Modeling deformation of a melt-infiltrated SiC/SiC composite under fatigue loading

Results from fatigue experiments done on a SiC/SiC composite are presented. A micromechanics-based model is used to study the observed behavior under cyclic loading. The model includes consideration of progressive damage, creep and oxidation of the fiber and matrix. Comparison of model predictions with test data showed that the deformation during fatigue in this material is explained primarily by damage in the form of matrix microcracking and interface debonding, in combination with creep under the cyclic load. Stiffness of the material was observed to not change significantly during fatigue indicating that the contribution of fiber fracture to deformation is limited. Fiber fracture however was found to determine final failure of the composite. Failure under cyclic fatigue loading was found to be affected by load transfer from the matrix to the fiber due to damage and creep, and by progressive degradation of the load-carrying fibers due to the combined effect of oxidation and load cycling.     

Micromechanical model of time-dependent damage and deformation behavior for an orthogonal 3D-woven SiC/SiC composite at elevated temperature in vacuum

This paper presents a micromechanical model to predict the time-dependent damage and deformation behavior of an orthogonal 3-D woven SiC fiber/BN interface/SiC matrix composite under constant tensile loading at elevated temperature in vacuum. In-situ observation under monotonic tensile loading at room temperature, load–unload tensile testing at 1200 °C in argon, and constant load tensile testing at 1200 °C in vacuum were conducted to investigate the effects of microscopic damage on deformation behavior. The experimentally obtained results led to production of a time-dependent nonlinear stress–strain response model for the orthogonal 3-D woven SiC/SiC. It was established using the linear viscoelastic model, micro-damage propagation model, and a shear-lag model. The predicted creep deformation was found to agree well with the experimentally obtained results.     

A synergistic model of stress and oxidation induced damage and failure in silicon carbide-based ceramic matrix composites

A micromechanics-based modeling approach that allows for the simultaneous consideration of deformation, damage, and oxidation associated with each constituent of silicon carbide (SiC)-based ceramic matrix composites (CMC), including the fiber, fiber coating, and matrix, is described. Chemical kinetics models from the literature are combined with a progressive damage model. Rupture predictions of unnotched and notched stress-hold (creep) specimens are compared with experimental measurements from a SiC/SiC CMC to assess the efficacy of the modeling approach. Techniques of improving creep rupture life are explored using the model.     

Tensile creep behavior of SiCf/SiC ceramic matrix minicomposites

Single fiber-tow minicomposites represent the major load-bearing element of woven and laminate ceramic matrix composites (CMCs). To understand the effects of fiber type, fiber content, and matrix cracking on tensile creep in SiC_f/SiC CMCs, single-tow SiC_f/SiC minicomposites with different fiber types and contents were investigated. The minicomposites studied contained either Hi-Nicalon™ or Hi-Nicalon™ Type S SiC fibers with a boron nitride (BN) interphase and a chemical-vapor-infiltrated-silicon-carbide (CVI-SiC) matrix. Tensile creep was performed at 1200 °C in air. A bottom-up creep modeling approach was applied where creep parameters of the fibers and matrix were obtained separately at 1200 °C. Next, a theoretical model based on the rule of mixtures was derived to model the fiber and matrix creep-time-dependent stress redistribution. Fiber and matrix creep parameters, load transfer model results, and numerical modeling were used to construct a creep strain model to predict creep damage evolution of minicomposites with different fiber types and contents.     

Effect of multiple loading sequence on time-dependent stress rupture of fiber-reinforced ceramic-matrix composites

In this paper, the effect of multiple loading sequence on time-dependent stress rupture of fiber-reinforced ceramic-matrix composites (CMCs) at intermediate temperatures in oxidative environment is investigated. Considering multiple damage mechanisms, a micromechanical constitutive model for time-dependent stress rupture is developed to determine damage evolution of matrix crack spacing, interface debonding and oxidation length, and fiber failure probability under single and multiple loading sequences. The relationships between multiple loading sequence, composite strain evolution, time, matrix cracking, interface debonding and oxidation, and fiber fracture are established. The effects of fiber volume, matrix crack spacing, interface shear stress in the slip and oxidation region, and environment temperature on the stress/time-dependent strain, interface debonding and oxidation fraction, and fiber broken fraction of SiC/SiC composite are analyzed. The experimental stress rupture of SiC/SiC composite under single and multiple loading sequences at 950°C in air atmosphere is predicted. Compared with single loading stress, multiple loading sequence affects the interface debonding and oxidation fraction in the debonding region, leading to the higher fiber broken fraction and shorter stress-rupture lifetime.     

