首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到19条相似文献,搜索用时 125 毫秒
1.
矩形脉冲涡流传感器的缺陷定量检测仿真研究   总被引:1,自引:0,他引:1  
传统的脉冲涡流传感器由于其结构特点,在实际检测中存在自身激励干扰,使得其对缺陷的检测灵敏度不高。为了提高传感器对缺陷的检测能力,采用矩形传感器对铝板上缺陷进行检测。在分析矩形脉冲涡流传感器检测原理的基础上,采用ANSYS仿真软件建立了矩形脉冲涡流传感器检测模型,对矩形激励下方铝板表面涡流分布进行了仿真计算,研究了缺陷对空间三维磁场的扰动规律。仿真结果表明:矩形传感器能够在铝板表面激励出均匀的感应涡流;当有缺陷存在时,提取三维响应信号的幅值为特征量,分析传感器在扫描路径上不同位置检测幅值的变化特征发现,通过3个信号幅值变化的位置和幅值变化的程度可以实现对缺陷长度,宽度和深度进行定量检测。  相似文献   

2.
异种金属焊接结构在使用过程中容易产生损伤,因此需对其进行检测;脉冲涡流一发一收式非同轴(Transmitter Receiver,Tx-Rx)探头可应用于异种金属焊缝缺陷检测;然而,考虑到异种金属焊接构件成分多样、结构复杂的特点,需对Tx-Rx探头的摆放位置进行了优化;首先,建立仿真模型,讨论了激励线圈的摆放位置对试件中涡流及涡流扰动的影响,结果表明,当激励线圈位于带堆焊的合金钢上方时,其表面涡流强度及涡流扰动强度较大;其次,建立实验平台,实验表明,当激励线圈放置在带堆焊的合金钢上方时,其检测信号幅值和差分信号幅值最大;最后利用差分信号的峰值对焊缝缺陷的定量展开分析;脉冲涡流Tx-Rx探头的研究可为其在异种金属焊缝缺陷的应用提供参考.  相似文献   

3.
针对脉冲漏磁检测技术对不同方向的漏磁分量进行分析时存在一定局限性的问题,基于脉冲漏磁(PMFL)检测中的U型磁轭和脉冲涡流(PEC)检测中的矩形空心激励线圈,提出了脉冲聚磁(PMC)检测方法.通过仿真和实验分析了铁磁性试件在脉冲漏磁和脉冲聚磁两种检测模式下,缺陷部位的响应信号X,Y和Z3个分量的检测效果.结果表明:脉冲聚磁检测方法在进行铁磁性材料构件的缺陷检测时,激励探头对被测试件的3个方向的分量激励效果更明显,同时对于不同深度的表面缺陷,脉冲漏磁响应信号的三维分量具有更高的检测灵敏度.  相似文献   

4.
多层金属结构腐蚀缺陷脉冲涡流检测技术研究   总被引:1,自引:0,他引:1  
徐平  罗飞路 《自动化仪表》2007,28(11):25-28
脉冲涡流检测技术是目前唯一能对飞机多层金属结构中出现的腐蚀缺陷进行定量检测的技术。在对脉冲涡流检测技术进行研究的基础上,设计并实现了一套完整的脉冲涡流检测系统。提取检测信号的峰值、峰值时间、过零时间等时域特征量,实现对腐蚀缺陷的定量检测和缺陷位置的分类识别,并通过进一步的实验加以验证。  相似文献   

5.
为解决在脉冲远场涡流检测中检测线圈体积较大、控件分辨力低且在低频域灵敏度差的问题,通过有限元仿真,对不同位置不同深度的缺陷进行了基于磁场测量的脉冲远场涡流检测非磁性平板仿真。结果表明:在对激励线圈施加屏蔽后可以实现远场涡流效应,当缺陷位于激励线圈与二维节点中间时,检测效果最好,并且缺陷深度与磁通密度差分幅值密切相关,且具有良好的线性关系,可以实现对缺陷的定位及定量分析。  相似文献   

6.
飞机轮毂裂纹检测涡流探头的设计与实现   总被引:1,自引:0,他引:1  
为了实现对飞机轮毂根部疲劳裂纹的无损检测,设计了一种放置式线圈探头,该探头由1个检测线圈和1个参考线圈组成,利用电桥电路实现对微弱裂纹信号的差动放大检出。信号调理电路采用正交锁相放大对输出进行正交分解,得到包含信号幅值和相位信息的两路直流分量作为裂纹检测的特征量。根据数值仿真得出的结论指导实际探头的设计,对轮毂试件的检测结果表明:该探头能够很好地实现轮毂根部具有一定曲度的表面上小裂纹的检测,且灵敏度高。  相似文献   

7.
脉冲涡流检测方法是涡流检测技术的一个新兴分支。分析了InSb磁敏电阻器作为脉冲涡流检测元件的工作原理。应用InSb磁敏电阻器的涡流探头检测金属裂纹特征的信息提取方法。对采集的信号首先通过同步累加法处理后再经多项式拟合、小波变换实现对信号的滤波与平滑,最终选用小波变换提取裂纹的特征。实验表明:采用InSb磁敏电阻器作为脉冲涡流检测敏感元件,具有较高的裂纹灵敏度,且可以较好地反映裂纹的深度。  相似文献   

