε‐caprolactone has been initiated by diphenylzinc. The reaction conditions were investigated, to discover the effects on yield, molecular weight and microstructure of copolymers obtained. The temperature used varied between 50 and 120 °C, the molar ratio of monomer to initiator ranged between 90 and 1440 mol/mol, and the molar ratio of ε‐caprolactone to L ‐lactide employed was between 100/0 and 0/100 mol/mol. Copolymers were characterized by ¹H‐NMR, ¹³C‐NMR, DSC and gel permeation chromatography. The results indicate that incorporation of L ‐lactide to the growing chain is preferred and ε‐caprolactone is copolymerized after most of the L ‐lactide has been depleted. The microstructure of obtained copolyesters was affected considerably by transesterification reactions. It was observed that increasing reaction temperature, reaction time and concentration initiator was advantageous to the transesterification. The crystallinity of copolyester obtained was determined by differential scanning calorimetry. The results are in good agreement with both molar composition and sequence distribution of copolyesters. Copyright © 2006 Society of Chemical Industry     

Enhanced crystallization of poly(L‐lactide‐co‐ε‐caprolactone) during storage at room temperature

Copolymer of L ‐lactide and ε‐caprolactone [P(LLA‐CL)] (50/50) was synthesized using stannous octoate and was stored at room temperature. The change in physical properties occurring during this storage at room temperature was investigated by differential scanning calorimetry (DSC), X‐ray diffractometry, polarizing optical microscopy, tensile and bending tests, and light absorbance measurements. It was concluded that the increase in mechanical properties and light absorbance during storage can be ascribed to gradual selective crystallization of the L ‐lactide sequence in P(LLA‐CL) at room temperature. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 76: 947–953, 2000     

Shape‐memory behaviors of biodegradable poly(L‐lactide‐co‐ϵ‐caprolactone) copolymers

A series of biodegradable poly(L ‐lactide‐co‐?‐caprolactone) (PCLA) copolymers with different chemical compositions are synthesized and characterized. The mechanical properties and shape‐memory behaviors of PCLA copolymers are studied. The mechanical properties are significantly affected by the copolymer compositions. With the ?‐caprolactone (?‐CL) content increasing, the tensile strength of copolymers decreases linearly and the elongation at break increases gradually. By means of adjusting the compositions, the copolymers exhibit excellent shape‐memory effects with shape‐recovery and shape‐retention rate exceeding 95%. The effects of composition, deformation strain, and the stretching conditions on the recovery stress are also investigated systematically. A maximum recovery stress around 6.2 MPa can be obtained at stretching at T_g ? 15°C to 200% deformation strain for the PCLA70 copolymer. The degradation results show that the copolymers with higher ?‐CL content have faster degradation rates and shape‐recovery rates, meanwhile, the recovery stress can maintain a relative high value after 30 days in vitro degradation. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Blends of aliphatic polyesters. VIII. Effects of poly(L‐lactide‐co‐ε‐caprolactone) on enzymatic hydrolysis of poly(L‐lactide), poly(ε‐caprolactone), and their blend films

Poly(L ‐lactide), that is, poly(L ‐lactic acid) (PLLA), poly(ε‐caprolactone) (PCL), and their blend (50/50) films containing different amounts of poly(L ‐lactide‐co‐ε‐caprolactone) (PLLA‐CL), were prepared by solution casting. The effects of added PLLA‐CL on the enzymatic hydrolysis of the films were investigated in the presence of proteinase K and Rhizopus arrhizus lipase by use of gravimetry. The addition of PLLA‐CL decreased the proteinase K–catalyzed hydrolyzabilities of the PLLA and PLLA/PCL (50/50) films as well as the Rhizopus arrhizus lipase‐catalyzed hydrolyzability of the PCL and PLLA/PCL (50/50) films. The decreased enzymatic hydrolyzabilities of the PLLA and PCL films upon addition of PLLA‐CL are attributable to the fact that the PLLA‐CL is miscible with PLLA and PCL and the dissolved PLLA‐CL must disturb the adsorption and/or scission processes of the enzymes. In addition to this effect, the decreased enzymatic hydrolyzabilities of the PLLA/PCL (50/50) films upon addition of PLLA‐CL can be explained by the enhanced compatibility between the PLLA‐rich and PCL‐rich phases arising from the dissolved PLLA‐CL. These effects result in decreased hydrolyzable interfacial area for PLLA/PCL films. The decrement in proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PLLA‐CL, which is miscible with PLLA, was in marked contrast with the enhanced proteinase K–catalyzed hydrolyzability of the PLLA film upon addition of PCL, which is immiscible with PLLA. This confirms that the miscibility of the second polymer is crucial to determine the proteinase K–catalyzed hydrolyzabilities of the PLLA‐based blend films. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 87: 412–419, 2003     

