共查询到19条相似文献,搜索用时 171 毫秒
1.
赵永景 《中国新技术新产品》2019,(6)
为了推动工业发展,保证氧化铝生产质量与效率,需要合理应用管式降膜蒸发器,并对其进行改造。首先介绍管式降膜蒸发器设备以及运行原理,对其进行理解,其次分析了目前设备的运行现状,明确以双流程技术进行改造的必要性,再次阐述了管式降膜蒸发器双流程技术在氧化铝生产中的应用,最后则总结了改造之后的蒸发器在氧化铝生产中应用的作用,了解到这一改造的优势,并且得出结论,使用管式降膜蒸发器进行氧化铝生产,无论是生产效率还是成本都有重要意义。 相似文献
2.
3.
4.
蒸发器是氧化铝生产的主要设备之一,也是氧化铝厂能耗最大的设备,降低管式降膜蒸发器能耗,有着十分重要的意义,特别是应对目前的金融危机,降低管式降膜蒸发器能耗,降低生产成本,其意义就更为重要。如何降低管式降膜蒸发器的能耗?有以下几点思考。 相似文献
5.
钢管厂热镀锌车间噪声源识别与控制 总被引:1,自引:0,他引:1
通过对某钢管厂热镀锌车间噪声源测量与分析,指出内吹管及风机是主要的环境噪声污染源,研究了内吹管工艺特征与气流噪声控制策略,优化了风机噪声控制方案.噪声治理工程实施结果表明,内吹管气流噪声瞬时峰值降低了10~15dB(A),风机噪声等效声级值降低了25dB(A),厂界噪声瞬时峰值降低了20dB(A)以上,收到了良好的工程效果. 相似文献
6.
7.
冷凝器和蒸发器是压缩式制冷空调机组中的重要设备,其传热系数的高低直接影响机组的效率和成本.采用强化传热技术是提高冷凝器与蒸发器传热性能的关键.对于管外冷凝传热强化,在Turbo-C管的基础上,将翅片从翅顶到翅根完全割裂,形成断裂的三维翅片管,以减少表面张力作用下冷凝液在传热管表面粘滞特性对传热的影响.采用螺旋隔板替代冷凝器和干式蒸发器的弓型隔板,能改善壳程流体的流动与传热性能;针对降膜蒸发器的降膜蒸发区与满液蒸发区的不同特点,应分别采用不同类型的强化管,以提高蒸发器传热系数. 相似文献
8.
冷凝器和蒸发器是压缩式制冷空调机组中的重要设备,其传热系数的高低直接影响机组的效率和成本。采用强化传热技术是提高冷凝器与蒸发器传热性能的关键。对于管外冷凝传热强化,在Turbo-C管的基础上,将翅片从翅顶到翅根完全割裂,形成断裂的三维翅片管,以减少表面张力作用下冷凝液在传热管表面粘滞特性对传热的影响。采用螺旋隔板替代冷凝器和干式蒸发器的弓型隔板,能改善壳程流体的流动与传热性能;针对降膜蒸发器的降膜蒸发区与满液蒸发区的不同特点,应分别采用不同类型的强化管,以提高蒸发器传热系数。 相似文献
9.
调频信号发射超声成像的参数优化与成像实验 总被引:1,自引:0,他引:1
研究调频信号发射超声成像中影响成像质量的各种参数,提高现有超声图像的信号噪声比.用仿真计算和声学实验来研究不同调频超声信号发射参数下的成像质量.增加超声发射能量,提高图像的信号噪声比;同时,采用相关算法对接收的超声信号解码,保证图像的轴向精度不会下降.优化了调频信号发射超声成像的发射参数,并得到了仿体的B型超声图像,此图像的质量优于传统成像方法的图像质量.该成像方法能够提高超声图像的信号噪声比,尤其是提高超声衰减严重的深部组织图像的信号噪声比. 相似文献
10.
11.
以汽车尾气为热源,建立蒸汽喷射制冷循环的数学模型。针对汽车蒸汽喷射制冷系统的特点,设计应用于汽车蒸汽喷射制冷系统的模糊自适应PID控制器,并与PID控制算法进行对比研究。仿真结果表明,模糊自适应PID控制器在变负荷、变工况等条件下都优于PID控制器,为蒸汽喷射制冷在汽车空调中的应用提供可行性方案。 相似文献
12.
