碳纳米管增强开孔铝基复合泡沫的疲劳性能

采用原位化学气相沉积、短时球磨和填加造孔剂法相结合的工艺制备了碳纳米管(CNTs)/Al复合泡沫,研究了其在压缩-压缩循环载荷下的力学性能及失效机制。结果表明,CNTs/Al复合泡沫的应变-循环次数曲线经历线弹性、应变硬化及应变快速增长三个阶段。不同于泡沫铝的逐层坍塌变形失效模式,CNTs/Al复合泡沫疲劳失效的主要原因是大量剪切变形带的形成,试样出现快速的塑性变形。此外,CNTs含量为2.5wt%、孔隙率为60%的复合泡沫试样的疲劳强度相比于泡沫铝提高了92%。CNTs的均匀分布及增强相与基体材料之间良好的界面结合性保证了疲劳载荷能够以剪切力的形式从基体传递到CNTs上,使其充分发挥自身高强度、高韧性的特点,进而提高了疲劳性能。      

Mechanical property enhancement of aligned multi-walled carbon nanotube sheets and composites through press-drawing process

A solid-state drawing and winding process was done to create thin aligned carbon nanotube (CNT) sheets from CNT arrays. However, waviness and poor packing of CNTs in the sheets are two main weaknesses restricting their reinforcing efficiency in composites. This report proposes a simple press-drawing technique to reduce wavy CNTs and to enhance dense packing of CNTs in the sheets. Non-pressed and pressed CNT/epoxy composites were developed using prepreg processing with a vacuum-assisted system. Effects of pressing on the mechanical properties of the aligned CNT sheets and CNT/epoxy composites were examined. Pressing with distributed loads of 147, 221, and 294 N/m showed a substantial increase in the tensile strength and the elastic modulus of the aligned CNT sheets and their composites. The CNT sheets under a press load of 221 N/m exhibited the best mechanical properties found in this study. With a press load of 221 N/m, the pressed CNT sheet and its composite, respectively, enhanced the tensile strength by 139.1 and 141.9%, and the elastic modulus by 489 and 77.6% when compared with non-pressed ones. The pressed CNT/epoxy composites achieved high tensile strength (526.2 MPa) and elastic modulus (100.2 GPa). Results show that press-drawing is an important step to produce superior CNT sheets for development of high-performance CNT composites.     

Solution-processed Ni–CNTs filled ferroelectric P(VDF–TrFE) composites with improved dielectric properties and thermal conductivity

Dielectric composites made using two kinds of poly(vinylidene fluoride–trifluoroethylene) [P(VDF–TrFE)] (70/30 and 80/20 mol%) as polymer matrices and nickel particles coated carbon nanotubes (Ni–CNTs) as filler were developed via solution-processed method. The scanning electron microscopy (SEM) indicated good compatibility and dispersion of Ni–CNTs in the P(VDF–TrFE) matrix. Ni–CNTs/P(VDF–TrFE) composites exhibited high dielectric constants with low dielectric losses. The maximum dielectric constants of Ni–CNTs/P(VDF–TrFE) composites of 198 and 185 at 100 Hz were obtained at 18.0 wt% Ni–CNTs loading, respectively. The incorporation of Ni–CNTs in the P(VDF–TrFE) matrix resulted in enhanced thermal conductivity. The highest values, obtained at 18.0 wt% Ni–CNTs loading, were 1.05 and 1.03 W/m K, respectively. Although there were no very obvious difference, the dielectric properties and thermal conductivity of Ni–CNTs/P(VDF–TrFE) 70/30 mol% composites were slightly better to those of Ni–CNTs/P(VDF–TrFE) 80/20 mol% composites in many cases. The aforementioned results suggest that these high-performance composites hold great promise for application in electrical and electronic field.     

超高分子量聚乙烯(UHMWPE)纤维表面处理对UHMWPE/环氧树脂复合材料界面性能的影响机制

从工程化应用角度研究了常压空气等离子体改性对超高分子量聚乙烯（UHMWPE）纤维/环氧树脂复合材料界面性能的调节机制,主要分析了不同处理时间对UHMWPE纤维表面状态变化的影响,及其对UHMWPE/环氧树脂复合材料界面黏结性能的影响规律。采用SEM及纤维吸水测试研究了等离子体处理对UHMWPE纤维表面物理形貌及纤维表面浸润性能的影响,分别以拉伸和弯曲的方式,通过纤维表面脱黏力及层合板层间剪切强度对UHMWPE/环氧树脂复合材料的界面黏结性能进行表征。结果表明,仅经过4 s的空气等离子体处理之后,UHMWPE纤维表面脱黏力的提高幅度为84.0%,UHMWPE/环氧树脂复合材料层合板的层间剪切强度由未处理的7.01 MPa提高至15.81 MPa,增幅高达125.5%。研究发现,通过常压空气等离子体处理改变了UHMWPE纤维的表面状态,可以显著高效地调节UHMWPE/环氧树脂复合材料的界面性能,为扩大该材料的后续工程化应用提供了理论基础。      

