Characterizations of VO2-based uncooled microbolometer linear array

Vanadium dioxide (VO₂) thin films are materials for uncooled microbolometer due to their high temperature coefficient of resistance (TCR) at room temperature. This paper describes the design and fabrication of eight-element uncooled microbolometer linear array using the films and micromachining technology. The characteristics of the array is investigated in the spectral region of 8–12 μm. The fabricated detectors exhibit responsivity of over 10 kV/W, detectivity of approximate 1.94×10⁸ cm Hz^1/2/W, and thermal time constant of 11 ms, at 300 K and at a frequency of 30 Hz. Furthermore, the uncorrected response uniformity of the linear array bolometers is less than 20%.     

Adsorptive voltammetry of Hg(II) ions at a glassy carbon electrode coated with electropolymerized methyl-red film

The glassy carbon electrode coated with electropolymerized methyl-red film, 1.2 × 10⁻⁶ m in thickness, (PMRE) showed high sensitivity towards Hg(II) ions. PMREs were adopted to accumulate and detect Hg(II) ions in a pH 2.56 Britton–Robinson buffer solution. Cyclic voltammogram of the accumulated Hg species on PMREs exhibited an anodic wave at 0.64 V and a cathodic wave at 0.13 V, due to the oxidation of accumulated Hg species on PMREs and the reduction of Hg(II) ions in the solution, respectively. For this heterogeneous adsorption of Hg(II) ions onto PMREs, the maximum surface concentration, adsorption equilibrium, and Gibbs energy change were evaluated to be 5.12 × 10⁻⁶ mol m⁻², 3.7 × 10⁵ l mol⁻¹, and −30.1 kJ mol⁻¹, respectively. The anodic peak current at 0.64 V was linear with the concentration of Hg(II) ions in the range of 1.1 × 10⁻¹⁰ to 1.1 × 10⁻⁷ M with a detection limit of 4.4 × 10⁻¹¹ M. The proposed method was utilized successfully for the detection of Hg(II) ions in the lake water.     

Pyroelectric and dielectric properties of sol–gel derived barium–strontium–titanate (Ba0.64Sr0.36TiO3) thin films

The barium–strontium–titanate (BST, Ba_0.64Sr_0.36TiO₃) thin films have been prepared by the sol–gel method on a platinum-coated silicon substrate. The resulting thin films show very good dielectric and pyroelectric properties. The dielectric constant and dissipation factor for Ba_0.64Sr_0.36TiO₃ thin film at a frequency of 200 Hz were 592 and 0.028, respectively. The dependence of the capacitance as a function of the voltage shows a strongly non-linear character, and two peaks characterizing spontaneous polarization switching can be clearly seen in this curve, indicating that the films have a ferroelectric nature. The capacitance changed from 495 to 1108 pF with the applied voltage in the −5 to +5 V range at a frequency of 100 kHz. The peak pyroelectric coefficient at 30 °C is 1080 μC/m² K. The pyroelectric coefficient at room temperature (25 °C) is 1860 μC/m² K, and the figure-of-merit of this film is 37.4 μC/m³ K. The high pyroelectric coefficients and the greater figures-of-merit of Ba_0.64Sr_0.36TiO₃ thin films make it possible to be used for thermal infrared detection and imaging.     

Room temperature hydrogen response kinetics of nano–micro-integrated doped tin oxide sensor

The nano–micro-integrated sensor has been fabricated by sol–gel depositing the nanocrystalline indium oxide (In₂O₃)-doped tin oxide (SnO₂) thin film on microelectromechanical systems (MEMS) device having interdigitated electrode configurations with two different electrode spacing (10 μm and 20 μm) and two different number of fingers (8 and 20). The present nano–micro-integrated sensor exhibits high H₂ sensitivity range (S = 3–10⁵) for the H₂ concentration within the range of 100–15,000 ppm at room temperature. It has been demonstrated that, the room temperature response kinetics of the present nano–micro-integrated sensor is a function of finger spacing, H₂ concentration and air-pressure, but independent of number of fingers. Such dependence has been explained on the basis of Le Chatelier's principle applied to the associated H₂ sensing mechanism and the role of above parameters in shifting the dynamic equilibrium of the involved surface reactions under the described test conditions. A new definition of the response time has been proposed, which is not only suitable for the theoretical analysis but also for the practical applications, where a gas-leak detection alarm is required to be triggered.     

