A new single‐phase high‐power‐factor converter with buck and buck–boost hybrid operation

In recent years, a wide variety of high‐power‐factor converter schemes have been proposed to solve the harmonic problem. The schemes are based on conventional boost, buck, or buck–boost topology, and their performance, such as output voltage control range in the boost and buck topology or efficiency in the buck–boost topology, is limited. To solve this, the authors propose a single‐phase high‐power‐factor converter with a new topology obtained from a combination of buck and buck–boost topology. The power stage performs the buck and buck–boost operations by a compact single‐stage converter circuit while the simple controller/modulator appropriately controls the alternation of the buck and buck–boost operation and maintains a high‐quality input current during both the buck and buck–boost operations. The proposed scheme results in a high‐performance rectifier with no limitation of output voltage control range and a high efficiency. In this paper, the principle and operation of the proposed converter scheme are described in detail and the theory is confirmed through experimental results obtained from 2‐kW prototype converter. © 2000 Scripta Technica, Electr Eng Jpn, 131(3): 91–100, 2000     

A single‐phase buck‐boost PFC converter with output‐voltage,ripple‐reducing operation

This paper describes a new single‐phase buck‐boost power‐factor‐correction (PFC) converter with output‐voltage, ripple reducing operation. The converter consists of a conventional buck‐boost PFC converter and an additional switch to obtain a freewheeling mode of the dc inductor current, and is operated by two modulators. The first modulator controls the buck‐boost switch to obtain PFC. The other modulator controls the square value of the instantaneous dc inductor current to perform the output‐voltage‐ripple‐reducing operation. In the two modulations, the time integral value of the input and output currents in each modulation period are controlled directly and indirectly, respectively. Thus, modulation errors or undesirable distortions of the input current and output voltage ripple are eliminated even if the dc inductor current produces large ripple in a low‐frequency range. The theories and combination techniques for the two modulators, implementation, and experimental results are described. © 1998 Scripta Technica, Electr Eng Jpn, 126(2): 56–70, 1999     

A new topology for nonisolated multiport zero voltage switching dc‐dc converter

In this paper, a new multiport zero voltage switching dc‐dc converter is proposed. Multiport dc‐dc converters are widely applicable in hybrid energy generating systems to provide substantial power to sensitive loads. The proposed topology can operate in 3 operational modes of boost, buck, and buck‐boost. Moreover, it has zero voltage switching operation for all switches and has the ability to eliminate the input current ripple; also, at low voltage side, the input sources can be extended. In addition, it has the ability of interfacing 3 different voltages only by using 3 switches. In this paper, the proposed topology is analyzed theoretically for all operating modes; besides, the voltage and current equations of all components are calculated. Furthermore, the required soft switching and zero input currents ripple conditions are analyzed. Finally, to demonstrate the accurate performance of the proposed converter, the Power System Computer Aided Design(PSCAD)/Electro Magnetic Transient Design and Control(EMTDC) simulation and experimental results are extracted and presented.     

High‐efficiency transformerless buck–boost DC–DC converter

A novel high‐efficiency transformerless buck–boost DC–DC converter is proposed in this paper. The presented converter voltage gain is higher than that of the conventional boost, buck–boost, CUK, SEPIC and ZETA converters, and high voltage gain can be obtained with a suitable duty cycle. The voltage stress across the power switch is low. Hence, the low on‐state resistance of the power switch can be selected to decrease conduction loss of the switch and improve efficiency. The input current ripple in the presented converter is low. The principle of operation and the mathematical analyses of the proposed converter are explained. The validity of the presented converter is verified by the simulation results in PSCAD/EMTDC software and experimental results based on the prototype circuit with 250 W and 40 kHz. Copyright © 2017 John Wiley & Sons, Ltd.     

Output current ripple reduction of LED driver using ceramic‐capacitor‐input circuit and buck‐boost converter

This article proposes an LED driver that consists of a ceramic‐capacitor‐input rectifier and a buck‐boost converter. The LED driver has an advantage of long life because it does not contain any electrolytic capacitors. However, the issue with electrolytic capacitor‐less LED driver is that the ripple of the smoothed voltage becomes large due to insufficient capacitance of the smoothing capacitor. The proposed method, which uses the discontinuous current mode of a buck‐boost converter, reduces the output current ripple under such conditions. Experimental results using a 5.7 W LED driver prototype demonstrate that the proposed method reduces the output current ripple and that the percent flicker becomes 4.4%, which is smaller than the recommended upper limit of 8%.     

