Nd、Y对AZ31镁合金热轧退火薄板耐蚀性的影响

为提高AZ31镁合金热轧退火薄板的耐蚀性,本实验在合金中分别添加单一Nd和复合Nd+Y稀土元素,采用盐雾腐蚀和电化学腐蚀实验方法对其耐蚀性展开研究,并利用扫描电镜(SEM)、X射线衍射(XRD)仪对合金和腐蚀产物的微观组织及结构进行观察分析。结果表明:添加稀土元素Nd、Y后,AZ31镁合金表面可形成更为耐蚀的含有稀土氧化物Nd_2O_3的腐蚀产物膜,提高对基体的保护作用;添加Nd、Y元素的AZ31镁合金中新的耐蚀相Al_2Nd和Al_2Y析出,有害相β-Mg_(17)Al_(12)减少,使合金自腐蚀电位正移,腐蚀电流密度减小,腐蚀速率减缓,耐蚀性明显提高;复合添加Nd+Y比单一添加Nd更有利于提高AZ31镁合金的耐蚀性,且添加量为0.5%Nd+0.5%Y时合金的耐蚀性能提高最为显著。     

Nd对AZ91镁合金显微组织和耐腐蚀性能的影响

用金相显微镜、扫描电镜和静态质量损失法对AZ91-xNd镁合金(x=1.1%,1.4%,1.9%)的微观组织和腐蚀性能进行表征,研究了Nd对AZ9l镁合金显微组织和耐腐蚀性能的影响.结果表明:稀土Nd的添加明显细化了合金的组织,使半连续网状β(Mgl7Al12)相变为细小的长条状,且分布更加均匀.在合金中还生成了颗粒状...     

稀土Ce和Nd对AZ31镁合金耐蚀性能的影响

采用盐雾腐蚀和动电位扫描研究了稀土元素Ce、Nd对AZ31镁合金耐腐蚀性能的影响.采用数码相机、金相显微镜和扫描电镜观察及定量金相分析系统测量分析了样品的腐蚀程度,并采用恒电位仪测量了动电位扫描极化曲线.结果表明,盐雾腐蚀试验中,合金试样腐蚀面积百分数随时间延长呈直线上升,添加稀土Ce和Nd后腐蚀速率降低50%以上.在电化学试验中.添加稀土后合金腐蚀电流密度降低了1/3～1/2.稀土可以起到提高α(Mg)固溶体耐蚀性能的作用,还可以形成含稀土的第二相并使AZ31合金中的β(Mg17Al12)相均匀分布,发挥其阻碍腐蚀的作用,从而最终提高AZ31镁合金的耐蚀性能.     

稀土对AZ91镁合金干/湿循环腐蚀产物及阻抗行为的影响

采用扫描电镜(SEM)、X射线衍射(XRD)、能谱分析(EDS)研究添加(La,Ce)混合稀土前后AZ91镁合金在融雪剂溶液中经历干/湿交替循环腐蚀后腐蚀产物的组成和结构。结果表明:未添加(La,Ce)混合稀土的AZ91镁合金的腐蚀产物主要由Mg(OH)_2,MgO,CaCO_3及Mg_6Al_2CO_3(OH)_(16)·4H_2O组成;而添加混合稀土的AZ91镁合金表面生成了(La,Ce)AlO_3等含稀土元素的腐蚀产物,同时腐蚀产物出现致密层。不同周期干/湿交替循环腐蚀的电化学阻抗谱(EIS)测试结果表明,添加(La,Ce)混合稀土的镁合金在相同腐蚀周期的阻抗谱幅值均高于AZ91镁合金的阻抗谱幅值,稀土的添加有助于降低阻抗谱的弥散效应,表明(La,Ce)混合稀土可以提高AZ91镁合金在干/湿交替腐蚀环境中的耐蚀性和腐蚀产物膜的稳定性。     

