Wideband linear microstrip array antenna with high efficiency and low side lobe level

In this letter, the design and fabrication of the linear microstrip array antenna by series fed are presented. The array antenna consists of 16 reflector slot‐strip‐foam‐inverted patch (RSSFIP) antennas. The gain and efficiency of the linear array antenna is 16.6 dBi and 61% at 10 GHz, respectively. The antenna has a bandwidth (BW) of 45% from 8.1 to 12.8 GHz (S₁₁ < ?10 dB) and side lobe level (SLL) of ?25.6 dB across the BW of 19.2% from 9.4 to 10.4 GHz. These are achieved by using a microstrip series fed with defected ground structure (DGS) to feed the patch array antenna. Good agreement is achieved between measurement and simulation results.     

Low‐cost and wideband circularly polarized slot antenna array

A slot antenna with wideband circular polarization (CP) array, which operates on millimeter waves band, is proposed. A four‐direction sequential rotation technique is used in the feed network to feed the 2 × 2 slot element based on waveguide. The shot element resonates at both the fundamental mode and the high‐order mode. The slot element is studied in high order mode, and the radiation lobe can be redirected by changing the size of the slot element, thus improving the multi‐lobe problem. A strong single lobe is formed in the +z‐direction by using the ground edge diffraction characteristics of the slot element in the waveguide. The designed broadband characteristics are obtained through the appropriate combination of the feed network and CP antenna. The prototype of the antenna with an overall size of 137 mm × 137 mm × 0.6 mm³ is processed and verified by experiments. The prototype of the slot array is processed and examined. The test results display that the device has good performance of |S₁₁| < ?10 dB bandwidth of 3.72 to 6.56 GHz (2.84 GHZ, 55.25%), a 3 dB axial ratio bandwidth of approximately 4.39 to 5.43 GHz (21.18%).     

A broadband coplanar waveguide to rectangular waveguide power divider using a slot

In this article, a broadband coplanar waveguide (CPW) to rectangular waveguide power divider using the dipole slot is proposed. The power divider consists of an input CPW port and two output rectangular waveguide ports. The CPW to rectangular waveguide power divider using the dipole slot has a return loss larger than 15 dB and an insertion loss equal to 3.08–3.27 dB in the whole X‐band (8.2–12.4 GHz). Furthermore, to broaden the bandwidth, the dipole slot is replaced by the bow‐tie slot. The CPW to rectangular waveguide power divider using the bow‐tie slot yields a return loss larger than 16 dB and an insertion loss equal to 3.05–3.29 dB from 8 to 13 GHz, which exceeds the X‐band. To verify our design, power dividers that use the dipole slot or the bow‐tie slot are fabricated and measured. The measurement results of both power dividers are in good agreement with the simulation results. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

Broadband high‐gain slot grid array antenna for millimeter wave applications

A broadband high‐gain slot grid array antenna (SGAA) is proposed in this paper. Based on the electromagnetic complementarity principle, the metal elements in the traditional microstrip grid array antenna (GAA) are replaced by a wide slot element. Compared with the GAA, the proposed SGAA achieves broadband and high‐gain performance. In order to demonstrate this concept, a prototype with 9‐element SGAA is designed using wide slot radiation elements and fabricated on Rogers 5880 printed circuit board (PCB) substrates, which is fed by a 50 Ω coaxial probe. The measured and simulated results show a good agreement. The proposed SGAA achieves a measured peak gain of 14.8 dBi at 26.0 GHz, a 10‐dB impedance bandwidth from 22.2 to 28.5 GHz with a fractional bandwidth of 24.9%. These results indicate that the SGAA is with high performance and it is suitable for the fifth‐generation (5G) millimeter wave (mmW) wireless communication system.     

Millimeter‐wave planar high gain SIW antenna using half elliptic radiation slots

This article reports a high gain millimeter‐wave substrate integrated waveguide (SIW) antenna using low cost printed circuit board technology. The half elliptic slots which can provide small shunt admittance, low cross polarization level and low mutual coupling are etched on the board surface of SIW as radiation slots for large array application. Design procedure for analyzing the characteristics of proposed radiation slot, the beam‐forming structure and the array antenna are presented. As examples, an 8 × 8 and a 32 × 32 SIW slot array antennas are designed and verified by experiments. Good agreements between simulation and measured results are achieved, which shows the 8 × 8 SIW slot array antenna has a gain of 20.8 dBi at 42.5 GHz, the maximum sidelobe level of 42.5 GHz E‐plane and H‐plane radiation patterns are 22.3 dB and 22.1 dB, respectively. The 32 × 32 SIW slot array antenna has a maximum measured gain of 30.05 dBi at 42.5 GHz. At 42.3 GHz, the measured antenna has a gain of 29.6 dBi and a maximum sidelobe level of 19.89 dB and 15.0 dB for the E‐plane and H‐plane radiation patterns. © 2015 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:709–718, 2015.     