Release of ibuprofen from poly(ε‐caprolactone‐co‐D,L‐lactide) and simulation of the release

A study was made of the effects of the initial ibuprofen load and of the specimen shape on the release of ibuprofen from poly(ε‐caprolactone‐co‐D,L ‐lactide). The mol ratio of the comonomers in the copolymer was 96/4 (caprolactone to lactide) and the experiments were conducted at 37°C in vitro. The results showed that release of ibuprofen is fast and that the rate and profile of the release vary with both the initial load of ibuprofen and the shape of the specimen. The rate of ibuprofen release increases with the initial load and with the surface area‐to‐volume ratio of the specimen, obeying Fickian diffusion. The experimental findings were compared with the results of a mathematical simulation model based on the finite‐difference method. Diffusion parameters needed for the simulation were determined from a separately conducted set of experiments using various methods. For the most part, the results of the simulations and the experiments were in good agreement. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 1279–1288, 2003     

In vitro degradation behavior of electrospun polyglycolide,polylactide, and poly(lactide‐co‐glycolide)

The electrospinning of polyglycolide (PGA), poly(L ‐lactide) (PLA), and poly(lactide‐co‐glycolide) (PLGA; L ‐lactide/glycolide = 50/50) was performed with chloroform or 1,1,1,3,3,3‐hexafluoro‐2‐propanol (HFIP) as a spinning solvent to fabricate their nanofiber matrices. The morphology of the electrospun PGA, PLA, and PLGA nanofibers was investigated with scanning electron microscopy (SEM). The PLGA nanofibers, electrospun with a nonpolar chloroform solvent, had a relatively large average diameter (760 nm), and it had a relatively broad distribution in the range of 200–1800 nm. On the other hand, the PGA and PLA fibers, electrospun with a polar HFIP solvent, had a small average diameter (～300 nm) with a narrow distribution. This difference in the fiber diameters may be associated with the polarity of the solvent. Also, the in vitro degradation of PGA, PLA, and PLGA nanofiber matrices was examined in phosphate buffer solutions (pH 7.4) at 37°C. The degradation rates of the nanofiber matrices were fast, in the order of PGA > PLGA ? PLA. Structural and morphological changes during in vitro degradation were investigated with differential scanning calorimetry and wide‐angle X‐ray diffraction. For the PGA matrix, a significant increase in the crystallinity during the early stage was detected, as well as a gradual decrease during the later period, and this indicated that preferential hydrolytic degradation in the amorphous regions occurred with cleavage‐induced crystallization, followed by further degradation in the crystalline region. © 2004 Wiley Periodicals, Inc. J Appl Polym Sci 95: 193–200, 2005     

Biocompatibility evaluation of glycolide‐containing polyesters in contact with osteoblasts and fibroblasts

Biodegradable aliphatic polyesters have numerous biomedical applications and their capacity to degrade in biological fluids provides the significant advantage of their removal. Three glycolide‐containing aliphatic polyesters: a copolymer of glycolide and L ‐lactide (PGLA), a terpolymer of glycolide, L ‐lactide and ε‐caprolactone (PGLCap) and a copolymer of glycolide, and ε‐caprolactone (PGCap) were tested to evaluate their biocompatibility towards osteoblasts and fibroblasts. Each of the polymer units was previously reported to have acceptable biological properties and good biodegradability, and PGLA is already used for biomedical applications. Here we report that both PGLCap and PGCap affected cell adherence, and compromised cell viability as estimated by flow cytometric analyses of apoptotic and necrotic cells. The two polymers enhanced also production of numerous inflammation‐related factors: nitric oxide, matrix metalloproteinases (MMP‐2 and MMP‐9), and cytokines, including pro‐inflammatory TNF‐α, IL‐1β, IL‐6, and chemokines (IL‐8 or MCP‐1) attracting leukocytes. The effects of PGLCap and PGCap were similar despite the fact that they possess different characteristics: amorphous/smooth surface and semicristalline/rough surface, respectively. However, their common feature, distinctive from PGLA, is a presence of ε‐caprolactone units in their structure. This compound is considered to be acceptably biocompatible but our data suggest that its copolymerization with glycolide and L ‐lactide does not provide satisfactory biocompatibility towards osteoblasts and fibroblasts. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Crystallization and melting behavior of poly(ε‐caprolactone‐co‐δ‐valerolactone) and poly(ε‐caprolactone‐co‐L‐lactide) copolymers with novel chain microstructures

