首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 125 毫秒
1.
研究某轿车动力学模型优化,多体动力学理论,采用虚拟样机技术,对车辆行驶的平顺性,建立包含前后悬架、转向系统、车轮、制动系统、车身等在内的整车多体动力学虚拟样机模型,依据国家标准,在ADAMS/Car Ride中成功地对轿车进行脉冲输入和随机路面输入的平顺性仿真,得到的数据输入到MATLAB编制的平顺性评价程序中。对比结果表明,车平顺性较好。在此基础上,并将整车模型简化为二自由度1/4车辆模型,在Matlab/Simulink上建立振动模型,分析了悬架刚度、阻尼比、轮胎刚度对车辆平顺性的影响,得出车身加速度随悬架刚度、阻尼比及轮胎动载荷变化的规律。  相似文献   

2.
为了对矿用自卸车主动油气悬架进行有效控制,分析了其油气弹簧的刚度力与阻尼力的非线性特性,进而建立了两自由度油气悬架的非线性力学模型。应用微分几何线性化理论,经过恰当的坐标变换和反馈控制,实现非线性系统的精确线性化,而后对其设计使用线性PID控制研究;根据选定的控制目标及输出变量,通过制定相应的模糊控制规则表,设计模糊PID控制器,对悬架系统使用模糊PID控制研究。仿真结果表明,与被动悬架相比,精确线性化后的PID控制悬架以及模糊PID控制悬架均能显著提高车辆的平顺性和操稳性,使悬架的动态性能趋于稳定;另外,与模糊PID控制相比,线性化PID控制对于改善车辆行驶平顺性优势更加明显。  相似文献   

3.
为了提高在矿山路面的行驶平顺性与安全性,建立了矿用汽车1/4车辆半主动油气悬架动力学模型,并分析了油气悬架弹性力和阻尼力的非线性特性;在微分几何理论的基础上,利用状态反馈线性化方法实现非线性模型精确线性化,应用最优控制理论设计了LQG控制器,并采用层次分析法确定LQG控制的各性能指标的加权系数;仿真结果表明:经层次分析法合理选择加权系数后,车身加速度、悬架动行程及轮胎动位移等分别较被动油气悬架降低了42.6%、21.9%和27.3%,显著提高了车辆在矿山路面的行驶平顺性、操稳性以及安全性。  相似文献   

4.
论文通过建立1/4车体两自由度半主动悬架模型,设计了双输入单输出的模糊PID控制器,并在Matlab/Simulink环境下对半主动悬架系统进行了仿真研究。研究结果表明,与被动悬架系统和基于PID控制的半主动悬架系统相比较,基于模糊PID控制的汽车半主动悬架系统能够有效地降低车身的垂直加速度,并能提高车辆的平顺性,减小轮胎的动载荷。最后对基于模糊PID控制的半主动悬架系统在同一路面等级不同车速下进行了仿真研究,结果表明随着车速的增加车辆的平顺性、操纵稳定性以及安全性都会下降。  相似文献   

5.
针对轮毂电机驱动的电动汽车簧下质量的增加导致车辆平顺性下降的问题,采用与轮辋连接的三个对称分布的减振器和弹簧作为驱动电机悬架,主动轮与车体之间仍采用原车悬架结构.建立含路面激励与电机振动激励的车辆1/4垂向振动数学模型,采用B级路面作为路面激励,以0阶和8阶电磁力波作为电机振动激励.实例仿真研究双激励下的车身加速度、车轮动载荷、悬架动挠度以及电机位移等响应,比较不同车速下的系统响应,分析电机悬架参数对系统响应的影响.结果 表明,电机振动激励对系统有一定的影响,路面输入是振动的主要来源,电机悬架阻尼系数的影响大于弹簧刚度的影响,上述悬架构型在宽车速范围内都表现出良好的减振性能.  相似文献   

6.
建立了基于连通式油气悬架的三轴重型车辆模型,分别将路面不平度考虑为冲击激励、随机激励和正弦激励,分析了连通式油气悬架的非线性特性对三轴重型车辆振动特性的影响,并分析了连通式油气悬架的抗俯仰性能及抗侧倾性能;将路面不平度考虑为正弦激励,以路面不平度激励频率为参数,通过分叉图、波形图、相图以及庞加莱截面分析了正弦激励作用下三轴重型车辆的非线性动力学响应,仿真结果表明系统在不同激励条件下存在周期运动和混沌运动;连通式油气悬架对重型车辆具有较好的抗侧倾和俯仰特性.  相似文献   

7.
车辆主动悬架模糊控制器的设计及其仿真分析   总被引:9,自引:0,他引:9  
兰波  喻凡 《计算机仿真》2003,20(7):59-61,64
该文通过车辆悬架系统和路面输入模型的建立,应用模糊逻辑控制理论,进行了车辆主动悬架模糊控制器的设计,并在Matlab/Sirmulink环境中对此模糊控制器进行了仿真,把它与传统的被动悬架和用LQG控制器控制的主动悬架作了比较及性能分析,仿真结果证明了相对于其它两种悬架来说,具有模糊控制器作用的主动悬架在降低车身加速度、改善车辆的行驶平顺性和乘坐舒适性上有显著的效果。  相似文献   

