Thermoplastic vulcanizates based on maleated natural rubber/polypropylene blends: Effect of blend ratios on rheological,mechanical, and morphological properties

Maleated natural rubber (MNR) was prepared and used to formulate thermoplastic vulcanizates (TPVs) based on various MNR/PP blends. The influence of mixing methods on the TPVs properties was first studied. We found that mixing all ingredients in an internal mixer provided the TPVs with better mechanical properties. The final mixing torque, shear stress, and shear viscosity of the TPVs prepared with various blend ratios of MNR/PP increased with increasing levels of MNR in the blends. This may be attributed to higher shear viscosity of the pure MNR than that of the pure PP. Furthermore, as evidenced in SEM micrographs, the TPVs are two phase morphologies with dispersed small vulcanized rubber domains in the PP matrix. Therefore, the higher content of PP caused the more molten continuous phase of the flow during mixing and rheological characterization. Tensile strength and hardness of the TPVs increased with increasing levels of PP, while the elongation at break decreased. Furthermore, the elastomeric properties, in terms of tension set, increased with increasing levels of MNR in the blends. This may be attributed to decreasing trends in the size of vulcanized rubber particles dispersed in the PP matrix with an increasing concentration of MNR. POLYM. ENG. SCI. 46:594–600, 2006. © 2006 Society of Plastics Engineers.     

Multifunctional peroxide as alternative crosslink agents for dynamically vulcanized epoxidized natural rubber/polypropylene blends

Commonly used dicumyl peroxide (DCP) in combination with coagent, triallyl cyanurate (TAC), as a crosslinking agent is well acceptable for dynamically vulcanized rubber phase of thermoplastic vulcanizates (TPVs). However, it generally produces volatile decomposition products, which cause a typical unpleasant smell and a blooming phenomenon. In this work, influence of two types of multifunctional peroxides: 2,4‐diallyloxy‐6‐tert‐butylperoxy‐1,3,5‐triazine (DTBT) and 1‐(2‐tert‐butylperoxyisopropyl)‐3‐isopropenyl benzene (TBIB), on properties of TPVs based on epoxidized natural rubber (ENR)/polypropylene (PP) blends were investigated. The conventional peroxide/coagent combinations, i.e., DCP/TAC and tert‐butyl cumyl peroxide (TBCP)/α‐methyl styrene (α‐MeS) were also used to prepare the TPVs for a comparison purpose. The TPVs with multifunctional peroxide, DTBT, provided good mechanical properties and phase morphology of small dispersed vulcanized rubber domains in the PP matrix which were comparable with the DCP/TAC cured TPVs. However, the TPVs with TBIB/α‐MeS and TBCP/α‐MeS showed comparatively low values of the tensile properties as well as rather large phase morphology. The results were interpreted by three main factors: the kinetic aspects of the various peroxides, solubility parameters of respective peroxide/coagent combinations in the ENR and PP phases, and the tendency to form unpleasantly smelling byproducts. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Effect of the compatibilizer,on the engineering properties of TPV based on Hypalon® and PP prepared by dynamic vulcanization

Elastomeric Chlorosulfonated polyethylene (Hypalon^®) and thermoplastic Polypropylene (PP) based thermoplastic vulcanizates (TPVs) were prepared in presence of different doses of compatibilizer, maleic anhydride grafted PP (PP‐g‐MA) by employing dynamic vulcanization technique. The effect of incorporation in different proportions of compatibilizer on mechanical, spectral, morphological, thermal, and rheological properties of such TPVs was studied and the same were compared to that of virgin PP and amongst themselves. The mechanical analysis of the prepared TPVs exhibited significant improvements in stress at 25% modulus, ultimate tensile strength (UTS), and hardness values. FTIR studies revealed that a chemical interaction had taken place between Hypalon^® and functionalized compatibilizer during the process of dynamic vulcanization which led to an enhancement of interfacial adhesion between them. The two‐phase morphologies were clearly observed by scanning electron microscopic studies. The T_g values of Hypalon^® was modified in the TPVs as exhibited by differential scanning calorimetric studies. TGA studies indicated the increase in thermal stability of all TPVs with respect to the elastomeric Hypalon^®. Rheological properties showed that the compatibilizer reduces the melt viscosity of TPVs and thus facilitates the processibility of such TPVs. © 2014 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 40312.     

