Emission Analysis of Pr3 +& Tm3 +: B2O3-BaO-LiF/AlF3 Glasses

We report here on the preparation and emission properties of Pr³⁺(4f²) and Tm³⁺ (4f¹²) ions doped in newly developed to transparent glassy matrices of BBLi (= B₂O₃-BaO-LiF) BBAl (= B₂O₃-BaO-AlF₃). Under an UV source (355 nm), both the Tm³⁺: BBLi and Tm^{3 +}: BBAl glasses have shown bright blue emission at 452 nm. With regard to both the Pr³⁺: BBL and Pr³⁺: BBAl glasses red emission have been noticed upon excitation with blue excitation wavelength (445 nm).These results have also been obtained from the measurement of their emission spectra. For such emission bands, decay curves have been recorded to obtain their lifetimes. We have prepared optical glasses with good transparency and stability. From the measurement of XRD spectra, amorphous nature of these glasses have been confirmed. Between the two glasses studied, glass containing Li has demonstrated an extended UV transmission and also it has revealed an improved NIR transmission ability compared to the other glass with LiF.     

机械振动辅助Bi2O3-ZnO-B2O3三元玻璃料浆均匀化机理

通过数值模拟研究了机械振动下Bi₂O₃-ZnO-B₂O₃三元玻璃料浆的混合过程，并分析了混合均匀化机理。首先，利用旋转黏度计分别测量了Bi₂O₃、ZnO及B₂O₃三种玻璃料浆的黏度，并用光学显微镜分别观察三种玻璃料浆的粒度，通过Stokes-Einstein方程得到流体料浆的扩散系数。在此基础上建立了机械振动下Bi₂O₃-ZnO-B₂O₃三元玻璃料浆混合过程的Fluent模型，定义了描述三元料浆混合均匀程度的混合偏差。通过模拟研究发现：①增加容器振幅及频率均能加快三元料浆的混合；②机械振动的振幅及频率不宜过高，否则会导致料浆溢出容器；③混合偏差随时间增加而降低，可以通过幂函数描述，从而可以预测不同振幅和频率下Bi₂O₃-ZnO-B₂O₃三元玻璃料浆的混合均化时间。指出选择合适的振幅及频率，有助于提高混合效率，并避免料浆溢出容器。     

Co3O4-Bi2O2CO3催化剂的制备及其光催化性能

以Bi(NO₃)₃·5H₂O、Co(CH₃COO)₂·4H₂O为原料,采用化学沉淀-水热法制备了Co₃O₄-Bi₂O₂CO₃异质结构复合半导体光催化剂,并通过X射线衍射仪（XRD）、扫描电镜（SEM）、X射线光电子能谱（XPS）、紫外可见漫反射光谱（DRS）、荧光光谱（PL）等手段对所合成的复合型催化剂进行了理化性能表征。研究结果表明：引入Co₃O₄没有改变Bi₂O₂CO₃物相结构,但促进了Bi₂O₂CO₃ 对可见光的吸收能力,提高了Bi₂O₂CO₃表面吸附氧物种的数量,抑制了光生载流子复合。复合光催化剂对罗丹明B（RhB）的光催化脱色实验显示引入Co₃O₄能够明显提高Bi₂O₂CO₃催化剂的光催化脱色能力。尤其是Co₃O₄引入量为0.6%的Co₃O₄-Bi₂O₂CO₃样品对罗丹明B染料的光催化脱色率可达到97%（模拟日光照射30min）。本文为复合型光催化剂制备提供了简单易行的技术路线,制备的新型半导体复合光催化剂Co₃O₄-Bi₂O₂CO₃在环境净化方面表现出了较好的应用前景。     

Na2O-Al2O3-SiO2-P2O5玻璃的结构和析晶性能研究

采用熔融-淬冷法制备了不同(Al₂O₃+P₂O₅)含量的碱铝硅酸盐玻璃,通过拉曼光谱、X射线衍射光谱、扫描电镜研究了其结构特征和析晶性能。发现随着(Al₂O₃+P₂O₅)含量减少,玻璃中Na₂O含量增加,玻璃化转变温度从685 ℃降低到622 ℃,当减少至摩尔分数为22%时,出现析晶峰且起始析晶温度降低。拉曼光谱表明Q⁴_P对应的拉曼峰强度变低且逐渐向低波数方向移动,说明Na₂O作为网络修饰体使硅酸盐玻璃结构逐步解聚,玻璃的析晶能力逐渐增强。结果表明:当(Al₂O₃+P₂O₅)摩尔分数为22%时热处理后的样品存在晶型转变,700 ℃热处理时以NaAlSiO₄霞石晶体为主,900 ℃时转变为以Na_6.8Al_6.3Si_9.7O₃₂霞石晶体为主。当(Al₂O₃+P₂O₅)的摩尔分数为21%和20%时,热处理后的样品能稳定析出Na₃PO₄和Na_6.8Al_6.3Si_9.7O₃₂晶体。热处理后的样品析出了耐酸侵蚀性较差的富磷相和Na₃PO₄晶体,导致化学稳定性变差。     