Effects of particle size and properties on the microstructures,mechanical properties,and fracture mechanisms of 7075Al hybrid composites prepared by squeeze casting

To investigate the effects of particle size and properties on the mechanical properties of 7075Al matrix composites, hybrid composites reinforced using three different reinforcement combinations, 40 vol. % 7 μm SiC_p with 5 vol. % 7 μm SiC_p, 35 μm SiC_p, and 35 μm Ti, were prepared using squeeze casting. The failure mechanisms and the microstructure–property relationships of hybrid composites were studied using SEM, TEM, and tensile tests. The composite containing Ti particles achieved the highest tensile strength of 626 MPa and an elongation of 1.2 %. Fracture mechanism analyses imply that the reduced strength for the 35 μm SiC_p-containing composite are caused by the inefficient load transfer capability resulting from the preferential breakage of larger-sized SiC_p particles during the deformation process. In contrast, micro-zones formed by Ti particles at the center and matrix alloy with few dislocations around release stress and deform synergistically during deformation, which decreases the breakage of SiC_p and improves the plastic deformation ability of the matrix alloy, resulting in a good combination of strength and ductility.     

Rate-Dependent Elasto-Viscoplastic Constitutive Model for Industrial Powders. Part 1: Parameter Quantification

ABSTRACT

The rate-dependent mechanical behavior of a dry industrial powder (MZF powder) was studied using a cubical triaxial tester (CTT) within the context of a new elasto-viscoplastic model (PSU-EVP model). The compression and shear properties of the powder were quantified at compression rates of 0.62, 6.21, and 20.7 MPa/minute with pressures up to 11 MPa. Test results demonstrated that the compression and shear responses of the powder were nonlinear, consistent, and reproducible (coefficient of variation or COV ≤ 15%). Also, MZF powder exhibited varying elastic and plastic deformation at different pressure levels that were quantified using statistical correlations (R² > 0.90). For example, the average bulk modulus and shear modulus values for MZF powder increased linearly with pressure (R² > 0.90) at all compression rates. The failure stress values also increased with the increase in mean pressure. For instance, at a compression rate of 0.62 MPa/minute, failure stress increased from 5.0 to 13.3 MPa as the confining pressure increased from 2.2 to 8.5 MPa. Similar effects were noted at compression rates of 6.21 and 20.7 MPa/minute. Overall, failure stress decreased with increasing compression rate. From the data collected, it was demonstrated that compression rate does have substantial effect on the compressibility and shear behavior of powders that can be quantified using the CTT and is suitable for use in the PSU-EVP model.     

Comparison of the modified three-rail shear test and the [(+45°,−45°)]ns tensile test for pure shear fatigue loading of carbon fabric thermoplastics

The (three)-rail shear test is rarely considered for testing of fibre-reinforced composites under pure shear fatigue loading conditions because of all experimental difficulties. However, in this article, a carbon fabric-reinforced PPS is tested using a modified three-rail shear test setup. The results are compared with [(+45°,−45°)]_4s tensile tests with good correspondence. All fatigue experiments were done with R = 0 and the influence of maximum shear stress and frequency is investigated. It can be concluded that an increase in maximum shear stress decreases fatigue lifetime, whereas an increase in frequency increases the lifetime. Before failure, a sudden increase in both temperature and permanent deformation could be detected. Creep tests yielded that the occurring deformation is mainly due to the fatigue loading, rather than due to creep phenomena.     