Exploring the thermomechanical properties of peroxide/co-agent assisted thermoplastic vulcanizates through temperature scanning stress relaxation measurements

Temperature scanning stress relaxation (TSSR) measurement of peroxide vulcanized polymer blends of polypropylene (PP) and ultrahigh molecular-EPDM (UHM-EPDM) rubber has been performed to study the thermomechanical behavior of thermoplastic vulcanizates (TPVs). Co-agents play crucial roles in the enhancement of properties of TPVs. Different types of co-agents (Triallyl cyanurate-TAC; N, N-m-phenylene-dimaleimide-HVA2; zinc dimethacrylate-ZDMA; and in-situ formed zinc dimethacrylate-ZMA) have been explored in this work. TSSR study shows that higher T₅₀ and T₉₀ values have been achieved in ZMA co-agent assisted-TPV. Higher TSSR-index (RI) value was also found for the same co-agent ZMA, indicating higher elastic behavior. TSSR result supports the mechanical and rheological properties, and it is found that the ZMA and ZDMA show higher mechanical strength. Cross-linked-density calculated by modified Flory–Rehner equation and the cross-link-density as obtained from TSSR method have been compared and the trend was found to be the same. Stress relaxation study shows the slow relaxation-phenomena of the ZMA-TPV with slowest relaxation-time (θ_r) than the other TPVs, which correlates with superior material strength. Thermogravimetric analysis proves that there is a difference in degradation temperature of the blends at approximately 5–10°C. Ultrahigh molecular weight-EPDM/PP based TPVs reveal superior thermomechanical and physico-mechanical properties with ZMA and ZDMA co-agent over TAC and HVA2. These ultrahigh molecular weight-EPDM based TPVs can be used in automotive seals/strips, hoses, bellows, and 2 K-molds for automotive applications.     

Effect of the compatibility on the morphology and properties of acrylonitrile–butadiene rubber/polypropylene thermoplastic vulcanizates

In this study, the morphologies of three types of acrylonitrile–butadiene rubber (NBR)/polypropylene (PP) thermoplastic vulcanizates (TPVs) (with an NBR/PP blend ratio of 70/30) were compared. The TPVs were (1) an ultrafine fully vulcanized acrylonitrile–butadiene rubber (UFNBR)/PP TPV made by the mechanical blending of UFNBR with PP, (2) a dynamically vulcanized NBR/PP TPV without the compatibilization of maleic anhydride grafted polypropylene (MP) and amine‐terminated butadiene–acrylonitrile copolymer (ATBN), and (3) a dynamically vulcanized NBR/PP TPVs with the compatibilization of MP and ATBN. The influence of the compatibility therein on the size of the dispersed vulcanized NBR particles and the crystallization behavior of the PP in the TPVs and the resultant properties are also discussed. As indicated by Fourier transform infrared spectroscopy, scanning electron microscopy, differential scanning calorimetry, polarizing microscopy, dynamic mechanical thermal analysis, and rheological and mechanical testing, the compatibility was significantly improved by the reactive compatibilization of MP and ATBN, which led to a uniform and fine morphology. The compatibilization increased the crystallization rate and reduced the size of the spherulites of PP. On the other hand, it was found that the dispersed vulcanized NBR particles lowered the degree of crystallinity. The better the compatibility of the blend was, the lower the degree of crystallinity and the storage modulus were, but the higher the loss factor and the processing viscosity were. All TPVs showed almost the same oil resistance, but the TPV prepared with reactive compatibilization had the best mechanical properties. © 2011 Wiley Periodicals, Inc. J Appl Polym Sci, 2012     

