A novel triple notch‐bands ultra wide‐band band‐pass filters using parallel multi‐mode resonators and CSRRs

This article discusses a technique based on combination of multimode resonators (MMR) and complementary split ring resonators (CSRR) to design multi notch‐bands ultra wide‐band (UWB) band‐pass filters (BPF). The proposed structure consists of two parallel multimode resonators, resulting in a dual notch‐band UWB BPF, integrated with a single cell of CSRR to realize the third notch‐band. The mechanism of realizing the notch‐bands is mathematically presented and a triple notch‐bands UWB BPF is designed, simulated and fabricated. The overall size of the proposed filter is reported to be around 36 × 7.7 mm² where a size reduction of around 35% is demonstrated in comparison to the conventional filter. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:375–381, 2014.     

Compact UWB bandpass filter with dual‐notch bands using asymmetric tri‐section stepped impedance resonator

In this study, a novel high selective UWB band pass filter (BPF) with dual notch band is presented. UWB BPF is realized using stub‐loaded multiple‐mode resonator (MMR). The MMR is constructed by loading a quintuple mode open stub at the centre in an asymmetric tri‐section stepped impedance resonator (ATSSIR). Five modes, including two odd modes and three even modes, placed within UWB band. Two transmission zeros generated by the fractal stub improve the passband selectivity greatly. Two half wavelength long fractal Hilbert resonators are embedded near I/O line to achieve notch bands at 5.1 and 5.9 GHz. Aperture‐backed interdigital coupled‐lines are implemented to improve the coupling. The proposed prototype is fabricated and tested. The measured insertion loss is observed to be within 1.5 dB over the passband. By virtue of two transmission zeros (TZs), on either side of the passband, at 5.1 and 5.9 GHz, respectively, the passband selectivity is achieved with measured roll‐off factor at around 34 dB/octave. The out‐of‐band rejection of the filter is greater than 22 dB up to 18 GHz. The simulated results are in good agreement with the measured responses.     

A multi‐stub loaded compact UWB BPF with a broad notch band and extended stopband characteristics

A compact ultrawideband (UWB) bandpass filter (BPF) employing the principle of multiple mode resonance characteristics to create UWB passband with high selectivity and simultaneously having extensive stopband characteristic is presented. Utilizing five stubs attached along with the asymmetric trisection stepped impedance resonator (ATSSIR), the proposed resonator enables seven transmission poles inside the passband. As an additional attributes the projected filter triggers one transmission zero at 5.0 GHz which helps to mitigate WLAN signal interference. No additional circuitry is used to generate a notch band. The proposed prototype of UWB BPF is fabricated and estimated. Simulated and estimated results are in great understanding. The prospective filter displays a deliberate passband from 2.9 to 11.02 GHz. The filter unveils deceptive free wide upper stop band attributes till 25 GHz with least attenuation of 10 dB all through the stop band.     

Dual‐band band pass filter using stub‐loaded open‐loop resonators with wide controllable bandwidths

Two dual‐band band pass filters (BPF) using stub‐loaded open‐loop (SLOL) resonator are presented in this article. A novel coupling tuning method by changing the relative coupling position of the resonators is proposed to control the bandwidth of each passband in a wide range. Transmission zeros are created to improve the selectivity by source‐load coupling. Because of the large ratio of two bandwidths, a novel dual‐band matching method is proposed to match the different load impedances at two passband frequencies to the same source impedance. Hence, relax the fabrication requirement of gap. The proposed dual‐band band pass filter is designed and fabricated. The measured 3 dB fractional bandwidths (FBWs) of two 2.45/5.25 GHz dual‐band BPFs are 6.5%/14.5% and 9.8%/5.5%, respectively. The results are in good agreement with the simulation. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:367–374, 2014.     

Compact tri‐notched ultrawideband bandpass filter design using CSRR,DGS, and FMRR configurations

The folded multiple‐mode resonators with complementary split ring resonator (CSRR), and defected ground structures (DGS) are introduced for notched ultrawideband (UWB) bandpass filter (BPF) design in this article. Using the CSRR, FMRR, notched wide‐band BPF, a notch response can exist in the UWB passband for blocking the interference. Adjusting the size factor of CSRR, the wide tuning ranges of notch frequencies included the desired frequencies of 5.2/5.8 GHz are achieved. The lower insertion loss (0.31 dB), higher rejection level (?48.40 dB), wider bandwidth (FBW 75%), and wider stopband (extended to 2.01 f₀ below ?20 dB rejection level) of UWB band at the central frequency f₀ = 4.58 GHz are obtained. Second, design a CSRR, DGS, FMRR, tri‐notched UWB filter, the wider bandwidth (3.1–9.8 GHz) with FBW = 126%, lower insertion loss (0.26 dB), and higher rejection level (?44 dB) of UWB band at central frequency f₀ = 5.6 GHz are presented. Using the CSRR and interdigital couple, three notch responses can exist in the UWB passband for blocking the interference signals. Adjusting the size factor of CSRR and interdigital couple, the wide tuning ranges of notch frequencies included the desired frequencies of 5.18/6.10/8.08 GHz are achieved. The wide tuning ranges of three notched frequencies cover from 5.0 to 8.4 GHz. It is a simple way to control the notch responses. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:571–579, 2014.     

