Effect of Fe(III) impurity on the electrochemical performance of LiFePO_4 prepared by hydrothermal process

Lithium iron phosphate (LiFePO4) was synthesized from LiOH, FeSO4 and H3PO4 by a hydrothermal process at 180℃. The samples were characterized by X-ray diffraction, scanning electron microscopy and chemical analysis. Electrochemical performance of the samples was tested in terms of charge-discharge capacity and cycling behavior. The results indicated that Fe(III) impurity had obvi- ously effect on the electrochemical properties of LiFePO4, and the formation of Fe3 was caused by the oxidation of Fe2 in the dissolving and feeding processes accompanying the increase of pH value. It was found that the precipitation separation was effective in decreasing the content of Fe3 in the solu- tion of FeSO4 and the sealed feeding was useful in preventing the conversion of Fe2 to Fe3 . When the content of Fe3 < 0.5 wt%, the hydrothermally synthesized LiFePO4 calcined at 750℃ with sucrose as carbon source exhibited an initial discharge capacity of 154.9 mAh·g-1 at the rate of 0.1 C (1 C = 150 mA·g-1) and the cycling retention rate could reach 98% after 50 cycles at room temperature.     

Effect of pH values on photocatalytic properties of Bi<Subscript>2</Subscript>WO<Subscript>6</Subscript> synthesized by hydrothermal method

Highly crystalline orthorhombic Bi₂WO₆ powders were hydrothermally synthesized from aqueous solutions of Na₂WO₄ · 2H₂O and Bi (NO₃)₃ · 5H₂O over a wide range of pH. The effect of pH on morphologies, sizes and properties of the Bi₂WO₆ crystals was investigated. The band gaps of the as-prepared Bi₂WO₆ were determined from the onset of the absorption edge of UV-vis diffuse reflectance spectra. The methyl orange photodegradation was employed as a probe reaction to test the photocatalytic activity of the as-prepared samples under visible light irradiation. The photocatalytic activities of methyl orange degradation under visible light irradiation are strongly dependent on the pH used in the synthesis. The highest efficiency is observed at pH=7. Funded by the PCSIRT, the National Natural Science Foundation of China (Nos. 50532030 and 50625206) and the Zhejiang Provincial Natural Science Foundation of China (No. Z4080021)     

Synthesis and electrochemical properties of Cr-doped Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript> cathode materials for lithium-ion batteries

Cr-doped Li₃V₂(PO₄)₃ cathode materials Li₃V_2−x Cr _x (PO₄)₃ were prepared by a carbothermal reduction(CTR) process. The properties of the Cr-doped Li₃V₂(PO₄)₃ were investigated by X-ray diffraction (XRD), scanning electron microscopic (SEM), and electrochemical measurements. Results show that the Cr-doped Li₃V₂(PO₄)₃ has the same monoclinic structure as the undoped Li₃V₂(PO₄)₃, and the particle size of Cr-doped Li₃V₂(PO₄)₃ is smaller than that of the undoped Li₃V₂(PO₄)₃ and the smallest particle size is only about 1 μm. The Cr-doped Li₃V₂(PO₄)₃ samples were investigated on the Li extraction/insertion performances through charge/discharge, cyclic voltammogram (CV), and electrochemical impedance spectra(EIS). The optimal doping content of Cr was that x=0.04 in the Li₃V_2−x Cr _x (PO₄)₃ samples to achieve high discharge capacity and good cyclic stability. The electrode reaction reversibility was enhanced, and the charge transfer resistance was decreased through the Cr-doping. The improved electrochemical performances of the Cr-doped Li₃V₂(PO₄)₃ cathode materials are attributed to the addition of Cr³⁺ ion by stabilizing the monoclinic structure. Funded by the Guangxi Natural Science Foundation(No. 0832259) and the National Basic Research Program of China (No. 2007CB613607)     

Electrochemical properties of Nano-LiFePO<Subscript>4</Subscript> prepared by hydrothermal reaction

LiFePO4 nanorods were facilely synthesized under hydrothermal condition. The crystalline structure and particle morphology of LiFePO4 powders were characterized by X-ray diffraction (XRD), and field emission scanning electron microscopy (FE-SEM). The electrochemical properties of LiFePO4/Li cells were investigated by galvanostatic test and cyclic voltammetry (CV). The XRD result demonstrated LiFePO4 powder had an orthorhombic structure with a space group of Pnma. The synthesized LiFePO4 nanorods exhibited a...     

