首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 46 毫秒
1.
新钢冷轧轧机为五机架联轧机组,每架轧机有3对不同的轧辊,分别为:支撑辊、中间辊和工作辊。六辊轧机的斜楔调整装置安装在轧机机架下部,换辊时,斜楔调整装置移出,使下工作辊、下中间辊及下支承辊移至下极限位置;换辊完成后,根据新辊的辊径,调节斜楔,以便在整个辊径变化范围内保证轧制线恒定。一旦轧制线不准确或者不稳定,则会导致轧机停机,严重时更会导致断带,给生产带来损失,给维护带来不便。  相似文献   

2.
凹版印刷机导向辊的挠曲变形分析及结构优化   总被引:1,自引:1,他引:0       下载免费PDF全文
马利娥  吴志勇  武吉梅  万清泉  李彦锋  李征 《包装工程》2014,35(13):100-104,127
目的导向辊是保证凹版印刷机印刷薄膜稳定传输最重要的部件,导向辊在薄膜张力及重力作用下容易发生挠曲变形。对导向辊进行挠曲变形分析和结构优化,在保证挠曲变形不影响薄膜套印精度的前提下,提高导向辊的随动性。方法根据导向辊自身结构特点,基于Ansys将导向辊简化为多体组合的连续简支梁模型,通过施加弹簧单元来仿真轴承对导向辊的作用,对不同壁厚的导向辊进行挠曲变形仿真分析,分析导向辊挠曲变形对印刷套印精度的影响。结果对导向辊建立了多体组合的有限元模型,得到了导向辊的挠曲变形曲线。当导向辊直径为?120mm,筒体长为1100mm,轴头长为110 mm,薄膜和导向辊的包角为90°时,工程实际使用的4.5 mm壁厚导向辊的最大挠曲变形值为51.208。结论导向辊最大挠曲变形发生在导向辊轴线方向的中间位置,其变形值随壁厚的增加而降低,壁厚对导向辊的挠曲变形影响较为明显,根据文中研究结果,对导向辊结构的壁厚进行优化后,导向辊的随动性得到了提高,从而可以提高薄膜传输质量。  相似文献   

3.
为准确计算辊套和辊芯热装等效应力,首次给出了考虑辊套和辊芯尺寸、材料物理性能参数及过盈量影响的辊套和辊芯热装径向应力计算公式,在此基础上得到了不同辊套厚度及过盈量条件下热装等效应力计算公式.为了验证该理论模型,用ANSYS软件对组合式支承辊热装过程进行了数值模拟,分析了不同辊套厚度、辊套和辊芯过盈量对结合面等效应力的影响.研究结果表明:相同过盈量及辊套厚度条件下,热装过程中周向应力约为径向应力的2倍;相同辊套厚度时,过盈量每增加0.1 mm,热装等效应力增大超过20 MPa;相同过盈量时,辊套厚度每增大100 mm,热装等效应力增大约20 MPa.  相似文献   

4.
一种双辊去渣破袋机,其中主动辊和被动辊的中心轴两端分别支撑在壳体的轴承上,主动辊和被动辊上的齿板呈螺旋状分布在主动辊和被动辊上;主动辊和被动辊的中心轴各自连接一电动机,主动辊的转动速度小于被动辊的转动速度;壳体的底部设有出料口,出料口的下方固定有网板;壳体的上部为进料口。本技术使用不同速度的辊筒,在齿板的拉扯力和三旋刀的剪切力作用下,轻松破袋去渣,其破袋去渣效果高达80%~90%,同时避免了物料筛选和粉碎的能源浪费。  相似文献   

5.
用影响函数法确定普通四辊轧机辊系的弹性变形,用有限单元法确定工作辊的热凸度,在此基础上耦合求解轧辊原始辊型曲线,与现场使用的辊型曲线对比表明:该法能较准确地快速确定轧辊的原始辊型.  相似文献   

6.
本文讨论的主要内容是热轧机如何进行板形控制,板形控制过程中,工作辊弯辊力、VC支撑辊和工作辊乳化液喷射对板形控制的影响。轧制过程中,工作辊表面热变形对板形的控制的影响。  相似文献   

7.
辊涂机漆耗小、生产效率高、操作简单、维护方便,常被用作带钢涂层生产线中。辊涂机的性能决定了材料表面的涂层厚度和涂层均匀度,对机组作业效率影响重大。随着科学技术的发展,辊涂机也有了新的发展。本文通过了解辊涂机的外观结构、工作原理、辊涂工艺,对新型辊涂机的主要改进方向进行了介绍,探讨未来辊涂机发展。  相似文献   