A tunable balanced dual‐band BPF with quasi‐independently controlled center frequency and bandwidth

In this paper, a balanced dual‐band bandpass filter (BPF) with high selectivity and low insertion loss performance is presented by employing stub loaded resonators (SLRs) and stepped impedance resonators (SIRs) into balanced microstrip‐slotline (MS) transition structures. The balanced MS transition structures can achieve a wideband common‐mode (CM) suppression which is independent of the differential‐mode (DM) response, significantly simplifying the design procedure. Six varactors are loaded into the resonators to achieve the electrical reconfiguration. The proposed balanced dual‐band BPF can realize quasi‐independently tunable center frequencies and bandwidths. A tuning center frequency from 2.48 to 2.85 GHz and a fractional bandwidth (20.16%‐7.02%) with more than 15 dB return loss and less than 2.36 dB insertion loss are achieved in the first passband. The second passband can realize a tuning center frequency from 3.6 to 3.95 GHz with more than 12 dB return loss and less than 2.38 dB insertion loss. A good agreement between the simulated and measured results is observed.     

Wide passband/stopband bandpass filter based on transversal signal interference concepts and modified branch‐line structure

A high selectivity wide passband filter with a broader stopband based on transversal signal‐interaction concepts and modified branch line structure (MBLS) is developed in this article. Two transmission paths, that is, one half‐wavelength transmission line and one MBLS, are used to realize signal transmission from Port 1 to Port 2. Then, two transmission zeros are introduced at both lower and upper sides of the passband, which are used to improve the passband selectivity greatly. The filter bandwidth can be easily controlled by reasonable adjusting the coupling coefficient of the coupled lines. Furthermore, with four stubs connected at the input/output ports, the stopband attenuation level is improved greatly. Finally, one prototype filter having 69.1% of 3 dB fractional bandwidth is fabricated with advantages of sharp selectivity and high out‐of‐band rejection. The EM simulated and measured results are presented, and an excellent agreement can be obtained. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:330–336, 2015.     

A folded dual‐mode bandpass filter with circular waveguide

In this article, a folded circular waveguide dual‐mode filter without tuning screws is designed for the fifth‐generation (5G) mobile communication system. The folded filter is composed of two stacked circular cavities operated at 3.5 GHz. Each cavity has two resonant modes, which can generate and control two transmission zeroes at specific frequencies. Through a coupling iris, the two single‐cavity filters are connected together, and can control four poles, which helps to expand the 3dB fractional bandwidth to 11.4%. The measured insertion losses are around 0.5 dB in the passband (from 3.4–3.6 GHz). The experiment results show an excellent agreement with the simulation results. Such folded filters have the advantages of very low insertion loss, compact size, high frequency selectivity, and low cost.     

Dual‐band filter with high selectivity and wide stopband rejection

This article presents a highly selective dual‐passband filter based on stepped‐impedance‐resonator (SIR) and mixed electromagnetic coupling. First, the surface area of the filter is effectively reduced by the triangular topology. Second, four controllable transmission zeros are introduced by source‐load coupling feed and mixed electromagnetic, which increases the selectivity of the filter. Third, a perturbation structure is added to independently control the resonance points of each passband. Finally, the improved defect ground structure (DGS) is integrated to obtain wide stopband rejection. The measured S‐parameters are well agreement with the simulated results, which show that the center frequencies of the two passbands are 2.4 GHz and 5.2 GHz; and the passband insertion losses are 0.85 dB and 1.6 dB; and the relative bandwidths are 14.6% and 5.7%, respectively. Besides, the structure is with six transmission zeros, and 20 dB suppression for the third harmonic and the fourth harmonic are achieved. Compared with the traditional SIR double‐passband filter, this filter has many advantages, such as simple design, small size, small insertion loss, controllable frequency, high selectivity, and high spurious suppression.     