Nuclear magnetic resonance spectroscopy (NMR) characterization of the statistical copolymers of this study showed that the poly(ε‐caprolactone‐co‐L‐lactide)s, with ε‐caprolactone (ε‐CL) molar contents ranging from 70 to 94% and ε‐CL average sequence length (l_CL) between 2.20–9.52, and the poly(ε‐caprolactone‐co‐δ‐valerolactone)s, with 60 to 85% of ε‐CL and l_CL between 2.65–6.08, present semi‐alternating (R→2) and random (R～1) distribution of sequences, respectively. These syntheses were carried out with the aim of reducing the crystallinity of poly(ε‐caprolactone) (PCL), needed to provide mechanical strength to the material but also responsible for its slow degradation rate. However, this was not achieved in the case of the ε‐caprolactone‐co‐δ‐valerolactone (ε‐CL‐co‐δ‐VAL). Non‐isothermal cooling treatments at different rates and isothermal crystallizations (at 5, 10, 21 and 37°C) were conducted by differential scanning calorimetry (DSC), and demonstrated that ε‐CL copolymers containing δ‐valerolactone (δ‐VAL) exhibited a larger crystallization capability than those of L‐lactide (L‐LA) and also arranged into crystalline structures over shorter times. The crystallization enthalpies of the ε‐CL‐co‐δ‐VAL copolymers during the cooling treatments and their heat of fusion (ΔH_m) at the different isothermal temperatures were very large (i.e. ΔH_c > 53 Jg^?1) and in some cases, unrelated to the copolymer composition. In some compositions, such as the 60 : 40, Wide Angle X‐ray Scattering (WAXS) proved that that these two lactones undergo isomorphism and co‐crystallize in a single cell. © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 42534.     

Hydrolytic Degradation of Amorphous Films of L‐Lactide Copolymers with Glycolide and D‐Lactide

Summary: Films of poly(L ‐lactic acid) (PLLA) and copolymers of L ‐lactide (LLA) with either glycolide [P(LLA‐GA)](81/19) or D ‐lactide [P(LLA‐DLA)](77/23) were prepared and an effect of comonomer type on the hydrolytic degradation of the films was studied in phosphate‐buffered solutions at 37 °C. The degraded films were investigated using gravimetry (weight loss and water absorption), gel permeation chromatography, DSC, X‐ray diffractometry, tensile testing and polarization optical microscopy. To exclude the effects of molecular weight and crystallinity on hydrolytic degradation, the films were prepared from polymers with similar molecular weights and were made amorphous by melt quenching. It was found that the hydrolytic degradation rate decreased in the order P(LLA‐GA) > P(LLA‐DLA) > PLLA. The hydrolytic degradation rate constant of PLLA and LLA copolymer films increased with increasing the water absorption (hydrophilicity), or with decreasing the initial glass transition temperature or the L ‐lactyl unit sequence length, indicating that the hydrolytic degradation rate of the copolymers was closely related to these three parameters. The crystallization of P(LLA‐GA) film occurred within hydrolytic degradation for 20 weeks.

M_n of PLLA and LLA copolymer films as a function of hydrolytic degradation time.     

Hydrolytic degradation and crystallization behavior of linear 2‐armed and star‐shaped 4‐armed poly(l‐lactide)s: Effects of branching architecture and crystallinity

“Linear” aliphatic polyesters composed of two poly(l ‐lactide) arms attached to 1,3‐propanediol and “star‐shaped” ones composed of four poly(l ‐lactide) arms attached to pentaerythritol (2‐L and 4‐L polymers, respectively) with number‐average molecular weight (M_n) = 1.4–8.4 × 10⁴g/mol were hydrolytically degraded at 37°C and pH = 7.4. The effects of the branching architecture and crystallinity on the hydrolytic degradation and crystalline morphology change were investigated. The degradation mechanism of initially amorphous and crystallized 2‐L polymers changed from bulk degradation to surface degradation with decreasing initial M_n; in contrast, initially crystallized higher molecular weight 4‐L polymer degraded via bulk degradation, while the degradation mechanism of other 4‐L polymers could not be determined. The hydrolytic‐degradation rates monitored by molecular‐weight decreases decreased significantly with increasing branch architecture and/or higher number of hydroxyl groups per unit mass. The hydrolytic degradation rate determined from the molecular weight decrease was higher for initially crystallized samples than for initially amorphous samples; however, that of 2‐L polymers monitored by weight loss was larger for initially amorphous samples than for initially crystallized samples. Initially amorphous 2‐L polymers with an M_n below 3.5 × 10⁴g/mol crystallized during hydrolytic degradation. In contrast, the branching architecture disturbed crystallization of initially amorphous 4‐L polymers during hydrolytic degradation. All initially crystallized 2‐L and 4‐L polymers had δ‐form crystallites before hydrolytic degradation, which did not change during hydrolytic degradation. During hydrolytic degradation, the glass transition temperatures of initially amorphous and crystallized 2‐L and 4‐L polymers and the cold crystallization temperatures of initially amorphous 2‐L and 4‐L polymers showed similar changes to those reported for 1‐armed poly(l ‐lactide). © 2015 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2015 , 132, 41983.     

