Silyl-Crosslinked Urethane Elastomer Modifying Epoxy Resin: I. Morphological Studies

Silyl-crosslinked urethane elastomer modifying epoxy resin has drawn much interest. Here triethoxysilyl-terminated polycaprolactone elastomer (PCL-TESi) modifying diglycidylether of bisphenol A epoxy resins (DGEBA) system was chosen; then the effect of the type of curing agent on the phase structure of the studied system was investigated. The modified systems with different phase structures were obtained by varying the formulations of the curing agents. It was experimentally shown that the crosslinked density was greatly increased by the addition of an aminosilane curing agent (KBE-9103). And the SEM and TEM analysis of the cured system showed that the addition of KBE-9103 increased the compatibility between the PCL-TESi and DGEBA, but decreased the ductility of the systems. The TEM results indicated that the addition of too much of the KBE-9103 made the resulting silicone particles coagulate with each other. The state of phase separation from the TEM in the cured system was explained theoretically. These considerations would serve the deeper studies of the mechanism of silyl-crosslinked urethane elastomer modifying epoxy resin in the future.     

Preparation and properties of soybean oil–based curing agents for epoxy resin

In order to improve the flexibility properties of conventional epoxy resin, two novel soybean oil–based curing agents were synthesized. The curing agent obtained from the reaction between epoxy soybean oil and ethylene diamine was named EEDA, and another curing agent derived from epoxy soybean oil and isophorone diamine was named EIPDA. Several techniques were used to systematically investigate the effects of the structure and content of the two curing agents on the properties of the cured products. The Fourier transform infrared analysis demonstrated that epoxy resin reacted with soybean oil–based curing agents. The differential scanning calorimetry analysis showed that the curing process between diglycidyl ether of bisphenol‐A (DGEBA) and soybean oil–based curing agents only had an exothermic peak. Thermogravimetric analysis indicated that the cured DGEBA/EIPDA system was more stable than the DGEBA/EEDA system below 300 °C. Mechanical tests and Shore D hardness tests suggested that excessive EEDA greatly enhanced the toughness of cured products because of the introduction of aliphatic chains.© 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44754.     

Curing kinetics and reaction‐induced homogeneity in networks of poly(4‐vinyl phenol) and diglycidylether epoxide cured with amine

Mixtures of diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin with poly(4‐vinyl phenol) (PVPh) of various compositions were examined with a differential scanning calorimeter (DSC), using the curing agent 4,4′‐diaminodiphenylsulfone (DDS). The phase morphology of the cured epoxy blends and their curing mechanisms depended on the reactive additive, PVPh. Cured epoxy/PVPh blends exhibited network homogeneity based on a single glass transition temperature (T_g) over the whole composition range. Additionally, the morphology of these cured PVPh/epoxy blends exhibited a homogeneous network when observed by optical microscopy. Furthermore, the DDS‐cure of the epoxy blends with PVPh exhibited an autocatalytic mechanism. This was similar to the neat epoxy system, but the reaction rate of the epoxy/polymer blends exceeded that of neat epoxy. These results are mainly attributable to the chemical reactions between the epoxy and PVPh, and the regular reactions between DDS and epoxy. Polym. Eng. Sci. 45:1–10, 2005. © 2004 Society of Plastics Engineers.     

Preparation of a light color cardanol-based curing agent and epoxy resin composite: Cure-induced phase separation and its effect on properties

A light color cardanol-based epoxy curing agent (MBCBE) was synthesized from cardanol butyl ether, formaldehyde and diethylenetriamine. In comparison, a phenalkamine with a similar structure was also prepared. The chemical structures were confirmed by GC–MS and FTIR. The cure behaviors of diglycidyl ether of bisphenol A (DGEBA) with these two curing agents was studied by differential scanning calorimetry (DSC). The morphology, mechanical properties, thermal properties of the cured epoxies were also investigated. The DSC results indicated that MBCBE is less reactive than the phenalkamine. The morphology of the cured MBCBE/DGEBA consisted of cavities dispersed within a continuous epoxy matrix. The cavities markedly improved the lap shear strength and impact strength of the cured resin. Both the two cured resins indicated a two-stage decomposition mechanism. Compared with PKA/DGEBA, the weight loss of MBCBE/DGEBA at the first stage was mainly resulted from the dispersed phase in the epoxy matrix.     

