不同介质中水热合成纳米TiO2粉体及其光催化性能研究

以钛酸四丁酯为原料,采用水热法分别以蒸馏水、有机小分子化合物(正丁醇、丙二酸和乙二胺水溶液)和无机酸(HNO3、H2SO4和HCl)为介质合成了TiO2纳米粉体.通过XRD和TEM对所得TiO2粉体进行了表征,研究不同介质对所得TiO2粉体的晶相组成、颗粒尺寸及形貌的影响.结果表明:以蒸馏水为介质时所得锐钛矿TiO2的颗粒尺寸分布不均匀;有机化合物抑制锐钛矿型TiO2各向异性生长趋势的能力为:正丁醇＞丙二酸＞乙二胺;相同实验条件下,HCl、H2SO4及HNO3体系中分别获得金红石、锐钛矿及锐钛矿和金红石混晶TiO2.光催化降解甲基橙的研究表明,锐钛矿和金红石混晶TiO2的光催化活性要高于纯锐钛矿结构;纯金红石型TiO2的光催化活性最差.     

钒掺杂对TiO_2晶型转变的影响

以钛酸四丁酯为原料,利用溶胶-凝胶法制备了纯TiO2粉体和钒(V)掺杂的TiO2粉体,并利用TG-DSC,XRD,SEM等方法对样品进行了表征。结果表明:V的掺杂促进了TiO2粒子由锐钛矿型向金红石型的转变,并使晶型转变温度范围变窄;TiO2晶粒的尺寸随焙烧温度的升高逐渐长大,随掺杂量的增加逐渐减小。TiO2粉体粒子在锐钛矿型状态下,颗粒分散均匀,并且无明显团聚现象。因此,V掺杂TiO2具有良好的光催化活性。     

纳米TiO2薄膜的制备及其光催化性能研究

采用溶胶-凝胶(Sol-gel)法在玻璃衬底上制备了纳米TiO2薄膜.采用X射线衍射仪(XRD)、紫外可见一光谱(UV/vis)和原子力显微镜(AFM)对纳米TiO2进行表征.结果表明,经300～700℃退火得到的TiO2粉体呈锐钛矿相,经800℃退火得到了锐钛矿相与金红石相的混合晶相,经900℃退火完全转化为金红石相.薄膜表面粒子分布均匀,表面平均粗糙度为1.54nm,该薄膜具有较高的光催化活性,可直接用于光催化降解有机物等领域,具有广阔的应用前景.     

Fe、S共掺杂纳米TiO2的制备及性能研究

采用溶胶-凝胶法,以硫脲和三氯化铁为掺杂剂,制备了Fe-TiO2、S-TiO2和S-Fe-TiO2纳米光催化剂.通过XRD、SEM等方法对掺杂纳米TiO2进行了表征,以甲基橙为模型化合物对纳米TiO2粉体的光催化活性进行了评价.结果表明;纯TiO2、掺Fe-TiO2粉体全部为锐钛矿相,S-TiO2粉体中金红石相占8.1%,S-Fe-TiO2粉体中金红石相占26.9%.S和Fe、S共掺杂引起金红石相变温度的降低.掺Fe的纳米TiO2粉体粒子团聚少,分散要均匀,掺S和Fe、S共掺的TiO2粉体颗粒团聚现象较严重.S-TiO2和Fe-TiO2光催化荆在紫外光和日光灯下光催化活性都较好,而Fe-S-TiO2光催化活性没有提高.     

低温制备锐钛矿型TiO2溶胶的性能研究

采用溶胶-凝胶法,以水为溶剂,在低于70℃下直接合成纳米锐钛矿型TiO2溶胶,研究了反应温度、pH值对溶胶晶型、晶粒大小和稳定性的影响.以不同光照下对亚甲基蓝的降解,评价了溶胶的光催化活性.结果表明:较低pH值下溶胶中的TiO2出现了金红石相与锐钛矿相组成的混晶相,而pH值相对较高时则得到纯锐钛矿相TiO2;在紫外光、日光灯和太阳光下,与P25对亚甲基蓝的降解相比,同等条件下所制备的TiO2溶胶显示出更好的光催化活性;混晶相TiO2溶胶的光催化性优于纯锐钛矿相TiO2溶胶.     

Eu3+和Sm3+共掺杂TiO2光催化剂的协同效应

采用溶胶-凝胶法制备了纯TiO2和Eu3+/Sm3+共掺杂TiO2复合粉体,采用XRD,DRS和SEM等技术进行表征,以亚甲基蓝(methylene blue,MB)的光催化降解为目标反应,评价了其光催化活性,探讨了Eu3+/Sm3+共掺杂对TiO2粉体光催化的影响机制.结果表明,Eu3+/Sm3+共掺杂可以显著提高TiO2粉体光催化活性,Eu3+/Sm3+共掺杂在TiO2粉体中产生协同作用,可以抑制TiO2由锐钛矿相向金红石相转变,使TiO2的粒径减小.Eu3+/Sm3+共掺杂增大了TiO2粉体的晶格畸变,使TiO2粉体吸收带边蓝移.当Eu3+/Sm3+的掺杂量分别为0.05%和0.1%,TiO2光催化活性最高,光催化降解率达到84.8%.     