添加稀土Gd对Mg-6Al镁合金组织和耐蚀性的影响

Mg-6Al镁合金具有较好的铸造性能和力学性能,目前鲜见单一稀土元素对其腐蚀性能影响的报道。通过合金制备、微观组织分析和耐蚀性测试等方法研究了稀土Gd添加量对Mg-6Al镁合金微观组织和耐蚀性能的影响。OM、SEM、EDS、XRD分析结果表明,稀土Gd的添加改善并细化了Mg-6Al合金的铸态组织,形成杆状或块状的Al2Gd新相;动电位极化、浸泡试验等测试结果表明Gd的添加显著提高了Mg-6Al合金在3.5%NaCl溶液中的耐腐蚀性能,Mg-6Al-2%Gd镁合金的腐蚀速度最小,为0.83 mm/a,且腐蚀后组织较为致密,腐蚀产物和腐蚀坑均变小,Mg-6Al-x Gd合金的腐蚀产物主要为Mg(OH)2。     

AZ91铸态镁合金中Mn含量对其微观组织及耐蚀性能的影响

目前,关于Mn对AZ91铸态镁合金耐蚀性能影响的研究并不充分,尤其是腐蚀机制方面仍不清楚。采用静态失重、电化学及盐雾腐蚀法研究了Mn含量对AZ91铸态镁合金微观组织及耐腐蚀性能的影响。利用金相显微镜(OM)、扫描电镜(SEM)观察AZ91铸态镁合金的微观组织和腐蚀形貌,采用能谱(EDS)仪、X射线衍射仪(XRD)分析了其物相组成。结果表明:AZ91铸态镁合金中的Mn主要以颗粒状的低电化学活性物质Al2Mn形式存在,阻碍了其腐蚀过程的进行;Mn能使AZ91铸态镁合金中的有效腐蚀相β-Mg17Al12减少,分布更弥散,从而使合金的腐蚀电位升高,腐蚀电流降低,腐蚀速率降低,耐腐蚀性能增强;含0.8%Mn的铸态镁合金的耐腐蚀性能最好。     

固溶处理对AM60B+XRE及AZ91D+XRE 镁合金性能的影响

研究了添加少量富铈混合稀土的AM60B+xRE及AZ91D+xRE合金(x=0.4、0.8、1.2、1.6和2.0%,质量分数)固溶处理后的显微组织与机械性能.结果表明,添加混合稀土能显著提高合金的抗拉强度σb和屈服强度σ0.2,固溶处理明显提高AZ91D+xRE合金的强度;AM60B+xRE及AZ91D+xRE合金的铸态组织由α(Mg)固溶体、杆状Al11RE3相、颗粒状Al10Ce2Mn7相以及网状Mg17Al12相组成,经过固溶处理后,网状Mg17Al12相完全溶解,只剩下热稳定性较高的Al11RE3相和Al10Ce2Mn7相,随固溶时间的延长,其形态略有改变.AM60B+xRE合金拉伸试样断口呈带局部韧窝的准解理断裂形式,而AZ91D+xRE合金则呈现沿晶断裂+解理断裂的混合断口形态.     

混合稀土对AZ91镁合金在NaCl溶液中的腐蚀行为影响

通过静态失重法、极化曲线和交流阻抗测试研究了混合稀土 (Re)对AZ91镁合金腐蚀行为的影响。结果表明 :Re的加入使AZ91微观组织得到改善 ,减缓了AZ91镁合金在NaCl溶液中的腐蚀     

稀土Y和Sm对AZ91D镁合金组织与性能的影响

采用控制变量法研究单一稀土Y和复合稀土Y,Sm元素对AZ91D镁合金微观组织与力学性能的影响,分析稀土元素对AZ91D合金的细化机理。结果表明：复合添加稀土Y和Sm对AZ91D合金的作用效果明显好于单一添加稀土Y对AZ91D合金的作用效果,添加Y和Sm后,生成了块状相Al₂Y相和针状相Al₂Sm相,可以作为α-Mg的有效异质形核点。当加入量为0.8%（质量分数,下同）Y+1.0% Sm时,α-Mg晶粒尺寸最为细小,分布最为均匀,其合金的硬度、抗拉强度及伸长率分别为67.42HV,153.37 MPa和3.62%,改善了铸态AZ91D合金的室温力学性能,但是超过这个最佳添加量后,合金的室温力学性能开始下降。     

