首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 156 毫秒
1.
采用自制电致发光测量装置测试了高直流电场作用下的聚对苯二甲酸乙二酯(PET)薄膜的光强和光谱.实验表明:PET的发光光强随所加电场而增大,在4.0 MV/cm附近发生预击穿,预击穿信号出现后,在450 nm和680 nm附近出现光谱带.  相似文献   

2.
硅烷交联聚乙烯的研究   总被引:4,自引:0,他引:4  
在双螺杆挤出机上进行了硅烷交联聚乙烯的研究,探讨了过氧化二异丙苯(DCP)、乙烯基三乙氧基硅烷(VTES)、二月桂酸二丁基锡(DBTDL)、水温以及聚乙烯种类对交联度的影响规律。发现交联度随DCP和VTES的用量增加而增大,当DCP和VTES的用量增加到一定程度时,交联度的增加程度已不明显;DBTDL和水温仅影响达到最大交联度的时间;在低密度聚乙烯(LDPE)、高密度聚乙烯(HDPE)、线形低密度聚乙烯(LLDPE)3种不同密度聚乙烯制得的交联料中,交联度由大到小的次序为LDPE>LLDPE>HDPE;采用HDPE/LLDPE为80/20的共混料可以得到交联度高达77%又综合性能优异的硅烷交联聚乙烯。  相似文献   

3.
以PVP为添加剂的BST薄膜制备与结晶性能   总被引:1,自引:0,他引:1  
用溶胶-凝胶法在Pt/Ti/SiO2/Si(100)基片上沉积Ba0.6Sr0.4TiO3薄膜,采用SEM、XRD、AFM分析薄膜的表面形貌和结晶行为。为抑制薄膜裂纹,在前驱体溶液中加入高分子聚合物聚乙烯吡咯烷酮(PVP)。结果表明,经700℃退火1h,得到表面平整、致密、无裂纹和孔洞以及晶粒取向高度一致的薄膜。薄膜钙钛矿结构明显,并随温度的升高而趋于完善。在结晶初期形成规则的柱状晶粒在长大和吞并的过程中逐渐形成颗粒状晶粒。薄膜的晶粒大小和表面粗糙度随退火温度的升高而增大。在平均晶粒较大且晶界分明的情况下,薄膜的均方根粗糙度仍能保持在7.854nm左右。  相似文献   

4.
采用紫外辐照技术制备了聚乙烯-马来酸酐接枝物,并用红外光谱对接枝物进行了表征.结果显示,马来酸酐(MAH)已经成功地接枝到了高密度聚乙烯(HDPE),低密度聚乙烯(LDPE),线性低密度聚乙烯(LLDPE)的分子链上,LLDPE和LDPE比HDPE显示了更高的接枝率.研究了紫外光辐照时间、单体及引发剂质量浓度等因素对接枝率及凝胶含量的影响.结果显示,接枝反应非常快,辐照30 s就达到最佳接枝效果.光引发剂二苯甲酮(BP)的用量对接枝率及凝胶含量有重要影响,BP的质量浓度过高可能引起严重的降解、交联等副反应,其质量分数为0.2%时最佳.体系的接枝率随MAH浓度的增加而提高.  相似文献   

5.
对聚乙烯液体包装薄膜生产过程中的成型工艺条件进行了分析说明.通过实践研究,解决了聚乙烯液体包装薄膜的热封性差,封口强度低的缺陷,并对如何提高保存期提出了建议  相似文献   

6.
碱催化制备溶胶-凝胶ZrO2薄膜及性能研究   总被引:1,自引:0,他引:1  
以Zr(OC3H7)4为前驱体,二甘醇为络合剂,在氨水的碱性条件下,水解制备ZrO2溶胶,并加入聚乙烯吡喏烷酮(PVP)来提高膜层的激光损伤阈值,提拉法涂膜.采用粘度、粒度分布、IR、DSC、XRD、AFM等测试手段对溶胶和薄膜性能进行表征.结果表明,ZrO2溶胶具有较好的粘度稳定性;薄膜表面均匀平整;ZrO2-PVP溶胶颗粒粒径分布比ZrO2溶胶的集中;ZrO2凝胶粉在329℃附近由非晶态转变为四方晶相结构,在600℃时已有单斜晶相结构出现,随温度的升高由四方晶相向单斜晶相结构转变;加入PVP能有效提高膜层的激光损伤阈值,ZrO2膜的激光损伤阈值为10.2 J/cm2(1064nm,1 ns),ZrO2-PVP膜的激光损伤阈值为14.17 J/cm2(1064nm,1ns).  相似文献   

