SiO2对Al2O3凝胶纤维相变的影响

以尿素催化硅酸乙酯水解制得SiO2溶胶。采用29Si NMR、27 Al NMR、FT-IR、TEM、DTA、XRD和SEM等对SiO2溶胶、Al2O3凝胶纤维化学结构和微观结构研究结果表明,该SiO2溶胶稳定性好,含有大量的单硅酸Si(OH)4,能和Al2O3表面的Al—OH反应生成Al—O—Si键而有效地将其包裹,从而阻止了过渡态Al2O3微晶的相互接触,抑制了α-Al2O3的成核和生长。     

莫来石纤维增强SiO2气凝胶复合材料的制备及性能研究

以正硅酸乙酯为硅源,采用溶胶-凝胶及超临界干燥技术制备了掺杂莫来石纤维的SiO2气凝胶复合材料,并对材料的热学性能和力学性能进行了测试,结果表明:SiO2气凝胶复合材料的热导率与其密度、温度和纤维添加量有关;添加莫来石纤维可以明显提高SiO2气凝胶的弹性模量和机械强度,改善材料的力学性能;莫来石纤维添加量控制在3%左右可以使SiO2气凝胶材料保持较低的热导率和较高的机械强度.     

Al2O3-SiO2复合膜的疏水改性及表征

采用溶胶-凝胶法制备Al2O3-SiO2复合薄膜,通过添加二甲基二乙氧基硅烷(DDS)对其进行疏水改性。研究了DDS添加量对复合溶胶体系稳定性和复合膜表面疏水性的影响,采用接触角测量、红外光谱(IR)、热重分析(TG-DTG)、原子力显微镜(AMF)对样品进行表征。结果表明,对于Al2O3∶SiO2(mol/mol)=1∶2比例下制得的复合膜,随着DDS的加入,薄膜表面疏水性明显增强,当DDS加入过多时,会影响复合溶胶的稳定性,实验确定DDS加入量的最佳值为1%(体积分数);DDS的加入没有破坏复合膜的网格结构,复合膜仍以SiO2颗粒为骨架;经200℃热处理后,可得到具有良好的疏水性能的复合膜。     

SiO2/TiO2复合气凝胶的孔道结构研究

为了在常压干燥下制备高比表面积且具有多级孔道结构的SiO2/TiO2复合气凝胶,以正硅酸乙酯、钛酸丁酯为原料,利用低聚体聚合将分相平行引入到溶胶凝胶过程中,获得SiO2/TiO2醇凝胶,并通过溶剂替换技术实现气凝胶的常压干燥制备.不同硅钛比气凝胶的内部结构研究表明:合成的气凝胶是由纳米SiO2和TiO2颗粒分散复合而成的介孔块体,其中Ti—O—Ti、Si—O—Si和Ti—O—Si键相互交织.气凝胶的结构变化是分相与溶胶凝胶过程相互竞争的结果.Si含量能显著改善气凝胶的结构,当n(Ti)∶n(Si)为3∶1时,比表面积高达712.2 m2/g,平均孔径为3.36 nm;当n(Ti)∶n(Si)为1.5∶1时,复合气凝胶具有明显双连续孔道,比表面积高,同时孔状结构清晰.     

复合纤维增强疏水SiO2气凝胶的制备及其性能

以正硅酸乙酯(TEOS)为前驱体,复合纤维为增强相,采用溶胶-凝胶法和常压干燥技术制备了纤维增强疏水SiO_2气凝胶复合材料。利用傅里叶变换红外光谱仪、扫描电子显微镜、比表面积分析仪等手段对气凝胶的化学组成、形貌及结构等进行了分析,并且测量了样品的密度和抗折强度。结果表明:经常压干燥制备的SiO_2气凝胶复合材料加工成块性较好,密度在0.27g/cm~3左右,比表面积达到878.544m~2/g;随着复合纤维的掺入,凝胶填充了纤维之间的大部分微米空隙,并与纤维形成了比较密实的结构,复合材料的抗折强度提高到了1.53 MPa,使得材料有较好的韧性,适用于不规则形状的隔热。     

CoAl2O4/Al2O3纳米复合陶瓷的结构与表征

利用溶胶-凝胶方法制备了的CoAl2O4/Al2O3纳米复合陶瓷,并用X-ray分析(XRD)、红外光谱(IR)和扫描电镜分析(SEM)对其结构进行了分析.结果表明,随Al2O3含量增多,CoAl2O4尖晶石相从CoAl2O4/Al2O3凝胶中的析晶温度升高.SEM形貌也说明,随Al2O3含量增多,CoAl2O4/Al2O3陶瓷中形成一定的层状结构.     

