Effect of Al in slag blended cement paste under sulfate attack

Unilateral sulfate attack of cementitious materials containing 40% slag with different water to binder ratios was investigated. The results showed that the degradation of slag blended cement pastes was nearly from the corners of paste surface with cracking and spallings, water-to-binder(w/b) ratio made a significant sense to the damage that low w/b ratio led to little weight loss, less cracking and spalling damage and vice versa. Microstructural experimental results demonstrated that in the three different stages of sulfate attack, degradation of pastes was primarily associated with the migration behavior and bonding configuration of aluminum, in the early ages Al was mostly present in C-(A)-S-H, and thus, the damage of pastes hardly appeared while at later ones Al had been largely transferred from C-(A)-S-H into AFt, leading to expansive damage.     

Structural and electrical properties of high Curie temperature Aurivillius phase composite ceramics with largely enhanced piezoelectricity

High performance piezoelectric ceramics with high Curie temperatures(TC) are the bottle necks of relevant high temperature devices. In this study, the electrical performance and microstructure of Li and Mn codoped Aurivillius-type composite ceramics with a composition Ca_(0.99-x_Bi_(6.99+x)(Li Mn)_(0.01) Nb Ti_5O_(24)(x = 0–0.8) were systematically investigated. The results indicated that uniform intergrowth structure with a lattice similar to that of the end member CBT could be formed at a low x value(x 0.4). Phase separation occurred when more A-site Ca~(2+) ions were replaced by Bi~(3+) ions. Nevertheless, all composite samples showed d_(33) values about 2 to 3 times of that of the constituent phase Ca Bi_4Ti_4O_(15) and Bi_3 Ti NbO_9 with still a high depolarization temperature. The performance of the samples was found to be related to the density and larger lattice distortion along the polarization a axis. The results also demonstrated that formation of the compound system was an effective way in improving the performance of Aurivillius-type high TC piezoelectric ceramics.     

Effect of corrosive solutions on C-S-H microstructure in portland cement paste with fly ash

By means of ²⁹Si and ²⁷Al magic angle spinning nuclear magnetic resonance (MAS NMR) combined with deconvolution technique, X-ray diffraction (XRD), scanning electron microscopy (SEM) as well as energy dispersive X-ray system(EDX), the effect of 5 wt% corrosive solutions (viz. 5 wt% Na₂SO₄, MgSO₄, Na2SO4+NaCl and Na₂SO₄+NaCl+Na₂CO₃) on C-S-H microstructure in Portland cement containing 30 wt% fly ash was investigated.The results show that, in MgSO₄ solution, Mg²⁺ promotes the decalcification of C-S-H by SO ₄ ^2- ,increasing silicate tetrahedra polymerization and mean chain length (MCL) of C-S-H. However, the substituting degree of Al³⁺ for Si⁴⁺ (Al[4]/Si) in the paste does not change evidently. Effect of Na²SO⁴ solution on C-S-H is not significantly influenced by NaCl solution, while the MCL and Al[4]/Si of C-S-H in fly ashcement paste slightly change. However, the decalcification of C-S-H by SO ₄ ^2- and CO ₃ ^2- attack, as well as the activation of fly ash by SO ₄ ^2- attack will increase the MCL and Al[4]/Si, which are both higher than that under Na₂SO₄ corrosion, MgSO₄ or Na₂SO₄ +NaCl coordination corrosion.     

Effects of annealing processes on Cu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Si<Subscript>1-<Emphasis Type="Italic">x</Emphasis></Subscript> thin films

The Cu _x Si_1-x thin films have been grown by pulsed laser deposition (PLD) with in situ annealing on Si (001) and Si (111), respectively. The transformation of phase was detected by X-ray diffraction (XRD). The results showed that the as-deposited films were composed of Cu on both Si (001) and Si (111). The annealed thin films consisted of Cu + η”-Cu₃Si on Si (001) while Cu + η’-Cu₃Si on Si (111), respectively, at annealed temperature (T _a) = 300-600 °C. With the further increasing of T _a, at T _a= 700 °C, there was only one main phase, η”-Cu₃Si on Si (001) while η’-Cu₃Si on Si (111), respectively. The annealed thin films transformed from continuous dense structure to scattered-grain morphology with increasing T _a detected by field emission scanning electron microscope (FESEM). It was also showed that the grain size would enlarge with increasing annealing time (t _a).     