机械混炼对碳纳米管/丁苯橡胶复合材料的影响

为研究机械混炼对碳纳米管(CNTs)/粉末丁苯橡胶(SBR)复合材料性能的影响,从而获得性能优异的CNTs/SBR复合材料,联合采用喷雾干燥法和机械混炼法,制备高填充量CNTs/SBR复合材料.将喷雾干燥法制备的CNTs/粉末SBR复合材料在开炼机上机械混炼,对比分析混炼前后试样的物理和力学等相关性能,并对其微观形貌进行检测.结果表明,机械混炼使CNTs获得进一步的分散,与SBR基体间作用力得到增强,与混炼前相比,混炼后试样的玻璃化转变温度、交联度和常规力学性能均得到提高,当CNTs加入量为50phr时,混炼后复合材料的拉伸强度和撕裂强度分别为13.1MPa和39.8kN/m,比混炼前试样分别提高了约80%和20%.     

Microstructure and mechanical behaviour of aluminium matrix composites reinforced with graphene oxide and carbon nanotubes

Aluminium (Al) matrix composites reinforced with either 0.5 wt% graphene oxide (GO) or 0.5 wt% carbon nanotubes (CNTs) were hot extruded from ball-milled powders. A control, pure Al bar was also fabricated. Microstructural examination, including Raman mapping, showed a relatively poor dispersion of the carbon nanomaterials within the Al matrix, particularly in the case of the CNTs. Consequently, while the mean grain size of the Al matrix remains invariant with the addition of CNTs, the Al/GO composite exhibits reduced grain size compared to pure Al due to the pinning effect of the reinforcement. Moreover, the addition of both carbonaceous materials resulted in a slight decrease in the typical extrusion duplex <111> + <100> fibre texture intensity. This weakening of the texture was more pronounced in the Al/GO composite, partly due to the pinning effect of the reinforcement. In agreement with their relative mean grain sizes, the Al/GO composite shows an improved mechanical performance over pure Al. Despite the similarity of the mean grain sizes, the Al/CNT composite displays comparable hardness and a decreased compressive yield stress relative to the pure Al. In the absence of chemical reactions at the interfaces, this was attributed to a low efficiency of load transfer from the Al matrix to the reinforcement resulting from the large extent of agglomeration of CNTs.     

石墨表面镀Si对石墨/Al复合材料热物理性能的影响

研究了石墨粒径及表面镀Si处理对石墨/Al复合材料热物理性能的影响。结果表明:在盐浴过程中石墨表面形成了SiC层,这不仅增强了石墨-Si/Al复合材料的界面结合力,而且抑制了Al4C3相的产生。随着石墨鳞片体积分数从50%增加到70%,复合材料X-Y方向的热导率从492 W/(m·K)增加到654 W/(m·K),而且体积分数为50%的镀Si石墨/Al复合材料抗弯强度达到了81 MPa,相比未镀覆的提高了53%,是理想的定向导热电子封装材料。随着石墨粒径从500μm减小到150μm,石墨-Si/Al复合材料X-Y面方向的热导率由654 W/(m·K)降低到445 W/(m·K),但Z方向的热导率和复合材料抗弯强度变化不明显。     

Electrical properties of graphene nanoplatelets/ultra-high molecular weight polyethylene composites

Graphene nanoplatelets (GNPs)/ultra-high molecular weight polyethylene (UHMWPE) composites with a segregated structure had been fabricated using ethanol-assisted dispersion and hot compression at 180 °C. A percolation threshold of 3.5 wt% was achieved because of the formation conductive network. The positive temperature coefficient (PTC) and the negative temperature coefficient (NTC) effects of GNPs/UHMWPE composites had been investigated. The PTC behavior enhanced with increasing GNPs content but this was not always the case. The maximum PTC effect was observed in GNPs/UHMWPE composites (GNPs, 3.8 wt%) with the relatively low room temperature resistivity and the relatively high peak resistivity. The structure for GNPs/UHMWPE composites was examined by the SEM. The fact revealed that the slight interaction between GNPs and UHMWPE matrix may be changed by thermal cycles, and this can explain why thermal cycles could increase PTC and NTC intensity.     

Densification behavior and mechanical properties of spark plasma-sintered ZrC–TiC and ZrC–TiC–CNT composites

Titanium carbide (TiC) and carbon nanotubes (CNTs) were introduced into zirconium carbide (ZrC) ceramics to improve the fracture toughness. ZrC–TiC and ZrC–TiC–CNT composites containing 0–30 vol.% TiC and 0.25–1 mass% CNT were prepared by spark plasma sintering at temperatures of 1750–1850 °C for 300 s under a pressure of 40 MPa. Densification behavior, microstructure, and mechanical properties of the ZrC-based composites were investigated. Fully dense ZrC–TiC and ZrC–TiC–CNT composites with a relative density of more than 98 % were obtained. Vickers hardness of ZrC-based composites increased with increasing TiC content and the highest hardness was achieved with the addition of 20 vol.% TiC. Addition of CNTs up to 0.5 wt% significantly increased the fracture toughness of ZrC-based composites, whereas the addition of TiC did not have this effect.     