8.
一种用于盘孔裂纹检测的差动式涡流探头的设计与实现   总被引:4,自引:1,他引:3  
为了实现对某型发动机篦齿盘均压孔的原位、无损探伤,设计了一种差动式的涡流检测探头,探头由一个激励线圈和两个感应线圈组成,由于检测线圈结构上的对称性使得探头对盘孔周边的表面裂纹敏感,同时对激励线圈和检测线圈匝数比的优化设计也能有效增强输出的差动信号,降低干扰。信号调理电路采用正交锁相放大对输出进行正交分解,得到包含信号幅值和相位信息的两路直流分量作为裂纹检测的特征量。对篦齿盘均压孔标准试件的检测结果表明该探头能够很好地实现盘孔周边微小裂纹的检测,灵敏度高。同时,这种差动式的探头结构同样也可用于其它盘孔的裂纹检测。  相似文献   

9.
远场涡流技术广泛应用于铁磁性管道缺陷检测,但探头放入管内时通常需要设备停机。为满足压力管道的在役检测需求,传感器被置放于管外。本文对管道弯头处内外壁缺陷深度和外管壁缺陷走向检测信号的幅值和相位进行研究。结果表明:弯头处传感器电压信号的相位随缺陷深度的增加而近似线性减小,可用于缺陷深度的定量。管壁处传感器电压信号的幅值随外管壁缺陷走向由周向往轴向逐渐增大,可用于同深度缺陷走向的判断。综合运用上述特征信息,可在实际检测中补偿由缺陷走向给深度定量带来的误差。  相似文献   

10.
针对单向碳纤维复合材料分层缺陷难以检测的问题,设计了一个共面三矩形线圈探头,建立了利用该探头进行单向碳纤维复合材料分层缺陷垂直涡流检测的有限元模型,并利用该模型仿真计算了存在不同厚度分层缺陷时垂直涡流检测探头输出的感应电压信号变化情况。仿真结果表明,所设计的探头可灵敏地检测出单向碳纤维复合材料分层缺陷,并且在探头扫描检测分层缺陷的过程中,探头输出的感应电压虚部会出现成对的峰值和次峰值,峰值与分层厚度成正比,次峰值对的出现位置对应于分层缺陷边缘的位置,通过对峰值大小和次峰值对的出现位置进行分析,可以实现单向碳纤维复合材料分层缺陷厚度和范围的定量化评估,为实际工程应用提供了有价值的参考。  相似文献   

11.
R.S.  A.  S.  G.Y.   《Sensors and actuators. A, Physical》2008,144(1):222-228
We present recent work on a dual probe system containing electromagnetic acoustic transducers (EMATs) generating and detecting surface ultrasonic waves, and a pulsed eddy current (PEC) probe. This system is able to detect and size surface and near-surface defects in electrically conducting samples by looking at changes in the detected signal for each probe. By combining the information from each probe using a weighted logic function for data fusion, it is possible to both classify and size defects, with increased reliability. By combining the data in this way one obtains information about the defects which is not available when using either probe in isolation. Typical results on steel and aluminium samples are presented, along with information about the data fusion function. The dual probe and data fusion routine has been demonstrated to work at manual-scanning speeds, with higher speeds possible following some simple improvements to the system.  相似文献   

12.
为精准定位建筑外表缺陷,研究了基于三维激光扫描技术的建筑墙体外表面缺陷无损检测方法。采集建筑墙体信息,配准三维点云建筑墙体数据。选取RANSAC改进算法完成建筑墙体平面特征的提取。将其输入极限学习机中,输出建筑墙体外表面缺陷无损检测结果。实验结果表明,该方法可以有效检测建筑墙体外表面缺陷,实现建筑墙体外表面缺陷的精准定位,提升建筑的全寿命周期。  相似文献   

13.
许小润  吴贵芳 《计算机应用》2010,30(8):2247-2249
针对传统的图像检测算法对具有噪声以及光照不足或不均匀的带钢表面图像检测时效果不理想的问题,提出了基于人工免疫系统的带钢表面缺陷检测技术。根据检测器和抗原之间的论域空间包含关系,以及自体在论域空间中的位置信息,引进了分块空间的方式,提出了检测器分块的生成算法,对缺陷图像表面灰度信息进行三维恢复,获得带钢表面缺陷的高度信息,实现其三维质量检测。实验表明,该方法无论是在对比度低、光照不均还是有噪声干扰的情况下相对于传统的图像检测算法具有较好的处理效果。  相似文献   

14.
针对手术导航探针可视化与实时跟踪技术进行了研究.文中对电磁定位方法进行了介绍,设计了电磁定位下具有数据采集功能的探针.首先,应用3维实体造型技术构建探针的模型,完成实体几何模型向3维表面模型的转化.其次,使用旋转.沣册方法对针尖进行注册,并进行了精度测试.然后,应用最近点迭代(ICP)算法实现CT模型与患者位置的术中注...  相似文献   

