Synthesis and Piezoelectric Properties of Lead-free （ Bi0.5 Na0.5 ）1-x（BaaSrb）xTiO3 Ceramics

A new group of lead-free piezoelectric ceramics,（Bi0.5 Na0.5）1-x（BaaSrb）xTiO3（abbreviated as BNBST[100x-100a/100b],0〈x〈1,a＋b=1）,was synthesized.The ceramics were prepared by conventional ceramic sintering technique,and the ceramics with density of 95% of the theoretical one can be sintered without the atmosphere control during the sintering process.The results of the X-ray diffraction（XRD） data show that the ceramics possess a single perovskite phase.The measurements of dielectric and piezoelectric properties reveal that the ceramics provide relatively high piezoelectric charge constant d33 and high planar electromechanical coupling factor kp.For the BNBST6-95/5 ceramics,d33 is equal to 170pC/N,and kp is equal to 32.0%.The fabrication technique for these ceramics is conventional and stable.     

(Na_(0.5)K_(0.5))NbO_3基无铅压电陶瓷压电常数的研究

针对目前无铅压电陶瓷的压电常数d33偏小的情况,采用传统的烧结方法制备了(Na0.5K0.5)NbO3基无铅压电陶瓷(Na0.5K0.45Li0.05)Nb0.95-xSbxTa0.05O3(x=0.03,0.06,0.09,0.12),研究了在Li和Ta含量固定的情况下,Sb元素的添加量和烧结温度对陶瓷的压电常数的影响.研究结果表明,适量Sb元素的掺杂可以大幅度提高陶瓷的压电常数d33,陶瓷样品的压电常数d33随着Sb含量的增加先增大后减小.烧结温度可以影响陶瓷的密度,进而影响其压电常数.在1130℃的最佳烧结温度下,Sb含量x=0.09时,陶瓷样品表现出最佳的压电性能,压电常数d33=328 pC/N.     

La2O3掺杂对(Bi1/2Na1/2)0.94Ba0.06TiO3陶瓷性能与微结构的影响

采用传统陶瓷工艺方法制备了La2O3掺杂(Bi1/2Na1/2)0.94Ba0.06TiOa(BNBT6)无铅压电陶瓷,系统地研究了La2O3掺杂对该体系陶瓷介电、压电性能与微观结构的影响.结果表明:该体系具有很高的压电常数,是单一的钙钛矿结构,La2O3的添加对晶粒生长具有一定的抑制作用,线收缩率和相对密度增大.室温介电常数随着La2O3掺杂量的增加而增大.与不添加La2O3的陶瓷样品相比,添加少量La2O3可以使体系的弛豫特征更为明显.当掺杂量为0.1 wt%时,该体系陶瓷具有较好的综合性能:d3a=160 pC/N,kp=0.322.当掺杂量达到0.5 wt%以后,陶瓷的压电性能严重降低.     

Microstructures and Electrical Properties of Bi_(0.5)-(Na_(1-x-y)K_xLi_y)_(0.5)TiO_3 Lead-free Piezoelectric Ceramics

The microstructures and electrical properties of Bi0.5(Na1-x-yKxLiy)0.5TiO3 lead-free piezoelectric ceramics were studied.These ceramics were prepared by conventional ceramic technique.XRD analysis reveals that the ceramics possess almost pure perovskite phase when y≤0.2.The SEM results show that,with more amounts of Li+,the crystalline grain growing speed is accelerated,and the sintering temperature can effectively be decreased.The measurements of piezoelectric properties indicate that the ceramics with relatively low amount of Li+ and high amount of K+ have comparatively large piezoelectricity.The dielectric measurements show that the ceramics have properties like relaxor ferroelectrics and diffuse phase transition(DPT) at Td and Tc,respectively.The results of ferroelectric measurements reveal the system has relatively higher remanent polarization Pr(27.6 μC/cm2) and lower coercive field Ec(37.5 kV/cm).     

Microstructure, crystalline phase and electrical properties of Li0.06（Na0.5K0.5）0.94Nb（1-2x/5）MgxO3 lead-free piezoelectric ceramics

MgO-modified Li0.06(Na0.5K0.5)0.94NbO3(L6NKN) lead-free piezoelectric ceramics were synthesized by normal sintering at a relatively low temperature of 1000°C.The crystalline phase,microstructure,and electrical properties of the ceramics were investigated with a special emphasis on the influence of MgO content.The addition of MgO effectively improves the sinterability of the L6NKN ceramics.X-ray diffraction analysis indicates that the morphotropic phase boundary(MPB) separating orthorhombic and tetragonal ph...     