7.
针对含氟聚酰亚胺薄膜透明度高但热膨胀系数大的问题,以4,4'-(六氟异丙烯)二酞酸酐(6FDA)为含氟二酐,4,4'-二氨基-2,2'-双三氟甲基联苯(TFMB)为原料,采用引入分子结构相对对称的刚性单体1,2,4,5-均苯四甲酸二酐(PMDA)进行共聚的方法合成了三种含氟比例不同的透明聚酰亚胺薄膜,编号为PI-1、PI-2、PI-3,作为对照,以PMDA和ODA(4,4-二氨基二苯醚)合成了PI-4,并对其性能进行了表征。热重分析表明,引入刚性单体共聚提高了含氟薄膜的热稳定性;介电测试显示,含氟薄膜的介电常数小于传统聚酰亚胺薄膜,PI-1的介电常数小于共聚薄膜PI-2和PI-3.;紫外-可见光谱图表明含氟聚酰亚胺薄膜的透光率明显大于传统薄膜,PI-1、PI-2、PI-3的截断波长分别为355 nm、360 nm和372 nm,黄色指数分别为6. 4、6. 9和8. 94,三种薄膜在波长500 nm处的透过率均超过90%;拉伸试验显示含氟聚酰亚胺薄膜的拉伸强度远低于传统聚酰亚胺,在添加部分刚性单体后,其力学强度有所增大;四种薄膜的热膨胀系数分别为14. 8×10~(-5)/℃、9. 9×10~(-5)/℃、5. 4×10~(-5)/℃和4. 0×10~(-5)/℃,随着PMDA含量的增加,薄膜的热膨胀系数明显降低。  相似文献   

8.
利用氢氧化钠/尿素/水溶液体系溶解纤维素,分别以不同的有机液体和无机溶液作为再生浴,制备出不同的再生纤维素薄膜,并在不同湿度条件下测试其电性能。结果表明:利用有机溶液作为再生浴制备的薄膜具有较小的介电常数和介电损耗,同时具有较大的击穿强度,高达162 MV/m;湿度越大,再生纤维素膜的介电常数和损耗越大,击穿强度减小。薄膜在90%RH下放置72 h,击穿强度只有15 MV/m。  相似文献   

9.
低密度聚乙烯可以改善聚碳酸酯的加工性能,并能在一定程度上改善机械性能 顺酐化乙丙橡胶对聚碳酸酯/低密度聚乙烯有增容作用,在聚碳酸脂/低密度聚乙稀体系中加入 1%左右即可使冲击强度增加 70 %  相似文献   

10.
制备出了聚并苯(PAS)和低密度聚乙烯/聚并苯复合物,探讨了辐射交联对低密度聚乙烯/聚并苯复合物室温电阻率和PTC/NTC效应的影响。低密度聚乙烯/聚并苯复合物经不同剂量辐照后,室温电阻率下降;PTC强度随辐照剂量的增加而增大,NTC强度随辐照剂量的增加而减小。  相似文献   

11.
A simple process to fabricate chain-like carbon nanotube (COT) films by microwave plasma-enhanced chemical vapor deposition (MPCVD) was developed successfully. Prior to deposition, the Ti/Al2O3 substrates were ground with Fe-doped SiO2 powder. The nano-structure of the deposited films was analyzed by scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectroscopy. The field electron emission characteristics of the chain-like carbon nanotube films were measured under the vacuum of 10-5 Pa. The low turn-on field of 0.80 V/μm and the emission current density of 8.5 mA/cm2 at the electric field of 3.0 Vμ/m are obtained. Based on the above results, chain-like carbon nanotube films probably have important applications in cold cathode materials and electrode materials.  相似文献   

12.
Metal hydroxides (MAH) consisting of magnesium hydroxide and aluminum hydroxide with a mass ratio of 1:2 were surface-modified by y-diethoxyphosphorous ester propyldiethoxymethylsilane, boric acid and diphenylsilanediol in xylene under dibutyl tin dilaurate catalyst at 140 ℃. Phosphorus, silicon and boron elements covalently bonded to metal hydroxide particles were detected by X-ray photoelectron spectroscopy. The degradation behavior of the surface-modified MAH was characterized by thermogravimetric analysis. The results show that linear low density polyethylene (LLDPE) composite, filled with 50% (mass fraction) of MAH modified by 5.0% (mass fraction) of modifiers, passes the V-0 rating of UL-94 test and shows the limited oxygen index of 34%, and its heat release rate and average effective heat combustion in a cone calorimeter measurement decrease obviously; The mechanical properties of MAH can be improved by surface-modification. The uniform dispersion of particles and strong interfacial bonding between particles and matrix are obtained.  相似文献   

13.
用傅里叶红外光谱仪研究了低密度聚乙烯 ( LDPE)、聚氯乙烯 ( PVC)、聚乙烯醇( PEA)树脂薄膜及添加普通玻璃粉和白云母粉的 L DPE薄膜红外吸收特性 ,对 6.8~ 1 3.7μm范围的上述薄膜的红外线平均透过率进行了比较。结果表明 :PEA对红外线的透过率最小 ,具有很好的保温性能 ;L DPE薄膜红外线透过率最高 ,保温性能最差 ,但通过添加玻璃粉或白云母粉 (添加物的质量分数 1 0 %为宜 ) ,能有效地降低其红外线透过率 ,提高保温性能 ,同时 ,玻璃粉的添加对提高 L DPE薄膜的可见光透过率更为有利。  相似文献   

