首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 109 毫秒
1.
电流互感器的误差及其限值电流互感器(CT)在传递信息的过程中,必须消耗一小部分电流用于激磁,以使铁心磁化,进而在二次线圈中产生感应电势和二次电流。此激磁电流与CT 一次线圈匝数的乘积称为激磁安匝。CT 的误差就是由铁心所消耗的激磁安匝引起的。  相似文献   

2.
提出基于交直流正交磁化的半铁心可调电抗器的设计思想,以解决传统可调电抗器中存在的谐波较大、控制电流较高等问题.通过交流磁场和直流激磁的共同作用,可改变电抗器的有效电感量.实验结果显示,直流激磁增加时,电抗器的有效电感量会下降.与交流场正交的直流激磁可保持电抗器的线性特性,并使电抗器的电感量在一定工作电流范围内趋向稳定.运用铁磁学理论分析了正交磁化的内部机理,比较了2种绕制方式的可调电抗器的谐波特性.正交磁化的可调电抗器具有产生的谐波小、需要的激磁电流低等良好特性.  相似文献   

3.
针对直流剩余电流保护方法中传统的相位差法存在检测特征提取困难和硬件电路结构复杂的问题,提出了一种基于激磁电流一个周期内负半波持续时间特征的直流剩余电流检测新型相位差法。该方法通过检测激磁电流负半波的持续时间在剩余电流出现前后的差值来检测直流剩余电流。首先对激磁电流进行半波整流处理,将其负半波的持续时间转化为其幅值为零的时间。然后通过检测其幅值为零的持续时间在剩余电流出现前后的差值达到测量目的。基于该方法完成了直流剩余电流互感器硬件电路的设计,并通过实验验证了此方法的有效性。  相似文献   

4.
本文分析直流互感器的基本结构和测量功能,介绍基于电流比较仪来实现对直流互感器误差的测试方法。电流比较仪采用磁芯零磁通原理对激磁电流进行反馈补偿,其测量准确度理论上可以达到1×10-5。  相似文献   

5.
电流互感器误差有源补偿的新方法   总被引:4,自引:0,他引:4  
利用相似电流互感器提取激磁电流的方法过于复杂,且对被补偿对象具有选择性,文中提出一种新式简便的 提取激磁电流的方法,使补偿装置的结构大大简化,并且通过反匝数补偿措施,扩大了补偿对象的范围。激 磁电流补偿和反匝数补偿两种方法联合使用,不论被补偿的电流互感器有无匝数补偿,都能把精度由0.5级 提高到0.1级,且比差调试与角差调试相互解耦,调整很方便。  相似文献   

6.
一种电流互感器饱和误差补偿算法研究   总被引:1,自引:0,他引:1       下载免费PDF全文
在故障情况下,电流互感器(CT)的一次电流非常大,且含有衰减的直流分量,容易使CT饱和,导致二次电流严重失真,使继电保护装置或控制设备不能正常动作。本文提出了一种饱和二次电流的误差补偿算法。该算法根据测得的二次电流估计铁芯中的磁通量及激磁电流,并将估计的激磁电流加入到实测二次电流中,起到补偿作用,矫正失真的二次电流。EMPT仿真及算例分析证明了本文算法的有效性。  相似文献   

7.
μs级脉冲激励下磁开关磁芯磁特性   总被引:6,自引:4,他引:2  
为测试磁开关磁芯在μs级脉冲激励下的磁特性,设计并制作了基于没有附加磁芯复位电路的单级磁脉冲压缩系统,3块被测磁芯分别代表铁基非晶、Ni-Zn和Mn-Zn 3种软磁材料。磁芯的磁滞回线由测量所得的磁开关两端电压和电流数据经计算得到,由磁滞回线可知这3种软磁材料在μs脉冲激励下的各种特性参数。通过分析比较这些特性参数可知:铁基非晶磁芯具有最大的磁通跳变,同样的V-s积和匝数时,铁基非晶磁芯所需体积最小;Mn-Zn铁氧体磁芯具有最小的能量损耗,适合高重复频率下的应用;Ni-Zn铁氧体磁芯饱和后的相对磁导率最低,适用于较高压缩增益的磁压缩电路中。  相似文献   

8.
针对电机转子的鼠笼结构会导致总漏感随电流频率的不同而发生变化给激磁电感和转子电阻的测量带来偏差的问题,提出了一种离线辨识电机参数的算法。采用直流实验结合最小二乘法辨识定子电阻,采用低频交流实验辨识激磁电感和转子电阻,且激磁电感和转子电阻的辨识无需电机总漏感参数,从而消除了转子漏感参数变化给辨识带来的影响。另外,辨识算法辨识逆变器的非线性压降模型并对逆变器压降进行补偿以提高算法精度,激磁电感的辨识在不同激磁水平下进行以得到电机的激磁曲线。在TMS320F28035实验平台上实现辨识算法,验证了算法的辨识精度。  相似文献   