不同水解抑制剂制备纳米TiO_2薄膜及其性能

本文以钛酸丁酯、三乙醇胺、冰醋酸、盐酸等为主要原料,采用溶胶-凝胶(sol-gel)法和旋转涂膜工艺在玻璃衬底上制备均匀、透明的纳米TiO2薄膜。利用X射线衍射(XRD)、紫外-可见光谱(UV/vis)和原子力显微镜(AFM)对纳米TiO2进行表征,结果显示:经500℃退火后,三乙醇胺、冰醋酸作水解抑制剂制备的TiO2粉体为锐钛矿晶相,而盐酸作水解抑制剂制备的TiO2粉体为锐钛矿、金红石和板钛矿的混合晶相;纳米TiO2薄膜存在光催化活性和吸收带边不同程度的蓝移,且用三乙醇胺制备的TiO2薄膜的蓝移最大,光催化活性最强。     

TiO_2纳米粉体的溶胶-凝胶工艺制备和光催化活性表征

通过溶胶 -凝胶工艺制备了锐钛矿型TiO2 纳米粉体 ,TiO2 粉体由 40～ 80nm的球形颗粒组成。XPS研究表明 :TiO2 纳米粉体中主要含有Ti和O元素 ,未发现其它杂质元素 ,O/Ti的原子比为 2 .14,其中含有一定量的羟基 (-OH)。甲基橙水溶液的光催化降解实验表明 :溶胶 -凝胶工艺制备的锐钛矿型TiO2 纳米粉体的光催化活性明显高于普通TiO2 粉体。     

TiO_2纳米粉体的溶胶-凝胶工艺制备和光催化活性表征

通过溶胶 -凝胶工艺制备了锐钛矿型TiO2 纳米粉体 ,TiO2 粉体由 40～ 80nm的球形颗粒组成。XPS研究表明 :TiO2 纳米粉体中主要含有Ti和O元素 ,未发现其它杂质元素 ,O/Ti的原子比为 2 .14,其中含有一定量的羟基 (-OH)。甲基橙水溶液的光催化降解实验表明 :溶胶 -凝胶工艺制备的锐钛矿型TiO2 纳米粉体的光催化活性明显高于普通TiO2 粉体。     

高活性TiO2纳米晶的酸催化Sol-Gel法制备与表征

采用酸催化的溶胶-凝胶法制备出了纳米TiO2光催化剂，以甲基橙的光催化降解为探针反应，评价了其光催化活性．运用XRD、TEM、FT—IR以及PL光谱技术对纳米TiO2的微晶尺寸、晶体结构、表面组成和性能进行表征．结果表明，400℃焙烧的TiO2纳米粒子的颗粒形貌为近球形，晶粒尺寸为11．69 nm，样品分散性良好的锐钛矿型结构．在光催化降解甲基橙的实验中，400℃焙烧的TiO2纳米粒子表现出最高的光催化活性，这与表征结果一致．此外，550℃和650℃焙烧的具有锐钛矿型和金红石型混晶结构的TiO2纳米粒子，无混晶协同促进效应．     

The Research of Anti-Wear Properties of Organomolybdenum Compounds in the Engine Oils

A four-ball tester was used to evaluate the anti-wear performance of three kinds of organomolybdemun compounds in the engine oils, i. e., molybdenum dialkyldithiophosphate (MoDDP), molybdenum dialkyldithiocarbamate ( MoDTC), and sulphur and phosphorus freeorganomolybdeum (Molybdate). The results indicate that a low concentration of MoDDP doesn' t improve the anti-wear properties of the commercial engine oils, but a high concentration of MoDDP can obviously improve the anti-wear properties and the load-carrying capacity of the engine oils. MoDTC doesn' t improve the antiwear properties of the engine oils, but worsens the anti-wear properties of the oils. Signifi can timprove ment of frictional and wear characteristics is obtained with Molybdate added in the commercial engine oils and the formulated oils.     

Certification Becomes Important for the I Quality; and Safety Supervision of the Chinese Liquor Sector

The end of 2007, over 200 unit products of more than 80 Chinese firms have passed the quality grade certification for liquor products. These products involve distilled spirits, beer, wine, yellow wine, fruit syrup wine and others, and cover over 80% of the national top-branded liquor products.……     

Deposition and Coating Properties on CVD Tungsten

Surface characterization and microstructure studies are performed on chemical vapor deposited (CVD) tungsten coating. There is about 2 μm thickness diffusion layer of tungsten in the molybdenum substrate. The thermal shock test shows tungsten coating has good adhesion with molybdenum substrate, but the elements of oxygen and carbon in the tungsten coating have the bad affection to the adhesion. The result of high-temperature diffusion experiment is the diffusion rate from molybdenum substrate to tungsten coating is faster.     