Development of a highly sensitive and selective optical chemical sensor for batch and flow-through determination of mercury ion

A very sensitive, highly selective and reversible optical chemical sensor (optode) for mercury ion is described. The sensor is based on the interaction of Hg²⁺ with 2-mercapto-2-thiazoline (MTZ) in plasticized PVC membrane incorporating a proton-selective chromoionophore (ETH5294) and lipophilic anionic sites (sodium tetraphenylborate, NaTPB). The membranes were cast onto glass substrates and used for the determination of mercury ion in aqueous solutions by batch and flow-through methods. The sensor could be used in the range 2.0 × 10⁻¹⁰ to 1.5 × 10⁻⁵ M (0.04 ng mL⁻¹ to 3 μg mL⁻¹) Hg²⁺ with a detection limit of 5.0 × 10⁻¹¹ M and a response time of <40 s. It can be easily and completely regenerated by dilute nitric acid solution. The sensor has been incorporated into a home-made flow-through cell for determination of mercury ion in flowing streams with improved sensitivity, precision and detection limit. The sensor showed excellent selectivity for Hg²⁺ with respect to several common alkali, alkaline earth and transition metal ions. The results obtained for the determination of mercury ion in river water samples using the proposed optode was found to be comparable with the well-established cold-vapor atomic absorption method.     

3-D silicon vector sensor based on a novel parallel-field Hall microdevice

A single-chip 3-D silicon vector sensor for magnetic-field measurement is presented. This triaxial device functionally integrates in a common transducer region two novel five-contacts parallel-field Hall elements for in-plane components B_x and B_y and four cross-coupled orthogonal triple Hall elements for the B_z component, perpendicular to the chip surface. The effective sensor volume is 150 μm×150 μm×100 μm. The main advantage of this 3-D vector magnetometer is the strongly reduced (with about 45%) channel cross-sensitivities. This is achieved by amperometric output mode of operation using an original read-out circuitry, keeping equal voltage conditions on the top of the chip with and without magnetic field. The sensitivities per channel reaches S_A(B_x)=S_A(B_y)=356 μA/T and S_A(B_z)=260 μA/T at a supply current 10 mA, the measured equivalent offsets of the three channel outputs are 25/35 mT and the low frequency noise is mainly a 1/f. The lowest detected magnetic induction of the three output channels is about 15/20 μT in the range 1≤f≤ 10² Hz and the frequency response of the 3-D device together with the read-out electronics is at least 30 kHz.     

Direct electrochemistry and electrocatalysis of myoglobin immobilized in zirconium phosphate nanosheets film

Myoglobin (Mb) is incorporated on a novel matrix—zirconium phosphate nanosheets (ZrPNS) and immobilized at a glassy carbon electrode surface. UV–vis spectra and electrochemical measurements show that the matrix is well biocompatible and can retain the bioactivity of immobilized Mb. The direct electron transfer between Mb and electrode exhibits a couple of well-defined redox peaks. The cathodic and anodic peaks are located at −0.340 and −0.280 V vs. Ag/AgCl, respectively. The ZrPNS can improve the electron transfer between Mb and electrode with an electron transfer constant of 5.6 s⁻¹. Meanwhile, the catalytic ability of the protein toward the reduction of H₂O₂, O₂, NaNO₂, trichloroacetic acid (TCA) is also studied and a third-generation biosensor is subsequently fabricated. The linear range of biosensor to H₂O₂ is from 8 × 10⁻⁷ to 1.28 × 10⁻⁵ M with the limit detection of 1.4 × 10⁻⁷ M. The small apparent Michaelis–Menten constant (34 μM) suggests that Mb/ZrPNS film performs good affinity with H₂O₂. The biosensor also exhibits acceptable stability and reproducibility. This work paves a way to develop other biologic active materials in this kind of nanosheets for constructing novel biosensors.     

