OFDM削波噪声迭代消除算法

高峰均功率比(PAPR)的OFDM信号通过功率放大器的时候会产生非线性干扰,同时降低了放大器的工作效率。传统削波算法可以降低信号的PAPR,但是会带来较大的频谱扩展。作为一种新的削波算法,误差削波可以在降低OFDM信号PAPR值的同时不带来任何频谱扩展。但是这种削波会给信号带来更大的带内干扰噪声。提出了一种OFDM削波噪声迭代估计和消除算法,它能有效的消除由于误差削波带来的噪声。新方法通过建立削波噪声模型,在接收端根据该噪声模型用迭代的方法重新产生削波噪声。仿真结果表明,使用削波噪声消除算法后,使得系统的误码率性能接近未削波信号的水平。     

一种降低OFDM信号峰均功率比的预编码方法

正交频分复用（OFDM）系统的一大缺点就是有较高的峰值平均功率比（PAPR）,大大降低了线性功率放大器的效率。提出了一种用预编码方法,通过引入预编码矩阵将映射后的数据进行功率分配,从而降低OFDM信号的PAPR。该方法不影响频谱效率,不需要进行附加运算以及收发两端的握手信息。计算机仿真表明对传统的64个子载波OFDM系统PAPR有将近9dB的改善。     

RA码在水声OFDM通信系统中的应用研究

正交频分复用(Orthogonal Frequency Division Multiplexing, OFDM)技术由于具有频谱利用率高、抗多径能力强等优点,成为当前水声通信的研究重点和热点,但较高的峰均功率比(Peak-to-Average Power Ratio, PAPR)严重影响了水声OFDM通信系统的性能。采用重复累积码(Repeat Accumulate, RA)作为信道编码方案,并用线性反馈移位寄存器(Linear Feedback Shift Registers, LFSR)代替原RA码结构中的累加器,再通过选择映射(Selective Mapping, SLM)方法降低系统的峰均功率比。计算机仿真和水池实验结果表明,采用改进结构的RA码结合SLM技术能有效降低水声OFDM系统的PAPR,提高系统的性能,具有很好的应用前景。     

浅谈OFDM系统峰均比降低技术

正交频分复用（OFDM）技术以其频谱利用率高和抗频率选择性衰落强等优点，成为下一代移动通信中最具竞争力的关键技术之一，但存在峰均比值（PAPR）较高的问题。本文简要概述了目前降低峰均比的几种方法。     

抑制OFDM信号峰均比对直接检测光传输系统的性能影响

高峰均比是OFDM通信系统的主要缺点之一,光OFDM通信系统也存在同样的问题.本文将联合Hadamard变换和限幅(Clipping)方法抑制峰均功率比算法成功应用到直接检测的光正交频分复用光纤传输实验平台,重点研究了算法对系统误码性能的影响.实验中产生的2.5 Gb/s QPSK OFDM光信号在标准单模光纤中传输1...     

降低MIMO-OFDM系统中PAPR的PTS改进算法

MIMO-OFDM系统存在着严重的峰均功率比(PAPR),制约着MIMO-OFDM技术的应用,降低MIMO-OFDM系统的峰均比(PAPR)成为通信领域的研究热点。主要对概率类技术中的部分传输序列(PTS)算法的方法进行改进和优化。     

一种降低CO-OFDM系统PAPR改进的星座图扩展算法

相干光正交频分复用(CO-OFDM)系统中的较大峰值平均功率比(PAPR)问题会导致严重的光纤非线性效应。本文提出了一种改进的星座图扩展(ACE)算法,取得了更好的PAPR抑制效果。研究表明,ACE算法与凸集投影法(POCS)相结合可减少计算复杂度,但存在峰值再生现象等问题。为此,本文利用抛物峰值抵消(PPC)算法改善迭代过程中的峰值再生现象,并采用星座映射预修正技术提高了收敛速度。采用改进算法对4QAM、29 Gb/s的CO-OFDM系统进行了仿真实验,结果表明改进算法使OFDM信号的PAPR降低了4.41 dB,并且具有更快的收敛速度。     

基于信号匹配追踪的模态参数提取

传统的的设备模态参数提取多是建立在频谱计算的基础上,提取精度受采样频率和时域截断产生的能量泄漏的影响较大。为此,提出了一种基于信号匹配追踪的模态参数提取方法,该方法将Laplace小波作为信号匹配追踪的基元函数;同时引入粒子群算法来实现Laplace小波的参数寻优,克服了传统算法计算复杂的缺点。仿真和实际应用表明,该方法可有效地提取设备的模态参数;且比传统的半功率带宽法具有更高的精度。     