Effect of La doping on microstructure and ferroelectric properties of Bi<Subscript>4</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films prepared by sol-gel method

The Bi4Ti3Oi2 and Bi3.25La0.75Ti3O12 thin films were prepared on the Pt/Ti/SiO2/Si substrate using the sol-gel method. The effect of La doping on the microstructure and ferroelectric properties of Bi4Ti3O12 films were investigated. Both the Bi4Ti3O12 and Bi3.25La0.75Ti3O12 thin films exhibited typical bismuth layered perovskite structure. The 2Pr （remanent polarization） value of Bi3.25La0.75Ti3O12 thin films is 18.6 μC/cm^2, which is much larger than that of Bi4Ti3O12 thin films. And the Bi3.2eLa0.75Ti3O12 films show fatigue-free behavior, while the Bi4Ti3O12 thin films exhibit the fatigue problem. The mechanism of improvement of La doping was discussed.     

Cu<Subscript>2</Subscript>ZnSnS<Subscript>4</Subscript> thin films prepared by sulfurizing different multilayer metal precursors

Cu₂ZnSnS₄ (CZTS) thin films were successfully fabricated on glass substrates by sulfurizing Cu-Sn-Zn multilayer precursors, which were deposited by ion beam sputtering and RF magnetron sputtering, respectively. The structural, electrical and optical properties of the prepared films under various processing conditions were investigated in detail. Results showed that the as-deposited CZTS thin films with the precursors by both ion beam sputtering and RF magnetron sputtering have a composition near stoichiometric. The crystallization of the samples, however, has a strong dependence on the atomic percent of constituents of the prepared CZTS films. A single phase stannite-type structure CZTS with a large absorption coefficient of 10₄/cm in the visible range could be obtained after sulfurization at 520°C for 2 h. The samples relative to the RF magnetron sputtering showed a low resistivity of 0.073 Ωcm and band gap energy of about 1.53 eV. The samples relative to the ion beam sputtering exhibited a resistivity of 0.36 Ωcm and the band gap energy is about 1.51 eV. Supported by the National Natural Science Foundation of China (Grant No. 10574106), the Planned Science and Technology Project of Guangdong Province (Grant No.2003C05005) and the Natural Science Fund of Zhanjiang Normal University (Grant No.200801)     

Synthesis of Ti3SiC2/TiB2 Composite by In-situ Hot Pressing （HP） Method

Ti3SiC2/TiB2 composite was successfully obtained by hot pressing Ti/TiC/Si/B4C power mixtures.Volume fraction of TiB2 in Ti3SiC2/TiB2 composite can not exceed 10%.Incorporation of excessive TiB2 will affect the reactions process.TiC and Ti5Si3 were two important intermediate phases during the whole reactions.The microstructure characteristics of the Ti3SiC2/TiB2 composites were analyzed using scanning electron microscopy （SEM） and transmission electron microscopy （TEM）.The experimental results show that the grains of Ti3SiC2/TiB2 composite are structured in a layered form,and the formation of TiB2 particles as reinforcements with elongated or equiaxed shape distributes in Ti3SiC2 matrix.     

Structure and electrochemical properties of LiMn<Subscript>2</Subscript>O<Subscript>4</Subscript>−<Emphasis Type="Italic">x</Emphasis>F<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>

LiMn₂O₄−_xF_x prepared by the sol-gel method has a perfect crystal formation. The crystal particle size of the material was medium and distributed uniformly. The substitution of F for O increased the specific capacity of the material at the cost of the cycleability. The explanation of this results is that the F decreases the valence of Mn, that is, more Mn³⁺ and less Mn⁴⁺ exist in the material. The increase of Mn³⁺ will improve the initial specific capacity and Mn³⁺ is the original reason for Jahn-Teller effect that caused the poor cycleability of the cathode material by the micro-distortion of the crystal structure. In addition, the expanded measurement of the crystal lattice is also the reason for the poor cycleability. Therefore, the results of F-substitution and cation-substitution are opposite. If the two methods are combined, they can compensate the inability each other and the satisfactory results may be obtained. XIA Jun-lei: Born in 1977 Funded by the National Natural Science Foundation of China (No. 59972026)     