Analysis of marine hydrobiont lipid extracts as possible cryoprotective agents

We studied a combined effect of the cryoprotectants both of lipid and carbohydrate origin at the presence of DMSO or without it on cell viability and the RNA synthesis in the embryonic mollusc and echinoderm cell cultures obtained at different developmental stages. Cryoprotective properties of exogenous lipids correlated with their thermotropic behavior. Lipid extracts from marine hydrobiontes, which thermal transitions are characterized by relatively small part of calorimetric thermogram area lying at temperatures above 0 °C (6–18%), were found to possess a considerable cryoprotective activity. The results are discussed in relation to the prediction of the cryoprotective activity of lipid extracts for marine animal cells. In addition, it was found that marine invertebrate cells can be cryopreserved without DMSO at the presence of trehalose and lipid extracts of some marine hydrobiontes.     

Low-Temperature Properties of Silver

Pure silver is used extensively in the preparation of high-temperature superconductor wires, tapes, films, and other configurations in which the silver not only shields the superconducting material from the surrounding materials, but also provides a degree of flexibility and strain relief, as well as stabilization and low-resistance electrical contact. Silver is relatively expensive, but at this stage of superconductor development, its unique combination of properties seems to offer the only reasonable means of achieving usable lengths of conductor. In this role, the low-temperature physical (electrical, thermal, magnetic, optical) and mechanical properties of the silver all become important. Here we present a collection of properties data extracted from the cryogenic literature and, to the extent possible, selected for reliability.     

Early ironwork in Biscay: Survey,excavation, experimentation and materials characterization. An integral study of the mountainside ironworks (ferrerías de monte or “haizeolak”)

ABSTRACT

The production of iron in Biscay (Basque Country, Spain) has been a hallmark of this territory of the North of the Iberian Peninsula throughout its history. The Archaeology team of the Basque Country Mining Museum has spent 13 years, so far, studying the origins of this activity through the evidences left at the old pre-hydraulic iron production workshops known as mountainside ironworks (ferrerías de monte) or haizeolak. It has catalogued 170 archaeometallurgical sites of this type in Biscay, and the archeological excavation of some of them has led to the knowledge of the different stages of the production process that took place in these workshops. The team has also experimentally reproduced the work carried out in a mountainside ironworks from the High Middle Ages, and it has currently started the characterization process of this type of activity through the study of the collected materials.     

Mechanism Study on the Wear of CrAlTiN Coated High-Speed Steel Twist Drills Under Dry Cutting Conditions

As demands about environment protection are growing up, dry cutting technology is getting more and more concerns from all over the world. Main works performed here are study on dry cutting performances and wear mechanisms of M2high-speed steel (HSS) twist drills with CrAlTiN multicomponent coatings, which was deposited using magnetron sputter ion plating system, in drilling 45 and 30CrMnSiA steel, and their comparisons to those in drilling the same steel but using monolayer CrN and commercial TiN coated drills. Drilling performances of drills are evaluated mainly through the measurements of width on outer corner flank land and the cutting forces. Results show that performances of CrAlTiN coated drills are better than those of monolayer CrN and TiN coated drills. In drilling 45 and 30CrMnSiA steel, the average tool life of the CrAlTiN coated drills are 17.2 and 11.8 times higher than those of the uncoated drills. Observing wear of the drill with scanning electronic microscope, results show that there is no crack or spallation of the CrAlTiN coatings in wear zones. Main mechanism of the wear here is adhesion.     

Study on Bond Ability of Arc-Spraying Coatings with Different Surface Pretreatment on Cast-Iron

Arc spraying coatings are widely used in various applications, but uncommon in cast iron substrate. Different surface pretreatment technology is tested on substrates of gray cast iron. Surface roughness and residual stress were measured by TR200 and X-ray diffraction analyzer. Influence of different surface pretreatment methods ( dry blasting and fusebond) on roughness and residual stress was analyzed. The arc-sprayed coatings of wire 3Cr13 (φ2mm) on gray cast iron substrate is studied. The microstructure and interface of bonding layer were observed by SEM. The bond strength was taken by tensile test. Results show that bond strength with grit blasting is higher than fuse-bond; it is feasible to make wire 3Cr13 coating with arc spraying on cast iron substrate roughened by grit blasting.     

Structural Characteristics of TiO2 Ceramic Coating by Micro-Plasma Oxidation

TiO2 ceramic coatings with thickness of 20 μm were formed on the surface of pure titanium by micro-plasma oxidation. Their micro-structures were investigated by by using X-ray diffraction and their surface images were detected by using scan electronic microscope. There were three kinds of TiO2 coatings, pure anatase type TiO2 phase, mixed phases consisted of rutile type TiO2 phase and anatase type TiO2 phase, pure rutile type TiO2 phase. The coating surface with the pure anatase type TiO2 phase is rough, while the coating surface with the pure rutile type TiO2phase is smooth. The upper coating surface with the mixed type TiO2 phases is anatase type TiO2 structure and the subsurface of the TiO2 coating is rutile type TiO2structure.     

Evaluation of fatigue life of steel using steel grain size

The insightful discussion of the relationship between the construction of metallographic and fatigue life and proposition of mathematical relationships describing this relationship was conducted in the paper. This paper presents a method for estimating the fatigue life, based on the construction of the microstructural material taking into account the grain size and the participation of ferrite and pearlite phase.