8.
基于软土路面的越野车辆平顺性研究   总被引:2,自引:0,他引:2  
研究不同路面上行驶越野车平顺性问题,针对软土路面振动特性,为了准确的仿真和预测越野车在软土路面上的平顺性,通过基于载荷沉陷理论开发出用于计算弹性轮胎-软土路面接触力的ADAMS用户子程序,在某越野车整车虚拟样机模型中实现了弹性轮胎与软土路面之间非线性接触仿真,再改变子程序中软土路面相关参数对越野车进行随机输入行驶试验仿真,仿真结果表明,随着路面变形的增大,轮胎动载荷,悬架动挠度均有较大变化,车身的振幅有显著增大,说明适应于硬地面的悬架不适应于软土路面.通过模型能够较准确地仿真由于路面变形对整车平顺性的影响,为设计提供了科学依据.  相似文献   

9.
该文研究内容为车辆(轮式、履带)在不平路面行驶和通过障碍时的平顺性问题。利用状态方程法建立了包括随机和确定路面轮廓、三维车体等较为通用的车辆行驶平顺性模型,并针对行驶振动中车轮与悬架的碰撞建立了专门模型。对某型装甲车辆进行了计算机仿真和验证,对模型的精度和有效性进行检验和评估。结果证明所建立的车辆-地面系统模型是有效的。该模型和建模采用的方法为装甲车辆的系统设计和动力学分析提供了一条途径。  相似文献   

10.
考虑到空气弹簧的非线性特性,建立了2自由度车辆空气悬架系统的振动模型.为了提高车辆行驶平顺性和乘坐舒适性,设计将粒子群优化(Particle Swarm Optimization,PSO)算法与PID控制策略相结合后应用于车辆空气悬架系统控制,并在Matlab/Simulink环境下,对不同车速和行驶路况下的车辆空气悬架进行了仿真分析.仿真结果表明:与传统的PID控制比较,基于粒子群优化的PID控制器使得车辆空气悬架系统的车身垂向加速度(BA),悬架动行程(sws)和轮胎动位移(DTD)的均方根值都有所减少,改善了车辆的平顺性和操纵稳定性.  相似文献   

11.
A linear quadratic (LQ) based controller and observer concept for a semi-active full-car model is implemented and compared to a skyhook controller using a real vehicle in this paper. Especially an observer including a new modified road model is presented, which reliably filters low frequency disturbances induced by ascending or descending steep hills. Furthermore, methods for the parametrization of the quadratic cost function are presented and it is shown in experiments for different vehicle masses that ride comfort and road holding can be significantly improved by using semi-active suspension control. In order to take nonlinear component characteristics or suspension friction into account a parametrized nonlinear full-car model is presented, which is used for the determination of the controller cost function weights. The performance evaluation is done using a 4-poster test rig as well as measurements conducted on a real road.  相似文献   

12.
Robust impedance control of a hydraulic suspension system   总被引:1,自引:0,他引:1  
A novel robust impedance control approach is developed to control dynamic behavior of a vehicle subject to road disturbances. This behavior is predetermined as an impedance rule to achieve passenger comfort and vehicle handling by the use of a hydraulically actuated suspension system. Impedance control law is simple, free of model and efficient to apply for a broad range of road conditions. Moreover, it relates comfort to handling. This control approach can provide a desired comfort when passing a bump, and both desired comfort and handling after passing a bump. Robust position and force controls are used to implement the robust impedance control with the presence of uncertainties. A transformed proportional–integral–derivative control is proposed to perform the robust control. The system stability is analyzed and analytical results are confirmed by simulations. A quarter‐car model of suspension system and a nonlinear model of hydraulic actuator are used to simulate the control system. Copyright © 2009 John Wiley & Sons, Ltd.  相似文献   

13.
汽车脉冲输入平顺性的仿真分析   总被引:5,自引:0,他引:5  
该文讨论了运用虚拟样机技术 ,进行汽车脉冲输入平顺性仿真分析的方法 ,针对本校研制的电动牵引车建立了包括悬架、车体和人 -椅系统在内的多体系统模型 ,并通过建立轮胎的UA解析模型和三维路面模型来计算轮胎与地面的相互作用。通过仿真试验 ,对该车的平顺性能进行了评价 ,分析了悬架和座椅参数对该车平顺性的影响 ,从而实现了在该车的设计阶段 ,对其平顺性进行预测及分析的目的。  相似文献   

14.
吴慧峰 《计算机仿真》2012,29(3):363-366
汽车悬架直接影响汽车在行驶过程中抑制不平路面对车身的冲击力及车身倾斜度,传统被动悬架遇冲击自动调节能力较差,抗振能力不强,针对上述问题,通过对悬架受力特点分析,建立了1/4车体二自由度主动悬架数学模型,结合自动控制理论,设计车辆的主动悬架模糊控制器,利用MATLAB/Simulink模糊工具箱对其进行仿真,在相同输入的情况下,对主动悬架与被动悬架模型部分性能参数分析比较,仿真结果表明采用此模糊控制器的主动悬架在提高车辆乘坐的舒适性和操纵的稳定性方面明显优于被动悬架。实验证明,研究结果对汽车主动悬架系统的设计具有一定参考价值。  相似文献   