Comparative study of wear performance of particulate and fiber-reinforced nano-ZnO/ultra-high molecular weight polyethylene hybrid composites using response surface methodology

The effects of two types of filler reinforcements i.e. particulate (talc particles) and fiber (Glass Fiber (GF)) as secondary reinforcements in ultra-high molecular weight polyethylene (UHMWPE)-based composites on the wear and friction properties were discussed in this paper. These UHMWPE hybrid composites were fabricated by the addition of 10 wt% of talc and glass fiber at a fixed nano-ZnO loading of 10 wt% using a hot compression moulding technique. The wear and friction properties of these hybrid composites were investigated using a pin-on-disc tester with different operating conditions of applied loads, sliding speeds and sliding distances based on response surface Box–Behnken design. Response Surface Methodology (RSM) was applied to model the effects of various variables of applied load, sliding speed and distance on the wear volume loss and average coefficient of friction (COF) of UHMWPE hybrid composites. The mathematical regression models of the wear volume and average COF were derived from the analysis of variance (ANOVA). Optimization of the independent variables to minimize the wear and friction responses of both UHMWPE composites was estimated using RSM. The mathematical models showed that applied load, sliding speed and distance have significant effects on the wear and friction properties of both UHMWPE composites in the tested range of variables. The most significant, in order of the variables that affect the volume loss and friction of UHMWPE composites is load, followed by sliding distance and speed. In addition, the combined effects of load and distance indicate the highest significance on volume loss and average COF for both UHMWPE hybrid composites as compared to other variable interactions. GF/ZnO/UHMWPE exhibited better wear performance compared to talc/ZnO/UHMWPE hybrid composites. The severity of worn surfaces of the GF/ZnO/UHMWPE was less than that of talc/ZnO/UHMWPE. The GF/ZnO/UHMWPE produced transfer films that were more uniform and had better coverage compared to talc/ZnO/UHMWPE.     

Effect of grain size on cyclic microplasticity of ECAP processed commercial pure magnesium

Equal channel angular pressing (ECAP) was performed on the extruded commercial pure magnesium at 250 °C for 4 passes. Heat treatments were carried out to modify the microstructures. The cyclic plastic deformation behavior of pure Mg with different grain sizes in microstrain region was studied by tensile loading and unloading experiments. The microplastic deformation process of pure Mg can be divided into two stages. In the first stage, pronounced plastic deformation associated with dislocation motion on basal plane is initiated at several MPa. The materials are softened and characterized by low friction stresses and hardening exponents. The microplastic deformation enters into region II above the strain of about 8 × 10^?4. Annihilation and tangle of dislocations lead to the increase of hardening exponents and friction stresses. Pure Mg shows a very pronounced anelastic behavior during cyclic microplastic deformation, which results in a rapid increase of modulus defect, effectively decreasing the elastic modulus by up to 60 %. Grain size has a marked effect on microplastic deformation behavior of pure Mg. With increasing the grain size, the specimen shows a more pronounced microstrain and anelastic behavior.     

Low-velocity penetration damage of Kevlar woven fabrics impregnated with shear thickening fluid penetrated with different tups

Abstract

Low-velocity penetration damage behaviors of Kevlar woven fabrics impregnated with shear thickening fluid (STF) were investigated. Cone-shaped tup (CST) and hemispheric tup (HST) were employed to penetrate fabric/STF composites with the velocities of 1.5 m/s and 3.0 m/s under drop-weight tests. The fabric impregnated with 3:1 diluted volume ratio has the highest energy absorption and the lowest deformation. The peak load and energy absorption under HST penetration at 3.0 m/s are 2.0?kN and 36.7 J, which are higher than the CST penetration. Energy absorption increment under HST penetration at 3.0 m/s is 61.76% while 117.88% for CST penetration.     