A chemo-mechanical coupled constitutive model applied to the oxidation simulation of SiC/SiC composite

Herein, a chemo-mechanical coupled constitutive and failure model is proposed to predict the tensile behavior of SiC/SiC composites under oxidizing environments. The diffusion of O₂ through the oxide scale and the oxidation reaction of SiC/O₂ are modeled and implemented in finite element software, through a user-defined element. Numerical validation studies and tests are conducted on a domestic SiC fiber. An orthotropic constitutive model for reinforcements, which considers modulus reduction due to oxidation damage, and a continuum damage model associated with O₂ diffusion along the micro-cracks in the SiC matrix are subsequently presented. The developed framework is used to simulate the mechanical behavior and oxidation process of a single fiber SiC/SiC composite.     

Compressive strength and damage mechanisms of 2D-C/SiC composites at high temperatures

Compressive strength of 2D-C/SiC composite was investigated from room temperature(RT) to 1600?°C at present work. Damage evolution was investigated by conducting loading/unloading tests at RT and the damage mechanisms were elucidated by observing the fracture morphology. It is found that compressive strength of 2D-C/SiC was retained until 1200?°C and then decreased with increasing temperature. The variation of compressive strength is closely related to the degradation in matrix modulus. The compressive damage of 2D-C/SiC starts at the buckling of 0° fiber and is followed by opening and closing of original pores, initiation and growth of longitudinal interbundle cracks, separation of 90° fiber bundles by longitudinal cracks, matrix cracking from intrabundle pores, propagation of matrix cracks into 0° fiber bundles, connection of cracks in 0° fiber bundles and longitudinal cracks in 90° fiber bundles.     

Mechanical Behavior of a Continuous-SiC-Fiber-Reinforced RBSN-Matrix Composite

The results of a detailed study are presented on the toughening of reaction-bonded silicon nitride reinforced with large-diameter SiC monofilaments at ambient and elevated temperatures. Composite stiffness, strength, toughness, and R -curve behavior were investigated at ambient temperature, with strengths measured up to 1400°C. At elevated temperature, toughening mechanisms were explored by investigating crack initiation and growth under creep conditions. The results show that, at ambient temperature, the composite exhibited noncatastrophic failure with substantial toughening associated with contributions of both fiber pullout and elastic bridging of fibers in the crack wake, consistent with predictions using available models. Limited R -curve measurements suggest that large-scale bridging effects may be present. At elevated temperature, crack initiation occurred in the matrix at about 1000°C, but in the fiber at higher temperatures. Growth of cracks is governed by time-dependent bridging of unbroken fibers in the crack wake, consistent with a model based on fiber pullout by viscous sliding of fibers out of the matrix along amorphous interfacial layers.     

Effects of cyclic tensile loading on the rupture behavior of orthogonal 3-D woven SiC fiber/SiC matrix composites at elevated temperatures in air

This study examined the rupture mechanisms of an orthogonal 3D woven SiC fiber/BN interface/SiC matrix composite under combination of constant and cyclic tensile loading at elevated temperature in air. Monotonic tensile testing, constant tensile load testing, and tension–tension fatigue testing were conducted at 1100 °C. A rectangular waveform was used for fatigue testing to assess effects of unloading on the damage and failure behavior. Microscopic observation and single-fiber push-out tests were conducted to reveal the rupture mechanisms. Results show that both oxidative matrix crack propagation attributable to oxidation of the fiber–matrix interface and the decrease in the interfacial shear stress (IFSS) at the fiber–matrix interface significantly affect the lifetime of the SiC/SiC composites. A rupture strength degradation model was proposed using the combination of the oxidative matrix crack growth model and the IFSS degradation model. The prediction roughly agreed with the experimentally obtained results.     