Preparation and Application of a New Curing Agent for Epoxy Resin

A new curing agent based on palmitoleic acid methyl ester modified amine (PAMEA) for epoxy resin was synthesized and characterized. Diglycidyl ether of bisphenol A (DGEBA) epoxy resins cured with different content of PAMEA along with diethylenetriamine (DETA) were prepared. The mechanical properties, dynamic mechanical properties, thermal properties, and morphology were investigated. The results indicated that the PAMEA curing agent can improve the impact strength of the cured epoxy resins considerably in comparison with the DETA curing agent, while the modulus and strength of the cured resin can also be improved slightly. When the PAMEA/epoxy resin weight ratio is 30/100, the comprehensive mechanical properties of the cured epoxy resin are optimal; at the same time, the crosslinking density and glass transition temperature of the cured epoxy resin are maximal.     

Novel amine terminated elastomeric oligomers and their effects on properties of epoxy resins as a toughener

The objective of this study was to investigate the effects of amine terminated elastomeric epoxy tougheners on the mechanical and thermal properties of diglycidyl ether of bisphenol A based epoxy resin. The amine terminated polycaprolactone (PCL) (1) and PCL‐PDMS‐PCL (2) based oligomers were synthesized and characterized by FTIR spectroscopy. The stoichiometrical amount of the reactive oligomers as toughener, reactive epoxy resin and the curing agent, 4,4′‐diaminodiphenyl sulfone (DDS) were mixed and degassed. The homogenous mixtures were cured at 120°C into the preheated molds. The mechanical and thermal characterizations of toughened epoxy resin system were evaluated. It has been shown that the mechanical and thermal properties of toughened epoxy system vary as a function of the chemical structure and the concentration of rective oligomers. Higher mechanical properties were obtained for epoxy resin toughened by PCL‐PDMS‐PCL (2) based oligomer. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

Synthesis of polysiloxane‐type multifunctional flame retardant and its application in epoxy systems

Polymethyl(3‐glycidyloxypropyl)siloxane (PMGS) was synthesized as a flame‐retardant additive, which were cocured with diglycidyl ether of bisphenol‐A (DGEBA) using 4,4′‐diaminodiphenylsulfone as a curing agent. The structure of PMGS was confirmed through Fourier transform infrared and ¹H‐NMR spectra. The cured products were characterized with dynamic mechanical thermal analysis, thermogravimetric analysis, and oxygen index analyzer. With PMGS incorporated, the cured epoxy resin showed better thermal stability, higher limited oxygen index, and higher char yield. At moderate loading of PMGS, the storage modulus and glass transition temperature of the cured epoxy resin based on neat DGEBA were obviously improved. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011     

Influence of rubber on the curing kinetics of DGEBA epoxy and the effect on the morphology and hardness of the composites

The influence of the end groups of two liquid rubbers on curing kinetics, morphology, and hardness behavior of diglycidyl ether of bisphenol-A based epoxy resin (DGEBA) has been studied. The rubbers are silyl-dihydroxy terminated (PDMS-co-DPS-OH) and silyl-diglycidyl ether terminated (PDMS-DGE). Crosslinking reactions, investigated by shear rheometry, ranged 90–110 °C, using a constant concentration (5 phr) of liquid rubbers and 1,2-Diamino cyclohexane (1,2-DCH) as hardener agent. The gel time, t _gel, of the neat epoxy significantly decreased when adding the elastomers, more so for the silyl-dihydroxy terminated elastomer; at 110 °C the reaction was nearly complete before rheological test started. The results suggest that the elastomers induced a catalytic effect on the curing reaction. Scanning electron microscopy revealed phase separation of the elastomer during the curing reaction with rubber domains about 5 μm size. However, the DGEBA/dihydroxy terminated elastomer composite cured at 110 °C exhibited a homogenous morphology, that is, the rapid reaction time would not allow for phase separation. Water contact angle tests evidenced either more hydrophilic (silyl-diglycidyl ether terminated rubber) or more hydrophobic (silyl-dihydroxy terminated rubber) behavior than the neat epoxy. The latter effect is attributed to the presence of aromatic rings in the backbone structure of PDMS-co-DPS-OH. Microindentation measurements show that the elastomers significantly reduced the hardness of the epoxy resin, the DGEBA/ether terminated composite exhibiting the lowest hardness values. Moreover, hardness increased as reaction temperature did, correlating with a reduction of microdomains size thus enabling the tuning of mechanical properties with reaction temperature.     