Controlled synthesis and magnetic properties of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> walnut spherical particles and octahedral microcrystals

Magnetite Fe₃O₄ walnut spherical particles and octahedral microcrystals were successfully synthesized from K₄ [Fe (CN)₆], K₃ [Fe (CN)₆] and NaOH reagents via a simple hydrothermal process. And the uniform morphology of octahedral microcrystals was obtained in the presence of ethylene glycol. The morphology and structure of products were characterized by powder X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The results showed that the Fe₃O₄ walnut spherical particles and octahedral microcrystals were single crystals with the face-center cubic structure and with size distributions from 2.2 to 8.6 μm and 1.6 to 12.5 μm, respectively. Their magnetic properties were detected by a vibrating sample magnetometer at room temperature. The walnut spherical particles exhibited a ferromagnetic behavior with the coercive force (Hc), saturation magnetization (Ms) and remanent magnetization (Mr) being 150.57 Oe, 97.634 and 12.05 emu/g, respectively. For the octahedral microcrystals they were 75.28 Oe, 101.90 and 6.69 emu/g, respectively. Different sizes of walnut spherical particles were controlled synthesized through adjusting the NaOH concentration. It was found that ethylene glycol molecules have a significant effect on the formation of Fe₃O₄ octahedra. A possible mechanism was also proposed to account for the growth of these Fe₃O₄ products. Supported by Fund of weinan Teachers University (Grant No. 08YKZ008), the National Natural Science Foundation of China (Grant No. 20573072) and Doctoral Fund of Ministry of Education of China (Grant No. 20060718010)     

Synthesis and characterization of (PEO)<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>−(V<Subscript>0.85</Subscript>Mo<Subscript>0.15</Subscript>)<Subscript>2</Subscript>O<Subscript>5</Subscript> nanocomposite films

(PEO) _x −(V_0.85Mo_0.15)₂O₅(x=0,0.5,1.0) nanocomposite films were prepared by a modified sol-gel method. The structure of the films was analyzed by XRD, and the DC electrical conductivity. Cyclic voltammogram and optical spectral transmittance were investigated. The results show that the (V_0.85Mo_0.15)₂O₅ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1.7897 nm at x=1.0. The introduction of MoO₃ improved the DC electrical conductivities of the films due to the generation of V₄₊ to maintain the electrical neutrality of the oxides. PEO intercalated in the interlayer of (V_0.85Mo_0.15)₂O₅ oxides has interaction with the oxides, enhancing the amount of Li⁺ ions inserted into the interlayer of the oxides. Moreover, the intercalation of PEO into the interlayer of (V_0.85Mo_0.15)₂O₅ oxides improved the cathodic electrochromic property in near ultraviolet region and anodic electrochromic property in visible range. JIANG Cong-sheng: Born in 1963 Supported by the Science Foundation of Hubei Province (Grant No. 2001ABB083)     

Domain structure and defects of highly ordered Bi<Subscript>4</Subscript>Si<Subscript>3</Subscript>O<Subscript>12</Subscript> micro-crystals

Highly ordered Bi₄Si₃O₁₂ micro-crystals were prepared at normal atmosphere. Phase identification of the prepared crystals was accomplished by X-ray diffractometer (XRD). Domain structure and defects were characterized by environmental scanning electron microscopy (ESEM). XRD shows that the obtained micro-crystals are of eulytite structure with chemical formulation of Bi₄Si₃O₁₂. A highly ordered growth pattern is confirmed due to the faster growth of the {124} faces than that of the {204} faces by ESEM. The growing process of the domain structure is of pollen parent and filial generation pattern. The filial generations of Bi₄Si₃O₁₂ crystals are generated from the pollen parent. Cracks generate from the defect areas and propagate along the {124} faces due to their lower binding energy under a proper temperature gradient, contributing to the total transcrystalline fracture. It is confirmed that the generation and development of the voids in the crystal grains can be developed when unmatched dimensions of the two opposite faces are formed. And the development of the voids is dependent on the dimensions and orientations of the two opposite faces. Supported by the Innovation Research Team Funds of Shaanxi University of Science & Technology (Grant No. SUST-A04)     