9.
该文采用磁滞模型与有限元分析结合的方法分析变磁通记忆电机磁化性能。通过研究铝镍钴永磁材料磁化特性,建立一种新型的磁滞模型,可计算出施加任意直轴电流脉冲下铝镍钴永磁体的磁化曲线方程,并给出变磁通记忆电机充退磁有限元分析方法。基于磁滞模型和有限元仿真结合的方法,研究了充磁过程中电机的磁场分布,以及电枢电流和转子位置对铝镍钴永磁体磁通密度的影响,以减小电机的最大充磁电流及充磁时间,进而降低电机充磁损耗并获得最佳充磁性能。并在考虑铝镍钴永磁体磁化程度不均匀的情况下,计算了不同充磁电流作用后电机的空载反电动势、气隙磁通密度以及充退磁特性曲线,评估了变磁通记忆电机的磁化性能。最后设计并制作了一台样机进行了实验验证,实验结果与有限元分析结果较为吻合。  相似文献   

10.
一种电流互感器饱和误差补偿算法研究   总被引:1,自引:0,他引:1       下载免费PDF全文
在故障情况下,电流互感器(cT)的一次电流非常大,且含有衰减的直流分量,容易使cT饱和,导致二次电流严重失真,使继电保护装置或控制设备不能正常动作.本文提出了一种饱和二次电流的误差补偿算法.该算法根据测得的二次电流估计铁芯中的磁通量及激磁电流,并将估计的激磁电流加入到实测二次电流中,起到补偿作用,矫正失真的二次电流.EMPT仿真及算例分析证明了本文算法的有效性. .  相似文献   

11.
在对变压器励磁涌流的仿真中,变压器铁芯的非线性磁化特性必须加以考虑。本文运用人工神经网络模拟主磁滞回环,以及用线性变化的位移来生成局部磁滞回线的方法,建立铁芯动态非线性磁化过程的计算模型。在此基础上对变压器的励磁涌流进行了仿真,收到了较好的效果。  相似文献   

12.
利用磁滞回线辨识变压器励磁电感研究   总被引:1,自引:0,他引:1       下载免费PDF全文
针对变压器在空载情况下副边电压,电流数据未知,励磁电感不易获取的缺陷,提出了利用变压器磁滞回线上的离散数据点求励磁电感的方法。该方法具体步骤是首先根据变压器空载时原边的电压电流采样数据点找出此时关于磁链与电流的函数关系(磁滞回线),然后由磁滞回线上关于磁链和电流的离散数据点找出算法求励磁电感。通过ATP和Matlab软件相结合,仿真出了磁滞回线和相对应的励磁电感,得出了磁滞回线和励磁电感变化情况与理论分析相符。此方法可以求出空载时的励磁电感。  相似文献   

13.
This paper presents a simulation algorithm to simulate the hysteresis characteristics in the core of a power transformer. The algorithm is based on the Jiles–Atherton phenomenological model of a ferromagnetic material. The new transformer model is capable of producing a close representation of the transformer magnetizing current. Comparisons are made between recorded and simulated waveforms using a single phase distribution transformer. A good agreement is achieved between recorded and simulated data.  相似文献   

14.
计及铁心动态磁化特性的三相变压器励磁涌流的仿真研究   总被引:8,自引:5,他引:8  
符杨  陈珩 《变压器》1997,34(9):4-11
介绍了计及铁心饱和,磁滞,局部磁滞和原始剩磁影响的三相三柱式变压器磁励涌流的仿真数学模型及仿真计算程序,对三相三柱式变压器空载合闸时的励磁涌流作了仿真计算,并对其结果进行分析。  相似文献   

15.
考虑铁磁磁滞的变压器励磁涌流仿真分析   总被引:4,自引:2,他引:2  
提出了一种考虑铁芯铁磁磁滞的变压器电磁暂态模型,并对变压器空载合闸时的励磁涌流现象进行了仿真研究。基于目前工程中应用较为广泛的Jiles-Atherton铁磁磁滞原理建立铁芯磁滞磁化曲线模块,通过设置适合的参数计算得到了与实际测量值较为吻合的 B-H曲线;通过分析单相三绕组变压器铁芯绕组结构及其电路模型,得到其电磁暂态计算模型;通过分析三相五柱式变压器磁路结构并利用对偶性原理,得到了其暂态计算分析模型。利用所建立的暂态计算模型对单相三绕组变压器的励磁涌流现象进行了仿真研究,仿真计算结果与实际试验测量结果的对比证明所提出的暂态计算模型的正确性和有效性;同时也对三相变压器组和三相五柱式变压器空载合闸时的励磁涌流进行了仿真计算,仿真结果证明所提出的暂态计算模型能够准确地分析变压器空载合闸时的励磁涌流现象。  相似文献   