13.
14.
Keith E Herold Lawrence A Howe Reinhard Radermacher 《International Journal of Refrigeration》1991,14(5)
Hybrid refrigeration cycles which combine a mechanical compressor and an absorption cycle in such a way that they share a single evaporator were analysed. The motivation for the investigation of hybrid cycles was the need to more efficiently utilize the output of an internal combustion engine. The hybrid cycles make efficient use of both the work and the heat output of an engine. Performance calculations are reported for a promising cycle which utilizes LiBr-H2O as the working fluid. For this working fluid, the refrigerant is water. Owing to the potential sensitivity of the absorption cycle components to oil contamination, the cycle was analysed assuming an oil-free steam compressor (screw design). Although oil-free steam compressors are available, they are used only sparingly in the industry. The capital cost for such a compressor is very high and the isentropic efficiency of the available units is low. This combination of high cost and low performance results in poor economics for the hybrid cycle based on the available technology. However, the cycle has significant potential from a thermodynamic viewpoint and it provides an incentive for compressor manufacturers to refine the oil-free steam compression technology. 相似文献
15.
16.
为满足大型公共建筑节能降耗的要求,研发一种高能效离心式冷水机组。相对传统离心式冷水机组,该机组主要有3个方面的技术特点:平面多级射流配液技术,增效两级压缩技术,多重防喘振技术。综合以上技术制造一台两级压缩离心式冷水机组样机,并按美国标准和国内行业标准进行型式试验。试验结果表明:采用带经济器的增效两级压缩技术和依靠降膜蒸发器自带布液器的均匀射流配液技术,使机组能效比提升6%~8%,多重防喘振技术能够保证机组的稳定运行。 相似文献
17.
3D‐Printed,All‐in‐One Evaporator for High‐Efficiency Solar Steam Generation under 1 Sun Illumination 下载免费PDF全文
Yiju Li Tingting Gao Zhi Yang Chaoji Chen Wei Luo Jianwei Song Emily Hitz Chao Jia Yubing Zhou Boyang Liu Bao Yang Liangbing Hu 《Advanced materials (Deerfield Beach, Fla.)》2017,29(26)
Using solar energy to generate steam is a clean and sustainable approach to addressing the issue of water shortage. The current challenge for solar steam generation is to develop easy‐to‐manufacture and scalable methods which can convert solar irradiation into exploitable thermal energy with high efficiency. Although various material and structure designs have been reported, high efficiency in solar steam generation usually can be achieved only at concentrated solar illumination. For the first time, 3D printing to construct an all‐in‐one evaporator with a concave structure for high‐efficiency solar steam generation under 1 sun illumination is used. The solar‐steam‐generation device has a high porosity (97.3%) and efficient broadband solar absorption (>97%). The 3D‐printed porous evaporator with intrinsic low thermal conductivity enables heat localization and effectively alleviates thermal dissipation to the bulk water. As a result, the 3D‐printed evaporator has a high solar steam efficiency of 85.6% under 1 sun illumination (1 kW m?2), which is among the best compared with other reported evaporators. The all‐in‐one structure design using the advanced 3D printing fabrication technique offers a new approach to solar energy harvesting for high‐efficiency steam generation. 相似文献
18.
针对目前数据中心空调系统在冷量供应环节普遍存在的能耗大、冷却效果差等问题,本文提出将冷却装置嵌入机柜内部以实现对服务器的定量化精确供冷,利用已通过实验验证的CFD仿真平台,研究了冷却装置的排布方式和运行参数对供冷效果的影响。结果表明:当冷却装置位于两排服务器中间时冷却效果最好,温度合格系数为100%,相比于冷却装置位于两排服务器之下的初始结构,标准差和均匀系数均下降了66.67%。在风机的额定风量达到2000 m^3/h后,增大额定风量对冷却效果的提升明显减弱,在2000~2400 m^3/h范围内,平均温度和最高温度的变化量均在0.5℃左右;当风机的额定风压为250 Pa时,机柜的冷却效果最好,标准差和均匀系数最小,分别为0.66℃和0.016;当进风温度由25℃升至29℃时,服务器整体温度提高,但温度均匀性几乎不受影响,标准差和均匀系数的变化幅度最大值分别仅为0.05℃和0.002。 相似文献