Epoxy resin containing the poly(sily ether): Preparation,morphology, and mechanical properties

The poly(sily ether) with pendant chloromethyl groups (PSE) was synthesized by the polyaddition of dichloromethylsilane (DCM) and diglycidylether of bisphenol A (DGEBA) with tetrabutylammonium chloride (TBAC) as a catalyst. This polymer was miscible with diglycidyl ether of bisphenol A (DGEBA), the precursor of epoxy resin. The miscibility is considered to be due mainly to entropy contribution because the molecular weight of DGEBA is quite low. The blends of epoxy resin with PSE were prepared through in situ curing reaction of diglycidyl ether of bisphenol A (DGEBA) and 4,4′‐diaminodiphenylmethane (DDM) in the presence of PSE. The DDM‐cured epoxy resin/PSE blends with PSE content up to 40 wt % were obtained. The reaction started from the initial homogeneous ternary mixture of DGEBA/DDM/PSE. With curing proceeding, phase separation induced by polymerization occurred. PSE was immiscible with the 4,4′‐diaminodiphenylmethane‐cured epoxy resin (ER) because the blends exhibited two separate glass transition temperatures (T_gs) as revealed by the means of differential scanning calorimetry (DSC) and dynamic mechanical analysis (DMA). SEM showed that all the ER/PSE blends are heterogeneous. Depending on blend composition, the blends can display PSE‐ or epoxy‐dispersed morphologies, respectively. The mechanical test showed that the DDM‐cured ER/PSE blend containing 25 wt % PSE displayed a substantial improvement in Izod impact strength, i.e., epoxy resin was significantly toughened. The improvement in impact toughness corresponded to the formation of PSE‐dispersed phase structure. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 89: 505–512, 2003     

Partially fluorinated polymer networks: Synthesis and structural characterization

Functionalizacion of epoxy‐based networks by the preferential surface enrichment of perfluorinated tails to achieve hydrophobic surface is described. The selected fluorinated epoxies (FE) were: 2,2,3,3,4,4,5,5,6,6,7,7,8,9,9,9‐hexadecafluoro‐8‐trifluoromethyl nonyloxirane (FED3) and 2,2,3,3,4,4,5,5,6,6,7,7,8,8,9,9,9‐heptadecafluoro nonyloxirane (FES3). Two series of crosslinked fluorinated epoxy‐based materials containing variable fluorine contents (from 0 to 5 wt % F) were prepared using formulations based on partially fluorinated diamine, epoxy monomer and a curing agent. The epoxy monomer was based on diglycidyl ether of bisphenol A (DGEBA) while the curing agents were either propyleneoxide diamine (JEFFAMINE) or 4,4′‐methylenebis(3‐chloro 2,6‐diethylaniline) (MCDEA). It was found that depending on the curing agent employed, homogeneous distribution of fluorine or phase separation distinguishable at micrometer or nanometer scale was obtained when curing blends initially homogeneous. The morphology and composition of partially fluorinated networks were investigated on a micrometer scale combining scanning electron microscopy and X‐ray analysis. When curing with JEFFAMINE, samples were homogeneous for all fluorine proportions. In contrast, MCDEA‐cured blends showed fluorine‐rich zones dispersed in a continuous epoxy‐rich phase. A completely different morphology, characterized by a distribution of irregular fluorine‐rich domains dispersed in an epoxy‐rich phase, was obtained when curing blends initially immiscible. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2011.     