Effects of H<Subscript>2</Subscript>/CO/CH<Subscript>4</Subscript> syngas composition variation on the NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> and CO emission characteristics in a partially-premixed gas turbine combustor

This paper reports the effects of variations in the fuel composition of H₂/CO/CH₄ syngas on the characteristics of NO _x and CO emissions in a partially-premixed gas turbine combustor. Combustion tests were conducted on a full range of fuel compositions by varying each component gas from 0% to 100% at heat inputs of 40 and 50 kW_th. Flame temperature, combustor liner temperature, ignition delay time, and flame structure were investigated computationally and experimentally to judge whether they are significant indicators of NO _x and CO formation. The characteristics of and reasons for NO _x and CO emissions were investigated by analyzing the emission mechanisms and relationships among fuel property, equivalence ratio, flame temperature, liner temperature, flame shape. The flame structures were investigated using the following flame visualization methods: (1) time-averaged OH* chemiluminescence and its Abel-deconvolution; (2) direct photography; and (3) instantaneous OH-PLIF. The flame structures were greatly changed by the fuel composition and heat input, and they were subjected to key affecting parameters of the temperatures of the flames and the liners. NO _x and CO emissions also largely varied according to fuel composition and heat input, showing neither linearly nor exponentially clear proportional trends toward the syngas compositions because of the singular conditions. For example, only the 100% CO flame at low load emitted lots of CO, whereas complete combustion was observed in other cases. However, the qualitative observations showed that the root causes of NO _x emission behaviors were flame temperature and flame structure, which were directly related to the residence time in the flame. Various sets of practical test results were obtained, and these results could contribute to the optimal selection of the fuel-feeding condition when fuel is changed from natural gas to syngas in order to minimize NO _x and CO emissions with stable combustion.     

Rheological behaviors of fresh cement pastes with polycarboxylate superplasticizer

The rheologicalbehaviors of fresh cement paste with polycarboxylate superplasticizer were systematically investigated.Influentialfactors including superplasticizer to cement ratio(Sp/C),water to cement ratio(w/c),temperature,and time were discussed.Fresh cement pastes with Sp/Cs in the range of 0 to 2.0% and varied W/Cs from 0.25 to 0.5 were prepared and tested at 0,20 and 40 °C,respectively.Flowability and rheologicaltests on cement pastes were conducted to characterize the development of the rheologicalbehavior of fresh cement pastes over time.The exprimentalresults indicate that the initialflowability and flowability retention over shelf time increase with the growth in superplasticizer dosage due to the plasticizing effect and retardation effect of superplasticizer.Higher temperature usually leads to a sharper drop in initialflowability and flowability retention.However,for the cement paste with high Sp/C or w/c,the flowability is slightly affected by temperature.Yield stress and plastic viscosity show similar variation trends to the flowability under the abovementioned influentialfactors at low Sp/C.In the case of high Sp/C,yield stress and plastic viscosity start to decline over shelf time and the decreasing rate descends at elevated temperature.Moreover,two equations to roughly predict yield stress and plastic viscosity of the fresh cement pastes incorporating Sp/C,w/c,temperature and time are developed on the basis of the existing models,in which experimentalconstants can be extracted from a database created by the rheologicaltest results.     