Analysis and implementation of a step–up power converter with input current ripple cancelation

This paper proposes a power electronics converter capable of canceling the input current ripple at preselected duty cycle. The proposed converter is an extended topology of a buck–boost converter aided by a boost‐type converter that improves the quality of the current drawn from the direct current source. The voltage gain of the proposed converter is increased as well, with a minimum of extra component added to the original buck–boost power converter. These features make the proposed converter ideal for low voltage generation sources, such as photovoltaic panel and fuel cell applications. Along this paper, the state space mathematical model is developed to provide the key design guidelines. The theoretical analysis is validated through computer simulation and hardware prototyping.     

A new interleaved bidirectional dc/dc converter with zero voltage switching and high voltage gain: analyses,design and simulation

In this paper, a new interleaved non‐isolated bidirectional dc–dc converter with capability of zero voltage switching and high voltage gain is proposed. In the proposed converter by using two coupled inductors and one capacitor, the voltage gain is extended. Moreover, by using only an auxiliary circuit that includes an inductor and two capacitors, the zero voltage switching (ZVS) of two used switches in the first phase of converter can be achieved. The ZVS operation of two used switches in the second phase is always obtained without using any extra auxiliary circuit. This converter similar to other interleaved converters has low input current ripple and low current stress on switches. In this paper, the proposed converter is analyzed in all operating modes, and also the voltage gain, required conditions for ZVS operation of switches, voltage and current stresses of all switches, and the value of input current ripple in both boost and buck operations are obtained. Finally, the accuracy performance of the proposed converter is verified through simulation results in EMTDC/PSCAD software. Copyright © 2017 John Wiley & Sons, Ltd.     

A new non‐isolated free ripple input current bidirectional DC‐DC converter with capability of zero voltage switching

In this paper, a new nonisolated free ripple input current bidirectional dc‐dc converter with capability of zero voltage switching (ZVS) is proposed. The free ripple input current condition at low voltage side is achieved by using third winding of a coupled inductor and a capacitor for the whole range of duty cycles. In the proposed structure, the voltage conversion ratio can be more increased by adding the turn ratio of the second winding of the coupled inductor for the whole range of duty cycles. By adjusting the value of an auxiliary inductor in the topology of the converter, according to the power, the ZVS operation of the implemented 2 switches can be achieved throughout the whole power range. The mentioned features of proposed converter are validated theoretically for both boost and buck operations. In this paper, the proposed converter is analyzed for all operating modes. Moreover, all equations of the voltages and currents of all components, voltage conversion ratio, the required conditions for ZVS operation of switches, and also required conditions for canceling input current ripple at low voltage side are obtained. Finally, the performance of the proposed converter is reconfirmed through experimental and EMTDC/PSCAD simulation results.     

High‐power‐factor single‐switch AC to DC converter for LED lighting

In this paper, we report a novel single‐switch AC to DC step‐down converter suitable for light emitting diodes. The proposed topology has a buck and a buck–boost converter. The circuit is designed to operate in the discontinuous conduction mode in order to improve the power factor. In this topology, a part of the input power is connected to the load directly. This feature of the proposed topology increases the efficiency of power conversion, improves the input power factor, produces less voltage stress on intermediate stages, and reduces the output voltage in the absence of a step‐down transformer. The theoretical analysis, design procedure, and performance of the proposed converter are verified by simulation and experiment. A 36 V, 60 W prototype has been built to demonstrate the merits of this circuit. © 2017 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.     

Single‐stage single‐switch PFC converter for wide‐input extreme step‐down voltage applications

This paper presents a new single‐stage single‐switch high power factor correction AC/DC converter suitable for low‐power applications (< 150 W) with a universal input voltage range (90–265 V_rms). The proposed topology integrates a buck–boost input current shaper followed by a buck and a buck–boost converter, respectively. As a result, the proposed converter can operate with larger duty cycles compared with the existing single‐stage single‐switch topologies, hence, making them suitable for extreme step‐down voltage conversion applications. Several desirable features are gained when the three integrated converter cells operate in discontinuous conduction mode. These features include low semiconductor voltage stress, zero‐current switch at turn‐on, and simple control with a fast well‐regulated output voltage. A detailed circuit analysis is performed to derive the design equations. The theoretical analysis and effectiveness of the proposed approach are confirmed by experimental results obtained from a 100‐W/24‐V_dc laboratory prototype. Copyright © 2011 John Wiley & Sons, Ltd.     