Aging behavior of a hot‐cured epoxy system

The thermal and hydro‐thermal aging of a hot‐cured epoxy system (diglycidylether of bisphenol A (DGEBA) + dicyandiamide (DDA)) in the glassy state is revisited using DSC and IR attenuated total reflection spectroscopy. Because of the diffusion of DDA from the solid particles into the liquid DGEBA matrix, curing produces a highly crosslinked amorphous matrix that contains low crosslinked amorphous regions. After full curing, the network possesses a relatively low molecular mobility and no residual reactive groups. Thermal and hydro‐thermal loading is performed at 60°C, well below the principal glass transition temperature (T_g1 = 171°C). Both aging regimes cause significant chemical and structural changes to the glassy epoxy. It undergoes a phase separation of relatively mobile segments inside the low mobile matrix, providing a second glass transition that shifts from T_g2 = 86–114°C within 108 days of aging. This phase separation is reversible on heating into the viscoelastic state. Hydro‐thermal aging leads to a reversible and a nonreversible plasticizing effect as well. On thermal aging, no chemical changes are observed but hydro‐thermal aging causes significant chemical modifications in the epoxy system. These modifications are identified as a partial degradation of crosslinks produced by the cyano groups of the DDA and correspond to the nonreversible plasticitation. These changes in the cured epoxy should exert an influence on the mechanical properties of an adhesive bond. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006     

Rheology and curing characteristics of epoxy–clay nanocomposites

Diglycidyl ethers of bisphenol‐A (DGEBA) epoxy resin, filled separately with organoclay (OC) and unmodified clay (UC), were synthesized at room temperature and at high temperature (80 °C) by mechanical shear mixing. The room temperature curing (RTC) and high temperature curing (HTC) were carried out with the addition of triethylene tetramine (TETA) and diaminodiphenylmethane (DDM) curing agents respectively. The OC used was alkyl ammonium modified montmorillonite (MMT) and the UC was Na⁺‐MMT. X‐ray diffraction (XRD) and transmission electron microscopy (TEM) were used to study the structure and morphology of the nanocomposites. The influence of OC and UC particles on rheology and curing characteristics was studied. The rate of increase in viscosity was higher for OC‐filled resin than that of the UC‐filled resin. The curing study showed that the amine ions of the OC aided the polymerization process and favoured the curing at low temperature over the curing of unfilled epoxy resin. The tensile properties were enhanced for epoxy filled with OC particles rather than those filled with UC particles. Copyright © 2005 Society of Chemical Industry     

Synthesis and properties of poly(urethane‐imide) diacid/epoxy composites cured with an aziridine system

A poly(urethane‐imide) diacid (PUI), a diimide‐diacid with a soft structure unit, was directly synthesized from the reaction of trimellitic anhydride and isocyanate terminated polyurethane prepolymer. FT‐IR and NMR were used to characterize its chemical structure. Then PUI was blended with two types of epoxy resins with different chemical structures, diglycidyl ether of bisphenol A (DGEBA) and novolac epoxy (EPN). After curing the blends with polyfunctional aziridine CX‐100, novel polyurethane/epoxy composites were obtained as transparent yellowish films. Thermal, chemical, and morphological properties of the cured composites were investigated using thermal analysis, SEM, TEM, chemical resistance, respectively. All experimental data indicated that epoxy modified PUI composites possessed higher thermal stability than that unmodified PUI, and that modified PUI had much better chemical resistance. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Morphology,viscoelastic properties,and mechanical behavior of epoxy resin modified with hydroxyl‐terminated poly(ether ether ketone) oligomer with pendent tert‐butyl groups