Nanostructuring and thermoelectric properties of bulk N-type Mg<Subscript>2</Subscript>Si

Preparation and thermoelectric properties of nanostructured n-type Mg₂Si bulk materials were reported. Nanosized Mg₂Si powder was obtained by mechanical milling of the microsized Mg₂Si powder prepared by solid-state reaction. The bulk materials with 30 nm and 5 µm were prepared by spark plasma sintering of the nanosized and microsized Mg₂Si powder, respectively. Both the samples show n-type conduction and the Seebeck coefficient of the sintered samples increase determinately with the grain size decrease from 5 µm to 30 nm. On the other hand, the electrical and thermal conductivity decrease with the decrease of grain size. Accordingly, decreasing their grain size increases their thermoelectric-figure-of-merit. A maximum thermoelectric figure of merit of 0.36 has been obtained for the nanostuctured Mg₂Si sample at 823 K, which is 38% higher than that of microsized Mg₂Si bulk materials and higher than results of other literatures. It could be expected that the properties of the nanocomposites could be further improved by doping optimization.     

Remarkable improvement of ferroelectric properties and leakage current in BiFeO<Subscript>3</Subscript> thin films by nd modification

Ferroelectric and leakage properties are important for ferroelectric applications. Pure and Nd-doped (x=0.05-0.20) BiFeO3 thin films were fabricated by sol-gel method on FTO substrates. The phase structure, surface morphology, leakage current, ferroelectric properties, and optical properties of BiFeO₃^- based thin films were investigated. The substitution of Nd³⁺ ions for the Bi3+ site converts the structure from rhombohedral to coexisting tetragonal and orthorhombic. Nd doping improves the crystallinity of BiFeO₃ thin films. The leakage current of Nd-doped BiFeO₃ decreases by two to three orders of magnitude compared with that of pure BiFeO₃. Among the samples, 15% Nd-doped BiFeO₃ exhibits the strongest ferroelectric polarization of 17.96 μC/cm². Furthermore, the absorption edges of Bi_1-xNd _x FeO₃ thin films show a slight red-shift after Nd doping.     

Synthesis of MnxZn（1-x）Fe2O4 Nanopartieles by Ball-milling Hydrothermal Method

SMnxZn1-xFe2O4 （x=1,0.9,0.8,0.7,0.6,0.5,0.25,0） nanoparticles were prepared by ball-milling hydrothermal and investigated by X-ray diffraction, DTG and TEM. Nanocrystallite grain size was determined by X-ray linewidth to be from 63 A to 274 A. The thermal properties indicate absorbed water still remain at low temperature, crystalline wate will be decomposed from 230 ℃ to 260 ℃, partial Mn^2＋ will be oxidized near 730 ℃. TEM shows the ferrite particles pocess a spherical morphology and uniform nanosize.     

Composition dependence of phase structure and electrical properties of (1−y)Bi1−xNdxFeO3−yBiScO3 ceramics

In this work, we have studied a new lead-free ceramic of(1-y)Bi_(1-x)Nd_xFeO_(3-y)BiScO_3(0.05≤x≤0.15 and 0.05≤y≤0.15) prepared by a conventional solid-state method, and the influences of Nd and Sc content on their phase structure and electrical properties were investigated in detail. The ceramics with 0.05≤x≤0.10 and 0.05≤y≤0.15 belong to an R3 c phase, and the rhombohedral-like and orthorhombic multiphase coexistence is established in the composition range of 0.125≤x≤0.15 and y=0. The electrical properties of the ceramics can be enhanced by modifying x and y values. The highest piezoelectric coefficient(d33~51 p C/N) is obtained in the ceramics with x=0.075 and y=0.125, which is superior to that of a pure BiFeO_3 ceramic. In addition, a lowest dielectric loss(tan δ~0.095%, f=100 k Hz) is shown in the ceramics with x=0.15 and y=0 due to the involvement of low defect concentrations, and the improved thermal stability of piezoelectricity at 20–600oC is possessed in the ceramics. We believe that the ceramics can play a meaningful role in the high-temperature lead-free piezoelectric applications.     