ZrO2纤维/莫来石轻质复合材料的凝胶注模制备及其增韧机理研究

采用凝胶注模成型工艺制备了ZrO2纤维增韧莫来石复合陶瓷材料.借助透射电子显微镜(TEM)、扫描电子显微镜(SEM)、平板导热仪、单边切口梁法(SENB)等测试手段对样品微观形貌、导热系数、断裂韧性等进行研究;研究了分散剂对凝胶注模浆料团聚体的影响;讨论了ZrO2纤维增韧莫来石复合材料的增韧机理;概述了同时获得高韧性和高强度材料的途径.结果表明:添加ZrO2纤维能够明显提高莫来石的断裂韧性;当ZrO2纤维添加量(体积分数)为25％左右时可使莫来石轻质耐火复合材料兼具较低的热导率(λ=0.35 W·m-1·K-1,298 K)和优异的综合力学性能(KIC=7.6 MPa·m1/2,σb=270 MPa).     

SiO2气凝胶/中间相沥青基泡沫炭复合材料的制备与表征

以正硅酸乙酯、乙醇和去离子水为原料,采用溶胶-凝胶法制备了SiO2溶胶;并以煤沥青为原料,采用自挥发发泡法制备了中间相沥青基泡沫炭。然后采用浸渍工艺将SiO2溶胶和中间相沥青基泡沫炭在常压下进行复合,制备了SiO2气凝胶/中间相沥青基泡沫炭复合隔热材料。利用XRD、SEM、热导仪和万能试验机等设备分别研究了SiO2气凝胶、中间相沥青基泡沫炭以及SiO2气凝胶/中间相沥青基泡沫炭复合材料的结构和性能。结果表明,所制备的复合材料具有一定的力学性能,同时其隔热性能优于单一泡沫炭的隔热性能,有望成为一种新型的隔热材料。     

热处理温度对TiO2/SiO2复合气凝胶光催化性能的影响

采用溶胶–凝胶法在常压下经不同温度热处理制备了TiO2/SiO2复合气凝胶光催化剂,利用XRD、TGA和BET等手段对其微观结构进行表征,以甲基橙溶液光催化降解实验评价其光催化性能,研究了热处理温度对TiO2/SiO2复合气凝胶的微观结构及光催化性能影响规律.结果表明:随着热处理温度升高,TiO2/SiO2复合气凝胶中锐钛矿结晶度升高,晶粒尺寸增大,比表面积减小,使TiO2/SiO2复合气凝胶对甲基橙溶液的光催化降解活性呈现先升后降的变化趋势.当热处理温度为700℃左右,紫外光照20 min TiO2/SiO2复合气凝胶对甲基橙溶液的降解率达到95.4%.     

SiO2/C/M气凝胶纳米复合材料的结构及吸波性能

本文在SiO2/M(M=Fe,Co,i)复合气凝胶骨架上采用气相催化裂解乙炔的方法合成出SiO2/C/M气凝胶纳米复合材料,用扫描电镜、比表面分析仪、激光导热仪等对材料的结构和物理性能进行了表征,并初步测试了其电磁吸波性能.结果表明,在SiO2/C/M气凝胶纳米复合材料中,碳元素一般以纤维形式均匀分布于气凝胶骨架中,该材料具有低密度,低热导率().05～0.2W/mk),在2mm厚度,8-18GHz的范围内有一定的吸波性能,且吸波性能随频率升高而增加.     

Preparation of ZrO2-CeO2 and HfO2-CeO2 nanopowders

We prepared weakly agglomerated powders of ZrO₂-CeO₂ and HfO₂-CeO₂ solid solutions 5–8 nm in particle size, consisting of monoclinic and tetragonal phases. After heat treatment at 1200°C, the crystallite size was 30 and 14 nm, respectively. We also examined the effect of precipitate freeze drying on the crystallization of hafnia-based solid solutions containing up to 20 mol % CeO₂.     

Comparison of the Electronic Structures of La2CuO4, Sr2CuO2Cl2, and Sr2CuO2F2

First-principles cluster calculations are reported of the local electronic structure of the three compounds: La₂CuO₄, Sr₂CuO₂Cl₂, and Sr₂CuO₂F₂. The copper ${\text{3d}}_{x^2 - y^2 } $ and the planar oxygen 2p _σ atomic orbitals exhibit a similar degree of covalency. The out-of-plane orbitals, however, are quite different with the ${\text{3}}d_{3z^2 - r^2 } $ atomic orbital lowered significantly in energy for chlorine and fluorine apical positions.     