Hydroxyl‐terminated poly (ether ether ketone) with pendent tert‐butyl groups (PEEKTOH) synthesized from 4,4′‐difluorobenzophenone and tert‐butyl hydroquinone was blended with diglycidyl ether of bisphenol‐A (DGEBA) epoxy resin. A diamine, 4,4′‐diaminodiphenyl sulfone (DDS) was used as the curing agent. The thermal and mechanical properties, fracture toughness, and morphology of the blends were investigated. Morphological analysis of the blends revealed a particulate structure with PEEKTOH phase dispersed in the epoxy matrix. Unlike classical polymer blend systems, increase in concentration of PEEKTOH does not increase the domain size. Instead, a decrease is obtained. The fracture toughness increased with the addition of oligomer without much decrease in tensile and flexural strengths. Addition of 15 phr oligomer gave maximum toughness. The dispersed PEEKTOH initiated several mechanisms that improved the fracture toughness of the blends. The cross‐link density calculated from the storage modulus in the rubbery plateau region decreased with the increase in PEEKTOH. The thermal stability of epoxy resin remained unaffected even after blending with PEEKTOH. POLYM. ENG. SCI., 45:1645–1654, 2005. © 2005 Society of Plastics Engineers     

Hybridization of aqueous PU/epoxy resin via a dual self‐curing process

Amino‐terminated and carboxyl‐containing polyurethane (PU) is prepared by an isocyanate‐terminated PU prepolymer process. Carboxyl‐containing epoxy resin is obtained from a half‐esterification of epoxy resin with maleic anhydride. These two aqueous resins are obtained after neutralization with triethylamine and dispersion into water phase, respectively. A latent curing agent (TMPTA‐AZ) is prepared by a Michael addition of aziridine with trimethylolpropane triacrylate (TMPTA). A self‐curing system of PU/epoxy hybrid is obtained from a blending of these two aqueous resins with latent curing agent. PU/epoxy hybrid is derived from two self‐curing reactions on drying. The first curing for hybridization between PU amino groups with oxirane groups of epoxy resin is via a ring‐opening reaction and the secondary curing takes place on carboxyl groups of PU/epoxy hybrid with aziridine of TMPTA‐AZ. The final properties of these dual self‐cured PU/epoxy hybrids are reported. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Curing of diglycidyl ether of bisphenol‐A epoxy resin using a poly(aryl ether ketone) bearing pendant carboxyl groups as macromolecular curing agent

BACKGROUND: Reactive thermoplastics have received increasing attention in the field of epoxy resin toughening. This paper presents the first report of using a novel polyaryletherketone bearing one pendant carboxyl group per repeat unit to cure the diglycidyl ether of bisphenol‐A epoxy resin (DGEBA). The curing reactions of DGEBA/PEK‐L mixtures of various molar ratios and with different catalysts were investigated by means of dynamic differential scanning calorimetry and Fourier transform infrared (FTIR) spectroscopy methods. RESULTS: FTIR results for the DGEBA/PEK‐L system before curing and after curing at 135 °C for different times demonstrated that the carboxyl groups of PEK‐L were indeed involved in the curing reaction to form a crosslinked network, as evidenced by the marked decreased peak intensities of the carboxyl group at 1705 cm^?1 and the epoxy group at 915 cm^?1 as well as the newly emerged strong absorptions of ester bonds at 1721 cm^?1 and hydroxyl groups at 3447 cm^?1. Curing kinetic analysis showed that the value of the activation energy (E_a) was the highest at the beginning of curing, followed by a decrease with increasing conversion (α), which was attributed to the autocatalytic effect of hydroxyls generated in the curing reaction. CONCLUSION: The pendant carboxyl groups in PEK‐L can react with epoxy groups of DGEBA during thermal curing, and covalently participate in the crosslinking network. PEK‐L is thus expected to significantly improve the fracture toughness of DGEBA epoxy resin. Copyright © 2009 Society of Chemical Industry     

Preparation,curing kinetics,and thermal properties of bisphenol fluorene epoxy resin

Diglycidyl ether of 9,9‐bis(4‐hydroxyphenyl) fluorene (DGEBF) was synthesized to introduce more aromatic structures into an epoxy resin system. The structure of DGEBF was characterized with Fourier transform infrared and ¹H‐NMR. 4,4′‐Diaminodiphenylmethane (DDM) was used as the curing agent for DGEBF, and differential scanning calorimetry was applied to study the curing kinetics. The glass‐transition temperature of the cured DGEBF/DDM, determined by dynamic mechanical analysis, was 260°C, which was about 100°C higher than that of widely used diglycidyl ether of bisphenol A (DGEBA). Thermogravimetric analysis was used to study the thermal degradation behavior of the cured DGEBF/DDM system: its onset degradation temperature was 370°C, and at 700°C, its char yield was about 27%, whereas that of cured DGEBA/DDM was only 14%. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 2007     