15.
为了实现涡流无损检测的定量评估,设计了一种直接测量涡流磁场的涡流检测探头,该探头包含两个激励线圈和一个检测线圈.通过有限元法建立三维涡流仿真模型,对比研究导体内有无圆柱形缺陷时涡流的分布情况以及检测线圈响应的变化量.仿真结果显示,当导体内存在圆柱形缺陷时,涡流密度会集中分布在缺陷的侧面区域并且其大小会增加;检测线圈中响应的变化量与缺陷体积之间的关系满足两个指数函数的线性组合,对于体积较小的缺陷,检测线圈中响应的变化量与缺陷的体积近似成正比关系.实验结果验证了导体内存在小体积的缺陷时,检测线圈中响应的变化量与缺陷的体积之间的近似正比关系,证明了该结构的探头可以用于对缺陷的定量研究.  相似文献   

16.
We present the design, fabrication and experimental characterization of a new micromachined electromagnetic probe, which can be readily adapted to various biological manipulation and stimulation applications. The micro electromagnetic probe consists of a protruding (out-of-chip), sharp Permalloy needle embedded into a three-dimensional gold conducting coil. The probe fabrication is carried out using traditional surface micromachining processes coupled with assembly techniques. This hybrid approach significantly reduces fabrication difficulties and provides a simple and straightforward technique to realize integrated core-coil geometries. Furthermore, by using a scanning Hall probe microscope (SHPM), a comprehensive, high-spatial resolution characterization of the probe performance (e.g. peak magnetic intensity and spatial field distribution) is achieved for the first time. The manipulation of sub-micron sized magnetic particles with the developed micro electromagnetic probe is also demonstrated.  相似文献   

17.
涡流检测方法广泛应用于导电材料的缺陷检测和无损评价中。受趋肤效应的影响,常规涡流检测法通常只能检测导体表面缺陷。有学者提出了一种相移场探头,并通过实验验证了该探头在满足一定激励条件时,可以达到抑制导体表面涡电流密度,而增加导体深处涡电流密度的效果,从而可以检测导体更深处缺陷。但该结论仅有实验结果,还没有理论方面的验证。本文采用解析方法研究了该相移探头与导体的相互作用,推导出导体中涡电流分布的精确理论表达式,然后分析相位、激励频率对涡电流分布的影响,并计算了导体不同深度涡电流密度分布。从理论上验证了该探头设计及激励方法具有改变导体涡电流密度分布,增加导体深处涡电流密度的效果。  相似文献   

18.
The geometry of cutting flutes and the surfaces of end mills is one of the crucial parameters affecting the quality of the machining in the case of end milling. These are usually represented by two-dimensional models. This paper describes in detail the methodology to model the geometry of a flat end mill in terms of three-dimensional parameters. The geometric definition of the end mill is developed in terms of surface patches; flutes as helicoidal surfaces, the shank as a surface of revolution and the blending surfaces as bicubic Bezier and biparametric sweep surfaces. The proposed model defines the end mill in terms of three-dimensional rotational angles rather than the conventional two dimensional angles. To validate the methodology, the flat end milling cutter is directly rendered in OpenGL environment in terms of three-dimensional parameters. Further, an interface is developed that directly pulls the proposed three-dimensional model defined with the help of parametric equations into a commercial CAD modeling environment. This facilitates a wide range of downstream technological applications. The modeled tool is used for finite element simulations to study the cutting flutes under static and transient dynamic load conditions. The results of stress distribution (von mises stress), translational displacement and deformation are presented for static and transient dynamic analysis for the end mill cutter flute and its body. The method described in this paper offers a simple and intuitive way of generating high-quality end mill models for use in machining process simulations. It can be easily extended to generate other tools without relying on analytical or numerical formulations.  相似文献   

19.
The joint application of direct numerical simulation (DNS) and a combined multiple-direct forcing and immersed boundary method (MDF/IBM) is proposed to investigate the transitional boundary-layer flow induced by three-dimensional roughness elements. The multi-direct forcing technique is used to calculate the interacting force between the solid surface of roughness elements and the fluid, and let the no-slip boundary conditions be satisfied. In order to validate the efficiency of these numerical methods, a flow past an isolated three-dimensional hemispherical roughness element mounted on a flat plate is simulated. The evolutional process of the discrete hairpin vortex and the formation of two kinds of secondary vortex structures are captured. The comparisons of profiles of streamwise mean velocity and velocity fluctuation between the simulated results and the experimental ones show great quantitative agreement. The evolution of disturbances and the growth of steady disturbance energy prove the transient growth mechanisms underlying the transitional flow induced by moderate-amplitude isolated three-dimensional roughness elements. Numerical methods used in this investigation can be extended to the simulation of the transitional boundary-layer flows induced by randomly distributed three-dimensional roughness elements.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号