Synergistic effect of SBS and trimethylopropane trimethacrylate (TMPTMA) on dynamically vulcanized SEBS/PP blends

The SEBS/PP thermoplastic vulcanizates (TPVs) were prepared by melt blending. Di‐tert‐butyl peroxide (DTBP) was used as the curing agent in combination with trimethylopropane trimethacrylate (TMPTMA) and poly(styrene‐b‐butadiene‐bstyrene) (SBS) as the coagents for the curing process. The synergistic effect of TMPTMA and SBS on the structure and properties of TPVs was studied by means of FT‐IR, DSC, torque rheometer, and universal testing machine. Both SEBS and PP crosslinked and the network structure formed under the participation of TMPTMA and SBS. Compared with the sole addition of the coagent, simultaneous loading of both TMPTMA and SBS could provide the TPVs with better solvent‐resistance and excellent mechanical properties. The crosslinking mechanism of the TPVs was also proposed. The slight lower value of T_m for the TPVs indicated the improved miscibility between PP and SEBS due to the crosslinking reaction. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44392.     

Influences of blend proportions and curing systems on dynamic,mechanical, and morphological properties of dynamically cured epoxidized natural rubber/high‐density polyethylene blends

Thermoplastic elastomers (TPEs) based on dynamically cured epoxidized natural rubber/high‐density polyethylene (ENR/HDPE) blends were prepared. Influence of the process oil, blend proportion, and curing systems were investigated. It was found that the oil‐extended thermoplastic vulcanizates (TPVs) exhibited better elastomeric properties and improved ease of the injection process. Increasing the proportion of ENR caused increasing elastic response of elongation at break, tension set properties, and tan δ. It was also found that the TPV treated with phenolic resin exhibited superior mechanical properties and the smallest vulcanized rubber domains. The TPV treated with the conventional peroxide co‐agent curing system showed superior strength properties but had poor elastomeric properties. POLYM. ENG. SCI., 2009. © 2008 Society of Plastics Engineers     

The effect of selective location of carbon nanotubes on electrical properties of thermoplastic vulcanizates

Three types of conductive thermoplastic vulcanizates (TPVs) were prepared by blending polypropylene (PP), carbon nanotubes (CNT), and carboxylic acrylonitrile butadiene ultrafine full‐vulcanized powdered rubber (xNBR‐UFPR). The CNT locations were different in these three types of TPVs, i.e., CNTs were localized in PP matrix, in the xNBR‐UFPR phase, or mainly in the interface. It had been found that TPV with CNTs localized mainly in the interface had the lowest conductive percolation threshold among these three types of TPVs. The volume resistivity of the TPV with 2 phr CNTs was as small as 220 Ω?cm. Moreover, the conductive TPV possessed good mechanical properties. © 2012 Wiley Periodicals, Inc. J. Appl. Polym. Sci., 2013     

Thermoplastic elastomers based on high‐density polyethylene,ethylene–propylene–diene terpolymer,and ground tire rubber dynamically vulcanized with dicumyl peroxide

Thermoplastic vulcanizates (TPVs) based on high‐density polyethylene (HDPE), ethylene–propylene–diene terpolymer (EPDM), and ground tire rubber (GTR) were dynamically vulcanized with dicumyl peroxide (DCP). The polymer blend was composed of 40% HDPE, 30% EPDM, and 30% GTR, and the concentration of DCP was varied from 0.3 to 3.6 parts per hundred rubber (phr). The properties of the TPVs were determined by evaluation of the gel fraction content and the mechanical properties. In addition, IR spectroscopy and differential scanning calorimetry analysis were performed as a function of the DCP content. Decreases in the Young's modulus of the blends and the crystallinity of HDPE were observed when the content of DCP was greater than 1.8 phr. The results regarding the gel content indicate that the presence of DCP promoted the crosslinking of the thermoplastic matrix, and optimal properties were obtained with 1.5% DCP. © 2013 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2014 , 131, 39901.     