RZF预编码与MMSE-SIC检测联合的大规模MIMO系统预编码设计算法

研究了大规模多输入多输出(MIMO)系统的预编码设计算法。针对大规模MIMO系统通常利用增加用户天线数来提高系统频谱效率的方法会导致用户间干扰增大,从而对系统性能产生负面影响的问题,提出了一种将正则化迫零(RZF)预编码与最小均方误差-串行干扰消除(MMSE-SIC)检测相结合的改进算法。该算法通过在基站端采用RZF预编码对信号进行预处理以平衡用户间干扰和噪声干扰的影响,继而在接收端运用检测性能优异的MMSE-SIC算法来进一步减轻信号中的干扰,从而达到提升系统容量的目的。实验结果表明,这种将RZF预编码与MMSE-SIC检测相结合的改进算法,在用户间干扰较大时具有较好的适用性,且在完全已知和未完全已知信道状态信息情况下的频谱效率均优于传统RZF算法。     

一种多接收通道的增益与相移失配均衡方法

针对多个接收通道增益、相移特性的不一致给测向带来很大误差,提出一种通过标准测试信号,建立通道频率传输特性补偿数据库的方法,对实际接收信号进行精确的通道均衡补偿,有效解决了接收通道增益失配与相移失配问题及减少了测向误差.仿真证明:在比幅法测向系统中.间距d越小,幅度补偿带来的好处越明显;在比相幅法测向系统中,间距d在较大的变化范围内.相位补偿对测向误差都有明显改善.这种算法具有简洁、运算速度快的特点,适合天线数目、信道数目不多的中、小型可移动测向设备.     

Effect of Permeable Crystalline Material on Steel Reinforcement Corrosion of Concrete

Permeable crystalline materialcan permeate into pores and cracks of concrete and catalyze the reaction between Ca(OH) 2and unhydrated cement to generate a great quantity needle non-soluble crystals, which can stop up the pores and cracks of concrete, and increase the impermeability of concrete. This paper reported the results of a study conducted to evaluate steel reinforcement corrosion of concrete specimens uncoated and coated with permeable crystalline material as well as mixed with the permeable crystalline material. The properties evaluated for corrosion test were water impermeability, water absorption, compressive strength and potential. The results of water impermeability, water absorption, compressive strength clearly showed that the permeable crystalline material could prohibit water, any soluble salts and moisture from penetrating the concrete to cause corrosion, leaking, and other problems, and it did increase the compressive strength, which was favorable for protection of corrosion of reinforcing steel. Moreover, it was concluded from the potential-time curve that the steel reinforcement of uncoated specimen was in the state of activation whereas that of other specimens coated and mixed with the permeable crystalline material was in the state of inactivation. Above all, it was indicated that the permeable crystalline materialis very effective to protect the steel reinforcement of concrete from corrosion.     

The Research and Application About "Dry Peeling Off" Technology for Airplane Surface Paint Layer

In this paper, the principle of spurting take off lacquer were introduced; and with orthogonal method the unsaturate polyester was prepared ;it was easy to peel airplane paint layer off with this material and equipment.     

Quality Study of Honeycomb Core Shaping Without Wax Stabilization

Sandwich panels utilizing honeycomb cores result in lightweight, high-strength units that are very rigid. Indeed, they give honeycomb panels the best strength-to-weight ratio of any construction type available. Conventionally, the wax is poured into the cell of the core to strengthen the structure and prevent the core from being crushed during milling. Much time and labor is required to wax, mill, and clean the cores. In this study, the process of pouring wax into the core was skipped. In other words, the cutter directly milled the core. Experiments showed that the compressive strength of the core produced without wax stabilization was only 3% lower than that of cores produced using the traditional method. In addition, the drum peel strengths of cores produced without wax stabilization were 38.4% higher than cores produced using the traditional method, in which residual wax seriously polluted the adhesive. It was also found that eliminating the wax process can reduce costs.     

