共查询到20条相似文献,搜索用时 86 毫秒
1.
2.
不同结构土壤中接地网冲击特性的测量与分析 总被引:6,自引:3,他引:3
变电站接地网的冲击特性研究对于接地网的优化设计具有重要意义,为能系统真实反映接地装置在不同土壤结构中的冲击特性,基于量纲相似性原理,利用冲击电流发生器进行了接地网在均匀及双层土壤中的冲击接地模拟试验。在均匀土壤中测量了5种埋深、3种冲击电流注入点位置时对应的接地网冲击接地电阻值,并测量了典型情况下接地网的地表电位分布情况;在双层土壤中测量了3种土壤厚度、3种冲击电流注入点位置时对应的接地网冲击接地电阻值。通过分析不同试验条件下接地网模型的冲击接地电阻及电位分布得到了冲击电流注入点位置、地网埋深及土壤结构等因素对接地网的冲击接地特性的影响规律。 相似文献
3.
4.
接地网腐蚀状态电化学检测系统的开发与应用 总被引:5,自引:1,他引:4
开发研制接地网腐蚀原位电化学检测系统,采用小孔限流电化学传感器,实现了接地网金属电化学测试电流的限流;采用小波滤波软件和电化学检测参数解析软件,排除了发电厂、变电站、输电线路以及土壤等测试环境对电化学测试响应信号的干扰,准确解析出所测量接地网金属的极化电阻、土壤电阻等电化学参数。采用该系统进行接地网腐蚀检测时,无需开挖或停运地网,只需将传感器插入土壤中
(15 cm左右),测试引线连接在接地引下线上,便可获得地网金属腐蚀速度和腐蚀状态信息。 相似文献
5.
6.
《高压电器》2016,(9):98-102
为有效分析变电站接地网的冲击特性,提高变电站电气设备的运行可靠性和确保人身安全,文中以35 kV变电站用典型接地网为依托,基于量纲相似原理设计和定制了规则形状和不规则形状的两种接地网模型,通过模拟接地网导体变细、断裂和脱焊等典型故障,对接地网模型的冲击特性进行了试验研究。试验结果表明:接地网的冲击特性随冲击电流波形、注入点不同有较大差异,且规则接地网的暂态散流特性优于不规则接地网;对同一冲击电流注入点,冲击电流波形的波头时间越短,接地网的冲击接地电阻越大;冲击电流从接地网中心注入时,对应的冲击接地电阻最小;此外,接地网存在典型故障时,冲击接地电阻较之正常工况均有所增大,但增幅与冲击电流波形的波头时间有关。 相似文献
7.
为了了解土壤特性对接地网特性参数(接地阻抗、地线分流、地网电位升高、场区压差、跨步电压和接触电压)的影响规律,结合具体的工程案例,采用数值仿真方法,分析接地网特性参数与土壤分层结构特性之间的相关性。结果表明,站址土壤电阻率不同时,接地网特性参数在变电站发生单相接地短路故障时具有不同的表现行为,接地网特性参数是分层结构土壤电阻率、接地网结构和形状以及入地故障电流水平等几个因素协同作用的结果。高土壤电阻率条件不利于散流,地网电位升高较高,但整体压差较小,跨步电压和接触电压分布较为均衡。低分层土壤电阻率条件下,地网电位升高很低,但场区压差较大,高水平跨步电压和接触电压可能出现在接地故障点且超过安全限值,在设计时应注意均压措施的完善。 相似文献
8.
9.
介绍了上海市中心区域500kV静安全地下变电站的地网埋设情况,根据地网简化计算模型得出了地网的简化计算值.最后,对此复合地网进行瞬态特性的分析,应用CDEGS软件计算了在大短路接地电流情况下主接地网和等电位接地网的瞬态电位分布,得出瞬态电位分布对保护和自动化等设备的影响. 相似文献
10.
11.
12.
通过对几种不同成分的铅梯合金进行恒电流阳极腐蚀失重实验,金相观察等,分析了合金被细化晶粒后在其耐腐蚀性能方面的作用机理,指出了用阳极腐蚀失重法来说明板栅合金耐腐蚀性的同时,还应注重被腐蚀后其机械性能的减弱程度,以此阐明腐蚀速率和耐腐蚀性能应该是量和质的概念。同时指出我们还应注意到板栅合金在蓄电池使用过程中发生的应力腐蚀断裂。 相似文献
13.