Influence of elevated curing temperature on the properties of cement paste and concrete at the same hydration degree

Three different curing temperatures(20 ℃, 40 ℃, and 60 ℃) were set, so that the nonevaporable water(w_n) contents of plain cement pastes cured at these three temperatures were measured to determine the hydration degree of cement. Tests were carried out to compare the pore structure and strength of cement paste, as well as the strength and permeability of concrete under different temperature curing conditions when their cements were cured to the same hydration degree. The experimental results show that either at a relatively low hydration degree(w_n=15%) or high hydration degree(w_n=16.5%), elevated curing temperature has little influence on the hydration products of cement paste, while it has a negative influence on the pore structure and compressive strength of cement paste. However, this negative effect is weaker at high hydration degree. The large capillary pore(100 nm) volumes of cement pastes remain almost the same at high hydration degree, regardless of curing temperatures. As for the concrete, elevated curing temperature also has negative influence on its compressive strength development, at both low hydration degree and high hydration degree. And this negative effect is stronger than that on cement paste's compressive strength at the same hydration degree. On the whole, elevated curing temperature has little influence on the resistance of concrete to chloride ion penetration.     

Influence of deposition pressure on properties of ZnO: Al films fabricated by RF magnetron sputtering

Transparent conductive aluminum doped zinc oxide(ZnO:Al,AZO) films were prepared on glass substrates by rf(radio frequency) magnetron sputtering from ZnO: 3wt% Al_2O_3 ceramic target. The effect of argon gas pressure(PAr) was investigated with small variations to understand the influence on the electrical, optical and structural properties of the films. Structural examinations using X-ray diffraction(XRD) and scanning electron microscopy(SEM) showed that the ZnO:Al thin films were(002) oriented. The resistivity values were measured by four-point probe with the lowest resistivity of 5.76×10~(-4) Ω?cm(sheet resistance=9.6 Ω/sq. for a thickness=600 nm) obtained at the PAr of 0.3 Pa. The transmittance was achieved from ultravioletvisible(UV-VIS) spectrophotometer, 84% higher than that in the visible region for all AZO thin films. The properties of deposited thin films showed a significant dependence on the PAr.     

Enhanced Ferroelectric Polarization in Laser-ablated Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> Thin Films by Controlling Preferred Orientation

Polycrystalline Bi₄Ti₃O₁₂ thin films with various fractions of a-axis, c-axis and random orientations have been grown on Pt(111)/Ti/SiO₂/Si substrates by laser-ablation under different kinetic growth conditions. The relationship between the structure and ferroelectric property of the films was investigated, so as to explore the possibility of enhancing ferroelectric polarization by controlling the preferred orientation. The structural characterization indicated that the large growth rate and high oxygen background pressure were both favorable for the growth of non-c-axis oriented grains in the Bi₄Ti₃O₁₂ thin films. The films with high fractions of a-axis and random orientations, i e, f (a-sxis) = 28.3% and f (random) = 69.6%, could be obtained at the deposition temperature of 973 K, oxygen partial pressure of 15 Pa and laser fluence of 4.6 J/cm², respectively. It was also noted that the variation of ferroelectric polarization was in accordance with the evolution non-c-axis orientation. A large value of remanent polarization (2Pr = 35.5 μC/cm²) was obtained for the Bi₄Ti₃O₁₂ thin films with significant non-c-axis orientation, even higher than that of rare-earth-doped Bi₄Ti₃O₁₂ films.     

Effect of Cu-Ti-C reaction composition on reinforcing particles size of TiC<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Cu composites

TiC _x /Cu composites were fabricated by combustion synthesis and hot press technology. Using XRD, SEM, EDS, FESEM analysis methods, the effects of various carbon sources and different Cu contents on the microstructures of TiC _x /Cu composites and the size of TiC _x particles were investigated. Results showed that TiC _x reinforcing particles size increases with decreasing Cu content in Cu-Ti-C reaction system. With carbon nanotubes (carbon black) serving as carbon source, the generated TiC _x particles size transits from nanometer to submicron when Cu content corresponding to the reaction system is reduced to 60 vol% (70 vol%); while graphite serves as carbon source, there is no clear limiting concentration. C particles with smaller size, larger specific surface area and better distribution result in finer TiC _x particles, which is more beneficial to generating nano-sized TiC _x /Cu composites.     