Circularly polarized stacked patch antenna array with enhanced bandwidth for S‐band applications

In this article, a circularly polarized coupled slot 1 × 4 stacked patch antenna array with enhanced bandwidth is proposed for S‐band applications. Initially, a patch antenna radiating at 2.79 GHz is designed and maximum energy from feedline to patch element is coupled using two rectangular slots. Whereas, a parallel feedline structure is designed to provide polarization flexibility by creating 0, 90 , and 180^o phase differences. Then, a truncated patch element is vertically stacked in the design to achieve broader bandwidth of 600 MHz over frequency range from 2.4 to 3.0 GHz. Finally, a coupled slot 1 × 4 array stacked antenna array having feedline line structure to provide 90^o phase difference for circular polarization is designed and fabricated for measurements. It is observed that the final design achieved target specification having impedance matching (|S₁₁ | (dB) < ?10 dB over 2.4 to 3.0 GHz, broad band circular polarization, and 11.5 dBic total gain. Overall, a good agreement between simulated and measurement results is observed.     

Slot antenna array for fifth generation metal frame mobile phone applications

An eight‐element antenna array based on open/closed slot modes that can cover the 3.5 GHz band (3400‐3600 MHz) is proposed and studied. There are two kinds of antenna elements with the slot sizes of 10.8 × 1 mm² and 28.8 × 1 mm² for open and closed slot modes, respectively. Both the two kinds of antenna elements are realized with the help of the metal frames with the height of 7 mm at the two long sides of the ground. The proposed antenna array is suitable for 5G metal frame mobile phone applications. A prototype is fabricated and measured. The measured results show that all the eight antenna elements can cover the band of 3400‐3600 MHz and the isolations are bigger than 13 dB, the measured efficiencies all are bigger than 42% and the measured envelope correlation coefficients are lower than 0.15.     

A coplanar‐waveguide‐fed planar integrated cavity backed slotted antenna array using TE33 mode

This short communication presents a substrate integrated waveguide planar cavity slotted antenna array. The proposed antenna array, excited in its TE₃₃ higher mode, incorporates a grounded coplanar‐waveguide (CPW) CPW‐feeding excitation mechanism. The electromagnetic energy is coupled to the air through 3 × 3 slot array etched on top metallic layer. The proposed antenna operates in the X‐band for the frequency range around the 10 to 11 GHz with resonances at 10.4 and 10.8 GHz frequencies. The proposed antenna array was fabricated and tested. Experimental results show good impedance matching with enhanced radiation characteristics, in terms of peak gain, cross‐polarization level, and low back‐radiation. The proposed antenna has the advantages of low‐footprints, lightweight, high gain, low‐cost, and ease of integration with other electronic circuits. With these characteristics, the proposed antenna array can find its applications in compact wireless digital transceivers.     

A polarization‐reconfigurable array design based on mode combination technique

This article reports a novel polarization‐reconfigurable antenna array using the technique of mode combination (MC). It can electronically alter its polarization states between left‐hand circular polarization mode, right‐hand circular polarization mode, and linear polarization (LP) mode. The antenna array consists of 2 × 2 microstrip antenna elements with one L‐slot on each square patch and two PIN diodes located in the slot region. Instead of degenerating circular polarization (CP) and LP modes by exciting different radiation parts of the antenna element, the LP one is combined by orthogonal CP modes generated by adjacent elements of the proposed antenna array. To verify the concept, a prototype is manufactured and tested. Experimental results show that the proposed antenna has an overlapped ?10 dB impedance bandwidth of around 11.2% for both CP modes and the LP one. The realized maximum gains are around 7.5 dB for the CP modes and 5.6 dB for the LP mode, which are satisfactory for wireless local area network in wireless communication systems.     

A compact slot antenna configuration for ultrawideband (UWB) terminals and mobile phones

A novel technique to design a mobile phone antenna by using an ultrawideband (UWB) antenna configuration is proposed. The technique is validated with a novel printed slot antenna configuration. The slot is composed of a circle connected to a trapezoid and fed by means of a 50 Ω microstrip line connected to a patch with similar shape to the slot. An UWB antenna with size of 19 mm × 24 mm and measured ?10 dB bandwidth of 2.97‐11.32 GHz is developed based on the configuration. When the configuration is applied in a system circuit board of 60 mm × 115 mm to design a mobile phone antenna, the simulated ?6 dB bandwidths are 1.0‐1.2 GHz and 2.25‐15 GHz. To enhance antenna bandwidth, another slot with rectangular shape is etched in the ground plane, and the microstrip line is moved to the center of the circuit board and folded to distribute along the rectangular slot. The measured ?6 dB bandwidths of the mobile phone antenna are 0.69‐1.09, 1.68‐2.75, 3.45‐3.52, and 3.62‐15 GHz.     