Photocatalytic activity of Cu2O/TiO2, Bi2O3/TiO2 and ZnMn2O4/TiO2 heterojunctions

Cu₂O/TiO₂, Bi₂O₃/TiO₂ and ZnMn₂O₄/TiO₂ heterojunctions were studied for potential applications in water decontamination technology and their capacity to induce an oxidation process under VIS light. UV–vis spectroscopy analysis showed that the junctions-based Cu₂O, Bi₂O₃ and ZnMn₂O₄ are able to absorb a large part of visible light (respectively, up to 650, 460 and 1000 nm). This fact was confirmed in the case of Cu₂O/TiO₂ and Bi₂O₃/TiO₂ by photocatalytic experiments performed under visible light. A part of the charge recombination that can take place when both semiconductors are excited was observed when a photocatalytic experiment was performed under UV–vis illumination. Orange II, 4-hydroxybenzoic and benzamide were used as pollutants in the experiment. Photoactivity of the junctions was found to be strongly dependent on the substrate. The different phenomena that were observed in each case are discussed.     

混合碱效应对Li2O-Al2O3-SiO2系玻璃结构和热膨胀性能的影响

本文用传统高温熔融法熔制Li₂O-Al₂O₃-SiO₂系高铝玻璃,改变碱金属氧化物n(Li₂O)/n(Na₂O)的摩尔比,运用阿基米德排水法、热膨胀仪、DSC、傅里叶变换红外光谱和拉曼光谱等测试手段和仪器,探究了混合碱金属效应对Li₂O-Al₂O₃-SiO₂系玻璃结构和热膨胀性能的影响。结果显示:随着n(Li₂O)/n(Na₂O)比例增大,混合碱金属效应对Li₂O-Al₂O₃-SiO₂系玻璃的密度和热膨胀系数的影响一致,表现为先增大后减小,当R=0.25(R=n(Li₂O)/[n(Li₂O)+n(Na₂O)],摩尔比)时,出现极值,此时密度达到最大2.447 4 g/cm³,热膨胀系数达到最大7.811 7×10^-6/℃;对玻璃特征温度的影响随着温度的升高而逐渐减弱至消失;对玻璃的析晶能力有一定的提升作用;对玻璃三维骨架结构中的硅氧四面体Qⁿ的影响也各不相同。     

Facile ultrasonic-assisted synthesis of micro–nanosheet structure Bi4Ti3O12/g-C3N4 composites with enhanced photocatalytic activity on organic pollutants

The Bi₄Ti₃O₁₂/g-C₃N₄ composites with microsheet and nanosheet structure were prepared through facile ultrasonic-assisted method. The SEM and TEM results suggested that the nanosheets g-C₃N₄ were stacked on the surface of regular Bi₄Ti₃O₁₂ sheets. Comparing with pure Bi₄Ti₃O₁₂ and g-C₃N₄, the Bi₄Ti₃O₁₂/g-C₃N₄ composites showed significant enhancement in photocatalytic efficiency for the degradation of RhB in solution. With the mass ratio of g-C₃N₄ increasing to 10 wt%, the Bi₄Ti₃O₁₂/g-C₃N₄-10% presented the best photocatalytic activity. Its photocatalysis reaction constant was approximately 2 times higher than the single component Bi₄Ti₃O₁₂ or g-C₃N₄. Meanwhile, good stability and durability for the Bi₄Ti₃O₁₂/g-C₃N₄-10% were confirmed by the recycling experiment and FT-IR analysis. The possible mechanism for the improvements was the matched band positions and the effective separation of photo-excited electrons (e^-) and holes (h⁺). Furthermore, based on the results of active species trapping, photo-generated holes (h⁺) and superoxide radical (·O₂^-) could be the main radicals in reaction.     