Effects of Excess Barium on the Structure and Electrical Properties of(Ba,Ca)TiO_3 Piezoelectric Ceramics with High Mechanical Quality Factors

Manganese-doped Ba_(0.925)Ca_(0.075)TiO_3 lead-free piezoelectric ceramics(abbreviated as BCT)with high mechanical quality factor were synthesized by conventional solid-state reaction method.The effects of excess Ba on the crystal structure,microstructure,and electrical properties of the ceramics were systematically investigated.X-ray diffraction and Raman spectra revealed that Ca~(2+)ions were pushed from Ba sites to Ti sites of BCT when 1.5 mol%extra Ba~(2+)ions were added after sintering.The grain size of the ceramics was decreased by adding extra Ba~(2+)ions.The mechanical quality factor and resistivity of the ceramics decreased dramatically when the excess Ba was more than 1.5 mol%.High piezoelectric coefficients(d_(33)=150-190 pC/N)and high mechanical quality factors(Q_m=1 000-1 200)were obtained in the ceramics when the excess of Ba was between 0.5 mol%and 1 mol%.These results indicated that the properties of BCT ceramics could be tailored by adjusting the content of Ba.     

Effect of Li content on the microstructure and properties of lead-free piezoelectric （K0.5Na0.5）1-xLixNbO3 ceramics prepared by SPS

Lead-free piezoelectric （K0.5sNa0.5）1-xLixNbO3 （x = 0at%-20at%） ceramics were synthesized by spark plasma sintering （SPS） at low temperature and the effects of LiNbO3 addition on its crystal structure and properties were also studied. When the Li content was less than 6at%, a single proveskite phase with the similar structure of （K0.5Na0.5）NbO3 was formed; and a secondary phase with K3Li2Nb5O15 structure was observed in the 6at% 〈 x 〈 20at% compositional range. Furthermore, LiNbO3 existed as the third phase when the Li content was higher than 8at%. The grain sizes increased from 200-500 nm to 5-8 μm when the K3Li2Nb5O15 and LiNbO3 like phases were formed. With increasing Li content, the relative density of the ceramics first decreased from 97% to 93% and then kept constant. The piezoelectric coefficient d33, dielectric constant, and planner electromechanical coupling factor exhibited a decreasing tendency with increasing Li content because of the decrease in density and the formation of the secondary phase such as K3Li2Nb5O15 and LiNbO3. The formation of dense microstructure with a single phase is necessary in improving the properties of the （K0.5Na0.5）1-xLixNbO3 ceramics.     

二次烧结对KNN-LS-Bi(Mg0.5Ti0.5)O3无铅压电陶瓷性能的影响

采用传统固相烧结法和二次烧结工艺制备了xBi(Mg0.5Ti0.5)O3-0.95K0.5Na0.5NbO3-0.05LiSbO3(xBMT-KNN-LS)无铅压电陶瓷,研究了二次烧结工艺对xBMT-KNN-LS陶瓷性能的影响。结果表明:采用传统的陶瓷烧结工艺所得到的性能为压电常数d33=220 pC/N、平面机电耦合系数kp=39.6%、介电损耗tanδ=6.38%。而采用二次陶瓷烧结工艺得到的最佳性能为d33=254 pC/N、kp=37.8%、tanδ=4.81%,因此,二次烧结对该体系的压电性能有显著的影响。     

Effect of doped Mn on piezoelectric properties of (Na_(0.5)Bi_(0.5))_ (0.92)Ba_(0.08)TiO_3 lead-free ceramics

1INTRODUCTION Therehasbeengreatinterestinthestudiesof thelead freematerialswithdielectric,piezoelectricandferroelectricpropertiesinthefieldoffunction almaterialsfortheiramiabilitytoenvironment. (Na1/2)TiO3(NBT)ceramicshavebeenwidelystudiedbecauseoftheirrelativelylargeremnant polarization(Pr)of38μC/cm2andcoercivefieldof 73kV/cm[1].However,NBTcannotreplacelead zirconatetitanate(PZT)basedceramicsbecausethepiezoelectricpropertiesofNBTarestillnot comparabletothoseofPZT[24].Recently,m…     

