热声斯特林发动机系统的起消振过程研究

在自行研制的1台行波型热声斯特林发动机上考察其起振和消振行为.针对不同的加热功率和充气压力下,系统地研究了起消振过程中的温度、压力变化特性,着重分析了滞后回路形成的过程和影响热声系统滞后回路的因素,指出滞后回路存在的条件,对深入理解热声系统的起消振行为具有参考意义.     

热声斯特林发动机系统起消振过程研究

在自行研制的1台行波型热声斯特林发动机上考察其起振和消振行为。针对不同的加热功率和充气压力，系统地研究了起消振过程中的温度、压力变化特性，着重分析了滞后回路形成的过程和影响热声系统滞后回路的因素，指出滞后回路存在的条件，对深入理解热声系统的起消振行为具有参考意义。     

驻波热声发动机板叠温度分布的红外观察

为了深入研究热声板叠中的能量流动和分布,采用红外热像仪对自行设计搭建的驻波热声发动机板叠进行了温度场观测,重点分析了起消振过程中板叠的轴向和径向温度分布变化.实验结果表明:在起振时,板叠轴向中部的无量纲温度会出现突然升高并随之保持平稳.通过分析不同板叠安装角度下的板叠温度分布,首次发现自然对流会使起振前板叠的径向温度分...     

大型多功能热声发动机的研制及初步实验 第二部分:热声发动机的初步实验

行波热声发动机在回热器中进行的是可逆热声转换过程,理论上可以更高效地产生和传输声功,因而具有广阔的研究应用前景.对自行研制的大型多功能热声发动机进行了初步实验,着重研究了系统的起振、消振过程及压力波动情况.实验结果表明,该热声发动机比纯驻波型热声发动机具有更低的起振温度、更大的压比及更高的热声转换效率.以氮气为工质,在充气压力为9×105 Pa的条件下,该热声发动机最大压比达1.21,工作频率为25 Hz,这是当前国际上处于前列的实验结果.     

热声起振过程的实验研究

起振过程是热声现象的重要部分之一.在自行研制的混合型热声发动机系统中对起振过程进行了实验研究,通过分析起振过程的压力、频谱变化,总结出起振过程中储能、起振、饱和3个阶段的特性,并分析了亥姆霍兹共鸣器对起振阶段的影响,通过与国外相似实验结果进行对比,指出了之间的共同点以及差异,为开展热声起振机理研究提供了参考.     

初始加热条件对起振温度影响的实验研究

为得到对热声发动机的实际起振条件,针对一台高频行波热声发动机开展了初始加热量对起振温度影响的研究。搭建了实验台并成功观测到临界初始加热功率50 W,采用不同初始加热功率得到临界起振温度并与理论值进行对比发现只要靠近高温端的温度梯度大于临界温度梯度,系统就可起振。     

热声系统起振消振行为的实验研究

对热声系统的起振与消振行为进行了实验研究,发现在的热声振荡滞后回路。研究了不同加热方式（对称加热与单向加热）及充气压力时滞后回路的影响,得出一些令人感兴趣的结论。     

丝网板叠型驻波热声发动机的工作特性研究

基于线性热声理论设计并搭建了一台丝网型驻波热声发动机,采用不同目数的不锈钢丝网进行试验,考察了丝网板叠几何参数和工作压力对热声发动机工作特性的影响,实验结果和线性热声理论计算结果吻合度较好。实验发现,高目数丝网板叠更容易使系统起振,在实验范围内热声发动机采用不同板叠时的最小起振温度均发生在小充气压力下;在不同的充气压力下,存在最优目数的丝网使得发动机性能最佳。对该台热声发动机而言,最佳的丝网水利半径应为热渗透深度的4.5倍左右。     

行波热声发动机末端耦合方式研究

行波热声发动机可与各种声学负载耦合,在对耦合位置的研究基础上,进一步开展负载末端耦合时行波热声发动机的性能研究.同时改变直管谐振管内径和长度,使频率恒为67.7 Hz,保证发动机环路声功转换特性一致.研究表明,当谐振管内径为120 mm时,系统性能最好;以氦气为工质,在平均压力3 MPa、加热功率2 000 W、热端温...     

平板型mLHP实验研究

研制了一套以铜为壳体、不锈钢丝网为毛细芯、丙酮为工质的小型平板型环路热管,实验研究了其系统倾角为10°、50°、90°,工质充灌量为50%、60%和70%条件下的运行特性.实验显示铜一不锈钢一丙酮平板型mLHP具有良好的启动和变工况特性.mLHP系统在热负荷低于18W和高于42W时均能达到稳定运行,而在热负荷介于18～42W的某些工况,系统出现温度波动现象,且其温度波动的波幅和周期与系统倾角、充灌量及热负荷有着密切的关系.系统在变工况运行时具有很快的响应速度,一般在2～3min内达到新平衡状态.此外,在不同工况下系统热阻介于0.45～2.8℃/W之间.     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.