Full‐color AMOLED with RGBW pixel pattern

Abstract— A full‐color AMOLED display with an RGBW color filter pattern has been fabricated. Displays with this format require about one‐half the power of analogous RGB displays. RGBW and RGB 2.16‐in.‐diagonal displays with average power consumptions of 180 and 340 mW, respectively, were characterized for a set of standard digital still camera images at a luminance of 100 cd/m². In both cases, a white‐emitting AMOLED was used as the light source, and standard LCD filters were used to provide the R, G, and B emission. The color gamuts of these displays were identical and the higher overall efficiency of the RGBW format results from two factors. First, a large fraction of a typical image is near neutral in color and can be reproduced using the white sub‐pixel. Second, the white sub‐pixel in an RGBW AMOLED display is highly efficient because of the absence of any color filter. The efficiency of these displays can be further enhanced by choosing a white emitter optimized to the target display white point (in this case D65). A two‐emission layer configuration based upon separate yellow and blue‐emitting regions is shown to be well suited for both the RGBW and RGB formats.     

Review Paper: Multi‐primary‐color displays: The latest technologies and their benefits

Abstract— Multi‐primary‐color (MPC) display technology is one of the fastest emerging research areas in recent years. Wide‐color‐gamut display devices have been required for visually sufficient and/or accurate color reproduction. It is well known that MPC displays can reproduce accurate colors with high efficiency. In addition, not only the image‐quality improvement but some other performance of display devices is also required for display devices. This paper reviews achievements in MPC display technologies and focuses on the benefits of MPC displays: power‐savings and high resolution.     

Comparison of organic and inorganic alignment layers for low‐power liquid‐crystal devices using low‐frequency applied‐voltage waveforms

Abstract— Bistable displays are known to have low‐power consumption, but they usually lack the ability to display full‐color video‐rate images. Operating active‐matrix liquid‐crystal displays (AMLCDs) with an ultra‐wide refresh‐rate range, down to ～1 Hz, can lower the power consumption to that of bistable devices and offer video rates as well. A SiO^x‐layer‐based liquid‐crystal (LC) alignment technique is studied here to overcome the ion problems typically encountered with low‐refresh‐rate devices. The effect of ions on the voltage‐holding ratio (VHR) and residual DC voltage (RDC) with SiO^x‐based LC alignment is compared with those for polyimide‐based LC alignment. It is found that only SiO^x alignment provides high VHR and small RDC, with good stability over time. Therefore, it is shown that SiO^x alignment is an excellent candidate for low‐power AMLCDs operated with an ultra‐wide refresh‐rate range.     

Towards a low‐cost high‐quality carbon‐nanotube field‐emission display

Abstract— We have developed field‐emission‐display technology driven by chemical‐vapor‐deposition‐grown carbon‐nanotube emitters incorporated in a simple, low‐cost device structure. Here, we report on frit‐sealed test displays with a brightness of 3000 cd/m² at 3 kV and a lifetime of 9000 hours with only 45% degradation. We also demonstrate the scalability of the technology with a uniform high‐brightness 6‐in. QVGA that displays video images with a switching voltage of 40 V.     

Video 2‐D—to—3‐D conversion based on hybrid depth cueing

Abstract— With the maturation of three‐dimensional (3‐D) technologies, display systems can provide higher visual quality to enrich the viewer experience. However, the depth information required for 3‐D displays is not available in conventional 2‐D recorded contents. Therefore, the conversion of existing 2‐D video to 3‐D video becomes an important issue for emerging 3‐D applications. This paper presents a system which automatically converts 2‐D videos to 3‐D format. The proposed system combines three major depth cues: the depth from motion, the scene depth from geometrical perspective, and the fine‐granularity depth from the relative position. The proposed system uses a block‐based method incorporating a joint bilateral filter to efficiently generate visually comfortable depth maps and to diminish the blocky artifacts. By means of the generated depth map, 2‐D videos can be readily converted into 3‐D format. Moreover, for conventional 2‐D displays, a 2‐D image/video depth perception enhancement application is also presented. With the depth‐aware adjustment of color saturation, contrast, and edge, the stereo effect of the 2‐D content can be enhanced. A user study on subjective quality shows that the proposed method has promising results on depth quality and visual comfort.     