15.
基于半主动悬架车辆的1/4动力学模型,论述了磁流变液特性及磁流变减振器的工作原理,推导了在随机最优控制理论下可调阻尼力和状态变量之间的关系,应用matlab/simulink编制了人车路模型的仿真程序,并以简化模型为例,考察了在磁流变阻尼器控制下的人车路平顺性问题.计算结果表明,与没有磁流变减振器的被动悬架相比较,该减振器的应用能够较好的改善汽车的平顺性,对提高人体的舒适性以及进一步深入研究该系统的振动,改善道路的振动特性有一定的指导意义.  相似文献   

16.
为了协调高速铁道车辆的运动稳定性与曲线通过性能之间的矛盾,本文采用多目标优化方法对一种高速铁道车辆的关键悬挂参数进行了优化处理.采用多体动力学技术建立了某型高速铁道车辆62个自由度的动力学模型,模型考虑了轮轨接触几何非线性、轮轨蠕滑非线性和阻尼非线性等.采用ADAMS-Matlab联合仿真对车辆悬挂系统进行参数化改造,使弹簧刚度和阻尼系数均可调.采用基于遗传算法的多目标优化方法对悬挂参数进行优化,使车辆模型能同时满足3种动力学指标.对比优化前后模型的动力学性能可以发现:模型的运动稳定性和曲线通过性能得到显著提高,虽然运行平稳性有小幅降低,但仍能保持在优良的工作状态.  相似文献   

17.
The problem of modeling vehicle longitudinal motion is addressed for front wheel propelled vehicles. The chassis dynamics are modeled using relevant fundamental laws taking into account aerodynamic effects and road slop variation. The longitudinal slip, resulting from tire deformation, is captured through Kiencke's model. A highly nonlinear model is thus obtained and based upon in vehicle longitudinal motion simulation. A simpler, but nevertheless accurate, version of that model proves to be useful in vehicle longitudinal control. For security and comfort purpose, the vehicle speed must be tightly regulated, both in acceleration and deceleration modes, despite unpredictable changes in aerodynamics efforts and road slop. To this end, a nonlinear controller is developed using the Lyapunov design technique and formally shown to meet its objectives i.e. perfect chassis and wheel speed regulation.  相似文献   

18.
This paper addresses the co-design problem of decentralized dynamic event-triggered communication and active suspension control for an in-wheel motor driven electric vehicle equipped with a dynamic damper. The main objective is to simultaneously improve the desired suspension performance caused by various road disturbances and alleviate the network resource utilization for the concerned in-vehicle networked suspension system. First, a T-S fuzzy active suspension model of an electric vehicle under dynamic damping is established. Second,a novel decentralized dynamic event-triggered communication mechanism is developed to regulate each sensor's data transmissions such that sampled data packets on each sensor are scheduled in an independent manner. In contrast to the traditional static triggering mechanisms, a key feature of the proposed mechanism is that the threshold parameter in the event trigger is adjusted adaptively over time to reduce the network resources occupancy. Third, co-design criteria for the desired event-triggered fuzzy controller and dynamic triggering mechanisms are derived. Finally, comprehensive comparative simulation studies of a 3-degrees-of-freedom quarter suspension model are provided under both bump road disturbance and ISO-2631 classified random road disturbance to validate the effectiveness of the proposed co-design approach. It is shown that ride comfort can be greatly improved in either road disturbance case and the suspension deflection, dynamic tyre load and actuator control input are all kept below the prescribed maximum allowable limits, while simultaneously maintaining desirable communication efficiency.  相似文献   

19.
为了减少汽车轮胎动载荷对路面的损伤,研究兼顾行驶平顺性和道路友好性的悬架参数优化方法.建立了四自由度二分之一汽车振动模型,给出了整车振动方程、频响函数和路面输入模型,针对该汽车常用的行驶条件,以行驶平顺性指标和道路友好性指标的线性加权和作为优化目标,运用Matlab优化工具,对B级和C级路面典型工况的悬架刚度和阻尼进行仿真优化.优化结果表明,悬架参数对行驶平顺性和道路友好性有较大的影响;与原车相比,悬架参数优化后,行驶平顺性提高了5%~15%,道路友好性提高了2%~3%;针对B级和C级路面条件得到的两组优化结果为悬架参数没计提供了可行的目标范围.  相似文献   

20.
The core factors governing the performance of active vehicle suspension systems (AVSS) are the inherent trade-offs involving suspension travel, ride comfort, road holding and power consumption. In addition to this, robustness to parameter variations is an essential issue that affects the effectiveness of highly nonlinear electrohydraulic AVSS. Therefore, this paper proposes a nonlinear control approach using dynamic neural network (DNN)-based input–output feedback linearization (FBL) for a quarter-car AVSS. The gains of the proposed controllers and the weights of the DNNs are selected using particle swarm optimization (PSO) algorithm while addressing simultaneously the AVSS trade-offs. Robustness and effectiveness of the proposed controller were demonstrated through simulations.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号