Preparation,characterization, and drug release behaviors of drug‐loaded ε‐caprolactone/L‐lactide copolymer nanoparticles

Copolymers of ε‐caprolactone and L ‐lactide (PCLLA) with different monomer ratio were synthesized by ring opening polymerization, and drug‐loaded nanoparticles of poly‐ε‐caprolactone (PCL), poly‐L ‐lactide (PLLA), and their copolymers were prepared by precipitation method, respectively. The results of differential scanning calorimetry and X‐ray diffraction indicated that the copolymerization of PCLLA decreased the crystallinity of the polymers, and the results of transmission electron micrograph and laser light scattering (LLS) revealed that the prepared nanoparticles had a spherical shape, and the size of PCLLA nanoparticles (∼ 85 nm) was smaller than that of the PCL and PLLA nanoparticles. The experiment of in vitro drug release showed that the drug release rate from PCLLA nanoparticles was slower than that from PCL and PLLA nanoparticles, and the release profile of PCL6/LA4 nanoparticles appeared to follow zero order kinetics. These results suggested that the polymer composition made a great influence on the nanoparticle size and drug release behavior. © 2000 John Wiley & Sons, Inc. J Appl Polym Sci 75: 874–882, 2000     

Properties and degradation behavior of surface functionalized MWCNT/poly(L‐lactide‐co‐ε‐caprolactone) biodegradable nanocomposites

In this research, poly(L ‐lactide‐co‐ε‐caprolactone) (PLACL) reinforced with well‐dispersed multiwalled carbon nanotubes (MWCNTs) nanocomposites were prepared by oxidization and functionalization of the MWCNT surfaces using oligomeric L ‐lactide (LA) and ε‐caprolactone (CL). It is found that the surface functionalization can effectively improve the dispersion and adhesion of MWCNTs in PLACL. The surface functionalization will have a significant effect on the physical, thermomechanical, and degradation properties of MWCNT/PLACL composites. The tensile modulus, yield stress, tensile strength, and elongation at break of composite increased 49%, 60%, 70%, and 94%, respectively, when the concentration of functionalized MWCNTs in composite is 2 wt %. The in vitro degradation rate of nanocomposites in phosphate buffer solution increased about 100%. The glass transition temperature (T_g) of composites was decreased when the concentration of functionalized MWCNTs is 0.5 wt %. With further increasing the concentration of functionalized MWCNTs, the T_g was increased. The degradation kinetics of nanocomposites can be engineered and functionalized by varying the contents of pristine or functionalized MWCNTs. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Optimization and investigation of the governing parameters in electrospinning the home‐made poly(l‐lactide‐co‐ε‐caprolactone‐diOH)

Poly(l ‐lactide‐co‐ε‐caprolactone‐diOH) (PCLA) with (ABA)_n type is synthesized using poly(lactic acid) (PLA) and poly(ε‐caprolactone) di‐OH (PCL‐diOH) via chain extending method. FT‐IR, ¹H‐NMR, and GPC data demonstrate that PLA and PCL‐diOH have reacted completely. The product is electrospun into ultrafine fibers subsequently. The optimum electrospinning parameters obtain from an orthogonal experiment are a solvent ratio (DMF/DCM) of 5/5, a polymer concentration of 28 wt %, a collector distance of 20 cm and a voltage of 18 kV. As a result, the average diameter of fibers is 0.77 µm and the uniformity is above 80%. Via range analysis, it is found that the order of the influence on diameter is solvent ratio, applied voltage, collector distance, and polymer concentration, successively. Single effect of the four governing factors on diameter and morphology is also experimentally investigated. This may provide clues for obtaining fibers with various structures by controlling the parameters. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 130: 3600–3610, 2013