14.
线性低密度聚乙烯马来酸酐溶液接枝反应的研究   总被引:1,自引:0,他引:1  
研究了在二甲苯溶剂中,以过氧化二苯甲酰为引发剂,线性低密度聚乙烯接枝马来酸酐的反应.采用正文实验方法考察了引发剂用量、单体及聚乙烯浓度、反应温度及时间、阻止交联剂的加入量等因素对接枝反应的影响。结果表明各因素对聚乙烯接枝率影响的大小次序是:MAH用量,反应温度,阻止交联剂用量,LLDPE浓度和引发剂BPO用量.阻止交联剂的加入可以有效地防止聚乙烯活性自由基的交联。  相似文献   

15.
Diamond films were deposited on high-speed steel substrates by hot filament chemical vapor deposition (HFCVD) method. To minimize the early formation of graphite and to enhance the diamond film adhesion, a WC-Co coating was used as an interlayer on the steel substrates by high velocity oxy-fuel spraying. The effects of methane content on nucleation, quality, residual stress and adhesion of diamond films were investigated. The results indicate that the increasing methane content leads to the increase in nucleation density, residual stress, the degradation of quality and adhesion of diamond films. Diamond films deposited on high-speed steel (HSS) substrate with a WC-Co interlayer exhibit high nucleation density and good adhesion under the condition of the methane content initially set to be a higher value (4%, volume fraction) for 30 min, and then reduced to 2% for subsequent growth at pressure of 3 kPa and substrate temperature of 800 °C.  相似文献   

16.
研制了具有静电感应三极管结构的有机电致发光三极管,用有机半导体酞菁铜和有机发光材料喹啉铝蒸发膜为作用层,其结构为金/酞菁铜/铝/酞菁铜/喹啉铝/ITO透明电极/玻璃基板.测试了其基本电、光学特性.由测试结果可知,较低的栅极偏压可控制由源极注入到喹啉铝发光层的载流子.通过合理设计、控制制作梳状铝栅极结构,获得了高速、大电流驱动等良好工作特性.  相似文献   

17.
以液体石蜡为碳源,对采油菌株Bacillus FH-1-2进行好氧和兼性厌氧培养。通过测定培养过程中发酵液的表面张力、菌体密度、pH值以及细胞疏水性,发现好氧和兼性厌氧培养过程中各项指标的变化趋势相近,兼性厌氧条件下的生长较慢;细胞疏水性和发酵液pH值均无显著变化;发酵液接近中性,有利于菌体生长。结果表明,细胞疏水性强能促进菌体生长。对数生长期发酵液的表面张力随菌体密度的增大而减小,在菌体生长的稳定期和衰亡期,发酵液的表面张力和菌体密度正相关。兼性厌氧培养更有利于菌株Bacillus FH-1-2应用于原油采收。  相似文献   

18.
为了获得新型HiPIMS稳定放电及制备优质膜层时的最优外部磁场参数,研究外部磁场变化对电-磁场协同增强高功率脉冲磁控溅射((E-MF)HiPIMS)放电及沉积特性的调制过程。在其他工艺参数保持不变的情况下,研究了外部磁场(线圈电流)对HiPIMS钒(V)靶放电规律以及V膜微观结构和性能的影响。采用数字示波器监测HiPIMS放电行为,利用XRD、SEM、AFM、摩擦磨损试验机及电化学腐蚀法等表面分析方法,研究V膜相结构、表面形貌、截面形貌、耐摩擦磨损性能及耐腐蚀性能等沉积特性。结果表明:随线圈电流的增加,基体离子电流密度逐渐增加,当线圈电流为6 A时基体离子电流密度最高可达209.2 mA/cm~2。V膜的相结构仅为V(111)但其晶面衍射峰强度随线圈电流的增加而逐渐增加。V膜表面呈现出典型的圆凹坑状形貌特征,其表面粗糙度先减小后增大且最小仅为10 nm。当线圈电流(4 A)较低时V膜生长表现为致密细小的晶体生长结构,膜层沉积速率随着线圈电流的增加而增加。当线圈电流为4 A时,V膜样品的摩擦系数最小、耐磨性最优,同时V膜样品具有最好的耐蚀性。  相似文献   

19.
A thermogravimetric analysis (TG) was conducted to study the thermal decomposition behavior and kinetics of composites from coal and high density polyethylene (HDPE), linear low density polyethylene (LLDPE) or low density polyethylene (LDPE). The results show that coal facilitates melting of the polyethylene before temperatures reach 700 K in nitrogen due to the exothermic effect of coal. Above 700 K, adding coal into the polyethylene will result in smaller maximum rates of mass loss and higher initial mass loss temperatures of the composites. Hence, some chemical interactions, occurring between liquid compounds released in the pyrolysis of the coal and polymer, depend on several factors, such as coal rank and the molecular structure of polymers. Synergetic effects in coal and polymers were also found. Both chemical interactions and synergetic effects control the entire thermal decomposition behavior of composites. The larger the amount of coal in the composites, the greater the decomposition temperature spans and the higher the maximum decomposition temperature, the smaller the devolatilization rates. The effect of coal on the thermal stability of composites lies in the hydrogen acceptor effect of the coals. Thermal decomposition of the coals, the polymers and related composites can be modelled via first order parallel reactions between 563 K and 763 K.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号