纳米ZnO/Ag的制备及其光催化性能

以Zn(CH3COO)2·2H2O和AgNO3为原料,丙烯酰胺为单体,N,N′-亚甲基双丙烯酰胺为交联剂,用高分子凝胶法在较低的温度下制备出纳米ZnO/Ag.对纳米ZnO/Ag的结构和性能进行了表征,并研究了它的光催化活性.结果表明:在这个方法中,利用丙烯酰胺自由基聚合反应,同时利用网络剂有两个活化双健的双功能团效应,将高分子链联结起来构成网络.高分子凝胶形成的极小且均匀的网络限制了ZnO/Ag晶粒之间的团聚.制备出的纳米ZnO/Ag粉料颗粒为球形,未被Ag包覆的纳米ZnO的平均粒径约15 nm,被Ag包覆的纳米ZnO的平均粒径约45 nm.在次甲基蓝水溶液中加入3 g/LZnO/Ag粉料后,次甲基蓝的降解率为100%.沉积贵金属Ag使ZnO纳米粉料的光催化活性得到了很大提高,且可以重复使用.     

纳米复合材料TiO2/ZnFe2O4的制备及光催化性能

用高分子网络凝胶法制备TiO2/ZnFe2O4纳米复合材料,研究了掺杂ZnFe2O4对TiO2平均粒径、晶型及其光催化性能的影响.结果表明,掺杂的ZnFe2O4纳米晶高度分散、均匀地分布在TiO2表面,促进了TiO2向稳定的金红石相转变,并抑制了晶粒的长大.ZnFe2O4掺杂量为2%的TiO2/ZnFe2O4粉体在500℃煅烧后,在可见光范围内具有最佳的次甲基蓝降解效果,降解率达到100%.ZnFe2O4的掺杂扩展了TiO2的光谱响应范围.     

硫掺杂TiO2的制备及其光催化降解次甲基蓝研究

以TiCl4、(NH4)2SO4为原料,采用溶胶-凝胶法制备了硫掺杂纳米TiO2,利用XRD、TEM、FTIR等对样品进行了表征,并将其用于光催化降解次甲基蓝溶液.结果表明:制备的纳米TiO2为锐钛矿晶型,具有超强酸特征,平均粒径分布为10～30nm,S掺杂对TiO2的晶粒长大有抑制作用,经过硫掺杂的纳米TiO2光催化活性明显优于纯TiO2.     

溶胶-凝胶-冷冻法制备纳米TiO2及其表征

为解决纳米TiO2粉体易产生团聚的问题,采用溶胶-凝胶与冷冻干燥法制备纳米TiO2粉体.通过X射线衍射、扫描电子显微镜和紫外分光光度计对纳米TiO2粉体的物相组成、形貌和光催化活性进行了表征.实验结果表明:在400℃下所制得的TiO2纳米粉体的粒径约为6 nm,且粒度分布均匀,呈球形;所制得的TiO2纳米粉体在投加量为2 g/L时可使质量浓度为20 mg/L的甲基橙溶液在2.5 h内几乎全部降解.溶胶-凝胶与冷冻干燥法再结合阶段升温焙烧法可得到分散性好、粒径小和光催化活性好的粉体.     

化学复合镀Ni-P-TiO_2光催化降解次甲基蓝

以钛酸丁酯为原料通过溶胶 凝胶法制备出粒径 30nm左右的纳米TiO2 ,利用化学复合镀在钢铁基底上形成Ni P 纳米TiO2 复合镀层 ,该复合镀层对次甲基蓝有较好的光催化降解作用 ,其催化性能与粉末状纳米TiO2 的催化性能大致相当。     