Nd对AZ91镁合金组织和高温力学性能的影响

研究了Nd对AZ91镁合金组织和高温力学性能的影响.结果表明,稀土Nd(1%～4%(wt))的加入明显细化了AZ91镁合金的铸态组织,减少了β(Mg17Al12)相的析出.随着稀土Nd含量的增加,室温、150℃和250℃等3个温度下的强度都是先升后降,Nd含量为1%时合金的强度均达到最大值,特别是150℃下其强度高达203MPa;Nd含量的增加对AZ91镁合金的延伸率影响规律也是先升后降,高温下当Nd含量为2%时合金的延伸率达到最大值,表现出良好的韧性,同时也具有较高强度.     

Estimation of Parameters of Universal Distribution of Moments of Failure of Products

A method is proposed for estimating the parameters of a mixture of exponential and Weibull distributions for which the accuracy of preliminary estimates obtained by graphical analysis is refined in accordance with the criterion of maximum likelihood. The efficiency of the proposed method is supported by the results of statistical modeling.     

Analysis of the rate of propagation of the wave of change of boiling modes

An approximate analytical expression is derived for the velocity of the front of the wave of change of boiling modes on a rod and on a plate. The impact of the Thomson effect and of the heater orientation in the gravity field is included. Adequate agreement is demonstrated between the derived relations and experimental data.     

Evaluation of optical properties of highly scattering media by moments of distributions of times of flight of photons

A novel method for the determination of the optical properties of tissue from time-domain measurements is presented. The data analysis is based on the evaluation of the first moment and the second centralized moment, i.e., the mean time of flight and the variance of the measured distribution of times of flight (DTOF) of photons injected by short (picosecond) laser pulses. Analytical expressions are derived for calculation of absorption and of reduced scattering coefficients from these moments by application of diffusion theory for infinite and semi-infinite homogeneous media. The proposed method was tested on experimental data obtained with phantoms, and results for absorption and reduced scattering coefficients obtained by the proposed method are compared with those obtained by fitting of the same data with analytical solutions of the diffusion equation. Furthermore, the accuracy of the moment analysis was investigated for a range of integration limits of the DTOF. The moment analysis may serve as a comparatively fast method for evaluating optical properties with sufficient accuracy and can be used, e.g., for on-line monitoring of optical properties of biological tissue.     

Analysis of anisotropy of properties on the basis of studies of texture of coarse-grained ingots of thermoelectric materials

An analysis of anisotropy of the properties of a Bi₂Se_0.3Te_2.7 solid solution was carried out using construction of demonstrative surfaces for thermoelectric effectiveness and thermal expansion coefficients. It is shown that the texture is an important factor forming anisotropy of properties and technological fitness of ingots for manufacturing modules. Anisotropy of properties based on the studies of the ingot textures obtained using the float-zone method and Bridgman method (growing thermoelectric plates in a flat cavity) was studied.     

卧式金属罐容量的测量结果不确定度

本文根据多年的实践检定经验 ,参照JJF1 0 59- 1 999《测量不确定度评定与表示》以及《测量不确定度表达 1 0讲》 ,对卧式金属罐容量的测量结果不确定度进行了评定。     

盐酸浓度不确定度的评估

通过对盐酸浓度标定的过程分析，找出影响结果的各个分量，进行不确定度的评定，按照计量技术规范给出标准的表示法。     

Estimation of potentialities of methods of summation of direct measurement errors

Conventional methods for summation of direct measurement errors are considered. Conditions under which these methods provide consistent results are stated. It is proposed to utilize for characteristic of the total error, its interval estimator or the half-sum of the value obtained by adding up its arithmetic and geometric random errors.Translated from Izmeritel'naya Tekhnika, No. 4, pp. 10–12, April, 1995.