The luminance resolution characteristics of multi‐primary‐color display

Abstract— In this paper, the resolution characteristics of multi‐primary‐color (MPC) display systems are analyzed. That four‐primary‐color (4PC) displays can increase the effective resolution for achromatic images in the luminance domain by a factor of two as compared to conventional RGB‐based displays with MPC‐specialized subpixel rendering, which is proposed in this paper, is demonstrated. Five‐ and six‐primary‐color (5PC and 6PC) display systems can reproduce denser luminance data than conventional RGB‐based display systems and solve a problem of MPC displays, viz. an increase of production costs and a decrease in the aperture ratio caused by increasing the number of subpixels in one pixel. This is an essential advantage of MPC display systems, which is related to the combination of the proposed color‐filter architecture and image processing. Thus, a completely new advantage of MPC display systems, in addition to their well‐known capabilities of color reproduction and power saving, is proposed.     

A field‐sequential‐color display with a local‐primary‐desaturation backlight scheme

Abstract— Field‐sequential‐color technology eliminates the need for color filters in liquid‐crystal displays (LCDs) and results in significant power savings and higher resolution. But the LCD suffers from color breakup, which degrades image quality and limits practical applications. By controlling the backlight temporally and spatially, a so‐called local‐primary‐desaturation (LPD) backlight scheme was developed and implemented in a 180‐Hz optically compensated bend (OCB) mode LCD equipped with a backlight consisting of a matrix of light‐emitting diodes (LEDs). It restores image quality by suppressing color breakup and saves power because it has no color filter and uses local dimming. A perceptual experiment was implemented for verification, and the results showed that a field‐sequential‐color display with a local‐primary‐desaturation backlight reduced the color breakup from very annoying to not annoying and even invisible.     

Active matrix monolithic micro‐LED full‐color micro‐display

An active matrix monolithic micro‐LED full‐color micro‐display with a pixel density of 317 ppi is demonstrated. Starting from large‐scale and low‐cost GaN‐on‐Si epilayers, monolithic 64 × 36 blue micro‐LED arrays are fabricated and further transformed to full‐color micro‐displays by applying a photo‐patternable color conversion layer. This full‐color fabrication scheme shows feasible manufacturability, suggesting a potential for volume production of micro‐LED full‐color micro‐display.     

Design of carbon nanotubes for large‐area electron field‐emission cathodes

Abstract— Electron field‐emission displays offer a viable option for the next generation of flat‐panel screens. Boasting high‐quality images in terms of good color saturation, fast refresh rate, and high brightness, these displays have the potential to offer above and beyond what the current market leaders, LCD and plasma. However, for the realization of such a new display disrupting the incumbent LCD and plasma displays, not only does the image quality need to be better, but fabrication costs and suitable manufacturing processes need to be in place at reduced cost. Many viable cathode materials have been proposed in recent years, one of which being the use of carbon nanotubes (CNTs) in various forms (aligned growth, screen printing, and polymer matrix). In this review, a series of recent experiments investigating the field‐emission characteristics of carbon‐nanotube systems for possible use in the display industry is presented.     

Performance of liquid‐crystal displays for fire‐service thermal‐imaging cameras

Abstract— As use of handheld thermal‐imaging cameras (TICs) becomes more prevalent in the first‐responder community, it is important that standard test metrics be available to characterize imaging performance. A key performance consideration is the quality of the image presented on the TIC display. This paper focuses on TICs that use liquid‐crystal displays to render an image for the user. Current research on TIC performance for first‐responder applications makes use of trained observers and/or composite‐video‐output‐signal measurements. Trained observer tests are subjective and composite video output tests do not evaluate the performance of the complete imaging system. A non‐destructive objective method was developed that tests the performance of the entire thermal‐imaging system, from the infrared sensor to the display. A thermal target was used to correlate the measured thermal imager composite video output signal with the luminance of the display. A well‐characterized charge‐coupled‐device (CCD) camera and digital recording device were used to measure the display luminance. An electro‐optical transfer function was determined that directly relates the composite video output signal to the luminance of the display, providing a realistic characterization of system performance.     