A progressive damage model for ceramic matrix mini-composites with thick interphases

Toughness enhancement in ceramic matrix composites (CMCs) with brittle matrix and fiber phases is often accomplished by introducing a weak finite-thickness interphase between the fiber and matrix. The current work presents a progressive damage model to predict the tensile response of single tow CMCs (mini-composite) representative of a unidirectional composite at the microscale. Implementation of a 3-phase shear-lag model for a geometrically accurate representation of the underlying microstructure in CMCs with finite thickness interphase has been highlighted. A probabilistic progressive modeling approach has been adopted, accounting for multiple matrix cracking, interfacial debonding, and fiber failure in 3-phase mini-composites. The predicted tensile response of CMCs from the progressive damage modeling approach agrees with experimental results obtained for C/BN/SiC mini-composites validating the approach.     

Microstructure and tensile behavior of (BN/SiC)n coated SiC fibers and SiC/SiC minicomposites

Interphase plays an important role in the mechanical behavior of SiC/SiC ceramic-matrix composites (CMCs). In this paper, the microstructure and tensile behavior of multilayered (BN/SiC)_n coated SiC fiber and SiC/SiC minicomposites were investigated. The surface roughness of the original SiC fiber and SiC fiber deposited with multilayered (BN/SiC), (BN/SiC)₂, and (BN/SiC)₄ (BN/SiC)₈ interphase was analyzed through the scanning electronic microscope (SEM) and atomic force microscope (AFM) and X-ray diffraction (XRD) analysis. Monotonic tensile experiments were conducted for original SiC fiber, SiC fiber with different multilayered (BN/SiC)_n interfaces, and SiC/SiC minicomposites. Considering multiple damage mechanisms, e.g., matrix cracking, interface debonding, and fibers failure, a damage-based micromechanical constitutive model was developed to predict the tensile stress-strain response curves. Multiple damage parameters (e.g., matrix cracking stress, saturation matrix crack stress, tensile strength and failure strain, and composite’s tangent modulus) were used to characterize the tensile damage behavior in SiC/SiC minicomposites. Effects of multilayered interphase on the interface shear stress, fiber characteristic strength, tensile damage and fracture behavior, and strength distribution in SiC/SiC minicomposites were analyzed. The deposited multilayered (BN/SiC)_n interphase protected the SiC fiber and increased the interface shear stress, fiber characteristic strength, leading to the higher matrix cracking stress, saturation matrix cracking stress, tensile strength and fracture strain.     

Creep behavior and failure mechanisms of CVI and PIP SiC/SiC composites at temperatures to 1650 °C in air

Creep properties of 2D woven CVI and PIP SiC/SiC composites with Sylramic™-iBN SiC fibers were measured at temperatures to 1650 °C in air and the data was compared with the literature. Batch-to-batch variations in the tensile and creep properties, and thermal treatment effects on creep, creep parameters, damage mechanisms, and failure modes for these composites were studied. Under the test conditions, the CVI SiC/SiC composites exhibited both matrix and fiber-dominated creep depending on stress, whereas the PIP SiC/SiC composites displayed only fiber-dominated creep. Creep durability in both composite systems is controlled by the most creep resistant phase as well as oxidation of the fibers via cracking matrix. Specimen-to- specimen variations in porosity and stress raisers caused significant differences in creep behavior and durability. The Larson-Miller parameter and Monkman-Grant relationship were used wherever applicable for analyzing and predicting creep durability.     

Tensile creep behavior of unidirectional glass‐fiber polymer composites

The tensile creep behavior of unidirectional glass‐fiber polymer composites was studied at three different temperatures, namely 298, 333, and 353 K. Testing was performed on the pure epoxy matrix, the 0° specimens as well as off‐axis at 15, 30, and 60 degrees in respect to the axis of tension. The creep strain rate was negligible at room temperature, while it was considerable at the higher temperatures examined. The materials exhibit nonlinear viscoelastic behavior, and the creep response of the composites was treated as a thermally activated rate process. The creep strain was considered to include an elastic, a viscoelastic and a viscoplastic part. The viscoplastic part was calculated through a functional form, developed in a previous work, assuming that viscoplastic response of polymer composites arises mainly from the matrix viscoplasticity. The model predictions in terms of creep compliances were found to be satisfactory, compared with the experimental results. POLYM. COMPOS. 26:287–292, 2005. © 2005 Society of Plastics Engineers.     