In-process thermal treatment of polylactic acid in fused deposition modelling

Polylactic acid (PLA) is one of the most widely used open source fused filament fabrication materials due to its ease of extrusion, biodegradability, and mechanical strength. The mechanical strength of PLA largely depends on the proper growth of its semi-crystalline structure, which can be severely impaired by a low rate of crystallization, particularly in open source printers. This can be further aggravated by the non-uniform thermal distribution of heat that causes improper curing among the extruded beads of the printing material. As a result, PLA printed on open source printers does not achieve the best mechanical properties. This research, for the first time, proposes an additive-free solution implemented through a detailed set of experimentation to improve the curing rate through in-process temperature variations to cure the joints among the beads. Scanning electron microscopy (SEM), differential scanning calorimetry (DSC) and Fourier transform infrared (FTIR) spectroscopy is used to confirm the improvements in the bead joints. This work is conducted in two phases of experiments. In the first phase, a full factorial ANOVA is used to investigate various process parameters and the important variables are used in the second phase to print test specimens in four different sets.     

Investigation of the Corrosion Behaviors of HVOF-Sprayed Carbide Cernet Coatings in Molten Al-Zn-Si Alloy Bath

In continuous hot-dip galvanization process the corrosion and chemical stability of the sink roll in the galvanizing bath are important problem which effects on the quality and productivity. In order to protect the sink roll the carbide cermet and/or ceramic coatings were deposited on the surface of the sink roll. The WC-, Cr3 C2-cermet coatings were deposited by high velocity oxygen fuel (HVOF) spray, respectively. The coating samples were immersed in molten Zn-alloy containing 50 wt % aluminum at 833 K for 24 hr and 144 hr, respectively. The inter-diffusion and inter-reaction of Zn, Al and elements in coating and corrosion behaviors of these coatings were investigated by XRD, SEM and EPMA etc. The corrosion mechanisms of the carbide cermet coatings and ceramic coatings in molten High Al-Zn-alloy were approached.     

Fundamental study of adhesion of ice to cooling solid surface (Discussion on influence of copper oxide layer on ice adhesion force)

In many situations, ice often adheres to a cooling solid surface, frequently causing serious accidents. It is critical to clarify the mechanism of ice adhesion to the cooling surface in order to prevent ice adhesion. In a past study, the shearing stresses of two kinds of test plates with a copper surface having the higher thermal conductivity were measured. The shearing stress corresponds to ice adhesion force. Both shearing stresses were significantly different; however, the cause remains unclear.Therefore, the present study focuses on an oxide layer as the main factor causing the difference of both shearing stresses; the influence of the oxide layer formed on shearing stress was discussed. And in the removal and reformation processes of the oxide layer, the time variation of the shearing stress was clarified. Moreover, the relationship between the state of the copper surface and the shearing stress was also clarified by surface analysis.     

重塑标准推行格局 推动LED照明的普及（英文）

正When you are enjoying the green,energy-saving and healthy lighting of IKEA LED luminaire,you may not realize that most of IKEA’s LED bulbs are produced by the LED luminaire smart manufacturing system of Hangzhou Zhongwei Photoelectricity CO.,LTD(ZVISION).No longer enclosed in the laboratory,the product standards are brought into the factory workshop and even to the entire production process.Thus,the standards are promoted and applied in a favorable way by enterprises,benefitting consumers with high quality products.     

Chinese Experts Contribute to ISO＇s New Toy Standards

正The international standard,ISO 8124-6,Safety of toys–Part 6:Certain phthalate esters in toys and children’s products,was officially issued by ISO worldwide on August 15.It was the first time for Chinese experts to lead the ISO standard development in toys industry.The standard was drafted by a group of Chinese experts from SAC/TC for toys and relevant Chinese departments and finally completed by a dedicated international group of experts.ISO 8124-6 makes a substantive breakthrough in the aspects of the scope of toys,limitation of plasticizer types,control of test cost,accuracy of test,operation convenience,etc.,offering the operational guidance for toy manufactures and testing laboratories.     

中国质量(北京)大会(英文)

正Themed on"quality,innovation,development",the first China Quality Conference(Beijing)was held in the Great Hall of the People on September 15.Chinese Premier Li Keqiang delivered an important speech at the conference.State Councilor Yang Jing and Wang Yong attended the conference with over 600 domestic and international representatives from foreign,regional and international quality organizations     

National Working Meeting on Land and Resources Standardization

正The National Working Meeting on Land and Resources Standardization was held in Beijing on July 15,2014.Wang Min,the Deputy-Minister of the Ministry of Land and Resources,and Yin Minghan,the Chief-Engineer of SAC addressed the meeting.Representatives from relevant competent departments and technical committees were present.The meeting aims to summarize work,discuss existing problems and make clear working thoughts,promoting standardization work of land and resources to a new level.Wang Min pointed out that the standardization work of land and resources should be centered on the basic principles of"protecting land and resources dutifully,intensively and economically utilizing land and resources,and making all-out efforts to safeguard the public’s rights and interests",highlighted the