Na_(0.5)K_(0.5)NbO_3织构化陶瓷制备与表征

采用凝固法制备出各向异性的片状钛酸钡作为模板,利用模板晶粒生长(TGG)法制备出Na0.5K0.5NbO3(NKN)织构化陶瓷.研究了NKN织构化陶瓷的工艺、组织和性能.研究结果表明,钛酸钡可以作为NKN陶瓷的模板,在陶瓷烧结过程中诱导NKN晶粒的生长,模板的取向决定了NKN陶瓷晶粒取向,随着烧结温度的升高陶瓷的压电性能(d33)达到69 pC/N,在合理的烧结工艺下得到了取向比较明显的织构化陶瓷.     

钡钙锶共掺杂钛酸铋钠无铅压电陶瓷的制备及性能

采用溶胶-凝胶法制备工艺制备了（1-x）（Na0.5Bi0.5）TiO3-xBa0.092Ca0.03Sr0.05TiO3（x=0.04、0.06、0.07、0.08）系无铅压电陶瓷。研究了陶瓷的铁电、压电性能和显微结构。结果表明,该体系陶瓷在x=0.06时,其压电常数d33,机电耦合系数kp,厚度耦合系数kt,相对介电常数rε,介质损耗tgδ,分别为152,0.24,0.47,1 250,0.04。     

（0.82-x）Bi0.5Na0.82Ti O3-0.18Bi0.5K0.18TiO3-xBiFeO3（x=0.01-0.07）无铅压电陶瓷的制备及其电学性能的研究

采用传统的固相烧结法于1120℃烧结2 h得到（0.82-x）Bi0.5Na0.82Ti O3-0.18Bi0.5K0.18TiO3-xBiFeO3（x=0.01-0.07）无铅压电陶瓷,并对该体系陶瓷的微观结构和电学性能进行了研究。结果表明,BiFeO3的引入量x为0.01-0.07时,样品均为具有MPB准同型相界（三方相和四方相共存）的钙钛矿结构。BiFeO3的引入使陶瓷的晶粒度略有增加;当x=0.03时,样品达到最大致密度。为97.7%;陶瓷的压电常数d33随BiFeO3的引入而降低。陶瓷的相对介电常数εr和居里温度随BiFeO3的引入而明显增大,在x=0.03时达到最大值。     

Relationship between Liquid Phase Content and the Orientation of PMNT Ceramics by TGG Method

The effects of glass frit on the sintering and electric properties of PMN-PT textured ceramics were investigated. The glass frits, including PbO, Bi2O3 and ZnO, were selected since liquid phase sintering lowered the PMN-PT sintering temperature. The piezoelectric properties of PMN-PT ceramics with glass frit addition are strongly dependent on the densification. The addition of glass frits into PMN-PT matrix reduced the sintering temperature to 1 100 ℃ instead of 1 150 ℃ for samples without glass. The piezoelectric coefficients (d33) of PMN-PT textured ceramics achieved 568 pc/N with 1 wt% excess PbO.     

Zn_(1/3)Nb_(2/3)含量对xPMnS-(1-x)PZN性能的影响

以xPMnS-(1-x)PZN四元系压电陶瓷为研究对象,通过研究Zn1/3Nb2/3含量的变化对0.5PMnS-0.5aPZN材料结构与性能的影响,获得具有高压电活性的0.5PMnS-0.5aPZN陶瓷材料。结果表明,四方相结构的0.5PMnS-0.5aPZN材料压电活性优于三方相结构,性能最好的组成位于MPB(四方相边界)附近靠近四方相含量较高的区域,组成Zn1/3Nb2/3含量的变化影响了MPB的位置。     

0．992K0．5Na0．5NbO3-0．008BiFeO3无铅压电陶瓷制备及压电性能研究

以水热法制备的0．992K0．5Na0．5NbO3（BF）粉体等为原料,采用常压烧结法在1065℃下烧结2h制备了0．992K0．5Na0．5NbO3-0．008BiFe03无铅压电陶瓷,并研究了BiFeO3掺杂对0．992K0．5Na0．5NbO3-0．008BiFeO3无铅压电陶瓷结构和压电的影响．研究结果表明：BiFeO3掺杂使K0.5Na0.5NbO3无铅压电陶瓷正交相减弱,晶粒尺寸由6／2m减小到1μm;压电性能有一定提高,压电常数（d33）、机电耦合系数（kp）分别达到120pC／N和37．8,居里温度Tc由444．4℃减少至420．6℃．     