Nb2O5对Nd3+掺杂锗酸盐玻璃光谱性能的影响

蓝光激光器在彩色激光显示、高密度光储存、海洋资源探测、水下通信以及生物科技等领域具有广泛的应用前景。目前较为成熟的Yb³⁺掺杂光纤激光器倍频后仅能获得~490 nm蓝绿光,因此如何得到接近450 nm的纯蓝光激光器是目前急需解决的问题。Nd³⁺:⁴F_3/2→⁴I_9/2能级跃迁产生的0.9 μm光经倍频后可获得~450 nm光,并可应用于蓝光激光器,但该跃迁产生的光所占荧光分支比较低。本文系统研究了1%(质量分数)Nd₂O₃掺杂50GeO₂-(20-x)PbO-15BaO-15ZnO-xNb₂O₅(x%=0%,2.5%,5%,10%,15%,摩尔分数)玻璃的吸收光谱、荧光光谱和荧光寿命,计算了相应的Judd-Ofelt强度参数以及增益带宽。研究发现,Nb₂O₅的加入会使Nd³⁺在900 nm荧光峰的吸收截面、发射截面、有效线宽和荧光分支比增加。当Nb₂O₅浓度为10%(摩尔分数)时,Judd-Ofelt强度参数Ω₂=5.91×10^-20 cm²,光谱质量参数χ=1.01,荧光分支比为42.9%。综上所述,Nb₂O₅能提高Nd³⁺ 0.9 μm的荧光分支比,从而倍频获得纯蓝光(450 nm),有利于蓝光激光器的发展及应用。     

撞击流反应器制备纳米四氧化三铁的研究

在浸没式循环撞击流反应器中,以氨水为沉淀剂,用七水合硫酸亚铁和六水合三氯化铁为原料,采用共沉淀法制备了纳米四氧化三铁粒子。考察了搅拌转速、亚铁与三价铁物质的量比、反应温度和溶液pH对所得纳米四氧化三铁的分散性和粒径的影响。采用傅里叶红外光谱仪、透射电镜、X射线衍射仪等对制得的纳米粒子的结构和性能进行了表征。结果表明：用撞击流反应器制备纳米四氧化三铁粒子的最佳工艺条件：亚铁与三价铁物质的量比为1 ∶1,反应温度为40 ℃,搅拌转速为1 600 r/min,以氨水作沉淀剂,最佳pH控制在11.0左右。在上述条件下,可以制备出分散性好、纯度高、平均粒径为10 nm的四氧化三铁粒子。     

A/B位离子掺杂BiFeO3纳米薄膜的微结构与铁电性能

采用化学溶液法结合层层旋涂退火工艺,在掺氟氧化锡导电玻璃基片上制备了BiFe_0.95Mn_0.05O₃和Bi_0.9Nd_0.1FeO₃纳米晶铁电薄膜,并分析比较了其微结构和铁电性能。结果表明:2组分样品均为单相多晶钙钛矿结构,晶粒细小均匀,表面平整,结构致密。两薄膜均获得了饱和电滞回线,且BiFe_0.95Mn_0.05O₃薄膜具有向上的择优取向极化和更优异的铁电性能,其剩余极化强度(Pr)达60mC·cm^–2,在1~50 k Hz频率范围与25~200℃温度区间内铁电极化响应稳定,保持时间长达1′10³ s工作与反复极化翻转高达1′10⁹次表现出优异的电荷保持力和抗疲劳稳定性。     

Bi2O2CO3/Fe3O4磁性复合物在环境污染治理领域中的应用

以Fe₃O₄纳米粒子和Bi₂O₂CO₃为原料,采用溶剂热法制备Bi₂O₂CO₃/Fe₃O₄磁性复合物,并通过对印染废水中染料的去除、剩余污泥厌氧消化过程中产甲烷潜力的影响两方面探讨其在环境污染治理中的应用。借助X射线衍射（XRD）、扫描电镜（SEM）、傅里叶红外光谱（FTIR）和比表面积及孔径分析对Bi₂O₂CO₃/Fe₃O₄复合物进行表征分析,SEM分析结果表明复合物表面较粗糙,BET结果显示复合物的比表面积为9.2294m²/g,Fe₃O₄的引入大幅度增加了Bi₂O₂CO₃的比表面积,使其具有明显的介孔结构。一方面,以甲基橙（MO）为目标污染物,研究了不同实验条件下该材料对染料的去除效果,结果表明,最大吸附量可达14.373mg/g,且该吸附反应过程符合拟二级动力学和Langmuir吸附等温模型,趋于单分子层吸附;另一方面,评估了复合物对污泥厌氧消化产甲烷潜力的影响,结果表明,复合物的引入对污泥厌氧消化产甲烷过程有一定的促进作用,累积产甲烷量相比于对照组提高了10%。分别用一级动力学模型和修正Gompertz模型模拟厌氧消化过程,模拟结果显示一级动力学模型可以更好地描述引入Bi₂O₂CO₃/Fe₃O₄磁性复合物的污泥厌氧消化过程。     