Precise isotope abundance ratio measurement of nitrous oxide using diode lasers

High-precision measurement of the isotope abundance ratio ¹⁴N¹⁵N¹⁶O/¹⁵N¹⁴N¹⁶O/¹⁴N¹⁴N¹⁸O/¹⁴N¹⁴N¹⁶O (0.37/0.37/0.2/100) in nitrous oxide by a laser-spectroscopic method is demonstrated. The abundance ratio is determined from the absorbance ratio of selected absorption lines near 2 μm of the respective isotopic molecular species. Four wavelength-modulated diode lasers whose center wavelengths are stabilized on the selected lines are made to travel different distances in a multipass cell to compensate the large abundance differences. In the test experiment using pure nitrous oxide samples the abundance ratio can be measured with relative uncertainties of ±(2–6)×10⁻⁴ (±0.2–0.6‰). The laser-spectroscopic method is expected to complement mass spectrometry in isotope analyses to trace the geochemical cycles of environmental substances.     

Perchlorate selective membrane electrodes based on synthesized platinum(II) complexes for low-level concentration measurements

Three synthesized platinum(II) complexes, [PtR₂(NN)] (R = Me, p-MeC₆H₄ and p-MeOC₆H₄; NN = 2,2′-bipyridyl), were studied to characterize their ability as an anion carrier in a PVC membrane electrode. The polymeric membrane electrodes (PME) and also coated glassy carbon electrodes (CGCE) prepared with [Pt(p-MeOC₆H₄)₂(NN)] showed excellent response characteristics to perchlorate ions. The electrodes exhibited Nernstian responses to ClO₄⁻ ions over a wide concentration range from 5 × 10⁻⁷ to 4.0 × 10⁻¹ M for PME and 1.5 × 10⁻⁷ to 2.7 × 10⁻¹ M for CGCE with low detection limits (4.0 × 10⁻⁷ M for PME and 1.0 × 10⁻⁷ M for CGCE). The electrodes possess fast response time, satisfactory reproducibility, appropriate lifetime and, most importantly, good selectivity toward ClO₄⁻ relative to a variety of other common anions. The potentiometric response of the electrodes is independent of the pH of the test solution in the pH range 2.5–9.5. The proposed sensors were used in potentiometric determination of perchlorate ions in mineral water, urine samples and also samples containing interfering anions. The interaction of the ionophore with perchlorate ions was shown by UV–vis spectroscopy.     

Electrocatalytic oxidation of methanol and other short chain aliphatic alcohols on glassy carbon electrodes modified with conductive films derived from Ni-(N,N′-bis(2,5-dihydroxybenzylidene)-1,2-diaminobenzene)

Complexes of nickel(II) with the ligand N,N′-bis(2,5-dihydroxybenzylidene)-1,2-diaminobenzene (Ni^II-DHS) can be electropolymerized onto glassy carbon surfaces in alkaline solution to give electroactive films strongly adhered on the electrode surface. In alkaline solution, these poly-[Ni^II-DHS]/GC films present the typical voltammetric response of a surface-immobilized redox couple, as can be anticipated for the Ni²⁺/Ni³⁺ transitions into the film. In addition, the films exhibit a potent and persistent electrocatalytic activity towards the oxidation of methanol. The electrocatalytic currents are, at least, 80 times higher than those obtained for the oxidation of methanol at electrodes modified with nickel hydroxide films in alkaline solutions. In addition, the current is proportional to the concentration of methanol from 0.050 to 0.30 μM. The detection limit and the sensitivity were found to be 26 ± 2 nM and 7.4 × 10⁻² ± 6 × 10⁻³ A cm² mol⁻¹ M⁻¹, respectively. Electrodes modified with poly-[Ni^II-DHS]/GC films show a moderate electrocatalytic activity towards the oxidation of other aliphatic short chain alcohols, such as: ethanol, 1-propanol, 2-propanol and n-butanol. In all cases the catalytic currents present linear dependences with the concentration of alcohol in alkaline solution. The analytical properties of these potential alcohol sensors have also been studied.