Effect of pH on crystallization of nanocrystalline zirconia in a microwave-hydrothermal process

Nanocrystalline zirconia (ZrO₂) was synthesized using a microwave-hydrothermal process. The effect of pH on the crystallization of the ZrO₂ powders was investigated. The phase and microstructure of ZrO₂ powders were examined using X-ray diffraction (XRD), Raman spectroscopy, and transmission electron microscopy (TEM). Results show that pure m-ZrO₂ can be obtained at low pH (pH<2). Pure t-ZrO₂ is formed at pH = 7 and 14. The size of the ZrO₂ crystals is in the range of 8-26 nm and decreases with increasing pH. The formation of m-ZrO₂ results from the precipitation of ZrO₂ from solution. The t-ZrO₂ is formed through the in-situ structural rearrangement of amorphous Zr(OH) _x O _y . The stabilization of t-ZrO₂ is attributed to the small crystal size and the adsorption of hydroxy ions on the surfaces of the crystals.     

Effect of Curing Regime on Degree of Al3＋ Substituting for Si4＋ in C-S-H Gels of Hardened Portland Cement Pastes

The effect of curing regime on degree of Al3+ substituting for Si4+(Al/Si ratio) in C-S-H gels of hardened Portland cement pastes was investigated by 29Si magic angel spinning(MAS) nuclear magnetic resonance(NMR) with deconvolution technique. The curing regimes included the constant temperature(20, 40, 60 and 80 ℃) and variable temperature(simulated internal temperature of mass concrete with 60 ℃ peak). The results indicate that constant temperature of 20 ℃ is benefi cial to substitution of Al3+ for Si4+, and Al/Si ratio changes to be steady after 180 d. The increase of Al/Si ratio at 40 ℃ is less than that at 20 ℃ for 28 d. The other three regimes of high temperature increase Al/Si ratio only before 3 d, on the contrary to that from 3 to 28 d. However, the 20 ℃ curing stage from 28 to 180 d at variable temperature regime, is benefi cial to the increase of Al/Si ratio which is still lower than that at constant temperature regime of 20 ℃ for the same age. A nonlinear relation exists between the Al/Si ratio and temperature variation or mean chain length(MCL) of C-S-H gels, furthermore, the amount of Al3+ which can occupy the bridging tetrahedra sites in C-S-H structure is insuffi cient in hardened Portland cement pastes.     

Microstructural Evolution Mechanism of C-(A)-S-H Gel in Portland Cement Pastes Affected by Sulfate Ions

The microstructural evolution of C-(A)-S-H gel in Portland cement pastes immersed in pure water and 5.0 wt% Na₂SO₄ solution for different ages was comparatively investigated, by means of ²⁹Si NMR spectroscopy, and SEM-EDS analysis. Additionally, molecular dynamics simulation was performed to study the aluminum coordination status and interaction of sulfate ions in C-(A)-S-H gel. The results showed significant changes in the microstructural evolution of C-(A)-S-H gel in Portland cement paste. Sulfate attack has decalcifying and dealuminizing effect on C-(A)-S-H gel which is evident from increase in mean chain length (MCL) and decrease in Ca/Si & Al[4]/Si ratios of C-(A)-S-H gel. Additionally, Molecular dynamics simulation proves that Al[4] substituted in silicate chains of C-(A)-S-H gel is thermodynamically metastable, which may explain its migration from the silicate chains and transformation to Al[6], thus lowering the Al[4]/Si ratio of C-(A)-S-H gel. SO₄^2- ions can carry the interfacial Ca²⁺ ions into the pore solution by the diffusion-absorption-desorption process, which unravels the mechanism of sulfate attack on C-(A)-S-H gel.     