Mechanism of the Blue Up-Conversion in Tm3+/Nd3+-doped Calcium Aluminate Glasses

Blue up-conversion fluorescence from the Tm³⁺:¹ G ₄→³ H ₆ (480 nm) transition has been observed from calcium aluminate glass codoped with Tm³⁺/Nd³⁺. The mechanism for the up-conversion process consists of a two-photon process. An excitation beam with a wavelength of 791 nm first excites Tm³⁺ to the ³ H ₄ level, where Tm³⁺ again absorbs the 1060 nm emission from Nd³⁺:⁴ F _3/2→⁴ I _11/2 to attain the Tm³⁺:¹G₄ level. Lifetime and intensity variations with compositions suggest the presence of an efficient energy transfer from Nd³⁺ to Tm³⁺. The highest 480 nm emission intensity has been obtained from the glass with 0.1 mol% of Nd₂O₃ and 0.2 mol% of Tm₂O₃.     

纳米γ-氧化铁的制备及其吸附性能研究

以硝酸铁和十二烷基三甲基溴化铵为原料,采用固相法制备了γ-氧化铁纳米粒子。通过X射线衍射、氮气吸附-脱附、磁性测试等手段对γ-氧化铁样品进行了表征。研究了γ-氧化铁对有机染料直接耐酸大红4BS的吸附性能。结果表明,制备的γ-氧化铁样品为γ-氧化铁纳米粒子,平均晶粒尺寸为18.5 nm;γ-氧化铁的比表面积为83.2 m ²/g,孔容为0.25 cm ³/g,最可几孔径为3.8 nm,属于介孔范围;γ-氧化铁的最大饱和磁化强度为63.7 A·m ²/kg;介孔γ-氧化铁对直接耐酸大红4BS的吸附过程符合准二级吸附动力学模型;γ-氧化铁对直接耐酸大红4BS的吸附符合Langmuir吸附等温式,极限吸附量为113.3 mg/g;将γ-氧化铁脱附处理后可重复使用。     

Al2O3含量对PbO-CaO-B2O3-SiO2系玻璃析晶行为与烧结性能的影响

PbO-CaO-B₂O₃-SiO₂系玻璃粉体是耐高过载低温共烧陶瓷(LTCC)生瓷带的主要组成部分。玻璃粉体的析晶行为影响烧结性能,进而决定基板的使用性能。本文研究了Al₂O₃含量对PbO-CaO-B₂O₃-SiO₂系玻璃析晶行为与烧结性能的影响。结果表明:向PbO-CaO-B₂O₃-SiO₂系玻璃中引入Al₂O₃可抑制玻璃析晶,防止高膨胀晶相的析出,并提高玻璃烧结密度;不含Al₂O₃的PbO-CaO-B₂O₃-SiO₂玻璃粉体析晶峰温度为862 ℃,烧结过程中析出方石英晶相,20~200 ℃的平均线膨胀系数高达260.8×10^-7 ℃^-1;引入2.1%(质量分数)Al₂O₃可显著抑制玻璃析晶,700 ℃烧结后膨胀系数降低至72.9×10^-7 ℃^-1,介电常数显著增大,由6.30提高至7.02。     

A low frequency Raman study of SrBi2Ta2O9-Bi3TiNbO9

Raman spectra of SrBi₂Ta₂O₉ (SBT), Bi₃TiNbO₉(BTN), and x(SBT) + (1-x)(BTN) samples were studied for the first time in the low frequency region. The BTN spectra show two features around 33 and 41 cm^-1, while only one feature, around 30 cm^-1, is found in SBT. The stoichiometric evolution of the Raman spectra shows that the frequency positions of these bands decrease as x changes from 0 to 1. Strong correlation is found between the frequency positions of these modes and both the Curie temperature and the a-parameter. The results are interpreted in terms of the ferroelectric displacive modes, which are responsible for the strong spontaneous polarization along a-axis. The band around 65 cm^-1is assigned to oxygen motion in the B₂O₂ layer.     

高稳定性SrF2-Na2O-Fe2O3-P2O5体系氟磷酸盐玻璃的制备与表征

⁹⁰SrF₂和高Na₂O、Fe₂O₃、P₂O₅含量的废物是两大类核电废物,将两者联合固化可获得以SrF₂、Na₂O、Fe₂O₃和P₂O₅为主要组成的玻璃固化体。本文采用X-射线荧光光谱仪、X-射线衍射仪、红外光谱仪、热膨胀仪、差热分析仪等研究了各样品的玻璃形成能力、实际组成、结构及热稳定性;采用溶解速率法和产品一致性测试方法研究了样品的耐水性。结果表明:1 000 ℃熔融保温0.5 h制得的玻璃中Sr损失较小而F质量损失达30%~34%;随着P₂O₅/SrF₂摩尔比的降低,玻璃的热稳定性急剧降低,而耐水性却有明显的改善;具有焦磷酸盐玻璃结构的样品稳定性好,其中SrF₂为30%(摩尔分数)的玻璃既具有高耐水性又具有较高的热稳定性。     