Thermoelectric power of single-phase samples of Tl2CaBa2Cu2O y and Ba2CaSr2Cu2O y

Single-phase 2122 samples of thallium and bismuth superconductors were made by the precursor matrix method. The thermopower of these samples was measured in the temperature range 250 K-T _c . The thermopower was positive and decreased linearly with increasing temperature aboveT _c (onset). The exponential enhancement of thermopower seen in the undoped and doped YBCO was not observed in these samples. The linear variation of thermopower can be explained on the basis of either a two-band model or a narrow band model.     

VLE data for CO2-CF2Cl2, N2-CO2, N2-CF2Cl2 and N2-CO2-CF2Cl

Knowledge about vapour-liquid (VLE) is required as a basis of reliable calculations for separation processes. Correlations available for the prediction of T, p, x, y data are less accurate for mixtures at high pressures and mixtures containing supercritical components. The results of VLE experiments are reported and compared with data calculated with equations of state.     

SiO2—TiO2—ZrO2系涂层的制备及其特性

用溶胶－凝胶法（sol-gel method）在不锈钢表面制备了SiO2-TiO2-ZrO2系无机氧化膜（STZ）。用DTA／TG、IR、XRD和SEM等手段研究了涂层制备时由凝胶向玻璃态的转变以及涂层薄膜的显微结构特点，考察了涂层对基体的保护效果。试验结果表明，在溶胶至凝胶最终转变为无机氧化物的过程中形成了无机网络，Si^4 和Zr^4 充当了网络骨架的形成离子。涂层为无定型玻璃态，其间混有石英、锐钛矿或金红石等微晶。     

Structure of Na2O·2TiO2 glass

X-ray radial distribution analysis and Raman spectroscopic measurement were carried out on Na₂O-2TiO₂ glass prepared by twin-roller quenching method. It is found that four-coordinated Ti⁴⁺ ions may be predominant over six-coordinated ones in the present glass. It is also found that the fraction of six-coordinated Ti⁴⁺ ions is larger in the present glass than in K₂O·2TiO₂ and Cs₂O·2TiO₂ glasses. Poorer glass-forming ability of the Na₂O-TiO₂ system compared with the K₂O-TiO₂ and Cs₂O-TiO₂ systems is ascribed to a larger fraction of TiO₆ octahedron for the former system.     

Elastic and Electronic Properties of Superconducting CaPd 2 As 2 and SrPd 2 As 2 vs. Non-superconducting BaPd 2 As 2

The first-principles calculations were performed to predict the elastic and electronic properties of the superconducting ThCr₂Si₂-type phases CaPd₂As₂ and SrPd₂As₂ in comparison with the non-superconducting CeMg₂Si₂-type phase BaPd₂As₂. Besides, the same properties were compared for CeMg₂Si₂- and ThCr₂Si₂-type polymorphs of BaPd₂As₂. We found that all these phases are mechanically stable and belong to soft materials with low hardness. The near-Fermi region is formed by the valence states of the blocks [Pd₂As₂] with decisive contributions of Pd 4d states. The values of N(E _F) increase in the sequence: CaPd₂As₂ < SrPd₂As₂ < BaPd₂As₂, i.e. in the reverse sequence relative to the transition temperatures T _C. Thus, the change in T _C cannot be explained by the electronic factor, i.e. by the simple correlation T _C～N(E _F). Most likely the decrease in T _C in the sequence CaPd₂As₂ → SrPd₂As₂ and the absence of a superconducting transition in BaPd₂As₂ are related to the structural factors and the peculiarities of the electron–phonon coupling mechanism.     

Investigation of Instability of Lattice of Bi_2Sr_2CaCu_2O_x

Bi2Sr2CaCu2Ox superconductor was studied by differential scanning calorimetry (DSC) and thermogravimetry (TG) in different atmospheres. It is discovered that there is a thermal anomaly in the DSC curve, associated with a weight loss in the TG curve before the melting of the sample. Careful thermal analysis and high temperature X-ray diffraction reveal that the thermal anomaly and the weight loss show an instability of the crystalline Iattice. By annealing the sample in oxygen and argon, respectively and then by TC measurement and thermal analysis, the coincidence of transition temperature with the instability is found. The coincidence is further confirmed by Y-doped 2212 phase.