Struchre and Electrical Properties of (Na0.5Bi0.5)0.94Ba0.06TiO3 Ceramic with 0.5 wt% of MnO

The structure and electrical properties of(Na0.5Bi0.5)0.94Ba0.06TiO3 ceramic doped with 0.5 wt% of MnO were investigated in comparison with those of(Na0.5Bi0.5)0.94Ba0.06TiO3 ceramic.It was ascertained that the MnO addition did not cause remarkable change in crystal structure and microstructure.The MnO addition mainly displayed a hard effect on the electrical properties,an increase of coercive field(Ec)and mechanical quality factor(Qm)together with a decrease of dielectric constant(?r)and piezoelectric constant(d33).An enhancement of electromechanical coupling factor(kp)with the MnO addition was obtained too.An essential relation between the piezoelectric properties and ferroelectric nature of the ceramics was detected.It was found that the piezoelectric properties of the ceramics highly depended on the corporative contribution of remanent polarization(Pr)and coercive field.     

Effect of doped Mn on piezoelectric properties of （Na0.5Bi0.5 ）0.92 Ba0.08 TiO3 lead-free ceramics

Piezoelectric ceramics (Na0.5Bi0.5)0.92Ba0.05TiO3 x%MnCO3(BNBT-Mn, x=0-1.6,mass fraction)were synthesized by conventional solid state reaction. The results show that when the addition of MnCO3 is 0-1.4%, BNBT-Mn ceramics exhibit a single-phase perovskite structure. With the increase of content of MnCO3, piezoelectric constant and electromechanical coupling factor increase rapidly when x is lower than 0.3. Then they both decrease when x is in the range of 0.3 and 1.6. When x=0.3, piezoelectric constant and electromechanical coupling factor reach the maximum value of 160 pC/N and 58.5% respectively, which can improve the temperature stability of BNBT-Mn.     

Effects of Excess Barium on the Structure and Electrical Properties of (Ba,Ca)TiO<Subscript>3</Subscript> Piezoelectric Ceramics with High Mechanical Quality Factors

Manganese-doped Ba_0.925Ca_0.075TiO₃ lead-free piezoelectric ceramics (abbreviated as BCT) with high mechanical quality factor were synthesized by conventional solid-state reaction method. The effects of excess Ba on the crystal structure, microstructure, and electrical properties of the ceramics were systematically investigated. X-ray diffraction and Raman spectra revealed that Ca²⁺ ions were pushed from Ba sites to Ti sites of BCT when 1.5 mol% extra Ba²⁺ ions were added after sintering. The grain size of the ceramics was decreased by adding extra Ba²⁺ ions. The mechanical quality factor and resistivity of the ceramics decreased dramatically when the excess Ba was more than 1.5 mol%. High piezoelectric coefficients ( d₃₃ = 150–190 pC/N ) and high mechanical quality factors ( Q_m = 1 000–1 200 ) were obtained in the ceramics when the excess of Ba was between 0.5 mol% and 1 mol%. These results indicated that the properties of BCT ceramics could be tailored by adjusting the content of Ba.     

不同铅气氛对PMSZT压电陶瓷机电性能的影响

采用固相烧结法制备了三元系压电陶瓷Pb0.98Sr0.02（Mn1/3Sb2/3）x（Zr0.5Ti0.5）1-xO3（0%〈x〈0.1）（PMSZT）,研究了铅气氛和非铅气氛保护条件烧结对其相结构、微观结构、介电性能以及压电性能的影响．实验结果表明：在烧结温度1100-1300℃范围内,铅气氛保护烧结的试样其综合性能优于非铅气氛保护烧结的试样．铅气氛保护条件下于1200℃得到最佳性能：εr=1717、d33=301、Kp=0．55、tanδ=0．42％、Qm=1453．     

二步烧结法制备SCNN陶瓷及其性能

在传统工艺设备制备的基础上,运用二步烧结法制备出钨青铜结构压电陶瓷Sr2-xCaxNaNb5O15(SCNN),通过对x=0.05～0.30的陶瓷研究,获得了具有较高压电系数(80pC/N)和介电常数(>1600)的SCNN陶瓷.X线衍射实验及扫描电镜实验的结果表明,该陶瓷具有极高的致密性.