A novel active‐clamp zero‐voltage‐switching buck‐boost converter

An active‐clamp zero‐voltage‐switching (ZVS) buck‐boost converter is proposed in this paper to improve the performance of converter in light load condition. By employing a small resonant inductor, the ZVS range of switches could be adjusted to very light load condition. Moreover, 2 clamping capacitors are added in the converter to eliminate the voltage spike on the switches during transition. The operating principle of the proposed converter is analyzed, and the optimal design guide for full range ZVS is also provided. A 60‐W output prototype is experimentally built and tested in laboratory to verify the feasibility of proposed converter. The measured results show the critical ZVS operation of power switches at 1 and 0.7‐W output power for buck and boost mode, respectively. The peak conversion efficiency is up to 92.3%.     

Improved control‐to‐output characteristics of a PWM buck‐boost converter

An indirect control variable for improving the control‐to‐output characteristics of a Pulse Width Modulation (PWM) buck‐boost converter is introduced in this letter. The voltage gain and the small‐signal model of the buck‐boost converter are reviewed. The actual voltage command at one input of the PWM comparator is from the proposed indirect control variable and the peak value of the high‐frequency PWM carrier. The resulted voltage gain function appears proportional to this indirect control command. Also the dependence of the DC gain of the control‐to‐output transfer function on the duty cycle is eliminated. Experimental results conform well to the theoretical analysis. Copyright © 2010 John Wiley & Sons, Ltd.     

Analysis and implementation of a high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter

A high‐efficiency zero‐voltage‐zero‐current‐switching DC–DC converter with ripple‐free input current is presented. In the presented converter, the ripple‐free boost cell provides ripple‐free input current and zero‐voltage switching of power switches. The resonant flyback cell provides zero‐voltage switching of power switches and zero‐current switching of the output diode. Also, it has a simple output stage. The proposed converter achieves high efficiency because of the reduction of the switching losses of the power switches and the output diode. Detailed analysis and design of the proposed converter are carried out. A prototype of the proposed converter is developed and its experimental results are presented for validation. Copyright © 2011 John Wiley & Sons, Ltd.     

A power efficient buck‐boost converter by reusing the coil inductor for wireless bio‐implants

In this paper, a buck‐boost converter circuit for wireless power transfer via inductive links in bio‐implantable systems is presented. The idea is based on reusing the power receiver coil to design a regulator. This method employs five switches to utilize the coil inductor in a frequency other than the power‐receiving signal frequency. Reusing the coil inductor decreases the on‐chip regulator area and makes it suitable for bio‐implants. Furthermore, in the proposed technique, the regulator efficiency becomes almost independent of the coil receiving voltage amplitude. The proposed concept is employed in a buck‐boost regulator, and simulation results are provided. For a 10 MHz received signal with the amplitude variation within 3 ~ 6 V and with the converter switching rate of 200 kHz, the achieved maximum efficiency is 78%. The proposed regulator can also deliver 10 μA to 4 mA to its load while its output voltage varies from 0.6 to 2.3 V. Simulations of the proposed converter are performed in Cadence‐Spectre using TSMC 0.18 μm CMOS technology. Copyright © 2017 John Wiley & Sons, Ltd.     

Performance analysis and calculation of critical inductance and output voltage ripple of a simple non‐isolated multi‐input bidirectional DC‐DC converter

In this paper, a simple non‐isolated multiple input (MI) bidirectional DC‐DC topology is proposed which can operate in buck, boost, or buck‐boost modes. The proposed topology utilizes a battery pack to realize the bidirectional power flow operation especially when the input sources are non‐storable ones. The excess energy of input sources can be stored in the battery and be injected to the load, when required. Simultaneous or independent power transfer of input sources is also provided. For better evaluation, the proposed topology has been compared with several recently presented novel topologies, from view point of number of inductors, capacitors, switches, and diodes. Comparison results show that the proposed topology utilizes less number of components (switches, inductors, capacitors, and current sensors) which can reduce the size, cost, and complexity of converter. Different operational modes of the proposed topology (unidirectional buck, boost, buck‐boost modes, and bidirectional mode) have been presented. Also, boost mode of the proposed topology has been investigated in detail, from design point of view, and generalized relationships have been proposed for calculation of critical inductance (CI) and output voltage ripple (OVR) of proposed n‐input boost topology. To validate proposed theoretical concepts, the proposed topology has been modeled and simulated in PSCAD/EMTDC software, and the 3‐input boost version has been experimentally implemented. Simulation and experimental results confirm appropriate performance of the proposed topology.     