Molten Salt Synthesis of Ba（ Mgl／3Nb2／3 ）O3 Powder

The single-phrase Ba(Mgl/3Nb2/3)O3(BMN) powder was saccessfully prepared by the KCImolten salt synthesis(MSS) method. The temperature for single-phase BMN powders by MSS was about 400℃ lower than that by the solid-phase method. The average particle size (APS) was about 0.91,u.m at 900℃ and increased with increasing synhesis temperature. Based on the APS, the activation energy for particle growth in theMSS, whose value was 64. 1kJmol^-1.was attained. The sinterability of the powder prepared by MSS method wasbetter than that pretared by solid-phase method.     

Manufacture Process of 8Y2O3 Stabilized ZrO2 from Nano Powders

The manufacture process of 8 mol% Y2O3 stabilized ZrO2 ( YSZ ) from nano powders, including the forming and sintering stages, was studied. During the forming process of YSZ powders, the relative density of YSZ increases lineally with the forming press, and the sintering linear shrinkage of YSZ to the forming press compiles to the parabola trend. When the forming press exceeding 500MPa, the samples with lower shrinkage and high density were obtained. The sintering temperature of YSZ decreases greatly because of the small size and high active surface of YSZ powders. As a result, the beginning sintering temperature of YSZ made in the experiment is as low as 825℃, and the end sintering temperature is 1300-1350℃ . The relative density of YSZ ceramic by solid sintering at 1300-1350℃ is more than 97% , with little and small pores in the uniform microstructure.     

Surface organic modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

The surface organic modification of Fe3O4 nanoparticles with silane coupling reagent KH570 was studied. The modified and unmodified nanoparticles were characterized by FT-IR, XPS and TEM. The spectra of FT-IR and XPS revealed that KH570 was coated onto the surface of Fe3O4 nanoparticles to get Fe-O- Si bond and an organic coating layer also was formed. Fe3O4 nanoparticles were spheres partly with mean size of 18,8 nm studied by TEM, which was consistent with the result 17.9 nm calculated by Scherrer＇s equation. KH570 was adsorbed on surface and formed chemistry bond to be steric hindrance repulsion which prevented nanoparticles from reuniting. Then glycol-based Fe3O4 magnetic liquids dispersed stably was gained.     

Modification of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles by L-dopa or dopamine as an enzyme support

Fe3O4 magnetic nanoparticles were prepared by co-precipitation of Fe^2＋ and Fe^3＋ in an ammonia solution, and its size was about 36 nm measured by an atomic force microscope. Fe3O4 magnetic nanoparticles were modified by L-dopa or dopamine using sonication method. The analysis of FTIR clearly indicated the formation of Fe-O-C bond. Direct immobilization of trypsin （EC： 3.4.21.4） on Fe3O4 magnetic nanoparticles with L-dopa and dopamine spacer was investigated using glutaraldehyde as a coupling agent. No significant changes in the size and magnetic property of the three kinds of magnetic nanoparticles linked with or without trypsin were observed. The existence of the spacer molecule on magnetic nanoparticles could greatly improve the activity and the storage stability of bound trypsin through increasing the flexibility of enzyme and changing the microenvironment on nanoparticles surface compared to the naked magnetic nanoparticles.     

Nanocomposite films of V<Subscript>2</Subscript>O<Subscript>5</Subscript>−MoO<Subscript>3</Subscript> xerogel with poly ethylene oxide intercalation

Poly ethylene oxide (PEO)_x−V₂O₅−V₂O₅−MoO₃ (x=0, 0.5, 1) films were prepared by the sol-gel method. The synthesis and structure of the films were investigated by XRD, TG-DTA, FTIR, etc. The results show that V₂O₅−MoO₃ xerogel has a layered structure and its interlayer space increased from 1.3181 nm at x=0 to 1. 7898 nm at x=1 after the nanocomposite films were dried, and PEO in the interlayer changes the interface structure by forming hydrogen bonds with V=0 bands. CV measurement indicates that the intercalation of PEO improves insertion/extration properties of Li⁺ ions in the interlayer. ZHENG Jin-xia: Born in 1976 Funded by the National Natural Science Foundation of China (No. 50172036) and Natural Science Foundation of Hubei Province(No. 2001ABB083)     