A WiMAX circularly polarized antenna array using slot‐coupling feeding technique

In this letter, we present a circular polarization antenna array using the novel slot‐coupling feeding technique. This antenna includes eight elements which are installed in line, each array element is fed by means of two microstrip lines with equal amplitude and phase rotation of 90°. The feeding microstrip lines are coupled to a square patch through a square‐ring slot realized in the feeding network ground plane. With the presence of the slots, this antenna array is able to cover the range of frequency of 3 GHz to 4 GHz. The size of the proposed antenna array is 7λ × 1.8λ × 0.4λ. The measured gain is 15.2 dBi and the bandwidth of S11< ?10 dB is 1 GHz (3–4 GHz, 28%). The antenna array is suited for the WiMAX applications. With the use of slot‐coupling feeding technique, the measured bandwidth for axial ratio < 3 dB is about 24% in the WiMAX frequency band (3.3–3.8GHz). The measured HPBW of the y–z planes is larger than 62°. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:567–574, 2016.     

Ultra‐wideband slot antenna for wireless communication systems

In this article, a new ultra‐wideband rectangular‐slot antenna is proposed and developed for multiband wireless communication systems. The radiating slot is fed by a microstrip line with a microstrip fork‐shaped tuning stub. The frequency characteristic and radiation performance of the proposed antenna are successfully optimized, and a prototype is fabricated and tested. The measured results show that the impedance bandwidth can cover the band from 1.85 to 6.1 GHz with return loss of better than 10 dB, and the corresponding radiation displays omnidirectional patterns across the interested bands. With these frequencies, the proposed structure is especially suitable for applications in wireless communication systems, where a single antenna is needed to operate simultaneously at different bands, such as PCS (1.85–1.99 GHz), UMTS (1.92–2.17 GHz) and all WLAN bands (2.4–2.48 GHz and IEEE802.11a WLAN applications at 5.15–5.35 GHz and 5.725–5.825 GHz). © 2006 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

To reduce side lobe level of slotted array antennas using nonuniform waveguides

In this article, a method is presented to reduce the side lobe level of slotted waveguide array antennas while the gain to be constant. In this method, the H‐plane dimension of the waveguide is considered as the variable rather than constant. The nonuniformity of waveguide walls obviates the need for offset of slots and thereby reduces the side lobe level of radiation pattern. A slotted nonuniform waveguide is designed at frequency 10 GHz and then fabricated and tested. © 2015 The Authors International Journal of RF and Microwave Computer‐Aided Engineering Published by Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:42–46, 2016.     

A broadband slant polarized cavity backed microstrip‐fed wide‐slot antenna array

This article deals with the design of a broadband cavity‐backed microstrip‐fed wide‐slot antenna array for L‐band applications. For verification purpose, a sample 1 × 4‐element antenna array has been designed, manufactured and tested. Experimental results have shown satisfactory agreement with the simulation. The proposed antenna array exhibits a measured impedance bandwidth of 1.4 GHz (90%) with frequency of 0.85 to 2.25 GHz and the gain is higher than 11 dBi. The designed antenna has small size and low weight and can be fabricated using a low‐cost fabrication process for easy integration with RF circuits and microwave components. This work is useful for some radar applications and radio frequency identification systems.     

Untilted slot array antenna at the narrow wall of the waveguide using double‐ridge

In this article a novel array antenna composed of untilted slots in the narrow wall of the double‐ridge waveguide, with significantly improved cross‐polarization, is presented. In the first step, suitable radiating elements for designing a linear slot array antenna were created. An untilted slot which is created the narrow wall of the double‐ridge waveguide is suggested to be used as the radiating resonance slot. The concave and convex ridges are located under the untilted slots only. It is shown that the concave and convex double ridge waveguides can produce an orthogonal current distribution in the place of the slots. They are also placed successively to produce the required phase inversion between adjacent slots. The linear array consists of nine uniform resonant untilted slots in the double ridge waveguide and is designed at the frequency of 5 GHz using the normalized conductance of each radiating slot. Analyzing the simulation results shows that cross‐polarization of the designed array was significantly improved, it was also found that the cross‐polarization and the SLL were respectively about ?65 and ?16 dB. © 2010 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2010.     