Widely separated dual‐band half‐mode SIW bandpass filter

A novel half‐mode substrate integrated waveguide (HMSIW) based dual‐band bandpass filter (DBBPF) is proposed. Back to back connected two defected ground structure (DGS) resonators on the top layer of HMSIW cavity constitute the passband with two transmission zeros (TZs) at a lower frequency. The higher modes TE₃₀₁ and TE₃₀₂ of HMSIW cavity give the passband response at higher frequency using the mode shifting technique with slot perturbation. The source‐load coupling has been used to create finite frequency TZs to improve the selectivity of the second passband. Therefore, the proposed filter gives two widely separated passbands, center frequencies (CFs) at 5.83 and 18.1 GHz with an attenuation of greater than 10 dB between the passbands. The synthesized filter is fabricated using a low‐cost single layer PCB process, and the measured S‐parameters are almost mimic the EM‐simulation results.     

Ladder‐lattice bulk acoustic wave filters: Concepts,design, and implementation

This article presents a study of ladder‐lattice bulk acoustic wave (BAW) filters. First, a review of BAW technology and filters topologies is addressed. Next, a mixed ladder‐lattice BAW filter for application on W‐CDMA reception front‐ends (2.11–2.17 GHz) is presented. An improved solidly mounted resonators (SMR) technology was used for the filter implementation. The filter synthesis methodology is briefly described. Layout guidelines are discussed enabling an optimized filter design. The filter on‐wafer measurement results are as follows: ?3.55 dB of insertion loss, ?8.7 dB of return loss, an isolation higher than ?47 dB at the transmission band (1.92–1.98 GHz) and an improved selectivity (?30 dB at 2.14 GHz ± 60 MHz). Therefore, we can observe that the mixed topology combines the advantages of ladder and lattice networks, having very steep responses and an improved isolation at undesired bands. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Analysis and optimization of the unpredictable transmission zero in X‐band filter design

This article focuses on the common problem of uncontrollable transmission zero (TZ) in X‐band filter design. Using uniform impedance rectangular resonator (UIRR) to design an X‐band filter always results in an unpredictable TZ on the low‐frequency side of the passband, which greatly deteriorates the frequency selectivity of the filter performance. Electromagnetic coupling polarity analysis of the UIRR shows that the magnetic crosscoupling between nonadjacent resonators which is opposite to the main coupling plays a major role in the unpredictable TZ. By optimizing the UIRR from the loop structure with a small opening to the folded one, weak couplings between resonators are obtained. A high‐temperature superconducting filter at X‐band using folded UIRR resonator was designed and fabricated with a center frequency of 10.01 GHz and a bandwidth of 58 MHz, and the uncontrollable TZ has been removed successfully from the low‐frequency side of passband. The measured insertion loss is less than 0.4 dB and the return loss is greater than 15 dB.     

A novel compact wideband filter using three‐mode dual‐ring resonator

A novel compact wideband filter using three‐mode dual‐ring resonator is presented in this article. The resonator is constructed by two quarter wavelength transmission lines and a cascaded half wavelength dual‐ring. Formulae based on even‐ and odd‐mode analysis are derived to analyze the locations of the transmission poles and zeros of the resonator. Due to the transmission zeros in the lower and upper stopbands, the proposed filter exhibits sharp attenuations near the passband as well as very wide stopband. The filter is successfully realized by full wave EM simulation and fabricated. The measured responses of the filter agree well with the design simulation, and show that the fabricated filter has an insertion loss of better than 1.5 dB in the passband and two rejections of greater than 20 dB in the stopbands from 0 to 10GHz.     

Multi‐mode resonators with quad‐/penta‐/sext‐mode resonant characteristics and their applications to bandpass filters

In this article, a new class of dual‐/tri‐band and ultra‐wideband (UWB) bandpass filters (BPFs) using novel multi‐mode resonators are proposed. The classical even‐/odd‐mode method is applied to analyze the resonant characteristics of the proposed resonators, which exhibit controllable resonant modes with different dimension parameters under the same configuration. According to the analysis, three resonators with quad‐/penta‐/sext‐mode resonant characteristics are obtained by choosing the specific dimension parameters. Then, the quad‐mode resonator is used to design a dual‐wideband BPF centred at 2.39/5.14 GHz with 3‐dB fractional bandwidths (FBWs) of 36.9%/18.9%, and the penta‐mode resonator is utilized to design an UWB BPF with 3‐dB FBW of 102.2%, whereas the sext‐mode resonator is applied to design a tri‐band BPF with centre frequencies of 2.09/3.52/5.46 GHz and 3‐dB FBWs of 11.3%/20%/12.1%. All these three filters are fabricated and measured, and the measured results are in good agreement with the simulated ones.     