Solvothermal preparation and thermoelectric properties of quasi-binary Sn(Pb) Te-Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript> compounds

Bulk samples of quasi-binary compounds in the Sn(Pb)Te-Bi₂Te₃ system were prepared by solvothermal method followed by a sintering procedure of compacted pellets. The formation mechanism of the precursor powders, microstructure and thermoelectric properties of the final bulk samples were studied.     

Fabrication and magnetic properties of Sm3(Fe,Ti)29Nx/α-Fe dual-phase nanocomposite permanent magnetic material

Sm3(Fe,Ti)29Nx/α-Fe dual-phase nanometer magnetic material was fabricated through rapid solidification, crystallization and nitridation of Sm-Fe (Ti) alloy. The effect of combination of rapid solidification and Ti alloy addition on the phase formation and microstructure of the Sm-Fe alloy is investigated in this paper. The microstructure of amorphous phase and dual-phase nano-grain crystals before and after crystallization annealing were observed using a high-resolution transmission electron microscope (HREM). The dual-phase nano-grains after annealing were compacted together with a clear interface with the direct exchange-coupling mechanism. Different annealing processes were used to examine the melt-spun alloy. Comparison of the images of SEM showed that annealing at 750℃ for 10 min was most suitable to get homogeneous and nano-grains. No obvious kink was detected in the second quadrant of the hysteresis loop like a single hard magnet, and strong exchange coupling was found between hard magnets and soft magnets.     

Formation of bulk ferromagnetic nanostructured Fe<Subscript>40</Subscript>Ni<Subscript>40</Subscript>P<Subscript>14</Subscript>B<Subscript>6</Subscript> alloys by metastable liquid spinodal decomposition

Nanostructured Fe₄₀Ni₄₀P₁₄B₆ alloy ingots of 3–5 mm in diameter could be synthesized by a metastable liquid state spinodal decomposition method. For undercooling ΔT > 260 K, the microstructure of the undercooled specimen had exhibited liquid state spinodal decomposition in the undercooled liquid state. The microstructure could be described as two intertwining networks with small grains dispersed in them. For undercooling ΔT > 290 K, the overall microstructure of the specimen changed into a granular morphology. The average grain sizes of the small and large grains are ≅ 30 nm and ≅ 80 nm, respectively. These prepared samples are soft magnets with saturation magnetization B _s ≅ 0.744 T. Supported by the Hong Kong Research Grants Council the National Natural Science Foundation of China (Grant No. 50861007) and Xinjiang University Doctoral Research Start-up Grant (Grant No. BS050102)     

Preparation and ferroelectric properties of Bi<Subscript>3.4</Subscript>Ce<Subscript>0.6</Subscript>Ti<Subscript>3</Subscript>O<Subscript>12</Subscript> thin films grown by sol-gel method

We have investigated the preparation and properties of Bi_3.4Ce_0.6Ti₃O₁₂ thin films. The Bi_3.4Ce_0.6Ti₃O₁₂ thin films were fabricated on the Pt/Ti/SiO₂/Si substrates using sol-gel method. The structure and morphology of the films were characterized using X-ray diffraction and atomic force microscopy. The thin films showed a perovskite phase and dense microstructure. The dielectric constant and the dissipation factor of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were about 172 and 0.031 at 1 kHz, respectively. The 2P _r and 2E _c of the Bi_3.4Ce_0.6Ti₃O₁₂ thin films were 67.1 μC/cm² and 299.7 kV/cm, respectively, under an applied field of 600 kV/cm. The Bi_3.4Ce_0.6Ti₃O₁₂ film did not show fatigue up to 4.46×10⁹ switching cycles at a frequency of 1 MHz, and showed good insulating behavior according to the test of leakage current. Supported by the Natural Science Foundation of Hubei Province (Grants No. 2004ABA082)