1H-NMR imaging study of molecular mobility in carbon black-filled,TBBS–sulfur-vulcanized cis-polyisoprene

The distributions of the T₂ relaxation times in carbon black filled, TBBS-Sulfur vulcanized cis-polyisoprene were were studied using ¹H NMRI spin–echo experiments. It has been reported that more than two T₂ relaxation times are observed in carbon black-filled rubbers, reflecting the existence of the hard regions adjacent to the crosslinks or filler particle and soft regions distant from such rigid components. Our current concern is how the amount and distribution of the T₂ times are affected by the filler incorporation in the rubber compounds. A decrease in the T₂ relaxation times with an increasae in carbon black content is observed. The average T₂ time, 〈T₂〉, drops from 11.38 ms with no carbon black to 10.05 ms with 15 phr carbon black. The 〈T₂〉 further decreases when the black loading level is increased form 15 to 30 phr and 30 to 50 phr, but the magnitude of the changes in the 〈T₂〉s are not as large as in the initial loading (0 to 15 phr). The observations of the 〈T₂〉s suggest inhomogeneities are induced in the network structure by the black incorporation. The distribution of the T₂ relaxation times becomes narrower as the black loading level increases. There are at least four factors governing the intensity of the images in the swollen, filled rubber vulcanizates as well as the NMR parameters (T₁, T₂, T_R, and T_E: (1) ¹H spin density, (2) inhomogeneity of the network structure, (3) degree of swelling in the sampling solvent, and (4) displacement effect of the carbon black. © 1998 John Wiley & Sons, Inc. J. Appl. Polym. Sci. 70: 1385–1390, 1998     

Systematic investigation on the effect of crosslinking agent type and dosage on the performance of TPU/MVQ based thermoplastic vulcanizates

Dynamic vulcanized thermoplastic polyurethane (TPU)/methyl vinyl silicone rubber (MVQ) thermoplastic vulcanizates (TPVs) were prepared in torque rheometer. The influence of the type and amount of peroxide crosslinking agent on the mechanical properties, thermal stability, micromorphology and melt flowability was systematically investigated. The results showed that the mechanical properties of the TPVs vulcanized by 2,5-dimethyl-2,5-di (tert-butyl peroxy) hexane (DBPH) first increased and then decreased with increasing the peroxide amount, while for dicumyl peroxide (DCP) vulcanizing system the mechanical properties slowly increased. Besides, the comprehensive mechanical properties vulcanized by DBPH were better than those of DCP group. The results of the thermogravimetric analysis showed that the TPVs vulcanized by DBPH had better heat stability, corresponding to the excellent thermo-oxidative aging performance and the 38% increase in tensile strength after aging. In addition, the MVQ rubber particles showed better dispersing performance for DBPH vulcanizing system. The melt flow rate of the TPVs showed a linear relationship with increasing DBPH dosage and became worse after the amount of crosslinking agent exceeded 1.5 phr. By comprehensive comparison, the TPVs have better performance when use peroxide DBPH as the crosslinking agent and the dosage is 1.5 phr.     

Effect of grafted maleic anhydride content and recyclability of dynamically cured maleated natural rubber/polypropylene blends

Maleated natural rubbers (MNRs) were prepared using various levels of maleic anhydride (MA) at 4, 6, 8, 10, and 12 phr. Dynamically cured 60/40 MNR/PP blends with phenolic‐modified polypropylene (Ph‐PP) compatibilizer at a loading level of 5 wt % of PP were prepared by melt mixing process using sulfur vulcanization system. The influence of the level of MA on properties of the thermoplastic vulcanizates (TPVs) was studied. It was found that the mixing torque, apparent shear stress, shear viscosity, tensile strength, and hardness properties increased with increasing levels of the MA or grafted succinic anhydride groups in the MNR molecules. This is attributed to an increase in chemical interaction and reaction between methylol groups in the Ph‐PP molecules and polar functional groups in the MNR molecules upon increasing levels of the grafted succinic anhydride groups. As a consequence, compatibilizing block copolymers of MNR and PP blocks were formed. The block copolymers were capable of compatibilizing with MNR and PP blend components via the respective blocks. Recyclability of the MNR/PP TPVs was also studied. It was found that, after processing through a number of cycles by injection molding and extrusion processing, the TPV exhibited marginal decreases in mechanical properties. This corresponded to slightly increasing size of the dispersed vulcanized rubber domains. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008     