A new broadband circularly polarized square‐slot antenna with low axial ratios

A new broadband circularly polarized (CP) square‐slot antenna with low axial ratios is proposed in this article. The antenna is comprised of an L‐shaped microstrip line with tapered section and a square‐slot ground plane with some stubs and slots, which are utilized as perturbations for the desirable antenna performance. By loading stubs and slots in the square‐slot ground plane, the 2‐dB axial ratio bandwidth (ARBW) and 10‐dB return loss bandwidth for the presented antenna can be markedly improved. The measured results show that its 2‐dB ARBW is 4.2 GHz (54.2% from 5.65 GHz to 9.85 GHz) and its 10‐dB return loss bandwidth is about 8.9 GHz (92.7% from 5.15 GHz to 14.05 GHz). The proposed antenna features compact structure and broad 2‐AR bandwidth which could completely cover the WLAN (5.725‐5.85 GHz) band. Therefore, the proposed antenna is suitable for circular polarization applications in C band.     

Antipodal tapered slot antenna array using broadband decoupling structure for mutual coupling reduction

In this article, an effective method to reduce the mutual coupling between the antipodal tapered slot antenna (ATSA) array is proposed. This method is mainly implemented by loading a set of decoupling structures (DS) perpendicular to the dielectric substrate between two antenna elements. The proposed DS can provide transmission forbidden band which can effectively prevent leaked electromagnetic waves. DS can operate in most frequency bands within 4 to 17.5 GHz. It can enhance about 23 dB isolation between the ATSA array without affecting bandwidth and radiation characteristics. The proposed ATSA arrays are fabricated and tested. The measured results can verify its excellent properties. The proposed broadband decoupling method is a suitable candidate for restrain mutual coupling of ultra‐wideband planar end‐fire antennas. This design sheds new light on broadband decoupling.     

Design of a broadband dielectric resonator antenna and its application in low sensitivity frequency beam‐scanning array with wide scanning angle and suppressed sidelobes

In this paper, a broadband dielectric resonator antenna (DRA) with a simple H‐slot feeding structure is proposed. The broad bandwidth (~45%) and uni‐directional radiation enable this DRA suitable to work as a radiation element in the construction of a beam‐scanning array with not only low frequency sensitivity which is important for accurate angle estimation of in‐coming targets, but also a wide scanning range. Moreover, stable coupling coefficients are established around all the above three resonances with respect to its corresponding feeding line, ensuring a low sidelobe level (SLL) across the whole operating frequency range. In order to realize such a DRA, a latticed rectangular structure is utilized to generate the lower two resonances, while the upper resonance is generated by its H‐shaped feeding slot. The shape of the latticed dielectric resonator is also modified according to a 3‐D printed fixing structure for an accurate installation. A 20‐element beam‐scanning prototype is demonstrated and manufactured. The range of scanning angle is from ?36° to +13° within the bandwidth of 10 to 16 GHz, corresponding to a frequency sensitivity of only 122.5 MHz/^o. The achieved SLL are smaller than 19 dB for all scanning beams. The above performance indicates that, this array is very suitable for near‐range radar systems requiring an accurate angle estimation.     

A 60‐GHz on‐chip slot‐array antenna in integrated‐passive‐device technology for antenna‐in‐package applications

A new millimeter‐wave antenna structure on a low‐cost, production platform integrated passive device technology is presented. The antenna consists of a 2‐by‐1 array of slot antennas at 60 GHz. An in‐house developed on‐chip antenna measurement setup was used to characterize the fabricated antenna. The measurement results show an antenna gain of more than 5 dBi with a return loss of 18 dB at 60 GHz. The better‐than‐10‐dB impedance bandwidth of the antenna covers the 60‐GHz unlicensed band from 57 to 64 GHz. The 3‐dB beamwidths of the antenna are 105° and 76° at E‐plane and H‐plane at 60 GHz, respectively. The size of the die of the antenna is 2 mm × 4.5 mm. © 2013 Wiley Periodicals, Inc. Int J RF and Microwave CAE 24:155–160, 2014.     

Miniaturized dual‐band slot antenna design for GPS,amateur radio and WLAN applications

In this article, miniaturization of dual‐band slot antenna design for GPS, WLAN and amateur radio applications is presented. The proposed dual‐band miniaturized antenna is achieved using slits, rectangular split ring and metallic strips fed by 50 Ω microstrip feed. The first resonant frequency is achieved by loading reference antenna with eight slits that is antenna 1 and the second resonant frequency is achieved by loading with one center slits and rectangular split ring that is antenna 2. Dual‐band antenna is achieved by loading reference slot antenna with nine slits and rectangular split ring which resonates at frequency of 1.52 and 3.03 GHz respectively. As a result, it is achieved 53.79% reduction in first band resonant frequency with 76.07% improvement in ?10 dB bandwidth and 7.90% reduction in second band resonant frequency compared to reference slot antenna. Further, this dual‐band antenna is miniaturized by metallic strips which are placed on the bottom of the substrate. This results in 61.39% reduction in first band resonant frequency with 32.07% improvement in ?10 dB bandwidth and 26.13% reduction in second band resonant frequency in comparison with reference slot antenna topology.