采用粉末冶金法制备系列烧结钕铁硼磁体。采用扫描电子显微镜和电子能谱分析了磁体的微观组织成分,研究了其合金成分(包括Dy含量、Pr含量、稀土总量和微量添加元素)和工艺方法对磁体腐蚀失重影响,并分析了相关机制。实验结果表明,Pr含量、Dy含量以及稀土总量的控制可以改善磁体的失重,改善耐蚀性能。在此基础上通过优化磁体成分和制备工艺,制备出低失重磁体。改善后的磁体失重性能都达到了30天小于3 mg/cm2的水平。通过元素复合添加,提高了磁体磁性能及耐腐蚀性,使其能广泛应用于腐蚀环境。 相似文献
14.
采用浸泡法研究了镍铁基高温合金HT700T在800 ℃下添加不同剂量Al粉缓蚀剂的NaCl/KCl/MgCl2氯化物熔盐中的腐蚀行为,浸泡时间分别为200、300、400 h。采用X射线衍射(XRD)和配备能谱仪的扫描电子显微镜(SEM/EDS)对腐蚀产物的组成、形貌和元素分布进行了研究,分析了缓蚀剂对HT700T合金腐蚀行为的影响。结果表明:HT700T合金在800 ℃下腐蚀后,添加Al粉缓蚀剂可在样品表面生成具有面心立方结构的Ni3Al相;当Al粉缓蚀剂添加量为2%(质量分数)时,可在合金表面形成致密的Al2O3膜;当Al粉缓蚀剂添加量为10%(质量分数)时,Al向内扩散导致合金内部元素发生变化,形成由Al2O3、Al-Ni-Fe、Ni-Fe、Ni-Al、Ni-Al-Fe+Cr2O3组成的防护层,其深度随时间变化分别为185.8 μm(200 h)、145.66 μm(300 h)、166.02 μm(400 h),可有效降低800 ℃下氯化物熔盐的腐蚀速率。 相似文献
15.
The paper discusses materials and results of the most representative world forum on the problems of flow-accelerated metal corrosion in power engineering—Flow-Accelerated Corrosion (FAC) 2016, the international conference, which was held in Lille (France) from May 23 through May 27, 2016, sponsored by EdF-DTG with the support of the International Atomic Energy Agency (IAEA) and the World Association of Nuclear Operators (WANO). The information on major themes of reports and materials of the exhibition arranged within the framework of the congress is presented. The statistics on operation time and intensity of FAC wall thinning of NPP pipelines and equipment in the world is set out. The paper describes typical examples of flow-accelerated corrosion damage of condensate-feed and wet-steam pipeline components of nuclear and thermal power plants that caused forced shutdowns or accidents. The importance of research projects on the problem of flow-accelerated metal corrosion of nuclear power units coordinated by the IAEA with the participation of leading experts in this field from around the world is considered. The reports presented at the conference considered issues of implementation of an FAC mechanism in single- and two-phase flows, the impact of hydrodynamic and water-chemical factors, the chemical composition of the metal, and other parameters on the intensity and location of FAC wall thinning localized areas in pipeline components and power equipment. Features and patterns of local and general FAC leading to local metal thinning and contamination of the working environment with ferriferous compounds are considered. Main trends of modern practices preventing FAC wear of NPP pipelines and equipment are defined. An increasing role of computer codes for the assessment and prediction of FAC rate, as well as software systems of support of the NPP personnel for the inspection planning and prevention of FAC wall thinning of equipment operating in singleand two-phase flows, is accepted. Different lines of attack on the problem of FAC of pipelines and equipment components of existing and future nuclear power units are reviewed. Promising methods of nondestructive inspection of pipelines and equipment are presented. 相似文献
17.
Treatment of cooling water with INKORAM-75 copper corrosion inhibitor is applied for reducing corrosion processes in the copper-containing alloy of which turbine condensers are made. The results obtained from industrial trial of the INKORAM-75 inhibitor in the service cooling water system of the Novovoronezh NPP Units 3 and 4 are presented. 相似文献
18.
19.
20.