Design and implementation of a digitally controlled single‐inductor dual‐output (SIDO) buck converter

This paper describes design and implementation of a digitally controlled single‐inductor dual‐output (SIDO) buck converter operating in discontinuous conduction mode. This converter adopts time‐multiplexing control in providing two independent output voltages using only an inductor. The design issues of the digital controller are discussed, including static and dynamic characteristics. Implementation of the controller, a modified hybrid digital pulse width modulator and a single look‐up table are developed. The digital controller was implemented on a field‐programmable gate array‐based control board. Experimental results demonstrating system validity are presented for a SIDO buck converter with nominal 3.6 V input voltage, and the outputs are regulated at 1.8 and 2.2 V. Copyright © 2012 John Wiley & Sons, Ltd.     

Fast‐transient DC‐DC converter using a high‐performance error amplifier with a rapid output‐voltage control technique

This letter presents a method for improving the transient response of DC‐DC converters. The proposed technique replaces the conventional error amplifier with a combination of two different amplifiers to achieve a high loop gain and high slew rate. In addition, a rapid output‐voltage control circuit is employed to further reduce the recovery time. The proposed technique was applied to a four‐phase buck converter, and the chip was implemented using a 0.18‐μm CMOS process. The switching frequency of each phase was set at 2 MHz. Using a supply voltage of 2.7–5.5 V and an output voltage of 0.6–1.5 V, the regulator provided up to 2‐A load current with maximum measured recovery time of only 6.2 and 6.5 μs for increasing and decreasing load current, respectively. Copyright © 2017 John Wiley & Sons, Ltd.     

Quasi‐active power factor correction on flyback‐based dc/dc converter

This paper presents a novel input current shaper based on a quasi‐active power factor correction (PFC) scheme. In this method, high power factor and low harmonic content are achieved by providing an auxiliary PFC circuit with a driving voltage which is derived from a third winding of the transformer of a cascaded dc/dc flyback converter. It eliminates the use of active switch and control circuit for PFC. The auxiliary winding provides a controlled voltage‐boost function for bulk capacitor without inducing a dead angle in the line current. Since the dc/dc converter operates at high switching frequency, the driving voltage is also of high switching frequency, which results in reducing the size of the magnetic components. Operating principles, analysis and experimental results of the proposed method are presented. Copyright © 2011 John Wiley & Sons, Ltd.     

Influence of period‐doubling bifurcations in the appearance of border collisions for a ZAD‐strategy‐controlled buck converter

The first period‐doubling bifurcation of a dc–dc buck converter controlled by a zero‐average dynamic strategy is studied in detail. Owing to the saturation of the duty cycle, this bifurcation is followed by a border‐collision bifurcation, which is the main mechanism to introduce instability and chaos in the circuit. The multiparameter analysis presented here leads to a complete knowledge of the relatioship between these two bifurcations. The results are obtained by using a frequency‐domain approach for the study of period‐two oscillations in maps. Copyright © 2010 John Wiley & Sons, Ltd.     

Motor performance investigation of an indirect matrix converter with a reactor‐free boost converter

This paper describes a three‐phase power converter which utilizes the neutral point of an induction motor and demonstrates the performance of the motor using the proposed method under various operating conditions. Several motor test results, such as the speed–torque characteristic, the torque impact, and the acceleration–deceleration characteristic, are included to confirm the performance of the induction motor. The structure of the proposed circuit consists primarily of an AC/AC converter [indirect matrix converter (IMC)] and a boost converter connected to the neutral point of the induction motor. In addition, this paper also proposes a method to reduce the ripple found in the battery current. Several experimental results show that the motor works well, and even the leakage inductance is utilized in the boost converter. © 2012 Institute of Electrical Engineers of Japan. Published by John Wiley & Sons, Inc.