Preparation,characterization, and property testing of condensation‐type silicone/montmorillonite nanocomposites

Nanocomposites (NCs) of silicone rubber and organically modified montmorillonite (OMMT) nanoparticles were prepared and characterized. It was shown that OMMT loadings of 2 and 3.5 parts per hundred resin/filler per weight (phr) produced exfoliation or delamination hybrids, whereas at a concentration of 5 phr, the filler seemed to retain its original crystallographic morphology, and the system shifted to an ordinary reinforced elastomer. Fourier transform infrared analysis, differential scanning calorimetry, and thermogravimetric analysis testing were performed for characterization and showed no effect of the nanofiller on the structural parameters of the composites, with the exception of a reduction in the crystallinity. Dynamic mechanical analysis revealed an increase in the glass‐transition temperature (T_g) at OMMT concentrations of 2 and 3.5 phr, whereas at 5 phr, T_g dropped again. Finally, mechanical testing showed an improvement in the tensile strength and stiffness, whereas improved solvent resistance was recorded by swelling experiments in toluene. This experimental study allowed us to explore the range where the OMMT filler produced NCs with silicone elastomers and, furthermore, showed that the incorporation of OMMT into silicone rubber did not introduce any chemical changes but increased the density of crosslinks; this led to a loss of crystallinity, an increase in T_g, and a significant improvement in the tensile properties. © 2010 Wiley Periodicals, Inc. J Appl Polym Sci, 2010     

The Effect of Dicumyl Peroxide Vulcanization on the Properties & Morphology of Polypropylene/Ethylene-Propylene Diene Terpolymer/Natural Rubber Blends

ABSTRACT

This article discusses some properties such as tensile properties, chemical and oil resistance, gel content, crystallinity, and morphology of polypropylene (PP)/ethylene-propylene diene terpolymer (EPDM)/natural rubber (NR) blends. Dicumyl peroxide (DCP) was applied as a crosslinking agent. In terms of tensile properties, peroxide vulcanized blend shows higher tensile strength and tensile modulus (stress at 100% elongation, M₁₀₀) as compared with the unvulcanized blend. The elongation at break of the peroxide vulcanized blend is higher for the blend with NR rich content compared with the EPDM rich content. The improvements in chemical and oil resistance as well as gel content of peroxide vulcanized blends have also proved the formation of crosslinks in the rubber phase. Scanning electron microscopy (SEM) micrographs from the surface extraction of the blends support that the crosslinks have occurred during dynamic vulcanization. Dynamical vulcanization with DCP has decreased the percent crystallinity of blends that can be attributed to the formation of crosslinks in the rubber.     

Regulation of trans‐1,4‐polyisoprene crystallinity and mechanical properties of styrene‐butadiene rubber/trans‐1,4‐polyisoprene vulcanizate

The effects of processing temperature and bis‐[γ‐(triethoxysilyl)‐propyl]‐tetrasulfide (Si69) on crystallization, morphology, and mechanical properties of styrene‐butadiene rubber (SBR)/trans‐1,4‐polyisoprene (TPI) vulcanizate are investigated. The crystallinity and crystalline melting temperature (T_m) of TPI in the vulcanizates with TPI/silica/(Si69) pre‐mixed at 150 °C are much lower than that pre‐mixed at 80 °C. At the same pre‐mixing temperature, the presence of 1 phr Si69 leads to a decreased crystallinity and T_m. The TPI domains with phase size of about 1 μm and silica are well dispersed in the vulcanizate, and TPI crystals get smaller in size and less in amount by pre‐mixing TPI, silica and Si69 at 150 °C. The vulcanizates with TPI/silica/(Si69) pre‐mixed at 150 °C have decreased tensile strength and modulus at a given extension than that pre‐mixed at 80 °C. At the same pre‐mixing temperature, the tensile strength and modulus of the vulcanizate increase with the addition of 1 phr Si69. The crystallinity of TPI component in SBR/TPI vulcanizate is effectively controlled by changing processing temperature and adding Si69, which is important for theoretical research and practical application of TPI. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017 , 134, 44395.     