Er-Ce共掺杂TiO2纳米粉体的制备及光催化性能研究

采用溶胶-凝胶法制备了Er-Ce共掺杂的TiO2纳米粉体，并以亚甲基蓝溶液为目标降解物研究了掺杂纳米TiO2粉体在紫外光作用下的光吸收和光催化性能。采用TG-DTA、XRD和TEM等测试技术对样品的晶型、形貌和粒径尺寸进行了表征。结果表明，Er-Ce共掺杂的TiO2粉体最佳热处理温度为550℃，结晶完整、主晶相为锐钛矿型，平均粒径约为20nm；掺杂可使TiO2吸收带发生红移，光催化性能增强；共掺杂体系的最佳量为n（Er）：n（TiO2）=0．1％，n（Ce）：n（TiO2）=0．05％。此掺杂量的TiO2粉体对亚甲基蓝有良好的降解效果，反应2h降解效果达到92．37％，优于同等条件下制备的未掺杂的纯TiO2粉体。掺杂复合光催化剂对亚甲基蓝的降解遵循一级动力学方程。     

TiO_2-硅藻土复合光催化剂的制备及其对有机染料的降解

为探索用于染料废水处理的新型矿物材料光催化染料复合剂的合成和效果,采用硅藻土表面包覆TiO2,制备TiO2-硅藻土纳米复合光催化剂,研究不同TiO2包覆量、煅烧温度、干燥温度、催化剂用量因素对复合光催化剂降解次甲基蓝效果的影响。结果表明:复合光催化剂的最佳合成条件为:煅烧温度500℃,干燥温度70℃,TiO2包覆量为25%,复合光催化剂处理次甲基蓝用量1g/L。所制备纳米级TiO2-硅藻土纳米复合光催化剂对次甲基蓝的脱色率可达90%。     

控制中和水解法制备纳米TiO2及其光催化性能的研究

用四氯化钛为原料,氨水为水解沉淀剂,采用控制中和水解的方法制备出了锐钛矿型纳米TiO2粉体.采用XRD和TEM手段对产品进行了表征分析,考察了中和水解过程中pH值、温度和浓度因素的影响.结果表明,pH值是影响产品前驱体组成的重要因素,当控制pH值在2～4的酸性条件下反应时,能得到团聚少的含有一定晶型的H2 TiO3前驱体,易于分离,收率可达97%以上,前驱体在600～800℃焙烧2h得到的是单一相锐钛矿TiO2纳米晶,平均粒径为15nm左右,高温焙烧时粒径生长缓慢,表现出很好的热稳定性.以甲基橙为目标降解物,测试了纳米TiO2样品的光催化性能.光催化降解反应60min时,甲基橙的去除率可达95.5%.     

Fe3+-TiO2薄膜经不同温度退火后的可见光催化性能

采用溶胶-凝胶法制备了掺杂Fe3+的TiO2薄膜,并在不同温度热处理.用SEM、XPS、UV-vis等分析方法进行结构表征和性能测试,通过降解亚甲基蓝溶液测试其可见光光催化活性.结果表明,723K时掺杂Fe3+的TiO2薄膜已经结晶,粒径为40～50nm.掺杂元素以Fe3+并口Fd2+形式存在于TiO2晶格并取代Ti4+形成Ti-O-Fe键,改变了TiO2的表面态,使TiO2带隙变窄,促进了对可见光的吸收.降解实验结果表明,823K热处理后掺杂铁的TiO2薄膜其光催化活性最好,在25W白炽灯模拟可见光下照射3.0h后,亚甲基蓝溶液的降解率接近30%.     

煅烧温度、煅烧时间和Fe3+掺杂量对TiO2光催化性能的影响

以钛酸四正了酯为先驱物,采用溶胶-凝胶法制备了纯TiO2和Fe3+掺杂的纳米TiO2(Fe3+/TiO2)光催化剂,并用XRD、UV-Vis等进行了表征,系统研究了煅烧温度、煅烧时间和Fe3+掺杂量对催化剂在自然光条件下光催化降解甲基橙性能的影响.结果表明,相同煅烧温度下,Fe3+/TiO2的粒径比纯TiO2的粒径小.制备纯TiO2和Fe3+/TiO2的最佳煅烧时间分别为4h和3h,最佳煅烧温度均为773K.适量掺入Fe3+可以显著提高纳米TiO2在自然光条件下的光催化降解活性,Fe3+/TiO2中Fe3+的最佳掺杂量为10.00%,相应的脱色效率为28.37%.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.