16.
This article validates the possibility of a piecewise linear approximation with one breakpoint of the magnetizing characteristic of a power transformer for studying the processes of unilateral saturation of a magnetic system during periods of a high geomagnetic activity, which is caused by space-weather disturbances. An integral quantitative characteristic of a piecewise linear approximation is proposed that takes the features of the main magnetization curve of electric steel and the structural features of the power-transformer magnetic system into account. An analytical model is developed that allows determination of the instantaneous values and the harmonic structure of the magnetizing current at different intensities of quasi-direct currents. Two specific levels of the geomagnetic activity are determined. At one of them, the even harmonics of the magnetizing current are maximized, while at the second level the fundamental harmonic of the magnetizing current reaches a maximum that exceeds the certified value of the open-circuit current of the power transformer by several times.  相似文献   

17.
The DC component of current circulating in power transformers produces a certain degree of core saturation. The waveshape of the excitation current displays a pulse of high magnitude at each cycle. The width of the pulse depends on the period of the cycle under saturation. This excitation current induces a drop of potential across the primary winding impedance thus reducing the magnetizing voltage and injecting harmonics into the network. Moreover, it is demonstrated that this condition of operation will increase copper and stray losses but will tend to decrease iron losses.In order to study the detrimental effect of direct current, the equivalent circuit of a power transformer has been reviewed to confirm its applicability under partial saturation of the core. For single-phase transformers, the mathematical model developed allows calculation of rms and crest values of magnetizing current, core flux and magnetizing voltage, along with copper and core losses.  相似文献   

18.
500 kV电力变压器直流偏磁耐受性能的仿真研究   总被引:1,自引:0,他引:1       下载免费PDF全文
为了深入研究500 kV电力变压器的直流偏磁耐受性能,根据J-A磁滞回线理论,基于电路磁路模型建立了500 kV自耦变压器的直流偏磁仿真模型,通过改变J-A模型中的关键参数,仿真研究了矫顽力、剩磁和磁滞损耗等硅钢片磁化特性对500 kV变压器直流偏磁耐受性能的影响。仿真结果表明,变压器直流偏磁时,励磁电流出现畸变,有偶次谐波出现,励磁电流随直流分量的增大呈现不同的增幅。当磁滞回线的矫顽力增大时,励磁电流及其总谐波畸变率随外加直流分量的增幅变小。当剩磁和磁滞损耗增大时,励磁电流及其总谐波畸变率随外加直流分量的增幅加剧。研究结果可为大型变压器直流偏磁耐受能力评估及直流偏磁抑制措施提供理论依据和新思路,具有一定的实用价值。  相似文献   

19.
This paper deals with error compensation in current transformers. Usually the manufacturer tries to limit these errors by stating a transformer nominal ratio slightly different from the turns ratio. On the other hand techniques have been developed that allow software current compensation. The proposed method requires acquisition of the instantaneous secondary current and its adjustment with magnetizing current, taking into account hysteresis effects. To do this, a preliminary procedure is performed for core and transformer parameter identification. The compensation method has been tested on a variety of instrument transformers, with sinusoidal primary current. Test results show in all examined cases, an improvement in primary current reproduction accuracy, compared with that achieved using CTs nominal ratio, even for core partial saturation. A further development of the compensation technique is in progress, with a view to eliminating some restrictive hypothesis introduced in the present study  相似文献   

20.
Tests were conducted on several transformers rated at 100 kVA or less and on a power transformer rated 370 MVA in an effort to characterize the no-load losses and magnetizing resistance for transformers subjected to overexcitation and inrush current. Analysis of the results revealed that the magnetizing resistance changes as a function of the peak magnetization flux or the amplitude of the magnetic field. A new model of the instantaneous magnetizing resistance (IMR) as a function of the instantaneous flux has been developed and its dynamic use in the Electromagnetic Transients Program (EMTP) allows the form of the hysteresis cycle and the mean losses in overexcitation to be reproduced with a high degree of accuracy. The same model also accounts for losses due to the harmonics superimposed on the fundamental. The results showed that the IMR calculated under inrush current conditions is higher than that in overexcitation conditions.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号