Moiré‐reduction methods for integral videography autostereoscopic display with color‐filter LCD

Abstract— Moiré‐reduction methods for integral videography displays are proposed. Integral videography is based on the principles of integral photography and extended real‐time video processing. There are two moiré‐reduction methods that can be used for integral videography displays that have a lens array and a liquid‐crystal display. The first is color moiré, and the second is intensity moiré. To reduce color moiré, an optimized color‐filter layout in the liquid‐crystal display was used. To reduce intensity moiré, a defocusing method was used. Adesign of a viewing area for the integral videography display is also presented. To control the viewing area, the lens pitch and the shape of the integral videography elemental image was changed. A 5‐in. integral videography display was implemented by using the proposed methods, and an integral videography display was evaluated.     

Driving large‐sized OLED TVs with an amorphous‐silicon backplane

Abstract— A 20‐in. OLED display driven by an amorphous‐silicon backplane has been demonstrated. It has been widely believed that the characteristics of amorphous‐silicon TFTs are not sufficient to drive OLED display. This paper challenges this hypothesis and proves that amorphous silicon can be applied to large active‐matrix‐driven displays and discusses many possible approaches that lead to good front‐of‐screen quality. Superior‐video‐image‐quality amorphous‐silicon‐driven OLEDs opens a bright future for a new generation of wall‐hanging televisions.     

Fluorescent‐based tandem white OLEDs designed for display and solid‐state‐lighting applications

Abstract— Highly efficient tandem white OLEDs based on fluorescent materials were developed for display and solid‐state‐lighting (SSL) applications. In both cases, the white OLED must have high power efficiency and long lifetime, but there are a number of attributes unique to each application that also must be considered. Tandem OLED technology has been demonstrated as an effective approach to increase luminance, extend OLED lifetime, and allow for use of different emitters in the individual stacks for tuning the emission spectrum to achieve desired performance. Here, examples of bottom‐emission tandem white OLEDs based on small‐molecule fluorescent emitters designed for displays and for SSL applications are reported. A two‐stack tandem white OLED designed for display applications achieved 36.5‐cd/A luminance efficiency, 8500K color temperature, and lifetime estimated to exceed 50,000 hours at 1000 cd/m². This performance is expected to meet the specifications for large AMOLED displays. A two‐stack tandem white OLED designed for SSL applications achieved 20‐lm/W power efficiency, 38‐cd/A luminance efficiency, 3500K color temperature, and lifetime estimated to exceed 140,000 hours at 1000 cd/m². With the use of proven light‐extraction techniques, it is estimated that this tandem device will exceed 40 lm/W with more than 500,000‐hour lifetime, performance that should be sufficient for first‐generation lighting products.     

Color‐by‐Blue: A novel method to achieve full‐color inorganic EL displays

Abstract— A new method for achieving full‐color capability for inorganic EL displays was developed, which combines electroluminescence with photoluminescence phenomena in the same device structure. In this display panel, the blue emission was obtained from the EL device by using the Eu‐doped barium thioaluminate phosphor material system, which was then used to generate green and red emission by the use of down‐conversion materials. The major advantages of the Color‐by‐Blue method (CBB) are the elimination of color‐balance control issues associated with the use of different electroluminescent phosphor materials for red, green, and blue with potentially different threshold voltages for the onset of luminance and the achievement of a low‐cost high‐yield manufacturing process.     

Color displays and flexible displays using quick‐response liquid‐powder technology for electronic paper

Abstract— Color displays and flexible displays that use electronic liquid powder have been developed. Novel types of color displays using either a colored powder or a color filter are discussed. We have also developed a flexible display with low‐cost substrate films with a high‐throughput roll‐to‐roll manufacturing method. These technologies enable a QR‐LPD to be widely used as an electronic‐paper display.     

In‐field evaluation of the modulation transfer function and the signal‐to‐noise ratio of electronic‐display devices