Preparation and piezoelectric properties of CuO-added (Ag<Subscript>0.75</Subscript>Li<Subscript>0.1</Subscript>Na<Subscript>0.1</Subscript>K<Subscript>0.05</Subscript>)NbO<Subscript>3</Subscript> lead-free ceramics

CuO-doped (Ag_0.75Li_0.1Na_0.1K_0.05)NbO₃ (ALNKN-xCuO, x = 0–2mol%) lead-free piezoelectric ceramics were prepared by the solid-state reaction method in air atmosphere. The effects of CuO addition on the phase structure, microstructure, and piezoelectric properties of the ceramics were investigated. The experimental results show that the ALNKN ceramics without doping CuO possess rhombohedral phase along with K2Nb6O16-type phase and metallic silver phase. For all of the CuO-doped ALNKN ceramics, a pure perovskite structure with the orthorhombic phase was obtained by enclosing the samples in a corundum tube. A homogeneous microstructure with the grain size of about 1 μm was formed for the ceramics with 0.5mol% CuO. The grain size increases with increasing amount of CuO. The temperature dependence of dielectric properties indicates that the ferroelectric phase of the ALNKN-xCuO ceramics becomes less stable with the addition of CuO. The ceramics with x = 1mol% exhibit relatively good electrical properties along with a high Curie temperature. These results will provide a helpful guidance to preparing other AN-based ceramics by solid-state reaction method in air atmosphere.     

Preparation and magnetic properties of Mn-Zn ferrites by the Co-precipitation method

Mn-Zn ferrites (Mn_1?x Zn _x Fe₂O₄) with different compositions were prepared by the coprecipitation method, and the influences of such synthesis conditions as pH value, composition and volume ratio (R) of the mixed solution and NH₄HCO₃ solution on their microstructures and magnetic properties were discussed. The samples were characterized by X-ray diffraction (XRD) and magnetization measurement instrument. Lattice parameters and average crystalline size of the synthesized materials were calculated from the corresponding XRD patterns with the related software Jade.5. For samples of different pH values, only one phase was found when pH values were 7.0, 8.0 and 9.0. The sample with pH value of 7.0 exhibited the highest saturation magnetic induction, the lowest coercive force, and crystallized best. For samples of different R values with pH value of 7.0, only one phase was observed in all samples, and the sample with R value of 2.3 exhibited the highest saturation magnetic induction and the lowest coercive force. The composition has mainly afected the magnetic properties, and the saturation magnetic induction increases with the increase of the content of Zn (x), but decreases when x is beyond 0.6. The trend of coercive force is on the contrary. However, no magnetism is exhibited when the x value is up to 0.8.     

A statistical approach to fit Gaussian part of full-energy peaks from Si(PIN) and SDD X-ray spectrometers

A new statistical fitting approach,named Statistical Distribution-Based Analytic(SDA)method,is proposed to fit single Gaussian-shaped Kαand KβX-ray peaks recorded by Si(PIN)and silicon drift detector(SDD).In this method,we use the discrete distribution theory to calculate standard deviation of energy resolutionσ.The calibration ofσand energy(E)for two detectors between the energy ranges of 4.5–26 keV are also completed by measuring characteristic X-ray spectra of nineteen types of pure elements.With the spectrum fraction(SF)parameter proposed in this paper,the SDA method can be used to resolve overlapping peaks.In measured spectra,the Gaussian part of X-ray peaks can be fitted by a Gaussian function with two parameters,σand SF.This new fitting approach is simpler than traditional methods and it achieves relatively good results when fitting the complex X-ray spectra of national standard alloy samples detected by Si(PIN)and SDD detectors.The2r values are obtained for each spectrum to assess fitting results,and the SDA fitting method gives a preferable fit for the SDD detector.