四元体系（Li+， Mg2+//Cl-， borate-H2O）308.15 K相平衡与相图研究

采用等温溶解平衡法,开展四元体系Li⁺, Mg²⁺//Cl^-, borate–H₂O固液相平衡与相图研究,测定平衡溶液的液相组成、密度、折射率和pH。该四元体系相图中存在的盐类矿物为：LiCl·H₂O、Li₂B₄O₇·3H₂O、 MgCl₂·6H₂O、Mg₂B₆O₁₁·15H₂O和锂光卤石LiCl·MgCl₂·7H₂O,其中锂光卤石LiCl·MgCl₂·7H₂O是异成分复盐,溶液中MgCl₂存在下章氏硼镁石（MgB₄O₇·9H₂O）不稳定,转化为多水硼镁石（Mg₂B₆O₁₁·15H₂O）。多水硼镁石结晶区最大,表明镁硼酸盐易于结晶析出,而锂光卤石结晶区最小。采用Pitzer热力学模型对该四元体系的溶解度进行理论预测,计算相图与实验相图吻合较好。该四元体系的稳定相平衡与相图研究,可为含锂硼盐湖老卤中锂、镁、硼产品开发及其综合利用提供理论依据。     

Co2+掺杂ZnO-MgO-Al2O3-SiO2系微晶玻璃的制备及光学性能

本文采用熔融法和热处理制备了Co²⁺掺杂的ZnO-MgO-Al₂O₃-SiO₂(ZMAS)系透明微晶玻璃,基于X射线衍射的结果确定了微晶玻璃的主要晶相为ZnAl₂O₄/MgAl₂O₄,并且随着晶化处理时间的增加,微晶玻璃的物相构成没有发生明显变化,尖晶石相的结晶度和平均晶粒尺寸呈现先增大后减小的趋势。吸收光谱和发射光谱的结果表明Co²⁺进入了尖晶石相ZnAl₂O₄/MgAl₂O₄中,并取代了四面体位置(T_d)的Zn²⁺或Mg²⁺。随着晶化处理时间的增加,样品的吸收光谱强度和发射光谱强度均呈现先升高后降低的趋势,这与X射线衍射结果的变化趋势一致,说明可以通过控制微晶玻璃的结晶度来调控光学性能,这对制备性能优良的微晶玻璃材料具有一定的指导意义。对比了采用不同价态Co的氧化物原料制备的微晶玻璃,结果表明无论是掺杂CoO还是Co₂O₃,微晶玻璃尖晶石相中的Co元素均以Co²⁺形式存在。此外,将所制备的微晶玻璃材料在1 540 nm处的基态吸收截面(σ_gas)同Co掺杂的其他基体材料进行了对比,发现它有望作为可饱和吸收体应用于调Q激光器中。     

Electrical properties of (Bi2O3)0.75(RE2O3)0.25 ceramics (RE=Dy, Y, Ho, Er and Yb)

Five kinds of rare earth stabilized bismuth oxide ceramics, (Bi₂O₃)_0.75(RE₂O₃)_0.25 (RE=Dy, Y, Ho, Er and Yb), were synthesized by sintering a mixture of Bi₂O₃ and RE₂O₃ at 900–1100 °C and their electrical properties were investigated. The bulk density and the lattice constant linearly increased with an increase in the atomic weight of RE and the ionic radius of RE³⁺, respectively. The electrical conductivity at 300 °C slightly increased with the increasing ionic radius of RE³⁺, while at 500 and 700 °C, it was constant regardless of the ionic radius of RE³⁺. The migration activation energy and the association activation energy showed a maximum value and a minimum value at RE=Er, respectively.     

Strong Green and Red Upconversion Emission in Er3+-Doped Na1/2Bi1/2TiO3 Ceramics

Upconversion emission properties of Na_1/2Bi_1/2TiO₃:Er³⁺ ceramics prepared by the solid-state reaction method were analyzed as a function of Er³⁺ concentration and incident pump power. Strong green (550 nm) and red (670 nm) emission bands were observed with 980 nm excitation at room temperature. Experimental results showed that the emission bands can be tuned by changing Er³⁺ concentration. Upconversion processes in these samples result from not only a two-photon excited-state absorption process but also a nonradiative energy transfer and cross-relaxation process.