Effect of hydrothermal pretreatment on the properties of moso bamboo particles reinforced polyvinyl chloride composites

Bamboo plastic composites were fabricated from polyvinyl chloride (PVC) and moso bamboo particles (BP). In order to improve the interfacial interaction between BP and PVC, as well as to obtain composites with outstanding mechanical properties, the roles of hydrothermal treating temperatures (120, 140, 160, 180, 200, 220, 240, 260 and 280 °C) on characteristics of BP and properties of the PVC/BP composites were investigated. Results showed that hydrothermal modification improved the surface property of BP and wiped off hemicelluloses and pectin. A uniform dispersion of BP in PVC matrix was observed by SEM with hydrothermal treatment. Tensile strength, tensile modulus and flexural strength of the composites achieved their maximal values of 15.79 MPa, 6702.26 MPa and 39.57 MPa, respectively, with 180 °C hydrothermal treatment. The highest values of elongation at break and flexural deformation were 3.75 ± 0.20% with 200 °C hydrothermal modification and 36.22 ± 2.70% with 140 °C hydrothermal modification, respectively. Due to more decomposition of hemicellulose, the composites expressed lower water absorption and higher thermal stability when the hydrothermal treating temperature exceed 160 °C.     

碳纳米管增强型功能梯度板的屈曲预测

基于一种新的修正偶应力理论,建立了碳纳米管（CNTs）增强型功能梯度板（CNTs/FGP）的屈曲模型。基于最小势能原理和一阶剪切变形理论,推导了该种板模型的平衡微分方程和相应的边界条件,并以四边简支方板的屈曲问题为例,讨论了材料尺度参数、CNTs的体积分数及4种不同CNTs分布形式对CNTs/FGP临界屈曲载荷的影响。结果表明：采用本文模型预测的CNTs/FGP的临界屈曲载荷总是大于传统宏观理论的预测结果,两种理论结果间的差距随着板几何尺寸的减小而逐渐增大;CNTs体积分数的少量增加,即可使板的临界屈曲载荷有明显的提升;CNTs的不同分布形式对临界屈曲载荷有显著的影响,在工程设计中应予以关注。     

针刺工艺参数对炭布网胎增强C/C材料力学性能的影响

采用机械针刺技术, 研究了针刺密度、针刺深度对原位针刺增强碳布网胎迭层预制体结构C/C材料力学性能的影响. 结果表明, 采用高的针刺密度和针刺深度参数, 可获得高的预制体密度和纤维体积分数, 针刺密度和针刺深度对材料层间剪切性能的影响程度比对压缩、弯曲性能的影响程度大, 采用一定密度的碳布网胎时, 在一定范围内, 提高针刺密度和深度能提高材料的力学性能,当针刺密度控制在20～50针/cm²、针刺深度控制在12～16mm时, C/C材料力学性能随两针刺参数值升高而提高; 当针刺密度控制在30针/cm²时, C/C材料弯曲及X-Y向压缩强度分别达到137.68、224MPa, 剪切强度达到15.5MPa, 针刺深度为12mm时, 材料弯曲及X-Y向压缩强度分别达到134.24、213.2MPa, 为较佳的针刺工艺参数.     

Mechanical behaviour and microstructural characterization of 3D four‐directional braided SiO2f/SiO2 composites

In this paper, SiO_2f/SiO₂ composites reinforced by 3D four‐directional braided quartz preform were prepared by the silica sol‐infiltration‐sintering method in a relatively low sintering temperature (450 °C). To characterize the mechanical properties of the composites, mechanical testing was carried out under various loading conditions, including tensile, flexural and shear loading. The microstructure and the fracture behaviour of the 3D four‐directional braided SiO_2f/SiO₂ composites were studied. The tensile strength, flexural strength and the in‐plane shear strength were 30.8 MPa, 64.0 MPa and 22.0 MPa, respectively. The as‐fabricated composite exhibited highly nonlinear stress–strain behaviour under all the three types of loading. The tensile and flexural fracture mechanisms were fully discussed. The fracture mode of the 3D four‐directional braided SiO_2f/SiO₂ composite in the Iosipescu shear testing was based on a mixed mechanism because of the multi‐directivity of the composite. Owing to low sintered temperature, the fibre/matrix interfacial strength was weak. The SiO_2f/SiO₂ composites showed non‐catastrophic behaviour resulting from extensive fibre pull‐out during the failure process.     

纸张材料弹性模量与剪切模量的关系

研究了正交各向异性的纸张的各个材料参数之间的关系,以减少描述纸张材料性能所需的独立参数,并在纸制结构分析中,合理匹配了材料参数。通过对材料单元在纯剪切载荷作用时与纯主应力载荷作用时的两种变形进行力学比较分析,获得了纸张的弹性模量、剪切模量和泊松系数之间的关系,并导出了简单数学公式。该公式在纸制结构设计、振动分析以及有限元计算等方面有实用的意义。