Abstract— This paper describes a charged‐coupled device (CCD) camera, which was developed for in‐field evaluation of the image quality of electronic‐display devices [such as cathode‐ray tubes (CRTs) and liquid‐crystal displays (LCDs)] used for medical applications. Contrary to traditional cameras for display‐image‐quality evaluation, this CCD camera does not require a sophisticated x‐y‐z translation stage for mounting and adjustment. Instead, it is handheld and pressed by gentle pressure against the display screen. It is controlled by a software package which was originally developed for display calibration according to the DICOM 14 gray‐scale standard display function (GSDF). This software package controls the camera gain when measurements are made at different display luminance, display test patterns, performs image analysis and displays the results of the measurements and calculations. The work concentrated on the measurement of modulation transfer function (MTF) and of signal‐to‐noise ratio (SNR) per display pixel. The MTF is derived from the Fourier transform of the line spread function (LSF). The single‐display‐pixel SNR is derived from the integration of the noise power spectrum (NPS) of a camera image taken of a display with a uniform luminance. It is demonstrated that the device can produce repeatable results in terms of MTF and SNR. MTFs were measured on three monochrome CRTs and five monochrome LCDs in order to study repeatability and similar quantities. The MTF was measured on a 5‐Mpixel LCD yielding values that lie within 3.5% of the average MTF at the Nyquist frequency and 4.0% of the maximum total sharpness (∫ MTF² df). The MTF was also measured on a 9‐Mpixel LCD, yielding values that lie within 9.0% of the average MTF at the Nyquist frequency and 8.0% of the maximum total sharpness. The SNR was measured eight times on a 3‐Mpixel monochrome LCD at nine digital driving levels (DDLs). At a DDL of 185, the mean SNR was 15.694 and the standard deviation (Stdv) was 0.587. At a DDL of 65, the mean SNR was 5.675 and Stdv was 0.120.     

An active‐matrix organic light‐emitting‐diode pixel circuit for the compensation of I × R voltage drop in power line

Abstract— A new voltage‐driving active‐matrix organic light‐emitting diode (AMOLED) pixel circuit is proposed to improve the display image‐quality of AMOLED displays. Because OLEDs are current‐driven devices, the I × R voltage drop in the power lines is evitable. Accordingly, the I × R voltage‐drop compensation scheme should be included in the pixel‐driving method when a voltage‐compensation method is used. The proposed pixel was designed for the compensation of an I × R voltage drop in the power lines as well as for the compensation of the threshold‐voltage non‐uniformity of low‐temperature polycrystalline‐silicon thin‐film transistors (LTPS TFTs). In order to verify the compensation ability of the proposed pixel, SPICE simulation was performed and compared with those of other conventional pixels. When the Vss voltage varies from 0 to 1 V, the drain current of the proposed pixel decreased by under 1% while that of conventional Vth compensation methods without Vss compensation decreased by over 60%. 2.2‐in. QCIF⁺ full‐color AMOLED displays, which employ the proposed pixel, have been also developed. It was verified by comparison of the display image quality with a conventional panel that our proposed panel successfully overcame the voltage‐drop problems in the power lines.     

High‐luminance 1.8‐mm‐pixel‐pitch CNT‐FED for ubiquitous color character displays

Abstract— A high‐luminance 1.8‐mm‐pixel‐pitch CNT‐FED for color character displays has been developed. The display panel has 32 × 256 color pixels, and the subpixel size is 0.6 × 1.8 mm. The display panel can provide good visibility when installed even in outdoor locations. The power consumption is low enough for the display to be battery driven. The practical application is the display of important messages regarding the evacuation from disaster areas, even under emergent no‐power conditions similar to the messages on vending machines.     

A carbon‐nanotube field‐emission display with simple electron‐beam trajectory control

Abstract— A unique gated cathode structure for a carbon‐nanotube‐based field‐emission display has been designed and built. This structure optimizes the electron‐beam profiles to assure a good color gamut and high anode efficiency without requiring specific focusing electrodes or structure. A computer simulation, written to analyze and improve the device design, shows good correlation with the experimental data and helps predict design margins. A full‐color frit‐sealed display built with this approach demonstrates an excellent color gamut of the phosphor, and the model predicts avenues for further color‐gamut improvements.     

Color plastic bistable nematic display fabricated by imprint and ink‐jet technology

Abstract— Plastic displays require new manufacturing processes and techniques to achieve acceptable cost and performance. A novel additive, low‐temperature atmospheric‐pressure self‐aligned means of fabricating integrated plastic substrates for full‐color LCDs and a bistable LC mode based on microstructure alignment are presented. By using imprinting rather than photolithographic patterning, a scalable, low‐cost manufacturing route is possible. A 2‐in.‐diagonal 128 × 128‐pixel display was made to demonstrate the principles involved, which has retained an image for in excess of 2 years.