Development of hydroxyapatite nanoparticles reinforced chlorinated acrylonitrile butadiene rubber/chlorinated ethylene propylene diene monomer rubber blends

Hydroxyapatite nanoparticles (HA) reinforced polymer blend based on chlorinated nitrile rubber (Cl-NBR) and chlorinated ethylene propylene diene monomer rubber (Cl-EPDM) were prepared. Resulting blend composites were analyzed with regard to their rheometric processing, crystallinity, glass transition temperature (T_g), mechanical properties, oil resistance, AC conductivity, and transport behavior. The decrease in optimum cure time with the addition of HA is more advantageous for the development of products from these blend nanocomposites. The XRD, FTIR, and SEM confirmed the attachment and uniform dispersion of HA nanoparticles in the Cl-NBR/Cl-EPDM blend. The good compatibility between polymer blend and nanoparticles was also deduced by the formation of spherically shaped HA particles in the blend matrix determined by TEM analysis. DSC analysis showed an increase in T_g of the blend with the filler loading. The addition of HA particles to the blend produced a remarkable increase in tensile and tear strength, hardness, AC conductivity, abrasion, and oil resistance. The diffusion of blend composites was decreased with an increase in penetrant size. The diffusion mechanism was found to follow an anomalous trend. Among the blend composites, the sample with 7 phr of HA not only showed good oil and solvent resistance but also a remarkable increase in AC conductivity and mechanical properties.     

Influence of phenolic curative on crosslink density and other related properties of dynamically cured NR/HDPE blends

Dynamically cured 60/40 NR/HDPE blends with various amounts of phenolic curative were prepared in an internal mixer at 160°C. A simple blend (i.e., the blend without curative) was also prepared using the same materials and blend proportion for comparison purposes. Mechanical, dynamic, and morphological properties; swelling resistance and crosslink density of the blends were investigated. It was found that the thermoplastic vulcanizates (TPVs) gave superior mechanical and dynamic properties than the simple blend. Furthermore, the mechanical properties in terms of elongation at break, modulus and tensile strength and elastic response in dynamic test in terms of storage modulus increased with increased loading amount of the curative. The complex viscosity also increased but the tan δ and tension set decreased with increased loading level of the curative. The crosslink density of the TPVs was estimated based on the elastic shear modulus. It was found that the crosslink density of the blends increased with increased loading levels of the curative while the degree of swelling decreased. This correlated well with the trend of mechanical and dynamic properties. SEM micrographs were used to confirm the level of mechanical and dynamic properties. It was found that the simple blend at a given blend ratio exhibited co‐continuous phase morphology. However, the TPVs showed micron scale of vulcanized rubber domains dispersed in a continuous HDPE matrix. The size of vulcanized rubber domains decreased with increasing amounts of the curative. This led to greater interfacial adhesion between the phase and hence superior mechanical and dynamic properties. © 2009 Wiley Periodicals, Inc. J Appl Polym Sci, 2009     