8.
王咏  王吼 《上海包装》1990,(3):37-38
瓦楞辊最重要的是它的齿和齿形,运转一些时间后,楞形磨损产生变化,影响产品质量。由于同时影响瓦楞辊磨损因素较多,现对其中一些因素作一浅析探讨。摩擦面的温度是决定磨损和摩擦过程基本因素之一。瓦楞辊原纸成型加工时需较高的温度(170℃以上),是其工艺特点,随着瓦楞辊表面温度上升,瓦楞辊材料的弹性模量降低,导致辊齿啮合刚度变化,辊材料是钢  相似文献   

9.
目的研究如何实现高效的无溶剂涂布,获得稳定的预定厚度涂层。方法在建立两辊间隙间涂布液流动数学模型的基础上,从涂布液辊间间隙分流分配关系和总结构内涂布液流量平衡两方面,分析无溶剂五辊顺转涂布系统涂布厚度的影响因素。结果转移钢辊和涂布钢辊的速比,计量辊和转移钢辊之间的间隙以及橡胶转移辊的压力等是对涂层厚度有直接影响的因子,毛细准数是涂层竖条道缺陷的主要影响因子,而涂布液的非牛顿特性会加重竖条道缺陷。结论设计无溶剂五辊顺转涂布系统时,需要综合考虑辊的直径、施加给橡胶辊载荷大小的范围、橡胶辊的硬度、适用涂布液的粘度范围和速度极限等因素。  相似文献   

10.
高低瓦楞辊齿形尺寸参数研究   总被引:1,自引:1,他引:0  
目的研究一种"高低瓦楞辊"组的齿形及具体尺寸,为制造高低瓦楞辊组提供设计参数,从而生产出高低瓦楞夹芯。方法在分析传统"等高瓦楞辊"齿形及有关标准尺寸参数基础上,预先确定基本尺寸参数值,并采用AutoCAD设计制图得出瓦楞辊齿形其他尺寸参数,然后模拟瓦楞辊滚压纸板过程,并测量纸板在瓦楞辊齿上的包角。按照纸板成形过程中张力的必要条件验算纸板成形的可行性,反复设计验算。结果得出了高低瓦楞辊齿形尺寸参数值。结论这种齿形尺寸参数的高低瓦楞辊能使纸板在瓦楞辊齿上的包角值为340°和332°,达到纸板成形过程张力要求,可作为高低瓦楞辊齿形尺寸参数。  相似文献   

11.
A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.  相似文献   

12.
An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.  相似文献   

13.
An analysis of anisotropy of the properties of a Bi2Se0.3Te2.7 solid solution was carried out using construction of demonstrative surfaces for thermoelectric effectiveness and thermal expansion coefficients. It is shown that the texture is an important factor forming anisotropy of properties and technological fitness of ingots for manufacturing modules. Anisotropy of properties based on the studies of the ingot textures obtained using the float-zone method and Bridgman method (growing thermoelectric plates in a flat cavity) was studied.  相似文献   

14.
A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.  相似文献   

15.
16.
Australia has several uranium mines and a large number of mineral sand mines, with associated processing facilities. Exposures resulting from these mining and processing operations usually involve intakes of mixtures of radionuclides. This work describes the development of a suite of first order, linear compartment models, based on the ICRP Publication 66 respiratory tract model, and an analytical solution to the decay equations, for assessing the consequences of such intakes. The computer programs based on these models directly compute excretion, organ retention and organ and whole-body doses for intakes of either single radionuclides or any mixture of radionuclides belonging to the same radioactive decay chain. The intake can be via inhalation, ingestion or injection, and can be acute, chronic or of limited duration. The starting concentration and degree of secular (dis)equilibrium can be specified for each radionuclide. No assumptions need to be made about the relative magnitudes of the radioactive half-lives of the different nuclides.  相似文献   

17.
18.
19.
可燃气体检测报警器测量结果的不确定度评定   总被引:1,自引:0,他引:1  
本文详细介绍了可燃气体检测报警器示值误差测量结果的不确定度评定方法。  相似文献   

20.
水三相点是开尔文热力学温度的唯一基准点,也是ITS-90国际温标重要的定义固定点。因此,水三相点不确定度分析对整个温标的建立、温度量值传递起着至关重要的作用。近3年来,中国计量科学研究院研制出一系列高质量的水三相点容器,加强了水三相点的研究,为不确定度的分析提供了更为可靠的实验依据。同时,不确定度的分析也是客观评价新研制容器性能的一个重要指标。因此,根据实验结果对新研制容器所复现的水三相点进行了不确定度评定。评定结果表明,其扩展不确定度为0.16mK(k=2.69,P=0.99)。  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号