Ultra‐wide stopband low‐pass filter using symmetrical cascaded modified hairpin resonators

An elliptical function low‐pass filter (LPF) with ultra wide stopband and sharp cutoff frequency is proposed. This filter is composed of symmetrical cascaded modified hairpin resonators and U‐shaped resonators. The transition band is from 1 to 1.21 GHz with ?3 and ?20 dB, respectively. For this filter, the return loss is better than 17 dB in 80% of passband width, where the insertion loss is less than 0.3 dB. The band‐stop rejection is greater than 20 dB from 1.21 to 26.35 GHz and 40 dB from 1.35 to 12.5 GHz. To validate the design and analysis, the proposed LPF has been designed and fabricated on a 20 mil thick RO4003 substrate with a relative dielectric constant 3.38 and loss tangent of 0.0021. The filter is evaluated by experiment and simulation with a good agreement. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:314–321, 2014.     

Microstrip dual‐band bandpass filters using parallel‐connected open‐loop ring resonators

This article proposes a microstrip dual‐band bandpass filter that uses parallel‐connected open‐loop ring resonators. Compared to many microstrip dual‐band filters, the advantages of using microstrip open‐loop ring resonators are easy calculation (half‐guided‐wavelength), easy fabrication (equal width for all 50‐Ω lines and without grounding holes), and direct connection to external feed lines (reducing insertion loss caused by gap couplings). Another advantage of the filter is an asymmetrical feed on the ring resonator that provides sharp rejections at its adjacent bands. The input and output matches of resonators to the external feed lines are derived using a simple transmission‐line theory. The results of the derivation provide a simple design rule for filter designers. Simulated and measured results are presented with good agreement. The filter has minimum insertion loss of 1.25 dB at 1.85 GHz and 1.6 dB at 2.33 GHz. The 3‐dB fractional bandwidths are 5.9% for the 1.9‐GHz bandpass filter and 4.7% for the 2.4‐GHz bandpass filter, respectively. © 2008 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2008.     

Design of high selectivity tri‐band bandpass filter with wide upper stopband

This article presents a dual‐plane structure high selectivity tri‐band bandpass filter (BPF) which consists of a pair of T‐shaped microstrip feed lines with capacitive source‐load coupling as well as spur lines embedded, and three resonators, i.e., a dual‐mode stub‐loaded stepped impedance resonator and two nested dual‐mode defected ground structure resonators. Using the intrinsic characteristics of the resonators and feed lines, nine transmission zeros near the passband edges and in the stopband can be generated to achieve high selectivity. An experimental tri‐band BPF located at 2.4/5.7 GHz [wireless local area networks (WLAN) application] and 3.5 GHz [worldwide interoperability for microwave access (WiMAX) application] has been simulated and fabricated. Good agreement between the simulated and measured results validates the design approach. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Compact notch filter design using stepped impedance resonators for sharp roll‐off and large wideband rejection

This article presents the design of a compact notch filter with a sharp roll‐off and high rejection over a wideband. The filter comprises stepped impedance resonators that are interconnected to each other at strategic points on the resonator for optimal 3 dB roll‐off and high rejection over a wide stop‐band. The fabricated third‐order filter exhibits a steep 3 dB roll‐off and rejection exceeding 50 dB over the frequency range 2.70–6.19 GHz. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:490–494, 2015.     

A compact dual‐band superconducting filter with fine‐tuning coupling structure

A novel dual‐mode optimized patch capacitor loaded T‐type resonator is proposed for the design of a dual‐band filter (DBF). The resonator has its lowest even‐ and odd‐mode at the two expected passband frequencies and the first spurious mode far away from the passbands. For tuning of the two sets of coupling strengths for both passbands, open/shorted secondary coupling structures are introduced as a fine‐tuning coupling structure to increase/decrease the primary coupling strength. A four‐pole DBF with passbands centered at 2450 and 3500 MHz, respectively, is proposed and fabricated using the HTS material. The measured results of the filter indicate superior performance and good fitting with the simulation results. The return losses of both passbands and the insertion losses obtained by measurements are greater than 14 dB and less than 0.3 dB, respectively. The stopband rejection exceeds 50 dB up to 8.0 GHz.     

Coupled‐line band‐pass filter with T‐shaped structure for high frequency selectivity and stopband rejection

A coupled‐line band‐pass filter (BPF) with T‐shaped stub structure is presented. Five transmission poles within the passband and eight deep transmission zeros (TZs) from 0 to 2f₀ (f₀ denotes filter's center frequency) are realized through input impedance calculations. With the simple T‐shaped structure, the positions of six TZs can be appropriately adjusted to achieve high frequency selectivity and stopband rejection. For demonstration, a BPF prototype centered at 2.05 GHz is designed and fabricated, whose measured rejection levels are of over 45.5 dB at lower stopband and better than 19.5 dB at upper stopband. The simulation and measurement results are in good agreement, which validates the design idea.