Melt fracture and wall slip of thermoplastic vulcanizates

Thermoplastic vulcanizates (TPVs) are blends of polypropylene (PP) (thermoplastic phase) and ethylene propylene diene monomer (EPDM) rubber (rubber phase) in which a high content of rubber EPDM is cross-linked and dispersed in a thermoplastic matrix (PP) in the presence of oil (lubricant) and filler. Depending on the molecular characteristics of the constituent polymers, the level of curing and the amount of cross-linked rubber, their processing (extrusion) exhibits various difficulties such as melt fracture (extrudate distortions). In this study, a number of different TPVs with various characteristics, including the degree of curing and amount of cross-linked rubber are examined in capillary extrusion at two different temperatures (190°C and 205°C) relevant to real processing. First, the effect of the temperature on the yield stress is investigated using rheological measurements. Consequently, the flow behavior of the TPVs in capillary flow is studied concluding that TPVs slip massively (nearly plug flow) due to the presence of lubricant and the vulcanized rubber phase. Although there is little slip observed in PP samples, EPDMs themselves exhibit severe slip and melt fracture. As a consequence, the TPV samples essentially follow the slip behavior of EPDMs. Finally, the melt fracture analysis of several TPVs has shown that with increase of temperature and amount of cross-linked rubber, the severity of TPVs' surface defects increases accordingly.     

Short polyethylene terephthalate fiber (PET) reinforced NBR rubber composites

Acrylonitrile-butadiene rubber (NBR) has been reinforced with different content of PET up to 25 phr. Vulcanization of prepared composites as will as the unreinforced ones have been induced by ionizing radiation of accelerated electron beam of varying dose up to 150 kGy. Evaluations of the vulcanized composites have been followed up through the measurement of mechanical, physical and thermal properties. Also, scanning electron microscope (SEM) was performed. Mechanical properties, namely tensile strength (TS) and hardness were found to increase with the increase of irradiation dose as well as the increase in the content of PET up to 25 phr. Also, elongation at break (ε _b) was found to decrease with the increase of irradiation dose; however, the decrease in ε_b is not consistence with the increase in fibers loading. Young’s modulus (E) and tensile modulus at 25% elongation (E25) were found to increase with the increase of irradiation dose and fiber loading up to 20 phr. Also, the volume fraction of swollen rubber increases as irradiation dose and/or fiber content increased; it was more influenced by irradiation rather than fiber loading. Anisotropic swelling increased with irradiation and fiber loading up to 20 phr. SEM photomicrograph showed that irradiation causes adhesion between PET fiber and NBR where less pulling out and less pitting on the surface were observed. The thermal properties of the composite irradiated at 100 kGy reveal that the activation energy (E _a) increases up to 10 phr fiber content. When the composite that contains 10 phr fiber irradiated at doses higher than100 kGy, Ea decreased.     

Thermoplastic vulcanizates based on poly(methyl methacrylate)/epoxidized natural rubber blends: Mechanical,thermal, and morphological properties

Epoxidized natural rubbers (ENRs) with epoxide levels of 10, 20, 30, 40 and 50 mol % were prepared. The ENRs were later used to prepare thermoplastic vulcanizates (TPVs) by blending them with poly(methyl methacrylate) (PMMA) using various formulations. Dynamic vulcanization, using sulfur as a vulcanizing agent, was performed during the mixing process. The mixing torque increased as the ENR contents and epoxide molar percentage increased. This was because of an increasing chemical interaction between the polar groups of the blend components, particularly at the interface between the elastomeric and thermoplastic phases. The ultimate tensile strength of the TPVs with ENR‐20 was high because of strain‐induced crystallization. ENRs with epoxide levels >30 mol % exhibited an increase of tensile strength because of increasing levels of chemical interaction between the molecules and the different phases. The hardness of the TPVs also increased with increased epoxide levels but decreased with increased contents of ENRs. Two morphology phases with small domains of vulcanized ENR particles dispersed in the PMMA matrix were observed from scanning electron microscopy micrographs. The TPVs based on ENR‐20 and ENR‐50 showed smaller dispersed rubber domains than those of the other types of ENRs. Furthermore, the size of the vulcanized rubber domain decreased with increasing amounts of PMMA in the blends. The decomposition temperature of the TPVs also increased as both the levels of ENRs in the blends and the epoxide molar percentage increased. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 1251–1261, 2005