Correlating Electrical Resistance Change with Mechanical Damage in Woven SiC/SiC Composites: Experiment and Modeling

Silicon carbide (SiC) fiber‐reinforced SiC matrix composites are inherently multifunctional materials. In addition to their primary function as a structural material, the electric properties of the SiC/SiC composites could be used for the sensing and monitoring of in situ damage nucleation and evolution. To detect damage and use that information to further predict the useful life of a particular component, it is necessary to establish the relationship between damage and electrical resistance change. Here, two typical SiC/SiC composites, melt infiltrated (MI), and chemical vapor infiltrated (CVI) woven SiC/SiC composites, were tested to establish the relationship between the electrical response and mechanical damage in unload–reload tensile hysteresis tests. Compared to the 55% resistance increase seen for CVI composites, the MI SiC/SiC composites exhibit a maximum resistance change in 450% in response to mechanical loading (damage), which is the highest sensitivity known among various composites. An analytic model accounting for fiber breakage and matrix cracks was developed to link the electrical resistance to mechanical damage in the composites. The predictions from the models agree well with the experimental data for both composites with high and low conductive matrices. The residual resistance change after unloading is also correlated to the loading history by the analytical relationship. This study demonstrates that resistance change is sensitive to damage in a predictable manner and can be used to improve the reliability of damage assessment of SiC/SiC composites.     

Creep properties of melt infiltrated SiC/SiC composites with Sylramic™-iBN and Hi-Nicalon™-S fibers

Isothermal tensile creep tests were conducted on 2D woven and laminated, 0/90 balanced melt infiltration (MI) SiC/SiC composites at stress levels from 48 to 138 MPa and temperatures to 1400°C in air. Effects of fiber architecture and fiber types on creep properties, influence of accumulated creep strain on in-plane tensile properties, and the dominant constituent controlling the creep behavior and creep rupture properties of these composites were investigated. In addition, the creep parameters of both composites were determined. Results indicate that in 2D woven MI SiC/SiC composites with Sylramic™-iBN or Hi-Nicalon™-S fibers, creep is controlled by chemical vapor infiltration (CVI) SiC matrix, whereas in 2D laminated MI SiC/SiC composites with Hi-Nicalon™-S fibers, creep is controlled by the fiber. Both types of composites exhibit significant variation in creep behavior and rupture life at a constant temperature and stress, predominantly due to local variation in microstructural inhomogeneity and stress raisers. In both types of composites at temperatures >1350°C, residual silicon present in SiC matrix to reacts with SiC fibers and fiber coating causing premature creep rupture. Using the creep parameters generated, the creep behaviors of the composites have been modeled and factors influencing creep durability are discussed.     

Creep analysis of polymeric pipes under internal pressure

Medium density polyethylene pipes have been used in the water and gas industries for over a decade. One of the major problems with these pipes is creep under their service pressures. Life prediction is usually based on the secondary creep path until the onset of tertiary creep. Constitutive models such as visco‐hyperelasticity and elasto‐viscoplasticity can be used to make such prediction. Owing to complexity, the latter is usually used in numerical modeling, Medium density polyethylene is an extremely ductile material with a low modulus of elasticity. The corresponding elongation prior to rupture under a tensile creep test can reach a few hundred percent. The appropriate creep law must be established before any life prediction can be made. In this paper, based on a creep law obtained from a series of material creep tests under different stress levels, a visco‐hyperelastic model was developed to simulate Medium density polyethylene pipes under internal creep pressures. Reasonably good correlation has been obtained between the experimental results and the theoretical analysis.     