Synthesis and characterization of diphenylsilanediol modified epoxy resin and curing agent

A series of diphenylsilanediol modified epoxy resins and novel curing agents were synthesized. The modified epoxy resins were cured with regular curing agent diethylenetriamine (DETA); the curing agents were applied to cure unmodified diglycidyl ether of bisphenol A epoxy resin (DGEBA). The heat resistance, mechanical property, and toughness of all the curing products were investigated. The results showed that the application of modified resin and newly synthesized curing agents leads to curing products with lower thermal decomposition rate and only slightly decreased glass transition temperature (T_g), as well as improved tensile modulus and tensile strength. In particular, products cured with newly synthesized curing agents showed higher corresponding temperature to the maximum thermal decomposition rate, comparing with products of DGEBA cured by DETA. Scanning electron microscopy micro images proved that a ductile fracture happened on the cross sections of curing products obtained from modified epoxy resins and newly synthesized curing agents, indicating an effective toughening effect of silicon–oxygen bond.     

Curing of epoxy–urethane copolymers in a heated mold: Effect of the curing conditions on the phase‐separation process

The curing process of an epoxy–urethane copolymer in a heated mold was studied. The epoxy resin (DGEBA, Araldyt GY9527; Ciba Geigy), was coreacted with a urethane prepolymer (PU, Desmocap 12; Bayer) through an amine that acted as crosslinking agent (mixture of cycloaliphatic amines; Distraltec). The study focused on the effect of the curing condition and PU concentration on time–temperature profiles measured in the mold and the consequent final morphologies obtained. As the PU concentration increases, the maximum temperature reached in the mold decreases as a result of the dilution effect of the elastomer on reaction heat, whereas the T_g of the piece also decreases. Phase separation is a function of conversion and temperature reached in the curing part and was analyzed using experimental data and a mathematical model that predicts temperature and conversion throughout the thickness of the mold. Scanning electron microscopy and atomic force microscopy were used to determine the characteristics of the dispersed phase for the different formulations and conditions of curing. It was shown that the size of the dispersed phase increased with the initial PU concentration, whereas there were practically no differences in the separated phase as a function of position or temperature of curing (in the range of 70 to 100°C studied). The superposition of the phase diagrams with the conversion–temperature trajectories during cure provided an explanation of the morphologies generated. © 2001 John Wiley & Sons, Inc. J Appl Polym Sci 81: 889–900, 2001     

Phase Separation of Poly(ether sulfone imide) Modified Epoxy Resins

Amine terminated poly(ether sulfone imide) (PESI) with various imide and ethersulfone contents but similar polymer molecular weights were blended with diglycidyletherbisphenol-A (DGEBA) and cured with diaminodiphenylsulfone (DDS). The imide group, a tertiary amine, is a catalyst of the curing reaction of DGEBA with DDS, but it is poorly compatible with uncured epoxy resin. The ethersulfone group is not a catalyst of the curing reaction of DGEBA with DDS, but it has a similar chemical structure as DDS and is compatible with epoxy resin while it is at a low degree of curing. Since PESIs used in this study had similar molecular weights, increasing imide content of PESI would reduce ethersulfone content. The influence of imide and ethersulfone contents of PESI on the phase separation and curing reaction of DGEBA/DDS/PESI blend was investigated using differential scanning calorimetry (DSC), time-resolved light scattering (TRLS), and polarized optical microscopy (POM). Though the imide group has a catalysis effect on the curing reaction of DGEBA with DDS, however, its poor compatibility with epoxy resin retards the curing reaction. Our experimental results revealed the morphology of the cured blends and the curing behavior was a compromise result of catalysis and compatibility of PESI with epoxy resin.