Damage analysis of a SiCf/SiC ceramic matrix composite under stepwise fatigue loading with acoustic emission

Continuous fiber-reinforced ceramic matrix composites (CMCs) exhibit different damage mechanisms at multiple scales under cyclic loading. In this paper, the tension-tension fatigue behavior of a plain woven SiC_f/SiC CMC was investigated, and damage accumulation and evolution process were studied in detail via acoustic emission (AE) method. With the increase of cycles, the material exhibits obvious hysteresis behavior affected by interfacial slip and wear mechanisms. Most of the fibers with radial fracture characteristic have relatively high strength, showing excellent toughening property. In the stepwise cyclic loading process, the Kaiser effect of AE determines the initiation of AE activities at each initial loading moment, which shows obvious nonlinear damage accumulation behavior of the material. High-energy events are related to significant matrix cracking and fiber fracture, and the evolution process of material damage initiation and propagation is monitored in real time.     

Tensile creep properties and damage mechanisms of 2D-SiCf/SiC composites reinforced with low-oxygen high-carbon type SiC fiber

Tensile creep properties of 2D-SiC_f/SiC composites reinforced with low-oxygen high-carbon type SiC fibers were studied in vacuum at 1300°C∼1430°C. The fracture morphology was observed by scanning electron microscopy and the damage of fiber in 2D-SiC_f/SiC composites was characterized by nanoindentation. Moreover, the microstructure of the composite was investigated by high-resolution transmission electron microscopy. The results show that rupture time is much shortened and steady-state creep rate increase three orders of magnitude when creep temperature is higher than 1400°C. There are two different creep damage mechanisms due to the decrease of interfacial bonding strength at high temperature. The amorphous SiO_xC_y phase in the fibers can crystallize into SiC and C and the SiC grain grows in the fiber. The microstructural changes lead to the decrease of fiber strength and degrade the creep properties of the composite above 1400°C.     

Tensile creep and rupture of 2D-woven SiC/SiC composites for high temperature applications

The tensile creep and rupture behavior of 2D-woven SiC fiber-reinforced SiC matrix composites with potential for advanced high temperature structural applications was determined in air at 1315 °C. The results are compared to similar SiC/SiC data in the literature in order to understand the underlying creep and rupture mechanisms. Focus was placed on three different near-stoichiometric SiC fiber-types and three SiC-based matrix systems produced by different process routes. In general, the creep and rupture properties of the tested composites were primarily dictated by the creep resistance of the fiber-type, with the Sylramic-iBN fiber typically showing the best behavior. However, the type of matrix did have an effect on the composite creep and rupture lives due to load-sharing differences for the different matrix types and due to stoichiometry in the case of chemical vapor infiltration SiC matrices.     

Study on interfacial debonding stress and damage mechanisms of C/SiC composites using acoustic emission

Among ceramic matrix composites (CMCs), carbon fiber-reinforced silicon carbide matrix (C/SiC) composites are widely used in numerous high-temperature structural applications because of their superior properties. The fiber–matrix (FM) interface is a decisive constituent to ensure material integrity and efficient crack deflection. Therefore, there is a critical need to study the mechanical properties of the FM interface in applications of C/SiC composites. In this study, tensile tests were conducted to evaluate the interfacial debonding stress on unidirectional C/SiC composites with fibers oriented perpendicularly to the loading direction in order to perfectly open the interfaces. The characteristics of the material damage behaviors in the tensile tests were successfully detected and distinguished using the acoustic emission (AE) technique. The relationships between the damage behaviors and features of AE signals were investigated. The results showed that there were obviously three damage stages, including the initiation and growth of cracks, FM interfacial debonding, and large-scale development and bridging of cracks, which finally resulted in material failure in the transverse tensile tests of unidirectional C/SiC composites. The frequency components distributed around 92.5 kHz were dominated by matrix damage and failure, and the high-frequency components distributed around 175.5 kHz were dominated by FM interfacial debonding. Based on the stress and strain versus time curves, the average interfacial debonding stress of the unidirectional C/SiC composites was approximately 1.91 MPa. Furthermore, scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDXS) were used to observe the morphologies and analyze the chemical compositions of the fractured surfaces. The results confirmed that the fiber was completely debonded from a matrix on the fractured surface. The damage behaviors of the C/SiC composites were mainly the syntheses of matrix cracking, fiber breakage, and FM interfacial debonding.